Search Documents

By E. A. Jones

THE Southeast Missouri division of the St. Joseph Lead Co. normally hauls and hoists over 5 million tons of lead ore each year. This ore is mined in the stopes and headings of 20 mines, hauled to a main line system, see above, and transported up to 6.4 miles to ore-hoisting shafts. Average haulage distance is 2.16 miles. A few years ago a distinguished mining engineer visiting this area for the first time remarked, "You do not have a mining problem; yours is a haulage problem." Its relative importance may be gaged by the fact that mine haulage represents about 25 pct of the total cost of mining ore, the most costly single underground operation. The Southeast Missouri lead belt is a mining district located about 65 miles south of St. Louis. This district is roughly 6 miles wide and 10 miles long. The ore horizon lies about 400 ft below the surface where most of the ore is mined from flat-lying beds of dolomitic limestone. This paper deals with the central part of the district, namely, that portion which contains a group of interconnected mines all in a central haulage system, serving four hoisting shafts. The two major hoisting operations are carried out at Federal No. 17 shaft and Leadwood No. 12 shaft. No. 17 accounted for about 70 pct of the ore hoisted in the district during 1950, averaging about 14,000 tons per operating day. The underground dumping and skip-pocket system at this shaft is similar to those of the other shafts except that it has two rotary dumps. The other ore-hoisting shafts have only one. It might be mentioned that waste rock is hoisted at still other shafts, hauled off, and dumped on the surface by trucks. The hoisting shafts are on a connected system of about 200 miles of underground 24-in. gage main line railroad. There is also the Bonne Terre system, with its own ore-hoisting shaft, which consists of 13.5 miles of 24-in. gage main line, located in the extreme north portion of the lead belt area. Smaller outlying mines such as Doe Run No. 12 and Hayden Creek operate on trackless or shuttle car haulage. In addition to the system of main line haulage, each contributing mine group has its own extensive system of stope or heading railroad. Trackless mining is making considerable headway in the Lead-wood and Desloge mines. Here the shovel loads into a shuttle car which in turn dumps into mine cars spotted on the main line track system. When the merits of underground haulage and surface transportation are compared, it must be remembered that in early days there were many individual

Jan 1, 1954

By David W. Mitchell

WHILE pure magnesium does not corrode rapidly the presence of even very small quantities of certain other metals accelerates corrosion remarkably. Because magnesium is such an electropositive metal (E° = +2.34 volts)' the presence of substances that permit galvanic activity is extremely undesirable. It is stated that as little as 0.017 pct of iron in magnesium causes a marked increase in the corrosion rate.2 Magnesium and its alloys are commonly melted in iron or steel pots; consequently the commercial metal has the opportunity to pick up iron if it has that tendency. Quantitative data on the solubility of iron in magnesium are of practical as well as of academic interest. Some magnesium alloy castings tend to have large grain size unless suitable treatment is given to the liquid metal just prior to casting. One method of grain refinement consists of "superheating" the metal just prior to casting. "Superheating" is heating to a temperature 100 to 200°C above the casting temperature and holding for a short period of time. Superheated metal has a much finer grain than unsuperheated metal. A satisfactory explanation of this phenomenon has not been forthcoming. One hypothesis attributes the grain refinement in the superheated metal to precipitation of some phase that is miscible at the temperature of superheat but not miscible just below the casting temperature and which is thought to provide nucleating centers for crystallization. This phase, if the foregoing hypothesis is correct, would probably be a metal or an intermetallic compound. Of the metals likely to be found in magnesium alloys, iron is one of the most likely candidates for the role of grain refiner for iron occurs in small quantities in all commercial magnesium and magnesium alloys. A. Beck' states that magnesium, in either the liquid or the solid state, cannot dissolve iron and that iron exists as a finely divided suspension which does not settle out because of its extreme fineness. Beck also presents a micrograph showing a large iron dendrite in magnesium but does not comment on the crystallization of iron from a solution supposed to contain none. It is doubtful that dendrite formation from suspended iron would be possible. This suspension theory is the basis of patents4 covering the removal of iron from magnesium by allowing the iron particles to act as nuclei for the formation of primary magnesium crystals which can be separated by segregation. Also covered by patents is the removal of iron by the addition of another metal to form an intermetallic compound with the iron which, because of its increased particle size, is able to settle out of the molten metal. Here, too, quantitative information on the extent of iron solubility in liquid magnesium is of more than theoretical interest. M. Hansen,5 in his critical collection of the data on binary alloys, states that iron is not soluble in liquid magnesium. W. R. D. Jones6 who studied the physical properties of low iron magnesium alloys observed a

