Search Documents

By Leland Russell van Wert

In 1888, Howard,1' working at the Watertown Arsenal on the tensile properties of ferrous materials at various temperatures, noted the curious fact that the stress-strain diagrams of low-carbon steels tested within a certain temperature range (200" to 350" C.) departed more or less from the normal regularity of such diagrams as secured by testing at either above or below these temperatures. This same jagged appearance of similar diagrams for steels has been observed by at least one other investigator, and de Forest2 has reported similar irregularities in the tensile testing of some nonferrous alloys. Recently again, this anomaly in diagram contour has been shown in a most striking fashion, apparently because of its accentuation by the method of testing employed, by Dr. Albert Sauveur.~ He described (for nonaustenitie steels) two quite distinct types of torsional stress-time diagrams: (1) those with a regular and smooth outline, derived normally by testing at temperatures above 300" C., or below 200" C. (as, for example, Figs. 4a or e); and (2) those presenting a decided "stepped" appearance, which are invariably produced when twisting is done within the 200" to 300" C. range (examples, Figs. 5a and b). The torsion test brings out so much more sharply (and convincingly) the irregularities occurring at 200' and 300" C. than does the tensile test that they can no longer be considered as resulting from simply idiosyncratic or accidental and inconsequential causes. Clearly, from the temperatures involved, the "stepped" type of diagram, or more accurately, the peculiar manner of response to torsional stress which manifests itself in the diagram, is an aspect of the "blue-heat" phenomenon. One's curiosity, if nothing else, prompts an inquiry as to the nature and significance of these "steps." What do they mean? What causes them To these questions there are no completely satisfactory answers. The following experimental observations are offered as suggestions towards the solution of the problem.

Jan 1, 1931

By J. C. Karcher

GEOPHYSICAL methods have been more extensively applied to prospecting for oil during 1936 than at any previous time. Their use has been extended to include al- most every oil and gas producing area in the United States. More than ten magnetometer parties, more than nine gravimeter parties, more than five electrical surveying crews, more than fifty torsion balance parties, more than two hundred seismic reflection parties, and several refraction parties were- operating in the United States throughout the year. A tendency has been noted to abandon the use of the pendulum for geophysical prospecting in the oil fields and to increase the use of the

Jan 1, 1937

By Claus G. Goetzel

Pressing of powdered metal parts is best done in the direction of the shortest extension of the piece, to avoid too great a loss of pressing force through internal iriction. As long as curved surfaces, re-cessej, or offsets occur only parallel to this shortest axis of pressure, no special difficulties arise: the cross sections, perpendicular to the pressure, do not vary, nor does the shape of the parts change during compression except for a gradually reduced thickness (Fig. IA). The problem becomes more dificult, however, when the curved surfaces or recesses are perpendicular to the shortest axis of the part (Fig. IB) Two processes for molding uniformly dense parts with complicated shapes from powdered metals are described in detail in this paper. Both can be employed successfully by those trained in the art. The first refers to curved parts; the second is especially adapted to parts having one or more recesses or steps. Both methods, as set forth here, are applied under the condition that presents the more difficult problem. For clarity, before description of the two practical methods, the variable factors in molding powdered metal parts will be reviewed, then an idealized procedure will be considered briefly. Variable Factors in Molding Powdered Metal Parts Compression Ratio Compression ratio is defined as the proportion of the final relative density of the compact to the apparent density of the powder. For iron powder of an apparent density of 3.0, for example, a compression ratio of 2 1/2:1 would be required to produce a compressed compact of 7.5 density; whereas for another iron powder having an apparent density of only 1.5, a compression ratio of 5:1 would be required to produce the same density. The lower the powder's apparent density, the greater must be the compression ratio for pressing compacts of high density.

Jan 1, 1946

By Claus G. Goetzel

Pressing of powdered metal parts is best done in the direction of the shortest extension of the piece, to avoid too great a loss of pressing force through internal iriction. As long as curved surfaces, re-cessej, or offsets occur only parallel to this shortest axis of pressure, no special difficulties arise: the cross sections, perpendicular to the pressure, do not vary, nor does the shape of the parts change during compression except for a gradually reduced thickness (Fig. IA). The problem becomes more dificult, however, when the curved surfaces or recesses are perpendicular to the shortest axis of the part (Fig. IB) Two processes for molding uniformly dense parts with complicated shapes from powdered metals are described in detail in this paper. Both can be employed successfully by those trained in the art. The first refers to curved parts; the second is especially adapted to parts having one or more recesses or steps. Both methods, as set forth here, are applied under the condition that presents the more difficult problem. For clarity, before description of the two practical methods, the variable factors in molding powdered metal parts will be reviewed, then an idealized procedure will be considered briefly. Variable Factors in Molding Powdered Metal Parts Compression Ratio Compression ratio is defined as the proportion of the final relative density of the compact to the apparent density of the powder. For iron powder of an apparent density of 3.0, for example, a compression ratio of 2 1/2:1 would be required to produce a compressed compact of 7.5 density; whereas for another iron powder having an apparent density of only 1.5, a compression ratio of 5:1 would be required to produce the same density. The lower the powder's apparent density, the greater must be the compression ratio for pressing compacts of high density.

