Search Documents

By H. Kenworthy, R. B. Fisher, R. G. Knicherbocker, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2, with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite-type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore. History The occurrence of titanium minerals in the Magnet Cove area of Arkansas was recognized as early as 1890, but it was not until about 1912 that any appreciable prospecting for the minerals was undertaken. At that time drilling was begun, a shaft was sunk, and several drifts were driven, but beneficiation to recover the titanium minerals was not attempted. The only successful mining and milling operation of the Magnet Cove rutile deposit was begun in 1932 by the Titanium Corp. of America and continued until 1942. The ore was washed by means of a rotary scrubber and then deslimed in a drag classifier. The discharge was ground in a rod mill, classified, and tabled to recover a rougher rutile concentrate, which was screen-sized and retabled on cleaner tables. The cleaner concentrates were given a reducing roast, screen-sized, and magnetically separated to produce a finished rutile concentrate. Most of the rutile produced during this period was sold abroad. In 1942, the Titanium Alloy Corp. of Arkansas (a subsidiary of the Titanium Alloy Manufacturing Co. of New York) purchased the property and rebuilt the mill. Subsequently, the plant and property were acquired by the Magnet Cove Rutile Co., Inc., of Little Rock, Ark., the present owners. Very little titanium has been produced since 1942. Although the Titanium Corp. activities yielded enough returns to allow continued operation for approximately 10 years, certain factors must be recognized. These are: (1) production of rutile in that period was during a low in the economic cycle which permitted low-cost operation on a small scale, and (2) a considerable portion of the production was above the water level and no drainage problems existed. Prior to this paper there has been no published report of any mineral-dressing investigation of the lower levels of the ore body. Reference is made in another paper1 to an earlier investigation of Magnet Cove rutile by the Rolla laboratory, in which it is stated that recoveries of 12 to 17 pct of the rutile were obtained. The present investigation was undertaken to improve the known milling processes and to provide adequate metallurgical information about the ore treatment. Titanium Technology The titanium mineral of primary interest in the present investigation was the titanium dioxide, rutile. Rutile is one of the industrial minerals whose annual consumption is relatively small but strategically important. The domestic production of rutile was 7100 tons in 1948. The imports of rutile in the same year were approximately 8000 tons.2 A major use of rutile is in the production of welding-rod coatings, for which a product containing a minimum of 92 pct titanic oxide is desired. Other constituents, such as lime, silica, and sulphur, must be held to a minimum, but hard-and-fast specifications for these elements cannot be drawn. It is necessary to incorporate the rutile in a welding-rod coating, make a sufficient number of test welds, and then determine the tensile strength of the weld metal in the as-welded and stress-relieved conditions. Such a test gives

Jan 1, 1950

By A. W. Schlechten, A. H. Larson

Equilibrium H2S/H2 ratios were determined as functions of temperature (500o to 900°C) and composition in a hydrogen-circulation apparatus. Within the composition range studied there exists a two-phase region of "Zr3S4" and "ZrS2". The upper composition limit of this two-phase region is hounded by a disulfide phase and is practically constant over the temperature range investigated. The lower composition limit of this two-phase region is bounded a "Zr3S4 " phase and varies appreciably with tem- perature. The upper composition limit of the homogeneous region of the disulfide phase is not definitely determined, but it appears to he bounded by the stoichiometric composition of ZrS2. The lower composition limit of the homogeneous region of the Zr3S4 phase could not he determined due to the extremely low values of the equilibrium H2S/H2 ratios. Various thermodynamic quantities are evaluated from the data. PUBLISHED free-energy data for the Zr-S system are practically nonexistent. Strotzer, Biltz, and Meisel1 measured the sulfur pressures for the reaction 2ZrS2(s) + S2(g) = ZrS3(s) in the temperature range 783" to 874°C. The average heat of reaction calculated from the temperature dependence of the sulfur pressure is -47 keal. It should be noted, however, that according to these investigators, the two-phase region as determined by sulfur pressure constancy under isothermal conditions extended from approximately ZrS2, 3 to ZrS2.7. From consideration of X-ray data they concluded that the homogeneous regions of the disulfide and trisulfide phases are ZrS1.8-2.0 and ZrS2.8-3.2, respectively. Hahn and coworkers2 have made a structure study of the zirconium sulfide phases. They summarized the zirconium sulfide phases as follows: the compounds ZrS3 and ZrS2 with narrow homogeneous regions, a "Zr3S4" phase with a homogeneous region roughly within the limits of ZrSl.5 and ZrSo.9, the compounds ZrS and Zr4S3, and a "Zr3S2" phase with a homogeneous region within the limits ZrSo.8 and ZrSo.5. It is noted that the compounds ZrS and Zr4S3 are only formed in the gaseous state through sublimation of a phase which has the approximate composition of the compound. This paper describes the determination of the stability of the zirconium sulfide phases by a hydrogen-reduction method in which hydrogen is circulated over the heated sulfide until equilibrium is attained. The resulting H2S-H2 mixture is then analyzed. Partial molar free energies, enthalpies,