Jan 1, 1948

The most extensive oil shale development program ever undertaken in the United States has been that carried out by Colony Development Operation at Para- chute Creek in western Colorado. Field development goals were completed this spring, with the remainder of the $24 million joint venture program, primarily engineering, environmental and economic analysis, due to be finished by the end of 1972. Upon completion of the overall program, a decision concerning a commercial venture is expected. This program points up the increasing attention being focused on oil shale as a source of crude oil and energy for the U.S. at a time when the nation's supply of oil produced by conventional methods is far from adequate to meet the demand. The oil shale reserves of the Green River formation in Colorado, Utah and Wyoming are the largest hydrocarbon reservoir. The Piceance basin of Colorado, alone, contains some 80 billion bbl of shale oil recoverable by modern methods in reserves more than 30 ft thick and containing at least 30 gal of oil per ton. The U.S. Geological Survey has estimated that the total shale oil reserves of the Green River formation in the states of Colorado, Utah and Wyoming is more than 600 billion bbl of oil in deposits containing at least 25 gal per ton of shale oil.

Jan 10, 1972

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

The tensile properties, creep resistance. and thermal stability of highly alloyed Ti-Al-Zr alloys were examined. On the basis of these studies, the Ti-7Al-1ZZr composition was selected for more complete evaluation. The alloy was found to be weldable and free from excessive directionality. In addition, it developed maximum properties without requiring heat treatment other than an annealing operation in the alpha field. The alloy was recommended for scale up and is presently being investigated on a production-level basis. One of the more attractive properties of titanium alloys is their ability to withstand stress at moderately high temperatures, and a considerable amount of effort has been devoted to increasing the maximum service temperature of titanium alloys. This work has suggested that the optimum alloys for high-temperature service will be single-phase a (close-packed hexagonal) alloys containing significant amounts of aluminum. However, the maximum amount of aluminum which can be alloyed with titanium is between 6 and 8 pct,l since at high-aluminum contents an embrittlement reaction occurs in the anticipated service temperature range, 800" to 1100°F. It has been shown that the embrittlement reaction involves decomposition of the high-aluminum a phase to one or more new phases.' Since this reaction does not occur at intermediate or low-aluminum contents, it was felt that intermediate Ti-A1 alloys might be strengthened by a-soluble ternary additions without inducing the embrittlement reaction. The first alloying addition considered was tin, which shows extensive solubility in a titanium and has moderate strengthening tendencies. Unfortunately, it was soon apparent that tin also promoted the embrittlement reaction, and that to obtain a stable alloy, the aluminum content had to be reduced as the tin content was increased. The second alloying addition considered was zirconium, which is similar to tin in its effects on titanium. This element did not contribute to the embrittlement reaction and, in fact, appeared to increase the maximum amount of aluminum which could be alloyed with titanium without inducing instability. This paper describes an investigation of the Ti-A1-Zr a alloy region. Alloys containing from 4 to 12 pct A1 and from 6 to 15 pct Zr were examined. The properties of these alloys are described and the bases for selecting an optimum composition is outlined. This composition, Ti-7A1-12Zr, is presently being scaled up in tonnage quantities, and is being evaluated extensively throughout the industry. In addition to presenting the basis for its selection, this paper presents a description of the properties developed in laboratory material as determined during the alloy investigation. These properties suggest that this alloy can fill an important position in applications requiring light weight, fabrica-bility, weldability, and strength to 1000oF or higher. EXPERIMENTAL PROCEDURES Titanium alloy ingots were prepared by inert electrode arc melting under an argon atmosphere. Alloying elements used were 110 Bhn titanium sponge, high-purity aluminum, and reactor-grade zirconium. Pancake-shaped ingots were prepared weighing approximately 300 g. The composition of the ingots was checked by weight measurements before and after melting. The pancake ingots were forged at 2000°F to approximately half their original thickness to give a flat plate roughly 1/2 in. thick. This plate was then rolled at 1800' to 1600°F to 0.250 in. thick. All of the alloys examined fabricated well. However, alloys containing 15 pct Zr tended to overheat due to exothermic oxidation, and scaling was excessive. As might be anticipated from its effect in decreasing the ß transus, increased zirconium appeared to improve fabricability somewhat, especially during rolling at lower temperatures. Except for a limited study of heat-treatment response, all alloys were examined in the a-annealed condition. Prior to heat treatment the a and ß tran-sus temperatures were determined by metallo-graphic examination of samples quenched after annealing at 50-deg intervals in the transformation region. These data are shown in Fig. 1. Recrystal-lization appeared to occur in about 1 hr in the range 1300º to 1500ºF. Therefore, alloys were annealed for 1 hr at 1550ºF (4 and 5 pct Al), 1600ºF (6 through 7-1/2 pct Al), or 1650°F (8 or more pct Al). This produced an equiaxed a grain structure. In most alloys, a "ghost" structure was visible after the a-annealing treatment, as shown in Fig. 2. This structure apparently resulted from the acicular

