Search Documents

By W. C. Hagel, H. J. Beattie

Variations in the secondary phase reactions of six nickel-and cobalt-base alloys were determined as a function of solu-tioning from 1700" to 2200°F and aging at 1200" to 1800° F for times up to 1000 hr. Room-temperature impact energies and hardnesses were also measured. Precipitation hardening of these alloys results mainly from the grain-interior formation of ? '; M23C6 appears principally as grazn-boundary cells which can be eliminated by intermediate high-temperature aging treatments. Cellular precipitation of ?' occurs up to 1500°F in cobalt-nickel alloys devoid of chromium, where precipitation by this mode can be attributed to a large degree of lattice disvegistery. THE usefulness of nickel- and cobalt-base alloys is dependent on balancing the strength and ductility provided by the solid-solution matrix, dislocation-type subboundaries, grain-boundary phases and genera1 precipitation within individual grains. Since equilibrium relationships for complex austenitic alloys are not easily fixed, a satisfactory balance

Jan 1, 1960

By J. M. Morris

The point to be made most clear in this paper is the economic value of flotation in the Benguet mill flow sheet. It is rather a statement of effect with no attempt at a technical explanation of the cause. Certain well-known, easily understood reagents, mechanisms and principles have been adapted to the conditions at Benguet, and have proved to be more successful than was demonstrated in the laboratory. The mechanical and metallurgical development of this particular operation was arrived at by trial and error, with fortunately very little error. Changes were slow, of necessity, which in the end proved a blessing in that time was afforded for observation and analysis of the disturbing factors; and as a result each change was a definite step towards higher efficiency. Many of these steps were unpredictable from laboratory work because of the varied and differing characteristics of ores met with in daily operation of the mill, which were practically impossible to reproduce on a laboratory scale. The Benguet mill receives daily ores that differ as much as if they were delivered from three different properties. There is first the surface and upper-level zone, which produces an oxidized secondary ore containing considerable iron oxide, manganese oxide and some organic matter. Formerly, most of this ore consisted of very soft fill with some hard rock mixed in. It also contained an unusual amount of iron and aluminum sulfate, which formed hydrates upon entering the alkaline cyanide solution and caused excessive frothing. When flotation was introduced in the Benguet mill the general characteristics of this upper-level ore had changed considerably, in that it was practically all newly mined, fairly hard ore. It still contained many of the same disturbing elements, but was somewhat simpler to treat than formerly. The small proportion of fines is still troublesome in flotation, and plant practice probably does not show more than 80 per cent extraction on this small portion of the ore. No definite figure on this is available, as this particular ore is delivered at irregular intervals

Jan 1, 1939

By J. M. Morris

The point to be made most clear in this paper is the economic value of flotation in the Benguet mill flow sheet. It is rather a statement of effect with no attempt at a technical explanation of the cause. Certain well-known, easily understood reagents, mechanisms and principles have been adapted to the conditions at Benguet, and have proved to be more successful than was demonstrated in the laboratory. The mechanical and metallurgical development of this particular operation was arrived at by trial and error, with fortunately very little error. Changes were slow, of necessity, which in the end proved a blessing in that time was afforded for observation and analysis of the disturbing factors; and as a result each change was a definite step towards higher efficiency. Many of these steps were unpredictable from laboratory work because of the varied and differing characteristics of ores met with in daily operation of the mill, which were practically impossible to reproduce on a laboratory scale. The Benguet mill receives daily ores that differ as much as if they were delivered from three different properties. There is first the surface and upper-level zone, which produces an oxidized secondary ore containing considerable iron oxide, manganese oxide and some organic matter. Formerly, most of this ore consisted of very soft fill with some hard rock mixed in. It also contained an unusual amount of iron and aluminum sulfate, which formed hydrates upon entering the alkaline cyanide solution and caused excessive frothing. When flotation was introduced in the Benguet mill the general characteristics of this upper-level ore had changed considerably, in that it was practically all newly mined, fairly hard ore. It still contained many of the same disturbing elements, but was somewhat simpler to treat than formerly. The small proportion of fines is still troublesome in flotation, and plant practice probably does not show more than 80 per cent extraction on this small portion of the ore. No definite figure on this is available, as this particular ore is delivered at irregular intervals

