Search Documents

By Luke L. Y. Chang, Bert Phillips

A number of molybdenum oxides have been synthesized and their crystal structures have been described.' No data have been published on the stabilities of these oxides nor on the phase relations in the system Mo-0. It is probable that the tendency toward oxidation of both the metal and the oxides with low oxygen content in addition to the high volatilization rate of the oxides with high oxygen content have precluded accumulation of reliable data for establishing phase relations. These problems make experimentation difficult, but a modifi-

Jan 1, 1965

By Morris Muskat, James M. McDowell

A report is given of electrical analog experiments on the effect of casing perforation completions on well productivity for ideal uniform reservoirs under steady state homogeneous fluid flow conditions. Graphical results are presented for the effect of perforations of different densities and various degrees of penetration into the formation surrounding the casing or cement sheath. The latter range from perforations which terminate flush with the casing to those which extend into the formation a distance equal to the casing diameter. For the special case where the perforations terminate immediately beyond the casing with semi-spherical protrusions the electrical analog results correct and supersede previously reported theoretical calculations. It is found that the penetration of the perforations into the surrounding productive section may so increase the resultant productivity as to approach or even exceed that for open hole completions. INTRODUCTION A theoretical analysis of the effect of casing perforation on well completion, without additional penetration of the formation, was reported several years ago.' In this treatment the perforations were represented by mathematical sinks and no explicit account was taken of the imperviousness to flow of the casing in which the perforations were made. This procedure was justified by consideration of the mutual interference between the sinks, which seemed to indicate that the analytical method automatically eliminated flow across the casing radius between the perforations. However, both further theoretical investigation and the electrical analog measurements described below showed that this assumption in the previously developed theory was not valid and that the calculated well capacities would considerably exceed the correct values. § Even if this simplifying assumption were retained the generalization of the theory to situations where the perforations extend into the producing formation would be extremely difficult. On the other hand, the electrolytic model analog of this type of steady-state homogenous fluid system is, in principle, so simple that it has not been worthwhile to attempt to develop the exact analysis even for the more limited case of strict casing perforation. The whole problem has therefore been studied anew by electrical models to cover the range from holes in the casing which terminate flush with the casing surface to such as extend into the surrounding rock to a depth equal to the casing diameter. It is to be expected that the productivity of a well completed with casing radius* rw, perforated with holes of radius Tp, and extending to depths d into the surrounding rock, would depend primarily on the dimensionless geometrical parameters Te Tw TP d of the system, such as —, —, — , and —, where re is the Tw, a a rw external boundary radius and a is the mean vertical separation between the perforations. It will also depend, of course, on the number of perforation lines or total perforation density. While such parameters automatically control analytical treatments, it would require a very extensive series of model experiments to fully disclose their functional effect on the well productivity. For practical purposes, however, a rather limited range of the variables suffices to give the effects of interest. Accordingly, in the experimental study reported here the casing diameter has been kept fixed? at six in., the perforation diameter has been taken as either one-fourth in. or one-half in., their density has been varied from one to eight per ft, and their penetration into the formation has ranged from zero to six in., with a primary scaling factor of one to six. EXPERIMENTAL METHOD AND RESEARCH Although electrolytic model experiments have been made for years, there still seems to be some question as to what set of conditions will give the best results. For this reason a number of electrode materials and electrolytes were tried. Those chosen for the final experiments were copper electrodes and a weak copper sulphate solution as the electrolyte. This 'Assuming that the casing has been cemented with a uniform and impermeable cement sheath, the effective casing radius is to be interpreted as the external radius of the cement annulus. It is also assumed here that the casing is set through the complete producing section that it is perforated throughout with a uniform density and that tie formation has a a and isotropic permeability. As noted later, however, a uniform scale change permits reinterpreting the primary measurements to correspond to a casing diameter of 12 in.

