Search Documents

C. G. Dunn (Generai! Electric Research Laboratory)— The author is to be commended on his attempt to calculate the residual strain energy from information on the dislocation density within the subgrains and a surface energy associated with the subgrains. However, much closer agreement between a calculated critical size of a nucleus and the observed size of grains that did not continue growing can be obtained if a reasonable correction is made in obtaining the energy of the surfaces of the subgrains. For example, since the sample is a single crystal with a cold-rolling reduction of 70 pct in thickness, one needs either an average disorientation for this or an average subgrain boundary energy rather than the 2.5 deg disorientation of a bent crystal, which was used by the author. From either the Laue photographs of the author or the pole density plot of Koh and Dunn 16 for a (113) [332] cold-rolled crystal the

Jan 1, 1961

By Arthur Phillips

DURING the past few years considerable interest has been shown in the study of fiber, and its effect, in wrought metals. Fiber has recently been defined as a "condition of parallelism of important lines or details in the structure. "1 Briefly stated, two distinct types of fiber are commonly encountered. One results from the alignment in the direction of working of constituents, more or less segregated, such as slag, oxides, carbides and dendritic formations. The second, and least understood, type is produced by working the metal below the recrystallization temperature in such a way as to develop a parallelism of the grains. This condition is readily recognized by the pronounced elongation of the grains in the direction of working. Under certain deformational treatments the grain fragments produced by cold working tend to orient in certain definite directions with respect to the axis of extension. Furthermore, even in metals that have been annealed after cold working preferred orientations may be present. It is perhaps logical to assume that such marked parallelism of structural elements would be manifested by directional properties in the metal. As a matter of fact, tests on many kinds of materials have shown differences in varying degrees. In recognition of this condition, propel design, for many purposes, places the fiber axis in such a way as to present the direction of maximum strength to the greatest applied stress.

Jan 1, 1931

By J. L. Byers

THE metals of the platinum group, ruthenium, rhodium, palladium, osmium, iridium and platinum, have certain characteristic effects on the structure and appearance of the cupellation bead. These effects are dependent not only on the particular member of the group present, but also on its concentration. The extent and quality of these effects, however, have not received investigation worthy of their importance. Bannister and Patching investigated the qualitative effects of some of these metals in 1913. This paper deals with a possible rapid qualitative and quantitative delineation of the effects exerted on the cupellation bead by the various metals in the platinum group. More particularly, the paper correlates quantitatively the presence of such metals with their characteristic structural and surface effects. Inasmuch as the various members of the group are more frequently associated with gold than with silver, the gold button will receive the greater consideration. The past two decades have seen a much greater interest manifested in this particular group of metals, because of the increased industrial demand for them. There has been a constantly growing need for assays that will not only express the silver and gold values but also indicate the presence of the other metals. If these indications could be used as quantitative criteria, their value would be greatly increased, because the methods of chemical analysis for the elements of the platinum group are lengthy, involved and unreliable except when the analysis is made by an expert and experienced rare-metal analyst. The materials for the X-ray diffraction examination of the different beads were prepared by filing and screening to -200 mesh, and were then rayed in a General Electric X-ray diffraction unit. The filed samples were treated magnetically in order to eliminate any possible steel particles. Sodium chloride and C.P. gold and silver were used as standard comparators.2 (See Table 1.)

Jan 1, 1932

By Eric Sinkinson

MANY of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally enclosed in-serpen-tine masses, somewhat decomposed, and in mining it wall rock is inci-dentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumna, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18° C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact; MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18° C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H20) or (4MgCO3.Mg(OH)25H20), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2. The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates. The range in published figures for solubility

Jan 1, 1936

By James S. Browning

The Bureau of Mines conducted laboratory and small-scale continuous tests of kyanite ore from Georgia and South Carolina to determine the technical feasibility of recovering commercial grade kyanite concentrates by flotation. The research indicated that combinations if sulfuric acid and petroleum sulfonate may be used effectively for flotation of kyanite from quartzite-kyanite ore. This report summarizes the results of these tests, and demonstrates the feasibility of producing commercial-grade concentrates with a high recovery of the contained kyanite. Extensive deposits of kyanite occur in the southeastern United States. The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate for many years at the present rate of consumption. According to Espenshade and Potter,' the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30% kyanite. The tonnage of kyanite-bearing gneiss and schist is much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina-South Carolina, and at Graves Mountain, Ga. Of the known deposits, only four were being mined for kyanite in 1 967. These deposits are near Farmville and Dillwyn, Va., Clover, S.C., and Washington, Ga.