Jan 1, 1939

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By E. G. Woodruff

(Butte Meeting, August, 1913.) FEW authors of treatises and papers on engineering subjects have . given adequate attention to topographic maps.. The statement applies especially to mining engineering in all branches. Even those who have discussed such maps have treated the subject only in a general way. Therefore it is proposed to outline in this paper a few of the uncommon, yet important relationships which topographic maps and their by-product, structure-contour maps, have to modern methods of mining investigation and development when the facts depicted on such maps are properly interpreted. Topography, as suggested by the etymology of the word, menus a detailed description of particular places. Written descriptions have been found less effective than the pictorial representations, therefore attempts have been made in various ways to picture the surface features of places. Lines and shading have been used, hachures drawn, and, finally, the contour topographic map. To a large extent this style of snap is the result of the demands of engineers. It is designed to meet their needs far more than those of the man untrained in engineering. In fact, the average man obtains a better idea of the topography of an area from the hachure system than from contour maps. . Since the maps. have been made chiefly for the use of the engineer, they ought to meet his demands on the one hand, and, on the other, should be used by him to the fullest extent. Such maps, when properly made, accurately portray a portion of the earth's surface and should present the topography better than a personal examination of the area without a map could present it, because the person making such examination views only a limited portion of the surface at a time, and estimates distances only roughly with his eye. Let the engineer consider carefully the fact that in many instances the topographic map is superior to a personal examination of the surface features of a property because the map is based on careful instrumental measurements, whereas the eye gives imperfect data because it can be used merely for the estimation and

Jan 6, 1913

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By Fred E. Beasley

Metallurgists have, in the last ten years, overcome many difficulties of high zinc in lead blast-furnace slags. This problem was brought to the front at the close of the war, by the price obtained for lead and the high cost of labor, fuel, and flux. The Port Pirie plant of the Broken Hill Associated Smelters, Australia, early in 1919 had increased the zinc oxide in its blast-furnace slags from 13.5 to 20 per cent., at the same time reducing the iron oxide in the slag from 33.5 to 25.6 per cent. These results were obtained by the addition of 10 to 12 per cent. granulated slag to the roaster charge, improved conditions of the crushing, mixing, and roasting of the constituents of the sinter. By experiments and improvements, the practice at this plant has developed a normal slag that carries 22 per cent. zinc oxide, and at times runs as high as 33 per cent. zinc oxide, with only slight furnace trouble. The granulated slag is used not only as a diluent to the sulfur in the roaster charge, but on account of its value as a slag-forming material and the physical properties it imparts to the finished sinter. The ore is mixed with flux and given a double roast. All the first roasting is by sintering with the Dwight & Lloyd machines. The final roasting is performed partly by Dwight & Lloyd machines and partly by H. & H. pots. The charge to the blast furnace consists chiefly of the final sinter, slag shells, siliceous and non-bearing sulfur lead ores. High blast and ore columns are the practice. The greatest care is taken to obtain in the final sinter as low a sulfur content as possible. Attracted by the success of the Port Pirie plant, The Consolidated Mining & Smelting Co. of Canada, at Trail, B. C., in 1920 treated its crushed primary sinter with about 15 per cent. granulated slag. The Trail smelter at this time was short of ore and a large part of the charge to the roasters consisted of the zinc-plant residue having the following analysis: 12 to 16 per cent. lead, 12 to 16 per cent. zinc, and 25 to 30 per cent. iron. The lead in the final sinter was low and the physical condition was so bad that all the sinter had to be screened before it could be charged to the blast furnace. Also it disintegrated on being trammed and dumped