Jan 1, 1963

Wartime geological studies by the U. S. Geological Survey and subsequent drilling carried on by the Bureau of Mines disclosed new ore in the Illinois-Wisconsin zinc field. As a result, several companies are carrying on drilling programs to locate and define new ore bodies. The Vinegar Hill company, which operates a custom mill to handle ores from various sources, now employs about fifty men in production at their Andrews mine. The ore is usually found in a 200-ft horizon below the surface. Water problems are not serious. Commercial-grade ore ranges up to 8 and 9 per-cent zinc and the cut off is approximately 41/2 percent.

Jan 1, 1948

By T. D. Murphy

This chapter deals with those types of silica raw materials that have been segregated and refined by natural processes into nearly monomineralic deposits and hence, by virtue of their high degree of purity, have become the sources of commodities having special and somewhat restricted commercial uses. In some instances, these raw materials occur in nature as unconsolidated quartzose sand or gravel and can be exploited and used with very little preparation and expense. More often, they occur as sandstone, conglomerate, quartzite, quartz mica schist, or massive igneous quartz which must be crushed, washed, screened, and sometimes chemically treated before commodities of suitable compositional and textural characteristics can be successfully prepared. The occurrence and distribution of silica raw materials is summarized and an effort has been made to bring commodity definitions, critical properties, and specifications up to date. Presentation of mining and processing methods is considered beyond the scope of this article; they are, for the most part, conventional and well known. New production techniques are currently reported in the trade journals and are later adequately described in technical publications as promptly as competitive restrictions allow. Discussion on Basis of Use ABRASIVE USES Industrial silica used for abrasive purposes falls into three main categories: (a) blasting sand; (b) glass-grinding sand; and (c) stone-sawing and rubbing sand. Blasting sand is a sound closely-sized quartz sand which, when propelled at high velocity by air, water, or controlled centrifugal force, is effective for such uses as cleaning metal castings, removing paint and rust, or renovating stone veneer. It is commonly referred to as Sand Blast sand. Multicycle quartz sand is an efficient blasting agent by merit of its survival characteristics which are soundness, toughness, and hardness. Steel grit and shot have supplanted it to a large extent but owing to their higher cost and tendency toward deterioration in storage, are still not universally used. It is conceded that angularity promotes faster cutting but this is offset by a higher loss in fines. The peening action of a rounded grain is a desirable feature in achieving a satin finish for certain light metal castings but a subangular grain is unsurpassed for fast heavy cutting. Specifications are chiefly based on size frequency distribution but it is mandatory that the grain be free of adhering clay or irony coatings. Material that dusts upon handling will not be tolerated. There is no uniform trade designation for the many blasting sand grades. Most producers sell on the basis of numbered grades; that is, No. 1, No. 2 and so on, this generally connoting fine to coarser grades. Designation of grade by the two sieve sizes between which most of the material lies, is practiced in some areas. Thus, in a No. 1220 grade, 98 pct of the material passes a 12 mesh sieve and is retained on a 20 mesh sieve. Blasting sand specifications vary according to use. Coarse grades range from 4 mesh to 12 mesh, medium grades range from 12 mesh to 30 mesh, finer grades may range from 20 mesh to 100 mesh or finer. Specifications generally call for narrow limits of gradation, requiring precise sizing methods. The fact that most blasting sands are retained

