Search Documents

By J. Leja, J. H. Schulman

FROTH flotation is usually effected by the addition of a collector agent and a frothing agent to an aqueous suspension of suitably comminuted mineral ores. The action of collectors is to adsorb onto the surfaces of minerals to be separated, sensitizing them to bubble adherence. The action of frothers has, in the past, been accepted as that of froth formation only, brought about by a lowering of the air/water interfacial tension. Substances capable of producing froth are classed1a,b according to their relative capacities for production of froth-volume and froth stability in the simple frother-water system. The purpose of this paper is to show that the surface active agents acting as frothers become effective only when there is a suitable degree of molecular interaction taking place between collector molecules and frother molecules at the air/water and solid/ water interfaces. Further, the discussion will demonstrate that the actual mechanism of adherence of an air bubble to a suitably collector-coated particle is due to the molecular interaction collector-frother. This leads to the formation of a continuous interfacial film of associated molecules, anchored to the mineral by polar groups of the collector, and enveloping the whole bubble. The tenacity of adhesion mineral-to-bubble results from the strength and the visco-elasticity of this mixed film.

Jan 2, 1954

By E. W. Schilling

THE separation of hematite by hysteretic repulsion was first brought to the attention of the public in 1922, by W. M. Mordey1. Three years later another paper2 was published and after another four years a third paper3 appeared in the South African publications. Certain data were lacking in these papers. In order to continue the work intelligently a knowledge of the shapes of the hysteresis curves for certain minerals was very necessary. This information was not available until the present year4. It was known that reduction of certain ores rendered them amenable to this process of separation but definite data in the form of curves showing exactly the effect of such treatment were lacking. Prob-ably our best source of information on the separation of minerals by the use of alternating-current magnetic fields today is the reports from the U. S. Bureau of Mines 5-7. It is not the purpose of this paper to tell the reader in detail how to make a commercial separator. Experimental models have recently been made 7 and the results obtained have been so good that it is the opinion of the authors that the public will soon take an active interest in the subject and its development. The writers have constructed a separator that is considerably different in construction and operation from the two types described by Mr. Davis. This will be described, but the real purpose of this paper is to outline certain experiments and give curves showing data that have a fundamental bearing upon the practical construction of a separator of this type.

Jan 1, 1935

By Graham Bright

METAL mines were developed long before coal mines and the early lighting of underground workings was effected by torches and candles. The early coal mines were outcrop workings and little trouble was experienced from gas, but as the mines became deeper and shaft mines were opened it became apparent that an open-flame lamp was exceed-ingly dangerous where gas occurred. No satisfactory way of lighting gaseous coal mines was found until Sir Humphrey Davy brought out his famous safety lamp in 1815. The introduction of the Davy lamp was a great step forward but it was unsatisfactory from a light standpoint because the gauze absorbed a large percentage of the light given out by the flame. Clanny corrected this by the introduction of a cylindrical glass lens, which not only per-mitted a free distribution of the light from the flame but added greatly to the safety by eliminating the possibility of the flame coming in contact with the gauze and by protecting the flame against air currents. A very complete story of the flame safety lamp since its inception is given in the U. S. Bureau of Mines Bulletin No. 227, by J. W. Paul, L. C. Ilsley and E. J. Gleim, published in 1924. A little more recent publication, known as Safety in Mines Research Board Paper No. 4, entitled "The Light Power of Flame Safety Lamps," by R. V. Wheeler and D. W. Woodhead, was published in England in 1927. The flame safety lamp was the-only lamp available for gaseous mines for about 100 years. Although the incandescent electric lamp has been in use over 50 years, it was not found safe to use this lamp from wired circuits in gaseous locations. The storage battery was advocated shortly after the develop-ment of the incandescent lamp but until the introduction of the tungsten filament in the miniature mine-lamp bulb, the battery lamp was not a real possibility because of the excessive weight of the battery necessary to produce a sufficient amount of light. The actual development of the electric-battery type of lamp took place largely between 1910 and 1915. In England and Europe, the development was almost entirely along the