Jan 1, 1970

By John Wulff, R. Buehl, H. Hollomon

Although the main features of the transformations occurring in 18-8 have been published already, certain conclusions merit questioning and discussion. The questions may be summarized as follows : 1. If ferrite is formed by cold-working austenite, what happens to the carbon with which the ferrite and austenitc are both presumably supersaturated? 2. What is the nature of the alpha-ferrite formed at grain boundarices by chromium-carbide precipitation at these boundaries?

Jan 1, 1940

By R. Buehl, John Wulff, H. Hollomon

Although the main features of the transformations occurring in 18-8 have been published already, certain conclusions merit questioning and discussion. The questions may be summarized as follows : 1. If ferrite is formed by cold-working austenite, what happens to the carbon with which the ferrite and austenitc are both presumably supersaturated? 2. What is the nature of the alpha-ferrite formed at grain boundarices by chromium-carbide precipitation at these boundaries?

Jan 1, 1940

By Richard D. Hagni

Mississippi Valley-type ore deposits contain significant quantities of minor elements, which are present partly in the form of separate mineral phases and partly in solid solution in the major sulfide phases for which these deposits are exploited. These elements, as separate phases, are: copper, mainly in chalcopyrite and enargite; cobalt and nickel, chiefly in thiospinels and bravoite; rare earth elements associated with certain fluorites; and native gold. Many economically important minor elements occur in solid solution in sphalerite, including silver, cadmium, iron, germanium, gallium, indium, thallium, cobalt, nickel, and mercury. Significant amounts of silver and antimony, and perhaps very small amounts of gold, are present in solid solution in galena. Chalcopyrite may contain small amounts of silver, molybdenum, bismuth, cadmium, cobalt, and nickel. Marcasite and pyrite may contain silver, thallium, cobalt, and nickel. Although some of the minor elements contained in the Mississippi Valley-type deposits are currently recovered at the smelters and refineries, many are lost in tailings, sludges, and slags; consequently, important quantities of these elements are potentially recoverable as non-conventional resources.