Jan 1, 1960

By R. H. McLean

Jet impingement produces two mechanisms to clean the bottom of a borehole during jet-bit drilling operations. One is an impact-pressure wave in the immediate area of jet impingement. The other is crossflow, which spreads across the bottom away from the pressure wave. Measurements of the vertical distribution of the cross-flow at several positions beneath a 4 3/4-in. tricone jet bit in a laboratory model show that the maximum velocity in the crossflow is directly proportional to the square root of the product of the rate of flow and the velocity of the jets through the nozzles (QV). Other measurements in the laboratory model show that gradients in the impact-pressure wave are directly proportional to the jet QV if the diameters of the nozzles are held constant. Consistency of the basic relationships through changes in the Reynolds numbers of the jets from 31,000 to 93,000 suggests that the laboratory results should be representative of typical flow in field operations having higher Reynolds numbers. Estimates of the impact-pressure waves under conditions other than those in the jet-bit model may be made by comparison with a less complex model—impingement of a jet against an unrestricted flat surface normal to the jet. Equations derived from current jet technology describe the wave in this simple system for a wide range of conditions. INTRODUCTION The efficiency of rotary drilling operations is strongly linked to the efficiency with which cuttings are removed. Cuttings remaining on the bottom of the borehole will impede further penetration by the bit until they are removed. Wasteful regrinding is prevented if the fluid circulated past the bit removes cuttings as rapidly as they are made. Most investigations of bottom-hole cleaning under bits have been concerned with the rate-of-penetration effects of bit type, nozzle configuration, fluid properties, pressure gradients and utilization of hydraulic horsepower. These investigations have shown that drilling muds, weighted to keep the pressure in the borehole greater than in adjacent formations and carrying material which forms a filter cake, apparently plaster cuttings against the bottom, making them difficult to remove. In addition to a demonstration of the factors causing poor cleaning, the most significant result of these previous investigations has been the increased use of jet bits accompanied by better hydraulic programs and better selection of drilling fluids. Undoubtedly, these practices have improved bottom-hole cleaning, but rates of penetration when drilling with muds are still often lower than would be expected with perfect cleaning." Although there is general agreement with the concept that increasing hydraulic energy at a jet bit often increases the rate of penetration by improving cleaning, research workers have differed as to the best criterion for evalyating hydraulics. Some lean toward maximizing the product of the rate of flow and the velocity through the nozzles (QV) others prefer to maximize the hydraulic horsepower at the bit;'"-' "till another says that neither criterion is universally suitable."' This controversy shows that conclusive field evidence has not established the superiority of either of these criteria. Analysis of the fluid flow which cleans the bottom should contribute to resolving the controversy. Impinging jets clean the bottom by creating two mechanisms capable of dislodging cuttings. One is the impact from the momentum of the jet and the other is the flaw parallel to the bottom away from the area of impingement. The impact force appears in the form of a pressure wave on the bottom and, in this paper, is called the impact-pressure wave. The flow parallel to the bottom is called crossflow. Fig. 1 illustrates these two mechanisms. This paper describes crossflow and the impact-pressure wave beneath jet bits and relates them to controllable parameters. Through these relations, criteria for use in designing hydraulics to achieve maximum use of the mechanisms of cleaning are derived. PROPERTIES OF CROSSFLOW CONCEPTS DEVELOPED IN PREVIOUS INVESTIGATIONS Concepts of scavenging the bottom by crossflow have been well discussed by Bobo, et al." They examine the means by which crossflow may create forces on cuttings and conclude that the cleaning action of crossflow can be increased by increasing the velocity of the flow stream close to the bottom. Using boundary layer theory, they indicate that a reduction in the viscosity of the drilling

Jan 1, 1965

Alpha Portland Cement Co.'s mining operations at Manheim W. Va., produce 750,000 bbl of limestone yearly, averaging 2200 bbl per working day. Thirteen parallel entries have been driven to date, each almost 30 ft high and about 45 ft wide, extending back 5000 ft to the working faces. Pitch of the seam from the lowest to the highest entries is steep enough to provide excellent year- round natural ventilation, and this, together with the size of the entries and a good bottom, has allowed face crews to drive right up to the working areas in the family car.