Jan 1, 1964

By C. R. Fondersmith, John Chipman

In the manufacture of rimming steel—which constitutes the bulk of the world's production of mild steel—the factors that determine the quality of the product are very closely associated with the pouring and solidification of the steel in the ingot mold. The behavior of the metal in the mold is, on the one hand, the resultant of the complex processes through which the liquid metal has passed, and, on the other, it is an indication of the probable behavior of the ingot during subsequent rolling and finishing operations. A detailed study of the mechanism of solidification of rimming ingots ought to yield information that will be useful in controlling the structure of the ingot and the quality of the ultimate product. The first step in such a study is to determine the rate at which the solid shell of the ingot forms from the liquid metal in the mold. A knowledge of the rate of solidification will make it possible to correlate observations of rimming action and gas evolution with studies of the structure, porosity, and segregation within the ingot. Thus, if the metal in the mold is observed to fall, let us say one minute after pouring, the portion of the structure associated with this fall will be located in the part of the ingot that is solidifying at that particular moment. The knowledge that the ingot solidifies to a depth of 3/4 in. in the first minute enables us to locate in the ingot the structural features corresponding to the observed fall. Conversely, the blowhole condition associated with a rising or growing ingot will be found in the part of the ingot that is solidifying at the time the phenomenon occurs. The time required for the complete solidification of an ingot has long been a matter of speculation. It is of considerable practical importance in connection with charging and heating in the soaking pits. Too rapid handling of the ingot through heating and rolling processes has been thought to be associated with excessive pipe and other internal defects, so that a further object of this investigation was to attempt to estimate the time required for complete solidification, or the minimum practical time within which the subsequent operations can be performed with the minimum hazard.

Jan 1, 1937

By D. Gupta, S. Weinig

This investigation comprises the study of dislocation-oxygen interactions in a! titanium and its effect on the ductile to brittle transition in titanium. Internal friction techniques using a low-frequency lorsion pendulum were used to study the oxygen atom interactions with dislocations in "superpurity" titanium. A calculation of the interaction energy between an oxygen atom and a dislocation, based on the "breakaway" strain resulted in a value of 0.015 ev as compared to theoretical values of 0.022 and 0.035 ev for edge and screw dislocations, respectively. Both the saturation of the room temperature decrement and the transition from ductile to brittle behavior occurred at 1.5 at. pct 0. It was proposed that the embrittlement was due to oxygen atoms immobilizing the dislocations. It was possible to increase the ductility of the Ti-0 binary alloys by decreasing the oxygen pinning. The increase in uniform elongation was 30 pct for an increase in the preanneal temperature of 300°C. ThE room-temperature ductility of a titanium is significantly affected by interstitial solutes. Although oxygen has a solid solubility of 15.5 pct by weight, the room-temperature ductility extends only to 0.6 pct.' The ductility precipitously falls at this concentration and the fracture characteristics change from ductile to brittle.2 The small effective bulk composition of solute required to destroy the room-temperature ductility of the titanium must be indicative of an in-homogeneous distribution of solute atoms. Internal friction techniques were used in this investigation to