Jan 1, 1983

By R. J. Towner

Tensile properties of Aluminum Powder Metallurgy (APM) products at 600°, 800°, and 1000°F were lowered by cold reductions of as little as 10 or 20 pct. The detrimental effect of cold work on yield strength at elevated temperatures increased with temperature. Heating cold-worked products at 850° to 1150°F removed the structural effects of cold work through the process of recovery and restored, at least partially, the strength at 600°F to the level of hot-worked material. Material containing 5 pct A1203 was recrystallized by cold reductions of 97 pct or more followed by annealing at 1100°F. Recrystallization lowered sharply the strength at room temperature, but raised the strength at 600°and 800°F relative to that of the cold-worked state The high strength of Aluminum Powder Metallurgy (APM) products at elevated temperatures'-4 is well-known. In this paper, some conditions of processing that can affect this important characteristic are presented. The following nomenclature will be used to identify different alloys: All of the above alloys are of the aluminum-aluminum oxide type made from milled powders of commercially pure aluminum with the exception of M486, which is fabricated from atomized A1-Fe alloy powder. The products made from milled powders are hardened by a dispersion of aluminum oxide par- ticles in the aluminum matrix, while the intermetal-lic compound FeAL is the dispersion hardening agent in M 486.' The process used for making all APM products involves the application of heat and pressure to form a compact from powder which is fabricated into an extrusion, sheet, strip, or wire by standard techniques. Probably the most common cold-worked APM product is sheet. Cremens, Bryan, and rant' determined the room-temperature tensile properties and the 600°F stress-rupture properties of XAPOOl and XAPOO3 sheet and reported that there was little difference between the as-extruded, cold-worked, and annealed at 1200°F conditions. On the other hand, Emmons6" found that the tensile and stress-rupture properties of XAPOOl and XAPOO3 sheet at 600" and 800°F were lower than those of extrusions. The tensile properties of XAPOO3 sheet were also determined at elevated temperatures by Doyle' and ~ayward.' According to Friske" and Kendal et a1.," cold working by swaging, rolling, and tube drawing reduced the tensile and creep-rupture strength of XAP 001 Recrystallized aluminum powder metallurgy products are rare because the dispersion in the aluminum matrix is usually too fine, uniform, and concentrated to permit recrystallization. However, Lenel12 was able to recrystallize wires made from aluminum powders containing about 1.75 and 3.0 pct oxide and found that the tensile properties at room temperature remained higher than those of annealed commercially pure aluminum because of the dispersed oxide particles. Westerman and Lenel13 found the kinetics of recrystallization of the powder products were very different from those of cold-drawn commercially pure aluminum wire. The alloy containing 3.0 pct oxide recrystallized to a very coarse grain size was more creep-resistant at 400" to 600°C (752" to 1112°F) than in the as-extruded, fine-grained condition, according to Ansell and weertman.14 Ansell and aenel" further studied creep at 500" to 620°C (932" to 1148°F) of recrystallized 1.75 pct oxide wire and confirmed the creep model of Ansell and Weertman. The present work is being reported for the fulfillment of the following objectives: 1) to show the effect of cold work on tensile properties at elevated temperatures;

Jan 1, 1964

By Ihor A. Kunasz

Introduction Lithium minerals occur predominantly in pegmatites which contain mineral assemblages derived from the crystallization of postmagmatic fluids or from the metasomatic action by residual pegmatitic fluids. They have been the traditional sources of raw materials for ceramic and chemical industries. With the discovery of Searles Lake, brines became new sources of lithium. Indeed, the 1960s may well be referred to as the "brine decade" because several brine bodies of significant economic importance were discovered. In the United States, the brines of Clayton Valley, Nevada, are presently exploited by Foote Mineral Co. The brines of the Great Salt Lake of Utah, the Smackover formation, and the Imperial Valley geothermal field, have been defined as important resources of lithium. In South America, new occurrences have been identified in Bolivia and Argentina. At the Salar de Atacama, Chile, new production capacity is scheduled for 1984. Following the termination of the AEC purchase program in 1959, several companies such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp. were forced to close their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminum potlines), the lithium industry grew steadily, and with the potential application of lithium metal in batteries and nuclear reactors, a healthy growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded, reserves as well as the search for new sources from which lithium could be extracted economically. Geochemistry of Lithium Lithium is the third element in the periodic table. It is the lightest of all the metals, having an atomic weight of 6.938, an ionic radius of 0.68Å and a charge of +1. The geochemistry of lithium has been extensively studied and has been summarized by Rankama and Sahama (1950), Goldschmidt (1937), and Hortsman (1957). The distribution of lithium in igneous rocks is controlled by its size and its charge, and by the (MgO+FeO) / Li2O ratio. In the early stages of crystallization of a magma, that ratio is very large. Consequently, both magnesium and iron are removed by ferromagnesian minerals in preference to lithium which is then concentrated in the residual magma. This results in an enrichment of lithium in silicic rocks and pegmatites (Strock, 1936). Pegmatites are coarse-grained igneous rocks formed by the crystallization of postmagmatic fluids. Minerals within pegmatites may also form by metasomatism (Jahns, 1955). Genetically, the pegmatites are associated with neighboring intrusives. Mineralogically, granitic pegmatites contain feldspar, quartz, and mica as the main constituents and a variety of exotic elements such as lithium, beryllium, tantalum, tin, and cesium, which may or may not occur in economically significant concentrations. Detailed studies by numerous investigators (Cameron et al., 1949, 1954; Hanley et al., 1950; Jahns, 1953, 1955; Page et al., 1953) indicate that pegmatites often exhibit an internal zonal arrangement, with each zone containing a specific suite of minerals. The lithium minerals are usually found in the intermediate zones, and although as many as 13 zones have been recognized by Cameron, et al. (1949), a complete zonal arrangement is rarely found. Zoning of pegmatite bodies has also been observed on a regional basis. The regionally zoned pegmatite sequences exhibit mineral assemblages and complexity according to their re-