Oct 1, 1956

By C. E. Wood

THE Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1939

By Gerald Edmunds

Although the phenomenon of season cracking is still imperfectly understood, there seems to be ample evidence that season cracks are propagated by the combined action of corrosion and a stress of either internal (residual) origin or external origin. The factors that influence season cracking may therefore be grouped according to corrosive media, nature of stress, and character of the material. Thus the important mass of evidence pointing to ammonia as the most frequently active corroding agent causing season - - cracking of brass has naturally led to the development of laboratory tests of a moderately accelerated character based upon ammonia together with auxiliary agents such as air, water vapor, and carbon dioxide as the corroding agent. Similarly, the knowledge that stress must be present has led to the use of externally applied and therefore accurately measurable stresses in laboratory testing. A companion paper(^)^ to the present one discusses the development of these test methods in our laboratories. The present paper discusses data bearing on factors concerning the nature of stress such as its magnitude and direction of application. It also deals extensively with the character of the brass, particularly in regard to the copper-zinc ratio and the structure as developed by mechanical work-

Jan 1, 1945

The early records of coal in Kentucky by Walker and Gist have already been mentioned. Thomas Hutchins was aware of it in 1778, or perhaps several years earlier, as in writing of the Buffaloe, now Green, River, he said, "several persons who have ascended this River, say, that Salt Springs, Coal, Lime and Free Stone etc. are to be found in a variety of places."1 The next record found is an entry to Ellis and Marshall, of 878 acres on Coal Bank Creek, in the, then Fayette County on July 14, 1784.2 The settlement might have been made, or the name given, some time before. Hermeline, in 1783, mentioned iron ore and coal on the Green River,' although he had not been west of the Susquehanna River; his knowledge of coal might have come from Hutchins, although the latter made no mention of iron in that locality. In November 1790, coal was mined on Sturgeon's Creek in Lee County and floated in three barges down the Kentucky River to Cleveland's Ferry, where it was hauled to Lexington. The results were not equal to the expectations, and it was 1793 before the experiment was. repeated 4 In 1791, the estate of Samuel Wharton advertised for sale 31,000 acres "in the county of Jefferson, on the North Side of the Green or Buffaloe river, in the State of Virginia."5 In November 1795 three patents were issued for land in the then Lee County, aggregating 130,000 acres. These patents cover much of Harlan County. The descriptions of these surveys mention passing stone coal. on Rough Branch of Martin's Fork, a "great deal of stone coal" on Blacksnake Branch of Pucketts Creek, and "a quantity of stone coal" probably on Crummies Creek.6 Jedediah Morse, in The American Gazetteer, 1798, said that in Kentucky "in many places there are appearances of potter's clay, and coal in abundance." It is possible that shipments may have been made from near

Jan 1, 1942

By J. Tarwater

The torsional testing of cylindrical medium-carbon steel specimens, heat treated to a high strength level, revealed a stress-strain relationship that was dependent on the direction of torsional plastic pre-strain. This Bauschinger effect was observed in prestrained specimens both with and without subsequent elevated-temperature strain aging. Yield stresses in strain-aged specimens exceeded those of simply prestrained specimens and the difference in stress was greater when the prestrain direction opposed the test direction. This behavior is discussed in terms of the classical dislocation pile-up using Cottrell's equation, A plastically prestrained strain-hardenable member, loaded in a direction opposite to the direction of prestrain, produces a stress-strain relationship differing appreciably from the curve representing reloading in the prestrain direction. This phenomenon, referred to as the Bauschinger effect, will be discussed in terms of the stress differences ob- served at a specified strain. The effect, dating back to the 1880's, was first attributed to grain boundary stresses. When later work revealed that the effect was also present in single crystals, revised theories attributed the diminished applied reverse stress to assistance from internal long-range stresses. These stresses have been associated with dislocation pile-ups or with dislocation arrays having analogous stress patterns. The stress patterns are subject to alteration by interaction with interstitial solute atoms and acceleration of the interaction may be accomplished with elevated-temperature strain aging. As discussed herein, the interaction showed a directional effect with regard to the applied stresses necessary for small plastic strains. Aside from the rigorous Bauschinger stress-strai relationship, which compares prestrained members, it is interesting to compare the stress-strain curve of a member being prestrained with that of a prestrained member being reverse loaded. For small strains which are a fraction of the prestrain deformation, the applied stresses of the reverse reloaded member are smaller. However, as the reverse strain approaches the prestrain value, the stresses approach equivalence. It has been reported1 that the stress required to return a prestrained specimen to its initial "zero" position generally exceeds the prestrain stress because of the work hardening occurring on potential slip systems during prestrain.