Jan 1, 1925

By Leland L. Mink, Roy E. Williams, C. Daniel Kealy

The passage by Congress of Public Law 92-500 (the 1972 Water Pollution Control Act amendment) has placed a new emphasis on the need for methods to minimize the escape of water from tailings ponds. Presumably tailings pond seepage will fall under the jurisdiction of the act. This paper is designed to explain some of the problems caused by leakage from tailings ponds and to present a method by which leakage can be minimized if not eliminated. Ground-water pollution in one case studied by the authors results from leaching of old jig tailings that are intermixed with the upper part of a sand and gravel aquifer. Anomalous concentrations of zinc, lead, and cadmium occur in ground water and soil samples taken from the portion of the sand and gravel aquifer containing the old jig tailings. Analysis of water samples from a tailings pond located in the area indicates that the pond water is not the source of the heavy metal concentrations found in the down-gradient ground water. However, leakage from the pond and water from the pond's decant system combine with natural ground water to compound the problem by raising the water table into old jig tailings which cover the upper portion of the aquifer. The ground water which discharges from this aquifer causes a statistically significant decrease in the quality of the receiving stream water. The shallow ground water contains oxygen; therefore, corrective measures include lowering the water table to depths below the old jig tailings which cover the aquifer at ground level. This, in turn, implies elimination of ground-water recharge by subsurface leakage from the pond. A laboratory study and a mathematical model study have revealed that seepage from such ponds can be minimized by a carefully designed and managed peripheral tailings discharge system. The process involves maintaining the slime zone and the free-water surface near the center of the pond so that the slimes retard downward and semilateral movement of pond water. The free-water surface must not be allowed to extend out over the nonslime portion of the tailings during or after pond operation. Mathematical model output reveals that this method can hold the subsurface discharge rate to as little as 110 gpd per acre of pond water area. The technique should be applicable to any tailings pond system in which the loss via seepage of poor quality water must be minimized or where recharge of ground water by losses from a tailings pond must be minimized, regardless of the reason.

Jan 1, 1974

By John F. Blandy

Every new mining district has had its own peculiar experiences in inventing and experimenting upon new methods for the various operations of mining, and more particularly in the processes of crushing and dressing ores. As a matter of course, during this period many old things have been reinvented, patented, and cast aside, there to remain until at a future day other geniuses shall bring them forth again as new. In this respect the Copper Region of Michigan has not been behind other mining centres, and probably in no other part of the country has more money been expended in devising new machines and improvements upon old ones for the crushing of the rock. The appliances for washing the sand have not been so varied, simply for the reason that, having but one mineral, or rather metal, of high specific gravity to separate from rock material which varies but little in its character in any one mine, it requires much less care than is necessary in most mining centres of the world. At the beginning of operations in that district most of the work was in the control of Cornish miners, who introduced the simplest of Cornish mills, namely, wooden stem pestles, with wooden shafts and cams. These were well suited to the small mines, and particularly to the limited means of transporting more expensive machinery. As these facilities improved, they were enabled to change to iron, and to vary their patterns of rods, shafts, cams, and mortars. The most approved pattern, finally obtained, is the square or round stem, with collar adjustable by means of keys. In its present form it is a bar of cold rolled shafting, an eye in the top, an adjustable collar with key-plate and keys, the head and a shoe of chilled iron. The stem is fitted into the head by a slight taper. The battery has heretofore been of wood, lined with chilled cast plates, and bed-plate of the same, but within the past year the California pattern has been introduced. The screens are of sheet-steel, drilled with 16 holes to the inch. During this period of trial and gradual improvement in the pestle stamps, in the years 1855-6, the Ball steam-stamps were introduced, and after years of labor and expense, have been made the most efficient and powerful machines ever yet used for the purpose. It is ostensibly the Nasmyth steam-hammer, and yet the

By Linn Bradley, W. W. Strong, H. D. Egbert

Marked differences of opinion have been expressed by engineers interested in cleaning iron blast-furnace gases for use in hot-blast stoves and under boilers, in reference to the advantages of a hot-dry method over a cold-wet method. One point at issue involves the sensible heat energy in the moisture contained in the gas. Some advocates of the cold-wet methods claim that the condensation and resultant removal of the greater portion of this contained moisture by wet scrubbing, spraying or similar methods, results in a saving of some of this sensible heat energy, by reason of the fact that water vapor has a high capacity for sensible heat energy and may carry from the exit of a hot-blast stove, for example, more heat units than are sacrificed or lost when the gas is cleaned by this cold-wet method. Other advantages claimed for the latter method are: That gas burns more readily when it is free from moisture in any form; that because gas is made denser by cooling and removing the moisture it has a higher calorific value than hot gas carrying moisture; and that higher flame temperatures are obtained when the gas is cleaned by the cold-wet method. A search through the available literature fails to disclose any extensive calculations or records of conditions obtained in practice, bearing upon these phases of gas cleaning. This paper deals with these problems from the standpoint of the economy of using a gas of higher flame temperatures, of improved stove design, and of economy in the gas-cleaning department. Calculations have been made which show that by cleaning the gases by a cold-wet method the sensible heat energy of the blast-furnace gases is greatly reduced; and, in general, this loss of heat energy is far greater than that lost from the stoves or boilers due to the sensible heat capacity of the water vapor if carried away by the exit gases. By making use of the