Jan 1, 1960

By W. E. Hess

AT the Vesta mines of Jones & Laughlin Steel Corp. on the Monongahela River, 35 miles south of Pittsburgh, JCM Joy continuous miners and 6-SC shuttle cars are used for pillar extraction in the Pittsburgh seam. The entire output of the mine goes into coke production for blast furnace operation. Because this coal, which has high metallurgical qualities, is close to the place where it is ultimately used and because supplies with these properties are being rapidly depleted, complete recovery is essential wherever possible. With the introduction of the continuous miner into the Vesta mines, therefore, it was necessary to plan a project which would facilitate development and provide for future total recovery. Use of continuous miners under varying conditions has necessitated changes with regard to roof action, method of development, method of pillar attack, and innovations in mining. In the following pages these changes will be discussed. Prior to the introduction of continuous miners the Pittsburgh seam at the Vesta mines averaged 72 in. of mineable coal, overlain with 12 to 16 in. of draw-slate, which weathers on exposure to air and is not firm enough to be held in place. Immediately overlying the drawslate is a wild or rooster coal, very irregular in thickness, varying from 12 to 30 in. Above the rooster coal the strata consists predominately of shales or lime shales and sandstone. Just before the introduction of continuous miners in the Vesta mines, however, a definite change took place in the character of the roof structure overlying the coal seam, see Fig. 1. Thickness of laminated roof immediately overlying the rooster coal varies with localities and introduces a problem in roof control. In fact, a set of eight main entries being developed in Vesta NO. 4 mine entered an area with so difficult a roof structure that management considered abandoning the section altogether. In this locality the roof consisted of thin alternate layers of roof coals and shales, with an occasional irregular seam of slick slate, the whole being laced with slips, and the coal itself being cut by clay veins and spars. In an effort to overcome some of the difficulties, roof bolting was introduced in 1949. This made it possible to recover coal from an area which otherwise would have been economically unmineable. There have been very few roof bolt failures. When conventional machines were replaced by continuous miners there were changes in the development of butt entries. By these changes it was hoped: 1—to speed development, 2—to provide as much solid coal as possible for the machine on retreat, 3—to avoid the necessity of crossing entries already driven, 4—to facilitate ventilation, 5—to provide a roadway for shuttle car haulage which would eliminate the necessity of running through doors or curtains, 6—to provide better roof control by increasing the distance between the center lines of entries, and 7—to provide more coal when the machine was in position to load.

Jan 1, 1956

By William G. Fricke

MaCROSEGREGATION, as distinct from microseg-regation, is often inverse in nature. That is, the eu-tectic solute elements, which are expected to be con-

Jan 1, 1970

The first record of coal anywhere in the Appalachian regions of which we now know is along the north fork of the Potomac River, above the mouth of Savage River, on a map entitled, A Plan of the upper Part of Potomack River call Cohongorooto Survey'd in the Year 1736. Benj. Winslow1 two "Cole-mines" are shown, one just above Green Island and the other just below Hopwood Run. Winslow was in charge of a surveying party to "Lay out the Bounds of the Northern Neck of Virginia," or Lord Fairfax's Grant, his party locating the liver above the mouth of the Shenandoah, while another party located it below that point, and then around Chesapeake Bay and up the Rappahannock River. The results of the two surveys were combined in a map called, The Courses of the Rivers Rappahannock and Potowmack, in Virginia, as surveyed according to Order in the Years 1736 & 1737, made by Wm. Mayo, which does not show the "cole-mines;" this map was used with the report of the boundary commission which was sent to London in the case before the Privy Council. The boundary line decided upon was surveyed on the ground in 1746, just ten years after the original one. The results of this work were shown on A Map of the Northern Neck in Virginia, According to an Actual Survey begun in the Year MDCCXXXVI, and ended in the Year MDCCXLVI, Drawn by Peter Jefferson And Robert Brooke, Surveyors, which is now in the Colonial Office in London. This map shows the "cole-mines" in the same location as on Winslow's map, and taken from his record, of course, as that part of the survey was not retraced. Faulkner, who examined all of these records in his review of the case in 1832, refers to the notes of the original survey as "No. 10. The original field notes of the survey of the Potomac River, and the mouth of the Shenandoah to the head spring of said Poto¬mac River, by Mr. Benjamin Winslow." While the notes of the 1746 survey are in the London records and photographic copies of them are in several libraries in this county, the notes of the 1736 survey cannot be found anywhere. (For Chas. J. Faulkner's report, dated Nov. 6, 1832, see Kercheval's History of the Valley of Virginia, pp. 160-173. Jas. W. Foster's Maps of the First Survey of the Potomac River, 1736-37, in Wm. and Mary College Quarterly History Mag., April, 1938, gives a complete history