Jan 1, 1963

By Robert U. King, John W. Vanderwilt

THE Climax molybdenite deposit in Lake County 100 miles southwest of Denver is located in the central part of the mineral belt extending north-easterly across the state. Principal geographic features and geology are shown on Fig. 1. The first period of molybdenite mining, which began in 1918, ended in April 1919 because of limited demand and a price drop to about 724 per lb. During this time the ore came from the Leal level and surface outcrops at a higher elevation. Rate of mining was 250 tpd and several million tons of ore averaging 0.7 pct molybdenite were developed. Since April 1924, when the second period* began, Climax Molybdenum Co. has been the only operating company. Production in 1924 was 400 tpd and finding ore was a continual problem. When the White tunnel was extended, however, further ore was encountered. The orebody was thought to be tabular until 1926, when B. S. Butler recognized the relation of the developed ore on the Leal and White levels to a central area of fine-grained hydrothermal quartz, and by 1929 diamond drilling had blocked out indicated ore reserves in excess of 100 million tons.

Jan 1, 1955

By J. Gordon Parr, D. H. Polonis

High purity alloys of titanium and iron, made by a technique of levitation melting, have been investigated with particular reference to martensite formation and decomposition in the hypoeutectoid range. A preliminary study has been made of the occurrence of the phase corresponding to the structure Ti2Fe. MANY of the previous investigations of Fe-Ti alloys have been made using Kroll sponge as a source of titanium; and the subsequent heat treatments to which alloys have been subjected has, on occasion, led to further contamination. Worrier,',' who suggested a part of the equilibrium diagram for the binary system, and Wallbaum and coworkers,3-5 who worked largely with iron-rich alloys, all used Kroll sponge. Van Thyne, Kessler, and Hansen,6 in their determination of the equilibrium diagram, used iodide titanium for alloys up to 30 pct Fe. Duwez,7 who measured the M. temperature of titanium binary alloys with many solute elements, used iodide titanium in all cases except in his work on Ti-Fe alloys for which he used Kroll sponge. The investigation of the supposed phase Ti2Fe by Rostoker8 nvolved the use of iodide titanium. A section of the constitutional diagram, after Van Thyne et al., is reproduced in Fig. 1. Frequently too much stress is placed on the effect of contaminants in equilibrium and nonequilibrium systems, but there is no doubt that titanium alloys are extremely susceptible to interstitial atoms. Consequently, the main purpose of the work to be described was to determine those features of phase transformations in pure Ti-Fe alloys that were considered of importance in commercial heat treatments. For, although commercial alloys may not be of high purity, the investigation of a system uncomplicated by traces of impurity is a desirable starting point. Another incidental feature, the occurrence of Ti2Fe, was also investigated. The entire study was carried out using powders obtained from alloy ingots, for diffusion reactions are often more rapid in small particles than in bulk specimens. The frequently adopted practice of ascertaining phase constitutions by X-ray analysis of powders, and relating these to the microstructures and mechanical properties of bulk specimens, is considered by the authors to be open to criticism. In the martensite reactions in the Fe-Mn system, for example, it has been shown- hat similar phase distributions in solid and powder may result in different hardness values and appearance under the microscope; and it is possible that similar anomalies might occur in the Ti-Fe system. Consequently, in order to