Jan 1, 1935

By H. S. Munroe

The native copper of Lake Superior occurs in the form of fine grains and scales, disseminated in small percentage through the copper-bearing rock ; and in large and small masses, from a few pounds to several hundred tons in weight. Formerly the bulk of the copper came from the mines of Ontonagon and Keweenaw counties, producing mass copper. At present these mines furnish less than one-tenth of the total product, and fully one-half of this is from a single mine. The masses are usually found irregularly distributed in nearly vertical fissure veins, and require much dead work; in sinking, drifting, and stoping for their development. The risk and expense attending the working of these mines have made them, with few exceptions, anything but profitable.

Jan 1, 1880

By Robert I. Jaffee, Bruce W. Gonser

RECENT work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C. and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. MATERIALS AND ALLOYING As in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni, and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about 1050°C., and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. THERMAL ANALYSIS In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,1 a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946

By T. L. Joseph

THE United States Bureau of Mines has been studying the blast-furnace process for, about ten years. An experimental furnace was developed by the bureau in cooperation with the Minnesota School of Mines Experiment Station, University of Minnesota. Many data have been obtained and published.1 Royster, Joseph and Kinney§(48) found that the particle size of ore had an important effect upon the blast-furnace, process. Kinney(28) stated: Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft, the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of the stock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and the gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. It is obvious that fine ore particles occurring in the ore as charged, or . formed in the furnace due to heat and mechanical action, place a definite limitation upon the efficiency of the operation. There is also an economic loss of fine material as dust.

Jan 1, 1930

INTRODUCTION TO STATISTICAL INFERENCE The intent of the mineral appraiser in collecting samples from a mineral deposit is to arrive at accurate conclusions concerning the size and value of the deposit. In other words, he wants to derive reliable inferences about the total mineral population from the collected sample data, which (he hopes) is representative of the whole. The discussion of sampling theory in Chapter 2 was oriented toward assuring that our sampling techniques and sampling units would indeed be representative of the total mineral population. Chapter 3 described the most common statistical parameters for defining distribution in various populations. Chapter 4 gave some insight into theoretical distributions of random variables and the probabilities associated with them. The intent of this chapter is to derive inferences from the preceding information about the population mean and the population variance. Knowing something about the normal distribution, and assuming our samples represent a roughly normal population, we can make inferences or logical deductions about the estimated interval or the limits of values which can be assigned to a mineral population. ESTIMATION OF POPULATION PARAMETERS In the application of statistics to mineral deposits it is never possible to know the actual values of the parameters or the theoretical distribution of values within the deposit for which our data are samples. Even after the deposit has been mined out it is questionable if the true value of the parameters can be retrieved accurately, due to dilution, mining, and processing losses. Therefore, our problem is to determine what function of our sample values we should use to estimate the unknown parameters of greatest interest to us-namely, the population mean and the population variance of the deposit. Since we cannot know

Jan 1, 1980

By R. L. Wilcox, M. L. Fuller

MOST commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper2 of this series, and in this paper, aging phase changes of zinc alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evaluated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0.03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change,

Jan 1, 1935

By Henry D. Hibbard

A noted ordnance engineer once said to a friend, in speaking of the production of great steel guns, " How is it ? We design our guns with a factor of safety of eight, and the guns burst." The vague way in which internal stresses and strains in iron and steel are often considered and spoken of makes it worth while to examine them, as to their nature, their causes and results, how they may, for useful purposes, be advantageously dealt with, and how, when detrimental or dangerous, they may be reduced or kept within harmless proportions. Rankine defines " strain " as a change of form or dimensions of a solid or liquid mass produced by a stress. This definition seems intended not to cover strains due to internal stresses, and it will help us in the present inquiry to consider strain as a tendency to change as well as an actual change of form. Internal strains in iron and steel are the result of stresses within the mass of the piece, some parts pulling and others pushing in resistance to them; or, in other words, some parts are in tension and some in compression, each part striving to relieve itself from strain and make the piece assume a form in which all parts are at rest. Subdivision, so that each part could relieve its strain by motion relative to the other parts, would, if carried out far enough, practically obliterate strain. The internal strains we are now to consider are not those due to the stresses of the service which the piece is rendering, either alone or as a part of a structure, which may be termed service-strains, but those which originate or at least are contained in the piece itself. Internal stresses in a piece of metal are, like action and reaction, always equal and in opposite directions. The stresses