Jan 1, 1950

By E. I. Larsen, E. F. Swazy, F. R. Hensel

EXPERIENCE has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. TEST MATERIALS Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It was found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended on the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as one eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from. 900°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal composition was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical properties and certain bearing properties of this alloy are described in the present paper. PREPARATION OF COMPACTS Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition: 25 per cent nickel; 7 silicon; 3 phosphorus; 64 copper. This alloy is brittle in. the cast condition and can be readily powdered. SINTERING PROCEDURE The blended powders were pressed at 25 to 40 tons per sq. in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By Wilbur T. Stuart

To assist the mining industry in attacking problems of water control, the U. S. Geological Survey has begun a program of research in mining hydrology. In certain fundamental respects water control is similar to development of water supplies from wells or to the drainage of agricultural lands, as many of the tools developed in recent years for quantitative ground-water problems are applicable, with modification, to mine-water problems. In 1952 a 30-day pumping test conducted jointly by the Eureka Corp. Ltd. and the Defense Minerals Exploration Agency provided an opportunity to gain knowledge concerning water movements around a flooded mine shaft. The methods of analyzing the data may be used as a guide for the evaluation of similar problems elsewhere.

Jan 2, 1955

By W. B. Mather

A SURVEY of the technical literature concerned with oil well drilling methods and particularly with rate of penetration by various cutting media on different types of rock provides a mass of conflicting data. This is especially true with respect to, (1) the relative efficiency of diamond, rotary and percussion drilling operations; (2) the costs of the various types of drilling; and (3) the hardness factor of various types of rock and cutting media. The latter is the particular phase of the subject discussed here. The cause of the confusion may be attributed partially to a lack of 'basic knowledge concerning the physical properties of the cutting media and of individual types of rock. It is also due in part to a general lack of uniform standards in the industry for evaluating the hardness versus drillability of rocks while possible errors in interpretation by the authors of the various papers pertaining to the subject may be an additional cause of misunderstanding. The hardness of a mineral is defined by Dana' as "the resistance which a smooth surface offers to abrasion." Webster' states that hardness is "the cohesion of the particles on the surface of a body (as a mineral) as determined by its capacity to scratch another or be itself scratched." Rock hardness, although not usually defined in publications describing rocks, is assumed to be the same as the minerals which compose the rock or the resistance of the rock to abrasion. Drillability of a rock may be defined arbitrarily as the rate at which rock is penetrated by a definite type of drilling tool with the assistance of a specific type of cutting surface or medium and under speci- fied conditions as to speed of rotation and applications of pressure. Eventually the term penetrability may have to be employed to include any method of making boreholes in rocks, since methods other than those using conventional cutting surfaces are already in operation. A case in point is the jet piercing methoda which employs an oxy-acetylene flame as a means of penetration. The word hardness as used by the drilling fraternity has a variety of meanings which depend upon the type of drilling method employed. For example, in diamond drilling, hardness is interpretated as resistance to abrasion. In percussion drilling the term implies resistance to impact or indentation, while in rotary drilling, hardness is considered anal-agous to compressive strength. The three types of hardness—abrasion, impact and compression—are conflicting variables for different types of rock. Nevertheless, the term hardness is applied indiscriminately by the industry for the resistance of rock to penetration by any type of drilling technique. Abrasion Hardness Since 1818, Moh's scale of hardness, although only relative in nature, has been accepted universally as the method of measuring mineral and therefore rock hardness. In 1933, Ridgway, Ballard and

Jan 1, 1952

By E. H. Bronson

PROPERTY of Malartic Gold Fields Ltd. is situaated in the great clay belt in the northern part of the Province of Quebec. This belt represents the floor of the glacial lake Barlow-Ojibway. The clay blanket has a gently rolling, almost flat surface, with here and there projecting knobs and ridges that outline the large irregularities of the surface on which the clay was deposited. At irregular intervals glacial eskers dominate the landscape. The ore-bearing country rock is covered by strata of clay, sand, and silt to a depth varying to 40 ft. There are serious structural problems when it is necessary to place loads of unequal intensities on this surface to support buildings and machinery for a modern mining plant. Earlier mining companies and their engineers paid little attention to the science of soil mechanics, partly because they believed it unnecessary and partly because they knew little of the subject. The results are evident in some of the tottering structures in older camps. Careful analysis of soil problems is well worth-while, since cost of foundations may vary from 20 to 50 pct of the final cost of a structure. Low operating and maintenance costs can be achieved only in this way.