Jan 1, 1955

By R. Maddin, S. K. Tung

SUCCESS of the dislocation theory in formulating the transitional lattice theory proposed by Har-greaves and Hill in 1929' is well established for low angle grain boundaries. The theoretical work of Burgersa and Read and Shockley,3 together with the experimental observations of Aust and Chalmers4 and Parker and colleagues,6 leaves little doubt as to the structure of grain boundaries with differences of orientations up to between 15" and 20". Beyond these angles, the structure of the boundary is not so clear, and is still a matter for conjecture. There have been notable experiments devised from which the data could be used to calculate energetics for possible arrangements of atoms in forming a large angle boundary.6 Most of these experiments deal with diffusion through and along the grain boundary. The recent work of Rhines and Cochart7 and Rhines, Bond, and Kissel18 was concerned with the relative movement of grains in aluminum bicrystals under constant tensile loads with their boundaries aligned at 45 " to the tension axis. The gliding along the grain boundary was cyclic and began after an incubation period. The velocity of gliding increased with the sum of the angular difference, 8, between the operative slip direction in the conjugate crystals and the angular difference between the active slip planes as measured between their traces upon the grain boundary. The initial gliding rate varied with temperature, and the logarithm of the average gliding taken over a considerable period was a linear function of the reciprocal of the absolute temperature: the slope gave an activation energy of 11,000 ±1,000 cal per mole. Since the rate of grain boundary shear is sensitive to the misorientation of the grains themselves, as shown by several workers,7,8 it is suggested that further work of this type might be fruitful in adding information regarding the behavior of boundaries under stress. The techniques devised by Chalmers" added impetus to the facility for observing grain boundary behavior, in that they provided a simple means for producing bicrystals of predetermined orientation so that the angle of the boundary could be controlled,

Jan 1, 1958

By D. B. Kibler

THE Florida hard-rock field extends from Suwanee and Columbia Counties in northwest Florida to south of Croom, Florida, in Hernando County. This area is approximately 100 miles long and varies from 2 to 30 miles in width. Florida hard-rock phosphate was discovered at Hale Springs, about one mile northwest of the town of Dunnellon, Marion County, in the year 1888, by Albertus Voight, who lived within a few hundred yards of the spring. Soon after this discovery there was a great influx of land speculators and wildcat operators into the vicinity of Dunnellon. A few years later phosphate was found in Alachua, Levy, Citrus and Hernando Counties, and a great number of small crude plants were built from Newberry, Alachua County, all the way to Croom, Hernando County. Phosphate was found in many places as "outcrops." Looking for outcrops was the first method used by the early prospectors in searching for deposits. Several years passed before any systematic method of prospecting was used. EARLY MINING The early method of mining hard-rock phosphate was with picks and shovels, wheelbarrows, mules and wagons. The pick-and-shovel method was used altogether until about 1900, when some of the larger operators began to use railroad-type steam shovels of from ½ to 1-yd. capacity. Picks and shovels, with negro labor loading the phosphate ore (called "matrix") into wooden side-dump skip-cars, was continued until about 1907. From the discovery of hard-rock phosphate until approximately 1905, overburden was removed with mules and scrapers. At some places, the overburden was loaded into side-dump skip-cars by negro laborers and the cars were then pulled up an incline with a steam hoisting engine. The maximum depth of overburden that could be economically removed by hand labor, mules and scrapers was approximately 15 feet. About 1905 one of the companies erected a producer-gas powerhouse near Dunnellon and generated its own electricity and about the same time the larger companies began using hydraulic methods for the removal of overburden. From the year 1888 through the year 1939, approximately 75 companies were operating at one time or another in the hard-rock territory, on approximately 500 locations. The hard-rock deposits are more irregular and have higher mining costs than the pebble-rock deposits, therefore they have not been competitive in the domestic market, but because of the higher grade of the hard rock it is in demand for the export trade. Discovery of phosphate outside of the United States has made it increasingly difficult in recent years for the hard-rock companies to survive, so today only three companies are operating. These

Jan 1, 1941

By Joel J. Lloyd

The storage and retrieval of geological information is represented by a "Babel" of systems. If the energy and expense that is being expended is to be fully exploited by the earth science community, a common language and common practise is required. Interfacing, applicable in the crossover of scientific disciplines and of polyglot data collections, is neither practical nor economic in the handling of English language information. Whether a single input/output center or a locus of interlocking subcenters is established, is irrelevant. The capture of fugitive information and recapture of lost data is paramount. Existing national committees and international commissions are cognizant of the problem and are engaged with it. The time required to reach agreement may merely complicate the problem. It may prove necessary for a group of individuals to face up to the situation and take the indicated action -- facing the criticism that will probably fall on their heads. The cost of rectifying immediate mistakes may be far less than the delayed execution of a long studied plan. System designs are considered in terms of input elements and output products, various mechanical operating modes are presented, and the economics of organization and maintenance are discussed.