Jan 1, 1942

By H. H. Hausner, S. Storchheim, J. L. Zambrow

The solid state bonding of aluminum to nickel was studied as a function of temperature, pressure, and time at pressure. The initial results indicated that as the reaction conditions were varied, marked changes in tensile strength occurred. Plots of the log penetration coefficient vs the reciprocal of absolute temperature for various isobars were straight lines displaced from each other. THE techniques of bonding different metals to A each other include brazing, welding, welding by application of a molten phase, and solid state welding without any molten phase present. This last technique, the pressing of metals either at room temperature or at some temperature below the melting point of the metals to be joined, seems to offer interesting possibilities for bonding purposes. However, this technique has not been completely investigated, and very little is known about the diffusion phenomena which occur during solid state welding. Some previous work on the effect of pressure on diffusion1 was inconclusive. This paper is concerned with an investigation regarding the effect that the processing variables, such as pressure, temperature, and time at pressure, have in solid state bonding. The tests were made with aluminum and nickel and special emphasis was given to the strength of the bond between these two metals and to the intermetallic penetration rate during the bonding process. It seems that the effect of pressure on the intermetallic penetration is of particular importance for practical purposes and this effect was therefore studied in detail. Procedure Apparatus: The means of solid state bonding used for this study was that of the hot-pressing technique. This method requires the equipment pictured in Fig. 1 and involved the following procedure. The two metals to be bonded were placed in an aquadag lubricated 18-4-1 tool steel die, 16 in. high by 1.440 in. ID, between punches of 1.366 in. diameter made of the same material. A thermocouple

Jan 1, 1955

By R. A. Spurling, C. G. Rhodes

SATISFACTORY metallographic sample preparation of very soft metals, such as lead and its alloys is generally difficult. The prime requisite of any technique must be that the result gives an undis-torted microstructure for the microscopist to examine. A small amount of mechanical polishing followed by a chemical or electrolytic polish is usually the most desirable way to obtain an undis-torted surface. Several chemical-4 and electrolytic3-' polishing solutions have been developed for dilute lead alloys. Perchloric acid mixtures (with acetic anhydride, ethyl alcohol, or water) are among the most prominent electropolishing solutions used for lead; however, the presence of bismuth in the alloy precludes the use of any perchloric-containing solution. The other solutions1-7 were found to be unsatisfactory on alloys ranging from 10 to 65 wt pct Bi in lead. With increasing bismuth content, the microstructure shows a lead (terminal solid solution), 0-6 mixture, E (peri-tectically formed hexagonal phase), and E bismuth mixture (eutectic at 56.7 wt pct Bi).9 The metallographic samples were mounted in "Araldite" epoxy (the heat generated during polymerization does not alter the microstructure), ground by hand on well-waxed silicon carbide papers (400 and 600 grit), and polished with 3- and 0.25-CL diamond paste on billiard and microcloths, respectively. The use of the various polishing and etching solutions reported in the literature resulted in the formation of irremovable reaction products on the sample surface when applied to "as-ground" or "as-polished" surfaces. The E phase was the most difficult to clean chemically and in the development of an etchant for this system several solutions which satisfactorily etched the bismuth or a phase were unacceptable because of their reaction with the E. It was found that a mixture of 50 ml lactic acid 30 ml nitric acid 20 ml (30 pct) hydrogen peroxide (Solution #1) was a satisfactory etchant for the a-matrix alloys. The samples were prepared as before and etched after 1 min of polishing with 3-p diamond paste. The etchant was applied by swabbing (light pressure) for 30 sec to 1 min and the sample was then rinsed in running water. The E has a slight stain and the a is fairly bright, Fig. 1.

Jan 1, 1965

By G. W. Healy, D. C. Hilty

MAJOR considerations in the production of stainless steel are the utilization of stainless steel scrap and the recovery of chromium and other metallic values from the initial furnace charge. The decarburization of a bath of molten chromium steel with gaseous oxygen is usually accompanied by a considerable amount of metallic oxidation. Since recovery of this metal from the slag may require substantial expenditures of time and materials for slag reduction, holding metallic oxidation to the minimum consistent with good operating practice is generally desirable. The important role of temperature in minimizing metallic oxidation is illustrated by Fig. 1, taken from the results of Hilty, Healy, and Crafts,' who established the quantitative relations connecting the amounts of chromium, manganese, and iron oxidized during the oxidizing period of chromium steel heats with the composition of the initial charge and the temperature and composition of the molten bath after oxidation. Higher temperatures after the oxygen blow result in lower metallic oxidation. Although high temperatures are desirable for minimizing metallic oxidation, practical operating considerations limit the degree to which they can be employed. Excessively high temperatures or prolonged operation at moderately high temperatures may cause serious damage to the furnace refractories, so that a compromise must be effected. The problem, therefore, is one of controlling the oxidizing period of chromium steel heats to the shortest time at the highest practical temperature. The most effective tool the steel melter has for attaining high temperature while decarburizing a chromium steel heat is now commonly considered to be the oxygen lance with an adequate supply of gaseous oxygen. In order for the tool to be effective, however, the heat resulting from the oxidation of carbon, chromium, silicon, manganese, and iron in the bath must exceed the heat losses from the furnace. General recognition, of this principle has stimulated a trend toward faster injection of oxygen. For example, Pachaly2 proposed a high temperature at the start of the oxygen blow or a high rate of oxygen input as a means of obtaining the desired carbon level with high chromium recovery. On the other hand, limited understanding of the specific effects of oxygen input rate has hampered development of optimum practices. As part of a broad study of the metallurgy of chromium steel melting, therefore, the Linde Air Products Co. and the Electro Metallurgical Co. at their Metals Research Labo-ratories have evaluated the heat-balance during the oxidizing period in terms of oxygen input rate. The evaluation has then been related to factors such as temperature increase, metallic oxidation, oxygen Utilization, etc., and extrapolated to include a wide