Jan 11, 1957

By D. M. Deason, R. M. Chhatre, G. Y. Onoda

INTRODUCTION The treatment of colloidal suspensions is a subject of increasing interest in mining and benefication (1). Colloidal suspensions are not readily operated upon by mechanical and physical methods useful with coarse suspensions, such as filtration, thickening, and flotation. This is because colloids are strongly affected by interfacial and interparticle forces that may be large compared with, and resistant to, external forces. The degree and type of interactions between colloids can be modified by small additions of reagents such as coagulants, flocculants, dispersants, and immiscible liquids. These alterations in turn change the properties of the suspension and provide possible opportunities for transforming suspensions to a more favorable condition for a given processing operation. Phosphate slimes are an example of a colloidal system of interest today. In the mining and beneficiation of phosphate rock in Florida, slimes are a waste product. The phosphate ore (called matrix in the industry) is slurrified hydraulically and pumped to a beneficiation plant, where the -150 mesh material is removed by cycloning from the coarser phosphate rock and silica. The resulting -150 mesh slurry, called phosphate slime, is pumped to large impoundments. The solid content of the slime entering the impoundment is around four weight percent, and over 80% of the solids is less than one micron in size. The immediate problems with phosphate slime relate to their disposal (2, 3). The disposal problem is associated with the very large volumes and the poor dewatering characteristics of the slimes. To have sufficient impoundment volume, large earthen dams are built around the mined areas. The volume above ground level approaches and

Jan 1, 1980

By S. L. Craig, C. Orr, H. G. Blocker

WITHIN recent years gas adsorption methods have been developed for measuring the surface area of finely divided materials and have become extremely valuable in research on the corrosion and the catalytic activity of metals. Rather elaborate apparatus is required, and a single determination is so time-consuming that these methods have not been utilized to the fullest extent; the methods are un-suited for most routine control work such as that encountered in powder metallurgical operations and in processes employing metal catalysts. These difficulties are largely eliminated, and surface area is reduced to a routine determination if the liquid-phase adsorption of a surface-active agent such as a fatty acid can be used. When the affinity of the fatty acid carboxyl group for the solid surface is greater than its affinity for the solvent, a unimolec-ular layer of orientated fatty acid molecules will be formed at the solid-liquid interface in a manner similar to that of a compressed fatty acid film on a water surface. The measurement of surface area is then reduced to a measurement of fatty acid adsorption. This propitious circumstance, first investigated by Harkins and Gans,¹ has been employed with somewhat inconclusive results by a number of investigators in evaluating the surface properties of metals, metal catalysts, and metal oxides. The specific surface area values for nickel and platinum catalysts, determined from the adsorption of a number of fatty acids from various solvents, were found by Smith and Fuzek² to agree with values calculated by the gas adsorption technique of Brunauer, Emmett, and Teller," he so-called BET technique. And recently Orr and Bankston4 have also reported good agreement between nitrogen gas and stearic acid adsorption results in the measurement of the surface areas of clay materials. On the other hand, Ries, Johnson, and Melik5 found only order-of-magnitude agreement between these two methods in studying supported, cobalt catalysts having specific surface areas as great as 420 sq m per g; the reason is partially attributable to the very porous nature of the materials. Greenhill,6 investigating the adsorption of long-chain, polar compounds in organic solvents on a number of metal powders, concluded that a uni-molecular layer of stearic acid was formed on exposure of the solid to the acid solution and that the presence of an oxide or another film did not alter this result. Furthermore, the adsorption process appeared to be the same whether or not the sample was degassed prior to exposure to the solution. Greenhill estimated the surface area of one of the powders he investigated from microscopic diameter measurements, and obtained a rough check with surface area evaluation. Russell and Cochran7 found moderate agreement for alumina surface area results by fatty acid and gas adsorption methods. In addition, they also found that the prolonged heating and evacuating pretreatments previously used by investigators were unnecessary. The present work, however, considerably extends these previous investigations, shows that fatty acid adsorption can be used to determine the surface area of a variety of metals and metal compounds, offers further confirmation of the correctness of gas adsorption methods, and presents a simplified technique for the determination of the metal surface area which is suitable for routine work. Experimental Technique Basically, the fatty acid adsorption method is quite simple. It consists of exposing a sample of the material of which the surface area is desired to a fatty acid solution of known concentration. By analysis of an aliquot of the solution, the concentration after adsorption has occurred may be determined. The difference between the initial quantity of acid in solution and the final quantity is that quantity of acid adsorbed by the sample. The specific surface area of the adsorbent material may be calculated from the quantity adsorbed and the weight of the sample. In agreement with the findings of others as outlined above, it was found entirely unnecessary to degas or pretreat the nonporous materials employed other than by drying them thoroughly. However, precaution was necessary so that the dried sample entered the fatty acid solution with little exposure to moisture. The effect of moisture on the interaction of stearic acid with finely divided materials has been thoroughly investigated by Hirst and Lancaster." They found the presence of water merely reduced the amount of acid adsorbed by powders such as TiO2, SiO2, Tic, and Sic. With reactive materials such as Cu, Cu2O, CuO, Zn, and ZnO, however, water was found to initiate chemical reaction. Only with ZnO was reaction observed when the solid and the solu-