Jan 1, 1946

By Lyman H. Hart

Some of the significant facts that will affect the supply and demand for metals during the next few decades are given in this presentation. This is important because the only hope for intelligent guidance of the national destiny depends upon presenting a consistent and accurate picture of basic problems. The metals problems now fomenting are only slightly less important than those precipitating the energy crisis. Admittedly, it is difficult to generate serious thinking on this subject when the world is enjoying easy access to all metals at modest prices. This is possible because of the current world capacity to overproduce, and United States credit standing, at least up to now, has permitted buying freely on world markets. Although both these vital conditions are subject to change, there is little doubt that if the U.S. financial house is kept in order, we can muddle along for a while on a generally expanding, metalbased economy. But should our credit standing be permitted to collapse, or should there be a tightening of world supplies of metals, the nation would immediately find itself in trouble. Unfortunately, clear signals indicate that both of these conditions are threatening.

Jan 4, 1973

By R. B. Schluter, M. M. Fine

The Bureau of Mines' Twin Cities Metallurgy Research Center has of late concerned itself with reduction-induration of iron ore. One development provided a flowsheet for the agglomeration of green concentrate pellets in a reducing atmosphere created by a solid reductant external to the agglomerate. The product pellets were well metallized and physically competent. Maximum recommended operating temperature was 2100º F. In these studies, it was observed that unflred iron ore pellets indurated in a bed of anthracite or certain lignite chars frequently acquired exceptional crushing strength. A diagnosis of the phenomenon revealed that sulfur in the fuel was the probable cause. Accordingly, a research program was established to test this premise and to put it to practical use. Gaseous reductants were employed initially because of the ease and accuracy with which they could be metered.

Jan 10, 1969

By Z. Moser, W. Ptak

The experiments were carried out by the method of measuring the electromotive force of concentration cells having zinc as a reference electrode, the second electrode being the liquid alloy Zn-Sn-Cd-Pb. The electrolyte consisted of liquid chlorides and had zinc ions. The measurements were made for seventy -five alloys of different mole fractions within the temperature range of 714° to 877°K. The experimental results enabled the calculation of the activity of zinc in tested solutions. The activities of zinc were calculated by means of Krupkowski's formulas.3 In addition, the formulas for coefficients of activity of zinc, tin, cadmium. and lead as the function of composition and temperature were given. Activity of zinc was compared with the values obtained from experimental results, and good agreement has been observed. On this basis it can be stated that the theoretical formulas are suitable for determining the thermodynamic properties of liquid quaternary metal solutions. IN the metallurgical processes being carried out at present multicomponent liquid metal solutions take part. For the thermodynamic analysis of these processes it is necessary to know the thermodynamic properties of these solutions. Therefore, many experimental and theoretical papers deal with this problem. The theoretical papers are generally based on the assumption that the structure of liquid metals is similar to their structure in the solid state. In this manner the model of liquid solution, consequently described by means of statistical thermodynamics, has been accepted. This method is being lately developed, especially for solid solutions. Statistical thermodynamics was applied among others by Guggenheim 1 for describing the thermodynamic properties. Unfortunately, the formulas of statistical thermodynamics are often not suitable for the interpretation of experimental results. Attention should be drawn to the relations obtained by means of formulas of phenomenological thermodynamics which always have constants derived with the aid of experimental methods. In the case of the multi-component solutions which contain some additions of impurities besides the basic metal, wagner2 introduced interaction parameters. Equations for the relationship between the activity coefficients and composition were also given by Krupkowski." he application of these formulas requires a good knowledge of the thermodynamic properties of the corresponding binary systems. In these formulas, as in Wagner's, there appear constants which should be determined from ex- perimental data. Nowadays, different experimental methods are applied for evaluating the thermodynamic functions of solutions, for instance: vapor pressure measurements, calorimetric methods, and the measurements of electromotive force of concentration cells. In the present paper this last method for evaluating the thermodynamic properties of four-component systems, Zn-Sn-Cd-Pb, was applied. For instance in the case of Zn-Sn solutions Alabyshev and Landratov, 4 Fiorani and Valenti, 5 and ptak6 performed the investigations. The Zn-Pb system was worked out by Kleppa 7 and Cd-Pb and Cd-Sn by Elliot and chipman.' This method was also applied for determining the activity of zinc in ternary solutions. 1) EXPERIMENTAL METHOD The experimental arrangement with detailed description is given in Fig. 1. It consists of resistance furnaces, one serving for melting samples and the other containing the flat-bottomed, measuring quartz tube with the liquid electrolyte. Liquid metals and alloys are in glass supremax tubes, which have an opening in their lower part above the metal level. This opening allows the filling of the tubes by the electrolyte. In these tubes tungsten wires are placed which by means of suitable conductors are connected with a potentiometer. It is assumed that tungsten dissolves Fig. 1—Schematic diagram of the experimental arrangement for the investigation of the thermodynamic properties of liquid metal solutions: 1, resistance furnaces; 2, autotransfor-mers; 3, galvanometers; 4, regulator of temperature; 5, gas purifier with concentrated H2SOP; 6, U-tube with P2O5; 7, thermostats; 8, steel block for thermostating; 9, supremax tubes for alloys; 10, tungsten electrodes; 11, inlet and outlet of argon; 12, measuring quartz tube; 13, tube for melting samples; 14, tube for thermocouple; 15, cover of quartz tube; 16, rubber seal; 17, bottom cover; 18, outlet of electrodes to potentiometer; 19, outlet of thermocouples to potentiometer; 20, upper view of the quartz tube cover; 21, orifices for cover screws; 22, orifice for argon inlet; 23, orifice for thermocouple; 24, orifices for tubes containing liquid metals; 25, inlet for water-cooling system.