Jan 1, 1917

By W. W. Schmittroth, A. Y. Bethune

THE commercial analysis of Special High-Grade zinc usually involves the determination of lead, iron, copper and cadmium as impurities in the base metal. Over the past 20 years, as the result of metallurgical improvements in the art of producing Special High-Grade zinc metal there has taken place a gradual exclusion of almost all extraneous elements, and the few that do remain in the final product have been virtually reduced to the vanishing point. Thousands of tons of zinc .are now commercially produced annually and made available to the trade, in which impurities are present only in the order of 0.0010 per cent or less and the sum total of all impurities does not exceed 0.0025 per cent. To such zinc the term "superpurity" might well be applied without undue exaggeration. The techniques used for production control and final analysis of Special High-Grade zinc by means of emission spectra in the laboratories of the electrolytic zinc plant of the Sullivan Mining Co. are based on the premise that self-electrodes are to be preferred over all other forms for the examination of the zinc in question. Furthermore, after a survey of the literature and considerable experimental work,1 it was decided that the spectrographic method of internal control, the principle of which was first announced by Gerlach,2 using a modification of the high-voltage alternating-current arc source introduced by Duffendack and Thompson,3 with the calibration of each photographic plate as recommended by Wolfe,4 would yield the most accurate and reproducible results. Self-electrodes were chosen in order to make use of one of the unique advantages inherent in spectrographic analysis; namely, the rapid and almost effortless detection of elements other than those being quantified by the analyst; or conversely, the proof that the zinc is free from such impurities if no spectral line of the suspected element appears. This fact was verified for certain elements, and will be discussed later. Carbon electrodes impregnated or packed with zinc salts chemically prepared from the zinc to be assayed were avoided for a number of reasons. First, the chemical manipulation was another time-consuming step, which increased the chances for contamination. Second, none of the common zinc salts, such as the chloride, nitrate or sulphate, yielded reproducible results under our conditions, nor did the spectral line of the impurity appear as readily in the low concentrations as when using zinc metal. Third, no commercial carbon, except the very expensive, was pure enough to use with this grade of zinc and the continued time, effort and expense incurred in the purification of carbon was not desirable. The use of Special High-Grade zinc self-electrodes introduces certain complications with regard to obtaining satisfactory excitation conditions, because it seems necessary to raise the temperature

Jan 1, 1946

By H. T. Matson, G. Allan Wallis

In the Northern Rhodesia copper fields the size of the orebodies and the exceptionally consistent values over great distances made it possible to outline the ore with drill holes spaced at 1000-ft. intervals; in some cases, 2000-ft. intervals. Owing to the fact that the size of the deposits made it very evident that much outside capital would have to be called in to develop them and, owing to the wide spacing of the holes, it was essential that the sampling of drill holes be as accurate as possible, so that outside examining engineers could adopt the results as trustworthy within the limits of accuracy of the drilling method. With this object in view, the field staffs of the Selection Trust group of companies have studied for the past three years, and are still studying, drill sampling in a very thorough manner, and for this reason it is felt that these notes may be of interest to engineers or students who are, or in the future may be, in charge of drilling operations. The orebodies in this field lie in shales and sandstones, more or less indurated, in the lower strata of the Roan series, and the copper mineralization is in the form of sulfides predominantly, with some oxidized copper minerals. These interested in the geology and history of the area can find full details in a recent paper by Anton Gray and Russell J. Parker.' In some formations core recovery was good—between 90 and 100 per cent.—and where any difficulty occurred in recovering sludge, as in fissured ground, this was not insisted upon; but the samplers' difficulties, both practical and theoretical, do not commence until core recovery drops and sludge recovery becomes important, for if core is being ground up it is recoverable only as sludge, and naturally the sludge sample, which theoretically should contain only the material cut from the annular ring around the core, is being salted, in a sense, by the ground-up core. In the perfect core, where 100 per cent. core is recovered as well as 100 per cent. sludge, the two samples can be treated separately, as in the case