Jan 1, 1983

By N. E. Truitt, D. G. Russell

The transient pressure behavior of a well which produces a single compressible fluid through a singte-plane wrticat fracture has been investigated mathematically. The fracture is assumed to possess infinite flow capacity, to be of limited mdial extent, and' to penetrate the producing formation completely in the vertical direction. Previous studies of vertically fractured wells have been concerned primarily with production rate performance or semisteady-state pressure behavior. This study was undertaken to ascertain the influence of vertical fractures on transient pressure tests such as pressure build-ups and flow tests. In a vertically fractured system, flow in the region nearest the fracture is practically linear, whereas farther away from the fracture essentially radial flow prevails. Thus, transient pressure analyses based on radial flow theory are somewhat inaccurate. As fracture penetration increases radially, kh values calcutated from pressure build-up and flow test curves become increasingly larger than true values. Failure to consider the effect of fracture penetration also introduces inaccuracies into the catculation of fracture length from the apparent skin factor and into the determination of average reservoir pressure. If the total length of the fracture is 20 per cent, or greater, of the drainage radius of the well, corrections must be made to pressure build-up and flow test results. Methods for correcting such results are discussed in this paper. For wells with prefracturing pressure build-up or flow test data, it is possible to estimate fracture length by comparison with postfracturing build-up or flow test results. In new wells or wells without prefracturing build-up or flow test data, fracture length must be estimated to correct the values obtained from analysis of pressure tests after fracturing. Fracturing efficiency calculations should be made whenever possible to provide an estimate of fracture length. Tables of the dimensionless pressure drop as a function of time and fracture penetration are included in this paper. Using these values should permit analysis of other types of transient pressure behavior in vertically fractured wells. INTRODUCTION Hydraulic fracturing has been used quite successfully for over a decade as a completion and stimulation technique in oil and gas wells completed in low-permeability reservoirs During this period a considerable amount of theory has evolved on the performance of hydraulically fractured reservoirs and on more efficient means of artificial fracturing. Although theory has been developed, no rigorous investigation has been made of pressure build-up and flow test behavior in such wells. Prats et al.1 first discussed the performance of vertically fractured reservoirs for the case of a compressible fluid. Their work was primarily concerned with production performance at constant flowing pressure. These authors also considered large-time (semisteady-state) constant production rate behavior for vertically fractured wells; however, transient pressure behavior at constant rate was not investigated. McGuire and Sikora10 and Dyes, Kemp, and Caudle2 employed an electrical analog to investigate the influence of artificial vertical fractures on well productivity and pressure build-up. They found that fractures which extend beyond 15 per cent of the drainage radius away from the well alter the position and slope of the straight-line portion of the build-up curve. They concluded that these effects must be considered both in the determination of the effective permeability of the formation and in any calculations of final build-up pressure. Although these authors did not undertake an exhaustive study of the influence of vertical fractures on pressure build-up performance, their limited results were quite interesting from the standpoint of the effects they demonstrated. In a more recent paper, Scott- reported the results of an investigation of the effect of vertical fractures on pressure behavior, which was conducted with a heat flow model. Scott's results appear to be consistent with those reported in Refs. 1 and 2. However, the effects of different fracture lengths on performance were not investigated. Pressure build-ups and transient flow tests are among the most diagnostic tools available to the reservoir engineer or production engineer. Since a very high percentage of present-day well completions incorporate the hydraulic fracturing technique, a definite need exists for information on the effect of fractures on transient pressure performance. For these reasons we have undertaken a rigorous study of pressure build-up and flow test behavior in vertically fractured reservoirs. The objectives of this study were (1) to obtain synthetic pressure build-up and flow test

Jan 1, 1965

By Kenneth W. Luke

A computer programing system has been devised to assist in open pit mine design planning. This system operates upon data generated for cross sections in the mine plan, and parallels present manual methods used in mine design, resulting in a minimal communications barrier between the mine planner and the computer. Input data for each cross section includes geologic interpretation and mine design parameters such as wall angles, bench heights, berm widths, and ramping system. The program will optimize the design of each cross section to give minimum stripping at any desired ore reserve level. This system is functional in the sense that it is easily adopted, changes in mine design parameters can be quickly evaluated, and each resultant design incorporates all recognized mining constraints.