Jan 1, 1969

By Wilbur I. Duvall, Thomas C. Atchison

Over the past ten years a series of investigations have been conducted to determine some of the physical processes involved in breaking rock with confined concentrated charges. Detailed discussions of many of these investigations have been published elsewhere.1-6 Laboratory experiments made by other investigators using Hopkinson pressure-bar techniques have shown that solid materials are fractured in tension by the reflection of an incident compressive stress pulse at a free surface.7-12 In these tests a small charge of explosive is placed in contact with one end of a bar. Detonation produces some plastic flow and crushing of the bar near the charge and generates a compressive stress pulse that travels along the length of the bar. At the free end of the bar the compressive stress pulse is reflected back into the bar as a tensile stress pulse. If the tensile strength of the bar is exceeded during this reflection process, a tensile fracture normal to the length of the bar is produced, and the broken end of the bar moves forward with a constant velocity equal to the average particle velocity trapped in the broken fragment. The new surface formed by the fracture becomes the new free end of the bar that reflects the remaining portion of the incident compressive stress pulse. This process is repeated any number of times until all of the incident stress pulse is reflected.

Jan 6, 1959

By C. R. Dodson, D. Goodwill, E. H. Mayer

The paper summarizes the historical background of the pressure-volume-temperature analyses of reservoir fluids, the errors involved in both the sampling and testing of reservoir fluids, the type of information required of a PVT determination, and the field conditions that limit the application of any one analysis. Particular emphasis is placed on the necessity for approximating as closely as possible the liberation sequence occurring in the producing formation, flow string, and surface separators. A combined differential and flash or "composite" liberation is suggested as the best means of approximating this liberation sequence. HISTORICAL BACKGROUND Petroleum reservoir engineering commonly is considered to be one of the newest fields of petroleum science, yet much work of a theoretical and intuitive nature was done many years before the modern techniques of reservoir analyses were developed. The period 1910-1924 saw considerable work in the field of reservoir behavior done by the U. S. Bureau of Mines. This work:.' although entirely theoretical, pointed out the importance of gas in the recovery of oil from the reservoir. The statement by J. 0. Lewis that 20 per cent or less of the oil originally in place in a pool was recovered from the ground under uncurtailed production conditions caused some operators to re-examine and modify their production methods. However, though these works showed methods of production that have subsequently resulted in greater oil recoveries, they in general went unnoticed, even though there was a fear that the nation's petroleum resources were being exhausted. The period 1924-1933 saw the industry take considerably more interest in reservoir behavior because of an unfounded fear of its inability to replace oil reserves, the possibility of government regulation, and the energy of one man, Henry L. Doherty. Doherty aroused heated discussions in the industry concerning conservation. To prove or disprove his theories the first experimental work on the reservoir behavior of petroleum was undertaken. The papers of Dow and Calkin,' Beecher and Parkhurst," and Mills and Heitheckere are classics although their experimental procedures were crude. These papers proved that the properties of petroleum in the reservoir are quite dissimilar to the properties measured at the well head. Gas dissolved in the oil phase was recognized as having considerable importance as had been predicted by the earlier theorists. Slightly later Miller and his co-workers assembled the first text correlating all the known data on the reservoir behavior of petroleum and used, these data to show the economic value of conservation. Quantitative application of pressure-volume-temperature analyses of reservoir fluids was given in the paper of Coleman, Wilde, and Moore"; this work showed that with sufficient laboratory and production data prediction of reservoir behavior was possible. The refined sampling and labora-