Jan 1, 1931

"It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time 'and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. The members of the Charles F. Rand Foundation Award Committee, of which J. V. W. Reynders is Chairman, are listed on page 12. In both 1938 and 1939, the Committee gave consideration to the question of choosing a medalist but in each year the decision was reached to give financial help to other projects as an alternative. In 1938, publication of a monograph on "Struc¬ture of Ore Deposits in the Continen¬tal Framework" and of a booklet en¬titled "The Call for Endowment" was financed; and in 1939, a special appro¬priation was made to defray the ex¬ penses of special speakers for Affiliated Student Societies of the Institute. In 1940, the Committee elected to nominate a candidate for the medal and unanimously selected Robert, Crooks Stanley, Chairman of the Board of the International Nickel Co. This recom¬mendation was approved by the Board of Directors and Mr. Stanley became the first recipient of the medal. Citation for Award to Robert Crook,, Stanley. "For His Pioneering Leadership During a Period of Active Growth and Development of a World-wide Enterprise Involving the Mining of Nickel Ores, the Metallurgical Treatment Thereof, and the Expansion and Diversification of World Markets for Nickel Products. "For His- Able Direction of the Corporation Encompassing These Activities, Which Has Established an Enviable Record in Its Relations With Employees. Stockholders and With the Public."

Jan 1, 1941

By J. R. Dawson, J. A. Glunt

Vesta No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin's by-product coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War II, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out.

Dec 1, 1956

By Ernest Klepetko

A NOTABLE amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: [Specific gravity (melted) 1.03 -1. o6 Acid number6-8 Softening point, mercury method 160 -165°C Iodine value (Wijs)140-1.50 Refractive index1.544 Color (Hellige, 25 pct toluol) ...14 Molecular weight, average732 Purity, 99 + pct pure hydrocar Bon] "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility. The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration engineer for Combined Metals Reduction Co., obtained U. S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1947

By R. B. Moore

Page History................................ 708 What is Radioactivity?........................ 710 Disintegration Series.......................... 711 Radium Ore Deposits......................... 713 Metallurgical Treatment........................ 717 Methods of Ore Concentration..................... 722 Future Supply of Ore......................... 723 Uses of Radium............................ 723 Mesothorium as a Substitute for Radium................. 724 Discussion.............................. 725 Probably no other metal excites as much interest, among both scientific men and the general public, as radium. This is due partly to the high cost of radium salts and partly to the peculiar properties of the element. Since radium-bearing ores were discovered in the United States, the interest of American scientific men has been stimulated and, at the present time, more radium is extracted and refined in this country than in all the rest of the world together. HISTORY The property of radioactivity was discovered, partly by accident, by Henri Becquerel, the French physicist, in 1896. He was experimenting with certain fluorescent substances in order to find, if possible, a connection between fluorescence and the recently discovered X-rays. Among other chemicals which possess the property of fluorescence, he was using salts of uranium. His custom was to expose the fluorescent substance to the action of sunlight and then register the effect of possible penetrating radiation on a photographic plate protected from ordinary light. Bec-querel's experiments gave positive results at once, and he at first believed that he had discovered a relation between fluorescence and X-rays. Later he exposed a plate to a uranium salt which had not been previously exposed to sunlight. To his surprise, on developing this plate, he found that he had obtained the same effect as he had previously secured when

Jan 1, 1919

By Edgar Shepard

THE interest of the Federal Government in improvement of water-ways dates from 1820, when Congress appropriated $5000 for making a survey of the Mississippi and Ohio Rivers and assigned this work to the Corps of Engineers of the Army. Since that time the Government has gradually assumed increasing jurisdiction in the matter of improvement and control of inland waterways until, by the River and Harbor Act of Jan. 21, 1927, Congress assigned to the Secretary of War and to the Chief of Engineers the duty of making surveys, in accordance with House Document No. 308, 69th Congress, to formulate plans for the most effective improvement of the navigable streams of the United States and their tributaries, for navigation, development of water power, control of floods, and the needs of irrigation. Virtually all the preliminary investi-gations and surveys required by this act have been completed. The reports made to Congress have been published and often are referred to as "308 Reports." The map shown in Fig. 1 is merely a skeleton distribution of the projects covered by these reports, but it serves to indicate the magnitude of the proposed undertaking. In many instances, a single character on the map stands for a major development involving several dams and reservoirs or many miles of canals or levees. The devastating floods of 1936, and the need for worthy public works to take up the slack in employment, gave further impetus to this program and in 1936 led to the enactment of a bill authorizing a large number of these projects.