Jan 1, 1958

By Adrian Brown

INTRODUCTION The primary tool which is available to improve the stability of an open pit mine at a given slope angle is control of groundwater pressure. This paper sets out the methods by which water pressure control can be achieved in large mines in different materials. The emphasis of this paper is on large mine slopes because. these slopes exhibit the greatest need for groundwater control, the greatest economic benefit from groundwater control, and the greatest technical challenge in achieving groundwater control. STABILIZATION USING MTER PRESSURE CONTROL Groundwater pressures reduce the stability of slopes in two fundamental ways, as shown schematically in Figure 1. In the example, a horizontal failure surface intersects a vertical joint or weak zone. Water pressure acts: o On the base plane to reduce the normal force on the sliding surface and hence reduce frictional resistance to sliding, and o On the vertical back plane, to create a driving force for the system.

Jan 1, 1983

By Dan Crackel, G. G. Ramos, Mark Heisel

INTRODUCTION Feasibility studies indicated that a cratering type stoping method was best suited to the character of the first ore block at Carr Fork. This method known as vertical crater retreat (VCR) has since been modified to a combination cratering and deck blasting using VCR drop raises for initial undercut development . The modified form retains many of the advantages of VCR while allowing high tonnage production blasts which have offset many of the disadvantages. FIRST CONCEPTS AND PREMISES Geologic Considerations The Steep Highland Boy (SHB) skarn orebody, the first of several blocks being developed, is a steeply dipping 70° to 90° limb of a syncline, with a width averaging 25 m (82 ft). The bed has a consistent east-west strike length of over 400 m (1300 ft) and extends from the surface to depths of over 1000 m (3300 ft). The footwall is highly fractured quartzite and the hanging wall grades from garneti te to limes tone and hornfe 1s. Because of the limestone in the hanging wall, the hanging wall appears more competent than the footwall. The ore is garnetite with lenses of massive sulphide and magnetite. The quartzite footwall is highly fractured not only because of the bedding but also due to the folding and intrusion of the quartz monzonite. This irregular footwall outline of some stopes in- creases the likelihood of excessive dilution. The principal ore mineral is chalcopyrite with some bornite. The garnetite ore is quite variable in terms of compressive strength and drillability. In addition to the sulphide and magnetite lenses, it is transected by clay- altered dikes and major and minor north-east faults. TABLE (1) gives the range and mean strengths of the rocks. Investigating Mining Methods Initial consideration of a suitable mining method centered around maximum safety and efficiency with minimum potential dilution. The following major methods were considered and investigated. Cut and fill mining was eliminated because of low productivity, the cost and problems associated with providing fill, and the relatively unsafe nature of the method. Sublevel caving was rejected due to the unpredictable cavability of the waste and the geometry of the ore body. Conventional sublevel or blasthole methods require excessive development, as fan and ring drills are limited to efficient drilling in the 18 to 25 m range (60 to 80 ft). Mining downdip with equipment drilling small diameter holes would have required eight separate extraction/drill horizons with crosscuts and associated excavation in the main ore block. The use of down the hole (DTH) machines cap- able of drilling 165 m (6g in) diameter holes