Jan 1, 1953

By R. S. Schechter, T. R. Guilinger, P. Bobeck, J. G. Price, L. W. Lake

This paper presents the results of an experimental study on the rate of uranium and molybdenum extraction from a flow reactor. Specific variables tested are fluid throughput and flow rate, lixiviant cation, and injected pH and carbonate concentration. The ore tested was from the Felder mine in southern Texas. It contained substantial quantities of marcasite and molybdenum disulfide that competed with the uranium ore for oxidant. Flow studies showed the oxidation of molybdenum disulfide under field conditions is mass transfer controlled, whereas the uranium oxidation is limited by surface reaction rate. The rate of uranium oxidation decreased with decreasing pH. The total carbonate levels, on the other hand, were unimportant. Ammonium carbonate appears to greatly decrease, if not completely halt, the reaction of marcasite with the oxygen. This effect was not found using either sodium or potassium carbonate.

Jan 1, 1986

By P. H. Delano, Will H. Coghill, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By Will H. Coghill, P. H. Delano, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By Emmanuel Detournay, Charles Fairhurst

A method is proposed for computing (a possible solution of) the ground reaction curve, for use in tunnel support analysis, in cases where the initial stress field is not hydrostatic. Rock around a circular tunnel is assumed to behave as an elasto-plastic material with a Mohr-Coulomb yield envelope.

Jan 1, 1982

By C. W. Washburne

THE waters of many oil fields have been regarded as buried sea water which has been retained in the sediments since the time of their deposition. The preservation of connate water through geological time has seemed improbable to only a few geologists, but there is room for doubt that buried sea water could remain in the strata during their periods of deformation and during the many subsequent epochs of. the circulation of meteoric ground-water. Some have even suggested that the calcium chloride water in the deep mines of the Lake Superior region is ancient sea water buried in the Algonkian lavas, but it is hard to understand how such water could be derived from the highly sodic and sulphatic water of the sea. It would seem more plausible to connect the calcium chloride with the highly calcic magmas of the greenstones in which it is found. Chemical analyses of waters associated with oil differ widely from the composition of sea water, requiring extensive alteration of the latter, if the former is truly its derivative. The first notable difference is the general absence of sulphates from oil-field waters, but this has been explained satisfactorily through reduction by hydrocarbons and organic matter. Oil reduces sulphates with the production of hydrogen sulphide (or sulphur), water, and carbonates (or carbon dioxide). The second striking difference is in the high ratio of chlorine to sodium. An examination of the analyses of chloride waters from oil fields shows that they contain a large relative excess of chlorine over that in sea water. Moreover, there is difficulty in finding chemical reactions that are probable in nature, by which sea water could be converted into anything like the chloride waters of oil fields. In the latter a large part of the chlorine occurs as calcium acid magnesium chloride. This condition might be produced by the removal of sodium carbonate, which; however, cannot be precipitated in the presence of much calcium or, magnesium.