Jan 1, 1953

By Noel H. Stearn

OF the many instruments devised for the measurement of magnetic anomalies, the ordinary dip needle, by virtue of its superior simplicity of construction, facility of manipulation, and definiteness of interpretation, seems to merit serious attention as the instrument most readily applicable to the detection of magnetic anomalies of the higher order of magnitude. In spite of the fact that it has been used for many years for the discovery of iron ore in Europe and in the Lake Superior region of America, its capabilities as a geological instrument have not yet been thoroughly plumbed. The Wisconsin Geological Survey, under Dr. W. 0. Hotchkiss, E. F. Bean, and H. R. Aldrich, has been most thorough in developing the technique of the instrument, and the results it has obtained have aroused a general interest in a more widespread use of geomagnetics as an exploration method and the dip needle as a geological instrument. The simplicity of the instrument is an especial advantage, as it can be used by anyone, regardless of his technical training; but to insure useful results not only is a knowledge of the background of geomagnetics necessary but also an understanding of the principles of the instrument itself. Principles of the Dip Needle The major feature of the dip needle is an elongated magnet suspended with fixed bearings in such a way that it can move in a single plane. If the point of suspension were exactly at the center of gravity of the magnet, the instrument would be identical with the "dip circle" or "dipping needle" of terrestrial magneticists, and as such could be used to determine variations in the inclination of the earth's magnetic field when observed in the plane of the magnetic meridian. The dip needle, however, differs from the "dip circle" or "dipping needle" in having an adjustable counterweight affixed to one end of the magnet. This counterweight serves to balance the magnet at an angle to the inclination of the earth's field when the instrument is oriented in the plane of magnetic

Jan 1, 1929

By AIME AIME

THE Petroleum Division will hold its first fall meeting in Tulsa, Okla., Thursday and Friday,' Oct. 2 and 3, preceding the. International Petroleum Exposition that opens there on Oct. 4. Headquarters will be at the Hotel Mayo, and members planning to attend should make reservations promptly because of the large attendance expected at the Exposition. The program for Thursday will feature production engineering problems and that for Friday the unit operation of oil pools. The principal papers planned for the various sessions are as follows:

Jan 1, 1930

By R. L. Perrine

This paper shows how stability theory can be used to optimize solvent recovery of oil. Application of the theory leads to definition of the limiting conditions required for stable displacement to occur. One of these conditions is that the size of a solvent "slug" must at least equal a prescribed minimum. The criteria to be satisfied are miscibil-ity and stability. Stability implies that no viscous fingering will occur and that mixing will be caused only by a dispersion process. Miscibility implies that complete recovery will be obtained from the swept regions. Thus, for any specified set of reservoir conditions, an optimum use of solvent is defined. INTRODUCTION The early outlook for solvent flooding as a means to increase oil recovery was very favorable. Some laboratory results indicated that a "slug" containing perhaps 2 to 3 per cent of a hydrocarbon pore volume could be successful. However, other data suggested as much as 30 per cent would be required. The difference is of considerable economic importance. A theoretical explanation for these divergent results has been advanced by the author.1,2 Stability theory defines conditions for two distinct flow regimes. In stable displacement, solvent and oil become mixed by a dispersion process, and the solvent requirement is small. On the other hand, unstable displacement can degenerate into viscous fingering. The practical result is a considerable increase in the extent of mixing and, thus, in the solvent required. The present paper shows how to use stability theory to optimize solvent recovery of oil. Oil is usually considered to be displaced by a small amount, or a slug, of solvent. Gas in turn follows solvent. Any fingering will permit contact of nearly solvent-free gas and oil, leading to immiscibility and reduced recovery. Thus, our optimum is defined by two restrictions — stable flow and miscibility. Although an immiscible solvent process could prove more profitable than any miscible process, such processes lie outside the selected definition of an optimum. The usefulness of computations based on the present work will depend on the validity of the general theory. Because the important idealizations required tend to minimize the predicted solvent requirement, the results should state correctly the limiting conditions required. Therefore, theoretical calculations should have practical value. This paper first reviews several principles that result from stability theory. The following section describes use of these ideas in relatively simple systems which symmetry makes appear one-dimensional. Of particular importance is the step-by-step design of 3 stable minimum-solvent slug. The use of stability theory in cases of multi-dimensional displacement is discussed and, finally, suggestions are given for simplified practical application of the theoretical results. PRINCIPLES OF STABILITY THEORY The use of perturbation methods to derive stability conditions has been shown by the author.l The discussion is presented in terms of the fractional concentration of solvent in the single hydrocarbon phase. Quite generally, any disturbance can be represented as a Fourier series, of which only the least stable term need be considered. Denoting this term at time t = 0 by cn,