Jan 1, 1969

By P. Somasundaran, H. S. Hanna

The separation of minerals such as apatite and scheelite by flotation from other salt-type minerals such as calcite is extremely complex owing to the close similarity between their physicochemical properties. In this paper, properties relevant to flotation such as crystal structure, solubility, surface charge and adsorption behavior of important salt-type minerals are examined along with the role of inorganic modifying agents such as silicates and polyphosphates and organic modifying agents such as starch and tannin. Flotation characteristics of these minerals are then reviewed and selected separation problems involving salt-type minerals are discussed.

Jan 1, 1976

By M. E. Lombardi

THE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 8 ¼ in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling.

Jan 2, 1915

By B. E. Morgan, C. K. Dumbauld

The need for a low-strength cementing composition for use in well cementing is reviewed and results are presented of laboratory and experimental field tests of a modified cement having a controlled ultimate tensile strength of approximately 200 psi. The modified cementing composition may he prepared from either high early strength or normal portland cements by the addition of bentonite clay and a suitable agent for dispersing and controlling the set of the slurry. Substitution of the modified cement for conventional slow-set cements may give better completion results in many wells because the modified cementing composition has lower set strength, lower slurry density, and greater slurry stability than conventional cement slurrieh. The lower ultimate strength allows greater penetration with less shattering of the set cement when perforating casing and cement. The lower elurry density allows the placement of longer columns of cement slurry, and the greater slurry stability reduces the possibility of having an uncemented section caused by the settling of cement particles before the cement set.. INTRODUCTION High strength lias always been one of the accepted criteria of a good cement. During the early use of portland cement in well cementing. emphasis was placed upon securing cements with higher strengths. In 1931, Barkis' reported that, "Normal oil well cements have been improved to develop greater strengths and uniformity of product, which has aided in producing successful jobs in cementing the deeper strings." As long as most wells were completed by the open-hole method. the use of cements having high strengths seemed desirable, and there was no objection raised against high-strength cementing compositions. For a number of years. how-ever, the industry has been completing a large numher of wells by setting and cementing casing through productive horizons and then obtaining production by gun-perforating the section of casing opposite the desired interval. Although this method has been generally successful, difficulties have been experienced in some cases in completing or recompleting wells because of apparent lack of adequate penetration by the bullets through the casing and surrounding sheath of cement and into producing formation. In addition to the penetration trouble: there have been indications that fracturing and shattering of the set cement by perforating might he a contributing factor in causing the failure of some jobs to exclude water or gas from oil producing zones. The possibility that cements having high set strengths were contributing to til difficully ill obtaining satihfartory perforating results has re. ceived attention during recent years. Gun perforating tests conducted in 1944 showed that the depth of bullet penetration into set cement varied with the hardness of the cement, the greater the strength of the cement the less being the penetration. In 1946, Farris2 pointed out that high strength cements were not needed in well cementing, and in 1947, data published by Oliphant and Farris3 showed that set cement was perforated without shattering at approximately 150 psi tensile strength. whereas at approximately 300 psi tensile strength severe cracking and shattering occurred. Oliphant and Farris suggested that wells be perforated at the proper time interval after placement of the cement so that the set cement would have the desired strength. Several difficulties may he encountered in trying to perforate a cement job at the correct time to catch the tensile strength near 150 psi. The rate of strength development of different cements varies considerably. This fact is illustrated by results of tensile strength measurements presented in Fig. 1. These data show that at 175°F the tensile strengths of three conventional slow-set cements varied from 75 to 235 psi at the end of 12 hours. After 24 hours, the tensile strengths varied from 200 to 455 psi. The rate of strength development is affected. also. by the temperature of the forniation, and this adds to the uncertainty of perforating at the rorrect time, since accurate well cementing temperatures may not he known in many cases. Furthermore, in the recomple-tion of wells it is sometimes necessary to perforate cement which has set for a long period and has developed maximum or final strength. In view of the apparent need for a cementing composition having a controlled ultimate strength, an investigation was

Jan 1, 1951