Jan 3, 1914

By Joseph Hodgson

IN 1880, mining operations were commenced at the Copper Queen mine. The famous Queen orebody, which extended to the surface, was first quarried from a large open cut in the outcrop. The orebody was followed down to the 300 level with the Queen incline, and stoped. This, we believe, marks the introduction of square setting in the Bisbee district, which is still the method most generally used. Orebodies The orebodies in the Copper Queen mine occur in the limestones, and the main portion of the ore has been mined from the Abrigo, Martin, and. Escabrosa limestones. While the orebodies outcrop in the extreme western end of the mine, the general dip is to the east and south, at an angle of about 20°, although this dip is not by any means regular, being, in fact, very irregular locally. The ore is remarkable for its variableness in character, some of it being very soft, requiring a large amount of timber, and other portions consisting of extremely hard sulphides. The orebodies, in general, While remarkable for their continuity, are very irregular, both as to shape and size. The mine having been in operation so many years, and mining having been prosecuted over such a large area, the operations have caused the shrinkage of the overburden, and there is a constant movement, which is shown y large cracks and interstices in the surface rocks, which largely contribute to the very high deadwork or maintenance cost of the mine. It is surprising that for year 1913 it cost almost $400,000 just for the one item of repairs and deadwork in this property.

Jan 8, 1914

By Neil H. Cole

Cost and price inflation and financial gearing through loans are characteristic of modern resources projects. Conventional discounted cash flow and 1P.R analyses, in real terms, and without financing, have inadequacies which can yield misleading results. The degree of improvement in value for project equity owners is limited to the value of the additional tax benefit accorded through the financing instrument used. Debt financing may be low in price and value, but its priority means that the equity owners assume a higher risk, thereby increasing the cost, or price, of their capital. The cost of equity capital, or investment hurdle rate, is related to the Capital Asset Pricing Model. Distortions do occur, with inflation, due to depreciation effects, which can cause the adoption of misleading project rate of return or hurdle rate criteria. For investment decisions, the greatest accuracy possible in forecasting is essential, especially for inflation rates,

Jan 1, 1985

By L. G. Huntley

Introduction IN View of the recent advance made in the knowledge of the nature and conditions accompanying the occurrence of oil and gas, and of the recent activity in drilling in Wyoming, Montana, and western Canada, a discussion of the probabilities of obtaining production in such a reservoir as the Dakota sand in general, and in particular districts, is thought by the author to be timely and likely to result in more intelligent operating in certain parts of the territory underlain by this sand. In Canada particularly it is thought that these general considerations have equal if not more significance in a consideration of the oil and gas possibilities of the formations than have the various local conditions.

Jan 6, 1915

By Arthur L. Flagg

The Elk City mining district of Idaho occupies a position near the geographical center of Idaho county, a region of moderate elevation in the western foot-hills of the Bitter Root mountains. The district comprises an area of approximately 350 Sq. miles, bounded on the west by the Newsome district and on the south by the Dixie and Oro Grande districts. There are no mining districts to the north or east. Elk City, the principal town and the seat of the mining office for the district, is situated in a hydrographical basin surrounded by low hills. The elevation is 4,200 ft. above sea-level. Through this basin flow Elk Creek, Red river, and American river, which unite west of town to form the south fork of the Clearwater. The one township is set out from the Bitter Root Forest Reserve. Though a railroad starting from the Stites terminus of the Clearwater Short Line of the Northern Pacific railroad has been under consideration for some years, the camp is yet without railroad facilities. The projected road would follow the south fork of the Clearwater on easy grades, but would be very expensive to build and maintain. While such a road would greatly benefit those who are now operating in the camp, and in a sligh degree stimulate interest in its possibilities, there is hardly business enough to warrant its construction. At present all supplies and equipment are hauled in by wagon from Stites, a distance of 58 miles, over a wagon road constructed by the State in 1904, following in the main the old Nez Perce trail. While this is not a bad road, it is not all that might be desired. Starting at Stites at an elevation of 1,327 feet above sea-level, the road runs through low hills to Clearwater, a distance of 10 miles. In the next 16 miles the climb is steady until the Mountain House is reached, which is near the summit of Mount Pisgah. This is the highest point passed on the road, having an elevation of 6,500 ft. From the