Jan 1, 1981

By E. F. Bailey, W. J. Harris

THE temperature of the ferrite to austenite re-action is established frequently by continuous heating experiments. However, equilibrium studies of this reaction have demonstrated that austenite may form at temperatures considerably below those at which the reaction is first observed during continuous heating. Because of this discrepancy, tempering is sometimes performed above the true critical temperature and in these cases austenite forms during tempering. The lowest temperature at which austenite forms and the kinetics of the reaction have been studied by Bain,' Bleakney and Gros-venor,2 and Dube and Cunningham. This austenite can affect the properties either as austenite per se, if it is retained at room temperature, or as a decomposition product if it transforms. The effect of austenite formation during tempering on low temperature impact properties of an 8 1/2 pct nickel steel was reported by Brophy and Miller4 in work published after the present investigation was initiated. They concluded that the improvement in low-temperature notch toughness which followed tempering at certain temperatures could be attributed to the austenite formed during tempering. Kramer et al.5 found anomalous hardness increases and embrittlement after tempering of a low-carbon manganese-nickel steel. They concluded that austenite formed during tempering, and that the decomposition products were responsible for the increase in hardness and the embrittlement. Quan-titative correlations of the microconstituents and mechanical properties were not made by these investigators. The present study was undertaken in order to establish the kinetics of formation of austenite at various temperatures, the characteristics of the decomposition of this austenite, and the relationship between mechanical properties and the phases present. Experimental Procedure A low-carbon manganese-nickel steel was selected because of the sluggishness of its austenite decom-position reactions. The composition of this steel in percent was: C, 0.10; Mn, 3.52; Ni, 2.34; Mo, 0.52; Cr, 0.17; Si, 0.19; V, 0.15; P, 0.019; and S, 0.020. Samples were prepared by forging sections from a large ingot to 3/4 in. bars. Formation and decomposition of austenite were investigated by dilatometric techniques which were checked by X-ray measurements. Dilatometer specimens were hollow cylinders 1 in. long, 1/2 in. diam, with a 1/8 in. central hole. All specimens were aus-tenitized for 1 hr at 1650°F and quenched in water prior to insertion in the dilatometer. Oxidation was prevented by using an inert atmosphere of purified nitrogen. Dilation was measured with a dial gauge which could be read by interpolation to 0.00005 in. Temperature was maintained within ± 3°F by a Brown Electronik Controller. Chromel-alumel thermocouple leads were welded to opposite ends of the specimen with the specimen serving as the hot junction. As a check on temperature uniformity comparison was made of the specimen temperature as measured with the chromel-alumel leads and the temperature of the center of the specimen as measured with a calibrated platinum—platinum-rhodium thermocouple embedded in asbestos in the central hole of the specimen. During heating a 5°F temperature difference was noted below 1000°F, but none above, while in cooling, a 5°F difference was observed from 1300" to 735°F, but none below. Heating rates of 35°F per min and cooling rates of 60°F per min were employed for all dilatometric studies. For transformation studies below room temperature, the dilatometer was allowed to cool to 150°F and then was quenched into liquid nitrogen.

Jan 1, 1951

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electro-¦ chemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are moditied in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.1-3 In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative arid may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole' These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in pennsylvania, carried out by the pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, ill the published literature. The potential differences across the contacts of sandstone and shale are called ill this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored WeLl In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored With diamond tools. The potentials were first measured with fresh water in the hole. * null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and

Jan 1, 1946

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electro-¦ chemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are moditied in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.1-3 In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative arid may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole' These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in pennsylvania, carried out by the pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, ill the published literature. The potential differences across the contacts of sandstone and shale are called ill this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored WeLl In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored With diamond tools. The potentials were first measured with fresh water in the hole. * null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and

Jan 1, 1946

By Edwin B. Douglas

The Blackbird mine is owned by Calera Mining Co., subsidiary of Howe Sound Co. The mine is located in the Salmon National Forest, Lemhi County, Idaho, about 22 miles west of Salmon and 220 miles north of Pocatello. The thought of producing cobalt from a prospect that offered excellent opportunities stimulated everyone connected with this project. But as time went on, it was found that every phase of the development presented unusual difficulties.