Jan 1, 1973

By A. A. Smith, J. S. Smart

THE controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modem copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range 0 to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously.1-2-3 Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,1, 2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of 3/8-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 850°C. from a surface scale. Test wires were drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at o.3125, 0.257, o.204 and o.162 in., and a final cold reduction of 95 per cent t0 0.081 in. Oxygen-bearing slugs made by remelting were hot-rolled to 5/16 in., drawn to 0.162 in., annealed for 30 min. at 600°C. and cold-drawn 95 per cent to 0.081inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 5/16-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700° to 800°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals were of one hour duration followed by a rapid quench in 10 per cent H2SO4. EFFECT OF PHOSPHORUS The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1945

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By Joseph E. Pogue

The petroleum industry has been involved in Lore collective planning than any other American industry, with the exception of the railroads and utilities, and therefore is of interest as a case study in the experimental attempts to regulate the economic consequences of free competition. Planning is of course an integral part of effective management, hence at the outset a distinction must be clearly drawn between competitive planning and collective planning. By competitive planning is meant the aggregate of plans drawn up and prosecuted by the competing units occupying a field of enterprise; by collective planning is meant a collusion of plans, either originating among some or all competitors, or else imposed upon them, whether accepted or resisted, by some superior authority, usually the state. The prevailing popular concept of "planning" as applied to industry appears to be a program of conduct superimposed upon an industry unwilling or incapable of achieving a socially and economically desirable result under free competition. In this brief and tentative analysis of the subject, competitive planning is left to one side and attention is focussed upon the matter of collective planning as defined above. A basic functional difference between the two categories of planning is that in the case of competitive planning the individual plans are small, numerous, and tend to offset one another when in error; whereas in the case of collective planning, the separate plans are larger in scope, fewer in number, and tend to escape the incidence of the principle of compensation. In viewing the evolution of collective planning in the petroleum industry we find that during the past 20 years there have developed four more or less well defined collective plans and that at the present time the industry is deeply involved in a collective planning trend pointing toward further varieties. The four plans, which are to some degree transitional, may be conveniently named from the chief incidents that led to their formulations. The first collective plan was the program of control developed during the World War and hence called the war plan. The second plan was one originating within the industry in the period between the war and the inflation of the late twenties and called the inventory

Jan 1, 1935

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By Eugene P. Pfleider

RECENT interest in germanium centers around its use as a semi-conductor of electricity in electronic devices. It is generally believed that germanium transistors, diodes, triodes, photocells, and rectifiers will largely replace the present-day vacuum tubes. The germanium electronic devices are much smaller, lighter, and more resistant to shock, and they require only a small fraction of current required for conventional devices. Hence only a small amount of heat is given off by the equipment. This development will require many times the quantity of germanium now being produced, which in 1948 was approximately 1000 lb' and was obtained almost entirely from zinc ores in Missouri, Kansas, and Oklahoma. No one knows with certainty what the demand will be for ger-manium by 1956. It may be 40,000 lb.1 Known concentrations in zinc ores are not sufficient to