Jan 1, 1914

By William Ian Wark, Alwyn Birchmore Cox

DIFFERENT parts of the world in which mineral separation by flotation is practiced experience vastly different natural temperatures, and in some districts there is a big difference between summer and winter temperatures. It will be shown in this paper that the temperature is of considerable importance where it is desired to separate pyrite or arsenopyrite from other minerals. It is probable that some of the differences obtained in the flotation of these minerals at plants working under otherwise similar conditions are due to temperature variations. The influence of temperature on the flotation of galena, chalcopyrite and sphalerite by xanthates is less marked than its influence on pyrite flotation. EXPERIMENTAL METHOD The methods used have been described previously.1-4 In each test the clean mineral specimen was immersed in a solution prepared by adding the reagents in the following order: (1) sodium carbonate and hydrochloric acid as necessary to buffer the solution and to give approximately the pH value desired, (2) sodium cyanide, (3) copper sulphate, (4) ethyl xanthate, followed by (5) a final adjustment of pH value. After ½ hr. the mineral was tested for a xanthate film by bringing a bubble of air into apparent contact with the submerged polished surface. If true contact (spreading) was not obtained within ½ min. and after cleaning the surface by wiping with a small linen pad, it was concluded that the adsorption of a xanthate film had been prevented. Following the method already described (ref. 2), curves have been constructed such that for a solution ' composition corresponding to any point below the curve, contact between mineral and air is possible, whereas for a solution composition corresponding to any point above the curve, contact is impossible.

Jan 1, 1938

By Willard S. Morse

The purpose of this paper is to record the results obtained in the use of the Russell process at Aspen, Colo., covering a period of fourteen months, from November, 1891, to December, 1892, during which time over 30,000 tons of ore, purchased outright, on sample and assay, were treated. No explanation of results will be attempted, nor will the chemistry of the process be discussed. The plant was designed by C. A. Stetefeldt, of San Francisco, and built by the owners by day-labor. The entire plant is run by water-power, supplied by a flume 3600 feet long, and a pipe-line 2200 feet long, with a head of 170 feet. A Pelton water-wheel, 8 feet in diameter, is used, from which power is transmitted by wire-rope to the main counter-shaft in the mill, a distance of about 250 feet. From the mill to the samplingworks, about 150 feet, power is also transmitted by a wirerope. A Pelton water-wheel, 3 feet in diameter, supplies power to the dynamo for lighting the plant. The works are located adjoining the Santa Fe railroad tracks, and all ore and supplies are unloaded directly from the cars to the works. The sampling-works are provided with crushers and rolls, the latter being used only on samples, and not on the entire ore. The Cornish hand-quartering method is used in sampling ore for purchase. After crushing and sampling, the ore goes to the bedding-floor, where it is made up into mixtures suitable for the mill. The drying-plant consists of four Stetefeldt double shelfdryers, six shelves high, and is provided with dust-chambers and a stack 65 feet high for draft. These dryers are fired with gas

Jan 1, 1896

By E. B. Snyder, H. M. Kraner

This paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, partitularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercia1 blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. Factors Affecting Choice of ._ Refractories If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing tempera- . ture, which he in turn internrets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and re-. sistance to the action of slag. In most refractory applications . several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient Stages and the Progress is determined by measuring slight changes in porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures at which they are to be used, although in many cases it would be desirable from the user's point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. Both may occur in the same refractory containing two such clays.

Jan 1, 1944