Jan 1, 1907

By James E. Jopling

The county of Marquette, Michigan, includes nearly all the iron-mines that have been worked on the Marquette range, which stretches in a generally western direction from the mines at Negaunee, 10 miles from Lake Superior, to those beyond Michigamme, some thirty miles further. The geographical position of this range, nearer to eastern ports than the other iron-ranges, and its ready access from the lake, gave it for a long time a controlling advantage. The country in which the mines are situated is from 800 to 1000 feet above the level of the lake, and is for the most part broken by steep hills, which rise from 100 to 200 feet; between these the land is rolling or

Jan 1, 1898

By E. Stansfield, J. W. Sutherland

It is well known that the ash left when coal is burned is not the same either in chemical composition or in weight as the mineral matter originally present in the coal. This mineral matter has been referred to as "mineral impurity," "ash-forming constituents" and "corrected ash." The authors prefer the simple name used in the title and throughout this paper. The mineral matter in a sample of coal cannot be isolated unchanged and then weighed; but if the relation between the weight of mineral matter in the coal and the weight of ash remaining when the coal is burned can be ascertained, the weight of mineral matter in the sample can be calculated from the determined weight of ash. When the weight of mineral matter in the sample is known, the weight of pure coal can be found by subtraction. This pure coal must be the basis of accurate coal classification. W. F. Wheeler,l,3 W. Brinsmaid,2 S. W. Parr, and many subsequent workers have studied the relation between mineral matter and ash. Wheeler and Parr and others have deduced formulas for calculating this ratio, and used heavy-solution separations for checking the accuracy of their formulas. Brinsmaid hand-picked and analyzed two separate samples (and mixtures of these) and based thereon a graphical method of deducing the ratio. In the Fuel Testing Laboratories of the Scientific and Industrial Research Council of Alberta, a graphical method, based on heavy-solution fractionation of coal samples, has been used with marked success for the past 7¼ years for determining the mineral matter-ash ratio. This method resembles that employed by Brinsmaid in 1907.

Jan 1, 1930

By Pol Duwez, Ellis P. Frink, Paul Pietrokowsky

Ti-Au alloys in the composition interval 0 to 66 213 atomic pct Au have been studied over a temperature range from 400° to 1500°C. A partial phase diagram has been established from micrographic and macroscopic observations. All intermediate phases, Ti3Au, TiAu, and TiAu., exhibit open melting maxima. It has been observed that small additions of gold lower the allotropic transformation temperature of titanium. The P solid solution decomposes eutectoidally to a solid solution plus Ti3Au. The solubility of gold in a solid solution decreases with temperature. THERE have been several papers in the literature pertaining to the alloy system Ti-Au. However, a comprehensive study of this interesting constitu- tion diagram has not been conducted. Previous investigations have been concerned with the crystal structure of intermediate phases or partial phase diagrams. This paper represents a partial constitution diagram, Ti-TiAu,, the first portion of an investigation of the entire binary system. Laves and Wallbaum' reported the intermediate phase Ti,Au to be isomorphous with CuAu, L12 type. In a more recent paper, Duwez and Jordan' have concluded that TiAu has an atomic arrangement which is related to Cr,Si. The intermediate phase