Jan 1, 1940

By E. T. Dumble

In the Bosquejo Geoldgico de Mexico, published in 1897 by the Secretaria de Fomento as Nos. 4, 5 and 6 of the Boletin del Institute Geologico de Mexico, the Director, Jose C. Aguilera, after a detailed account of the geological observations made by himself and his assistants on their several trips through the various districts of the Republic, gives in Part 2 a synopsis of the geology of Mexico, describing . al1 the formations recognized, the rocks comprised in them, their geographical distribution, disturbances, principal eruptions and economic features, as explanatory of the Geological Map of Mexico. In Part 3 Prof. Ordonez describes many of the interesting eruptive rocks of Mexico." This work brings together in a very satisfactory way about all of the published results of geological investigations in Mexico; and although the determinations of the authors with reference to some of the sedimentary deposits are very different from those of other writers, they seem to be based upon good paleontological grounds in each instance. From the map and the text of this paper it appears that the condition of knowledge in regard to the geology of the State of Sonora, at the time of its publication, was about as follows: The western portion of the State, lying between the coast line of the Gulf of California and the foot-hills of the Sierra Madre mountains, is largely Quaternary, interrupted by areas of Azoic rocks and of later eruptives, with two or three limited exposures of limestones of the Cretaceous; while the eastern or

Jan 1, 1900

By J. C. Konopka, S. A. G. Poppen, E. K. Roesner

Many shafts have experienced stability problems during shaft sinking because the designer failed to fully appreciate the conditions he would encounter. Some shafts have failed during construction because the ground supports provided to compensate for the expected conditions were inadequate despite the most careful investigations and analyses. To design a ground support which is ultimately safe to achieve stability during shaft sinking would be too costly and impractical and, therefore, many shafts would simply not be constructed. The design of a ground support for shaft sinking based on an intimate understanding of the expected ground behaviour and stress development during excavation combines the art of mining with the science of geotechnical engineering. Where no historical design data is available, the designer of the ground support must: 1. classify the rocks and soils and assess their behavioural characteristics; 2. calculate the primary and secondary stresses; 3. design and/or select a ground support system which will ensure stability of the excavation during shaft sinking.

Jan 1, 1983

By Fred J. Wright

Originally, mining machines were actuated by purely mechanical mechanisms comprising cams, levers and gear trains, which became more and more complex as demands were made for additional operations that would increase mine tonnage. To simplify these intricate machines, development engineers began utilizing the principles of high-pressure hydraulics long employed for the control of various machine tools. The resulting specificially developed hydraulic systems are. now literally the heart of the mining machine. During world war NO. 2, very little fundamental change in design was made in existing mining machines, but because of the recognition of the merits of hydraulic application to the machines of war, it is reasonably certain that hydraulics will be applied to mining machines in the future to a much greater extent. This potential future indicates that a more thorough knowledge of hydraulics and its maintenance must be incorporated in mine operation. Maintenance of high-pressure hydraulic equipment varies considerably with respect to mine practice and conditions. The success or failure is largely dependent upon the hydraulic fluid and its care. Since all successful hydraulic systems have been designed around the use of mineral oil as the fluid, a complete analysis of this prime factor should be made to make clear the requirements of the fluid in a hydraulic system. Contamination of Oil Manufacturers of mining machinery usually have specified an S.A.E. rating or viscosity index of the proper mineral oil for use with their respective machines without considering the fact that many oils will meet these specifications but will not give the desired life or efficient operation. Hydraulic fluid should be specified as a good grade of mineral oil, such as turbine oil, having rust and oxidation resistance. It must have high chemical stability, high lubricity, and proper viscosity. These factors will minimize maintenance costs by reducing wear and the consequent replacement of parts, and at the Same time will lower costs for the oil by extending its life. Rulk purchases of oil should be limited to small sealed containers provided with a Proper pouring spout, thus reducing the possibility of contamination of the oil before it reaches the mining machine. The introduction of foreign matter, such as sand, water, coal dust and residue oil left in filling containers, will cause untold damage and maintenance expense. Sand, being one of the best natural abrasives1 will soon wear the close tolerances of the various hydraulic mechanisms to an extent that will necessitate complete replacement. Water is considered normally insoluble in oil, but because of the churning action of a hydraulic system water is broken down to particles so small that they remain in suspension. This suspension is known as

Jan 1, 1947