Jan 1, 1954

By P. H. Royster, T. L. Joseph

In a study of the blast-furnace process, the Bureau of Mines has made many experiments for the purpose of determining the exact nature of the combustion of coke in the neighborhood of the tuyeres. Two papers1 presented at a meeting of this Institute discussed somewhat the practical aspects of coke combustibility in its relation to the operation of the blast furnace. In a later paper,2 Sherman and Kinney discussed the possible effect of variations in the combustibility of cokes on the furnace operation, and find that the "reoxidation theory" of Koppers and the "heat concentration theory" of Brassert³ are insuffcient to explain the variation in the conduct of different cokes that has been observed by furnace operators. In their report to the D-5 Committee of the American Society for Testing Materials, with which the Bureau of Mines has been cooperating, Perrott and Fieldner4 seem to agree with Sherman and Kinney that, for practical purposes, the nature of the combustion of coke at the tuyeres of any furnace is constant and is affected neither by the physical properties of the coke nor by the nature of the furnace operation. They omit as unimportant any tests on the combustibility of coke from their proposed methods for standard tests on coke. In the last two papers, it is pointed out that performance tests, in which all other factors except coke quality are kept constant, are to be desired and

Jan 1, 1924

By R. P. Heuer

In recent years an increasing amount of research work has been done on refractory materials for use in copper-smelting furnaces. A few of the larger refractories manufacturers have erected special research laboratories which are fully equipped to study the refractory problems of the smelter. A typical laboratory of this type was described in the January, 1929, issue of Mining and Metallurgy, in an article entitled "Methods of Research Newly Applied to Refractories," by W. F. Boericke. This particular laboratory is equipped for the manufacture of full-size refractory brick. It aims to study on a fairly large scale the behavior of various refractory raw materials and the effect of improved methods of manufacture. The refractories manufacturer has at his disposal the naturally occurring refractory oxides in various degrees of purity, mixed or combined with other oxides. In order to supply the copper smelter with a refractory brick that will permit the most economical operation of the smelting furnaces, it is necessary to have the optimum combination of a number of both physical and chemical properties in the brick. Unfortunately, nature has not provided any raw materials in which the perfect combination of these properties exists. It is, therefore, a problem for man's ingenuity to seek out the most desirable raw materials and develop methods of manufacture that give, in the resultant product, the necessary combination of properties in as full a measure as is possible. In the laboratory it is possible to carry out fairly broad experiments with this objective. It is first necessary to obtain and process the raw materials, then to manufacture them into brick and finally, to test these bricks under conditions designed to interpret or simulate in the laboratory the actual conditions in the smelting furnace. It is necessary for the research engineers to determine certain fundamental properties in the brick which may be subjected to laboratory measurements and to interpret these measurements in terms of brick performance in smelting-plant practice. Such procedure is not what might be called an exact, scientific one but it has been found that great progress can be made when these principles are applied. For example, the resistance of refractory brick to spalling and thermal change can be related to the thermal expansion of the refractory, its thermal conductivity and heat capacity and its

Jan 1, 1934

By Josef Intrater

A dilatometric determination of the a + ß region temperature limits was performed on vacuum melted Zircaloy-2. The temperature of transformation for a-a+ß and a+ß — ß on heating and cooling as a function of rate of heating and heat treating history was studied. The limits were found to be 815° to 830°C to 975° to 995°C on heating and from 960° to 930°C to 785° to 770°C on cooling. A 5° to 15°C increase was observed for a- a + ß with increased rate of heating and a 20° to 30°C decrease for ß - a + ß with increased rate of cooling. 1 HE transformation temperature for pure zirconium has been determined by many investigators1-5 using metallography, electrical resistivity measurements, and dilatometry. The effect of the rate of cooling on the transformation temperature of zirconium has been studied by Hayes and Kaufmann6 and Duwez,7 and the effect of alloying elements by pfei18 and McGeary.13 Since the development of Zircaloy-2, the limits of the a + ß region for that alloy have been also determined. The first reported temperature for the a — a + a transformation in Zircaloy-2 was 900°C and for a + ß - ß 1000C Subsequent studies by Picklesimer and damson" indicated the beginning of the transformation at 810°C, and the metallographic study by the Technology Group of the Special Materials Section at the Westinghouse Bettis plant1' suggested that 820°to 830°C is the temperature of transformation. The dilatometric investigation by the latter group yielded 830°C for the beginning of the transformation. Thomas and Forscher12 set the beginning of the transformation at 900 °C on heating and the end of the transformation at 870°C on cooling. The above investigators stated in their paper that the dilatometric curve exhibits features caused by a eutectoid reac-

Jan 1, 1962