Jan 1, 1957

By C. L. Dake

Residual deposits occur both as products of weathering and as products of hydrothermal decay. Products of Weathering That climatic conditions affect greatly both the rate and the results of weathering, is shown in temperate, polar, arid, and tropical regions, each of which will be considered separately. Weathering under Temperate Climates The decomposition of any rock is accomplished by the removal of the more soluble bases, and a concentration of the relatively insoluble oxides of iron, aluminum, and silicon. By reason of its somewhat greater solubility, silica is much more subject to removal than iron and alumina. The two important residual end products of weathering are sands and clays, the former consisting essentially of quartz, and the latter of kaolin and limonite.l When such deposits are formed in situ, the sands and clays are not separated, but remain as mixtures, which can be more or less perfectly separated by treatment with water. In such a separation, the ferric oxide or hydrate tends, by reason of its fine state of division, to remain with the clays and silts rather than the sands. While ferruginous sandstones are everywhere common, they are rarely rich enough in iron to become an ore without secondary concentration. Since the silica of these sandstones is completely crystalline quartz, it is much less liable to removal by solution than are the more soluble forms of partly amorphous chert and jasper, which have been removed on so large a scale from the Lake Superior iron formations.2 Moreover, the iron cement of sandstones, which constitutes the chief iron content of these rocks, is often a result of later infiltration, and not of original sedimentation. Thus if clays rather than sands contain the iron of residual decay,

Jan 1, 1916

By William Reynolds

This paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. Face Preparation When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of completeness to which these impurities arc removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miller is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation. Many mines with one or more bands of impurities in their seams are able to mine a desirable product with a comparatively small amount of surface preparation. In fact, three companies in West Virginia have recently changed their methods of fact* preparation, with most gratifying results. The first company (in the Kanawha field) after changing its cutting practice with the hope of relieving a sales problem, was rewarded by an approximate 3 per cent drop in ash in the product. Another company, operating in the same field, reduced its ash approximately 4 per cent by a change in cutting practice. The third company (in the Pocahontas field) found the wet washer inadequate in producing a marketable coal, and installed new cutting machines. Three cuts are now being made in each working place, and the results arc so satisfactory that the cleaning plant has been abandoned.

Jan 1, 1938

By William Reynolds

This paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. Face Preparation When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of completeness to which these impurities arc removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miller is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation. Many mines with one or more bands of impurities in their seams are able to mine a desirable product with a comparatively small amount of surface preparation. In fact, three companies in West Virginia have recently changed their methods of fact* preparation, with most gratifying results. The first company (in the Kanawha field) after changing its cutting practice with the hope of relieving a sales problem, was rewarded by an approximate 3 per cent drop in ash in the product. Another company, operating in the same field, reduced its ash approximately 4 per cent by a change in cutting practice. The third company (in the Pocahontas field) found the wet washer inadequate in producing a marketable coal, and installed new cutting machines. Three cuts are now being made in each working place, and the results arc so satisfactory that the cleaning plant has been abandoned.

Jan 1, 1938

By Fred T. Agthe, Fred C. Bond

When some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material. and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media during normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many commercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an important one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain laboratory tests were made from which it was found that different materials form coatings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qualities, like coal and graphite. In general, the softer materials tend to coat at coarser sizes than the harder or more brittle materials. Limestone, as an example, will coat more readily than quartz, even though limestones of different- texture and composition exhibit great differences in coating potentialities. Various materials were tested in the laboratory to show the variation in coating qualities. It was found that in most tests quartz must be ground to a fineness that would permit it to pass through 325 mesh before coating became markedly detrimental to the grinding operation. Siliceous rocks, however, tend to coat more readily than quartz. Granite, which is composed essentially of feldspar, quartz and mica, has been found to start coating at about 92 per cent through 200 mesh, and feld-spathic minerals alone usually show a tendency to coat at the same fineness. Barite has been ground in the laboratory to a fineness of 99 per cent through 325 mesh without showing serious coating of the grinding media. Gypsum coats readily. Apatite and phosphate rock usually tend to coat. Hematite usually coats, although when mixed with charcoal it does not do so. In testing the carbonate rocks and minerals, it has been found that burned magnesite, dolomite, and dolomitic limestone coat, whereas calcite and calcined calcite do not coat so readily. It has been found that commercial glass, slate, talc, steatite and coke have little tendency to coat. The relative tendencies toward coating during grinding operations, exemplified by