Mar 1, 1956

By A. Phillips, D. H. Killpatrick, V. Kerlins

The tensile failure of two dispersion-strengthened Ni-20 Cr alloys was studied and compared to the fracture of a similar alloy with no dispersoid. The fracture characteristics were studied using electron fruc-tography and transmission electron microscopy. In all three cases, the mode of failure was found to be microvoid coalescence. The failure in the dispersion-strengthened alloys was found to have initiated at the particles. The size of the dimples in the fracto-graphs was found to be related to the spacing of the particles, but not to the total elongation before failure. The elongation before failure was found to be related only to the amount of dispersed phase. These results are compared to those predicted by a theoretical model of ductile failure. THE continually increasing strength requirements for creep-resistant materials capable of long life at service temperatures above 1600"F (875"C) have developed considerable interest in dispersion-strengthened nickel-base alloys. The high yield strength of these alloys results from the presence of a dispersion of fine particles of thoria which act to impede the normal motion of dislocations. Many theories have been presented to explain the role of the dispersion in the strengthening of these alloys. A good review of these theories is presented by Ansell.' The ultimate strength of such alloys is not only related to mechanisms raising the yield strength, but also to the amount of work-hardening which occurs. This work-hardening is determined by the work-hardening rate and the amount of plastic strain before failure. Since fracture limits the amount of plastic strain, a study was undertaken to gain a better understanding of the fracture mechanisms in these alloys. Electron fractography and transmission electron microscopy were used to study the fracture characteristics in two dispersion-strengthened alloys and one similar alloy containing no dispersoid. These results are related to the tensile properties of the dispersion-strengthened alloys at room temperature and at 2000°F (1095°C). The results are also related to a theory for ductile fracture. 1) PROCEDURE Standard tensile specimens were made from 0.020-in. (0.051-cm) sheets of three different Ni-Cr alloys. The alloys had nominal compositions of Ni-20Cr, Ni-20Cr-2Th0,, and Ni-2OCr-4Th0,. All alloys were supplied in an annealed condition. The specimens were fractured in tension at room temperature to determine the effect of the dispersed thoria on the fracture appearance. The tensile properties were determined from the average of a minimum of three ten- sile specimens for each condition tested. The fracture surface of all of the alloys was examined by electron microscopy using standard two-stage plastic-carbon replica techniques. Thin foils of the dispersion-strengthened alloys were used to investigate the size and spacings of the dispersion particles, and to investigate sections of the 2 pct thoria alloy taken from areas of the specimen adjacent to the fracture surface. The thin foils were mechanically ground to 0.010 in. (0.025 cm) and then chemically polished to approximately 0.001 in. (0.003 cm) in a solution of 29 g of ferric chloride and 10 ml hydrochloric acid in a liter of water. The polishing solution was maintained at 150"F (65°C) during the thinning operation. The final thinning of the foil was done electrolytically using a solution of 700 ml ethanol, 100 ml 2-butoxy eth-anol, 120 ml distilled water, and 78 ml perchloric acid (70 pct). The potential was maintained at 15 v and the bath temperature at -20°~ (-29°C) during the thinning operation. The final thickness of the foil was approximately l000A as determined from the width of twins boundaries observed in many of the foils. 2) RESULTS AND DISCUSSION The electron fractographs of the fracture surfaces of the alloys are shown in Figs. 1, 2, and 3. The normal interpretation of this type of fractographz is that, as a result of the difference between elastic and plastic properties of the matrix and the particles or other inhomogeneities in the alloy, microvoids are formed

Jan 1, 1969

By AIME AIME

THE Iron and Steel Division and the Institute of Metals Division are laying plans for a rousing meeting the week beginning Sept. 21 in the land of the bean and the cod-at Boston. The two divisions are collaborating with the American Welding Society, the American Society for Steel Treating, and the Iron and Steel Division of the A. S. M. E., to have technical sessions of widespread interest and social affairs that will compare with the best of previous years. In connection with the meetings an exhibition of production and testing equipment, heat-treating equipment, furnaces, welding equipment, and metal products will be held on Commonwealth Pier all week, where those attending may see the latest developments in the field of their own work.