Jan 1, 1943

By Fred C. Bond, Fred T. Agthe

When some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material. and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media during normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many commercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an important one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain laboratory tests were made from which it was found that different materials form coatings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qualities, like coal and graphite. In general, the softer materials tend to coat at coarser sizes than the harder or more brittle materials. Limestone, as an example, will coat more readily than quartz, even though limestones of different- texture and composition exhibit great differences in coating potentialities. Various materials were tested in the laboratory to show the variation in coating qualities. It was found that in most tests quartz must be ground to a fineness that would permit it to pass through 325 mesh before coating became markedly detrimental to the grinding operation. Siliceous rocks, however, tend to coat more readily than quartz. Granite, which is composed essentially of feldspar, quartz and mica, has been found to start coating at about 92 per cent through 200 mesh, and feld-spathic minerals alone usually show a tendency to coat at the same fineness. Barite has been ground in the laboratory to a fineness of 99 per cent through 325 mesh without showing serious coating of the grinding media. Gypsum coats readily. Apatite and phosphate rock usually tend to coat. Hematite usually coats, although when mixed with charcoal it does not do so. In testing the carbonate rocks and minerals, it has been found that burned magnesite, dolomite, and dolomitic limestone coat, whereas calcite and calcined calcite do not coat so readily. It has been found that commercial glass, slate, talc, steatite and coke have little tendency to coat. The relative tendencies toward coating during grinding operations, exemplified by

Jan 1, 1943

By W. W. Smeltzer

The linear formation rates of wustite films have been determined over the temperature range 590° to 1030°C using a vacuum microbalance technique. These rates are dependent directly on the partial pressure of carbon dioxide, Activation energies for film and scale formation in carbon dioxide and oxygen atmospheres are equivalent to either the dissociation energies of carbon dioxide and oxygen, or the activation energy for the diffusion of cation vacancies in wustite. Of the metals, iron is the most widely used basic constituent of durable alloys despite its intrinsic property of converting at a relatively rapid rate to the oxides from which it is derived. This property has accounted partially for many investigations on the oxidation of iron at low and high temperatures. Interpretation of the results have been complicated by formation of multilayers containing the various oxide phases. To aid in elucidation of the oxidation kinetics, measurements have been carried out in this investigation on the growth of the wustite surface layer. There are several studies directly related to the objective of this investigation. The growth of multilayer scales has been demonstrated to be diffusion controlled in oxygen at atmospheric pressure over the temperature range 450" to 1200°C by Davies, Simnad, and Birchenall.' To gain an insight into the diffusion mechanism, Himmel, Mehl, and ~irchenall' determined the self-diffusion coefficients of iron in wustite, magnetite, and hematite. These results were used to evaluate the oxidation rates of iron and its oxides, taking as a basis the theoretical parabolic rate equation developed by Wagner., The evaluations were compared to experimental data and were shown to provide essential confirmation of this theory. Fischbeck, Neundeubel, and salzer4 have demonstrated that the oxidation of iron in carbon dioxide and other atmospheres at high temperature obeys a linear relationship. Because the Arrhenius temperature coefficients of the reaction rate constants changed at the A, point they concluded that the passage of iron into the oxide controlled the reaction. This viewpoint has been accepted by Benard and ~albot' to explain the occurrence of linear rates in oxygen before the onset of diffusion-controlled parabolic oxidation. This basic premise of a rate-controlling reaction at the iron/oxide interface has been questioned recently by Hauffe and Pfeiffer.' Since the formation of wustite may follow a linear or parabolic relationship depending on the pressure of the gaseous re-actant, they propose that linear oxidation is determined by a chemisorption reaction while parabolic oxidation is controlled by diffusion. As confirmation of this viewpoint, Hauffe and pfeiffer6 and Pfeiffer and ~aubmeyer' have established that the linear scaling constants of wustite formation at 1000°C in carbon-dioxide or low-pressure oxygen atmospheres

Jan 1, 1961

By R. J. Teitel

FOUR or five years ago an investigation was initiated to study and develop basic information on llquid metal fuels for future power nuclear reactors. The objective was to find fluid forms of uranium (solutions or dispersions) in low melting alloys. A summary of the different fuels was presented in a recent article by Teitel, Gurinsky, and Bryner.' The combination of uranium and bismuth, with its low thermal neutron cross section and low melting point, is of basic interest to the development of these fuels. Most of the previous effort on the U-Bi phase diagram was done under security regulation. Ahmann and Baldwin' reported their findings on the U-Bi system in 1945. Their results indicated that the phase diagram had at least two compounds and possibly one more. UBi, and UBi were established by chemical analyses of residues after high temperature centrifugation of alloys. UBi, decomposed peritectically at1980°C and there were signs of another reaction above that. UBi melted at a very high temperature, and there were also signs of a monotectic at high temperatures in high uranium alloys. The solubility of uranium in liquid bismuth has received attention by three groups of authors: Bareis,X ayes and Gordon,' and Ahmann and Baldwin.' The latest and most widely accepted data is that of Bareis, and it is included in Fig. 1 along with new data at higher temperatures. Brewer et al." and Ferro"'' have used X-ray diffraction to determine the number and crystal structure of the compounds. Brewer identified the structure of UBi to be a simple NaCl cubic structure having a cell edge of 6.364A. The density of the compound was calculated to be 11.52 g per cu cm. Two other unindexed patterns were presented as possibly belonging to two other compounds. Ferro agreed with Brewer on the crystal structure of UBi and identified the structure of UBi, and U,Bi,. The intermetallic compound UBi, has a tetragonal cell with a = 4.445A and c = 8.908A. The density of the compound was determined and the number of atoms per cell (six atoms) was calculated. The X-ray density reported was 12.35 g per cu cm. The compound UsBir was treated in a similar way and it was reported to have a cubic structure 9.35A on an edge and to contain 28 atoms per cell. The density was given as 12.59 g per cu cm. Teitel reported that there was a compound UaBi, and no UBi, compound. (The difference in the compositions is 3.3 pct U.) This conclusion was based upon the extrapolation of some 20 tie lines in the

Jan 1, 1958

By J. A. Woolf, E. S. Leaver

THE purpose of this paper is to describe, in a general way, gold-dredging operations in California, with particular reference to unusual features, including types of deposits and recent attempts to improve the recovery of the gold. Dredging Areas The gold-bearing formations that traversed the western slope of the Sierra Nevadas for a north and south distance of some 300 miles furnished the immediate source of the gold found in most of the placer deposits of California. Erosion through a long period carried the gold, together with various forms of partly disintegrated material, to lower elevations and formed placer deposits. Through the classifying action of water in motion, the coarser gold and heavier material of various kinds were - deposited relatively near the source; consequently, in the higher mountain country, old river channels were worked feverishly during the early California gold-rush days because of their high gold content. With the working out of these known high-grade channels, and from the knowledge thus obtained of prehistoric stream beds, drift mining was started and flourished until about 1890. Even today many drift mines are operating with the objective of opening other old Tertiary river channels that have been covered by volcanic flows. Adjacent to these areas, which contained relatively high gold values in the older river channels, smaller particles of gold, gravel, and debris were deposited along the sides of the former stream beds and on the adjoining flat areas, thus forming the large placer deposits, which were worked principally by hydraulic mining. Following the course of the ancient rivers and of the present drainage system to the lower edge of the foothill country, extensive areas of alluvial

Jan 1, 1937