Jan 1, 1931

By Rex E. Cheek, Donald E. Menzie

The fluid mapper, a model relatively new to the petroleum industry, was used to study the effect of various mobility ratios on the areal sweepout efficiency for two typical spacing patterns. The experiments indicated the areal sweepout for the five-spot pattern varied from 51.8 per cent at a mobility ratio of 0.093 to 89.1 per cent for a ratio of 24.4. In the direct line-drive pattern, the areal sweepout varied from 58.7 per cent at a mobility ratio of 0.089 to 92.0 per cent at a ratio of 24.8. The fluid mapper may prove useful to determine quickly the effective areal sweepout for any well spacing. INTRODUCTION The effect of the mobility ratio on the areal sweepout efficiency during primary depletion of a water drive reservoir and during secondary recovery operations has recently become more widely recognized The mobility ratio, M, is defined as: _ kjp (displaced fluid) k/u (displacing fluid) where k = effective permeability u = viscosity When the displacing fluid is miscible with the displaced fluid, the permeabilities are equal and the mobility ratio may be expressed as a ratio of viscosities: u (displacing fluid) u (displaced fluid) The mathematical analysis for calculating the areal sweepout efficiency with mobility ratio other than unity is quite tedious.5,11 An experimental method by using a potentiometric model2 in a step-wise manner and in using an X-ray shadowgraph model3,12 with continuous fluid flow has been published. Several types of models have been used to study oil and gas reservoir performance. These models may be classified as physical, electrolytic, potentiometric, X-ray shadowgraph, and fluid mapper. The X-ray shadowgraph and fluid mapper are models relatively new to petroleum engineering and have not been used extensively for specific applications. The theory of the fluid mapper indicates it may be adapted to a study of areal sweepout efficiencies for various mobility ratios as well as other complex problems in petroleum engineering. The use of the model and results obtained when using displacing and displaced fluids of equal densities but different viscosities are discussed. FLUID MAPPER DEVELOPMENT H. S. Hele-ShawV eveloped a fluid mapper model based on the hydrodynamic theory. This theory is that in the steady flow of a viscous fluid between horizontal parallel plates spaced a very small distance apart, the effect of viscous shear is of such magnitude in the vertical plane that the motion in the horizontal plane is practically undisbrted streamline flow. Techniques developed by Hele-Shaw were not expanded and no additional developments in fluid mapper models were forthcoming until A. D. Moore, University of Michigan, published a series of papers starting in 1949, which describe the construction of a flexible and inexpensive model'h nd the fluid mapper technique for the solution of certain problems.' The essential components of the fluid mapper as developed by Moore are::.ln 1. A base slab. made of dental stone (calcium sulphate and water). which is shaped to represent the prototype. 2. Plate glass slightly larger than the slab and spaced

Jan 1, 1956

By Robert B. Hall, Charles W. Bauer

Alunite, KA13(SO4)2(OH)6, was used from the 15th century until early in the present century as a source of potash alum and aluminum sulfate. Since early in this century its use for this purpose has declined to virtually nil with acid treatment of bauxite or clay replacing alunite as a source of alum. During the First World War alunite served as an emergency source of potassium sulfate fertilizer in the United States and Australia. More recently, alunite has been investigated as a nonbauxite ore of aluminum, with potassium sulfate and sulfuric acid as recoverable byproducts. The Soviet Union established a commercial-scale plant in the mid-1960s producing cell-grade alumina from alunitic ore and recovering byproduct potassium sulfate and sulfuric acid. Interest in nonbauxite ores, including alunite, is expected to continue in countries that presently are dependent on imports of bauxite or alumina to support their aluminum industries. The US has the largest aluminum producing and fabricating industry in the world but imports more than 90% of its aluminum-bearing raw materials. This chapter reviews the status of alunite as a potential source of aluminum with byproduct fertilizer, and the resources available to support this industry, whenever this becomes economically feasible. Historical Background Alunite has received little attention until recently, yet for centuries it held a higher place than many of the industrial minerals considered essential today. The deposits of alunite at Tolfa, northwest of Rome, were mined almost continuously from 1462 until about the middle of the present century (DeLaunay, 1907; Lombardi, 1977). The potash alum made from the alunite, called Roman alum, was a valued commodity in international trade, being used in the making of paper, in tanning leather, and as a mordant in textile dyeing. The industry at Tolfa is said to have been controlled by the Vatican and was a source of revenue for the Papal State until fairly recent times (Lombardi et al., 1977). Since early in the present century, the preferred method for making alum has been by acid treatment of bauxite, clay, or other aluminous material, so that alunite has fallen into near-total disuse as a source of alum chemicals. Appreciable quantities of mixed alunite-kaolin rock still are quarried in the Tolfa district for use by the Italian cement industry (Lombardi and Mattias, 1979), but the role of this material in the making of Italian cement is not clear. A large deposit of alunite-bearing rock in Chekiang province, mainland China, is said to have yielded a "great quantity" of alum over a period of several centuries (Yih, 1931). During the 19th century, alunite deposits in France, Spain, Australia, and other countries were exploited as raw material for making potash alum and aluminum sulfate. Interest in alunite was revived during the First World War, not for alum, but as an emergency source of potassium sulfate fertilizer. Large veins of nearly pure alunite had just been discovered on Alunite Ridge, 11 km southwest of Marysvale in Piute County, Utah (Butler and Gale, 1912), and these were quickly brought into production for making potash fertilizer to replace supplies cut off from the famous deposits at Stassfurt, Germany. An estimated 225 kt of Marysvale alunite was mined and processed at that time (Callaghan, 1973). Similarly, Australian alunite deposits were mined as a source of potash fertilizer during both world wars (Hall, 1978).

Jan 1, 1983