By C. M. Boss

Throughout the Lake Superior Basin each of the great ironranges, from which vast quantities of iron-ore have been, and are now being mined, presents characteristics differing from each and all of the others. One of the most peculiar of these varying features is found in the dikes of the Gogebic range. From an economical standpoint this feature of the dikes has been studied by our practical mining men more than any other geological phenomena in connection with the deposits of merchantable iron-ore. In the greater portion of our mines these dikes appear to form the riffles in the sluice of the ore formation, against which the particles of iron oxide are deposited in the process of concentration out of the quartzose matrix which is termed the ironbearing formation. In composition these dikes are apparently of a dioritic formation, more or less altered and decomposed, comparatively soft, and sometimes almost steatitic. While frequently showing something of a cleavage in the direction of their pitch, they are devoid of parallel laminæ, and when broken assume the form of irregular angular fragments. They are generally of nil ashy grey color, but sometimes at great depth are found to be quite dark, almost black, and of a very hard massive nature, showing radial or fibrous crystallization. Practically all of the dikes thus far discovered in the iron formation are approximately at right-angles with the dip of the formation, and the greater number of them have an average easterly dip of from fifteen to eighteen degrees. Sometimes, however, they are folded in such a manner as to form long synclinal basins; but while their western or initial extremity is fre-

Jan 1, 1898

By W. E. Forsythe

Different forms of optical pyrometers are discussed and the advantages and disadvantages of the different types for measuring high temperatures are pointed out. These advantages and disadvantages lead to the selection of the disappearing-filament type of optical pyrometer for most work. Attention is directed to the necessity for the use of a monochromatic screen with a pyrometer, which leads to a discussion of the meaning and use of the effective wave length of the screen. Methods of calibrating the optical pyrometer are outlined and it is shown that an optical pyrometer can be calibrated just as definitely as any other temperature-measuring device. Accuracy tests are included, in which it is shown that excellent results can be obtained by even untrained or slightly trained observers with this form of optical pyrometer. The various corrections that are necessary in this kind of work are indicated, including corrections for stray light, for absorption of windows, of smoke, and so forth. The troublesome problem of measuring the temperature of bodies that do not radiate like a black body is discussed and the corrections for reducing such readings to the true temperature are given for a number of different materials. Introduction The fundamental idea of temperature depends upon our temperature sense and bodies are said to be hot or cold depending upon the reaction of our hands or some other part of the body to the heat from the source investigated. For measuring the temperature some instrument must be devised, since the temperature of the source studied is apt to be so hot as to greatly injure any part of the body that comes near it, to say nothing about direct contact with it. Definition of Temperature.—The temperature scale is based upon two fixed points, the temperature of freezing water and the temperature of boiling water. This temperature interval, depending upon the scale

Jan 1, 1936

By W. E. Forsythe

Different forms of optical pyrometers are discussed and the advantages and disadvantages of the different types for measuring high temperatures are pointed out. These advantages and disadvantages lead to the selection of the disappearing-filament type of optical pyrometer for most work. Attention is directed to the necessity for the use of a monochromatic screen with a pyrometer, which leads to a discussion of the meaning and use of the effective wave length of the screen. Methods of calibrating the optical pyrometer are outlined and it is shown that an optical pyrometer can be calibrated just as definitely as any other temperature-measuring device. Accuracy tests are included, in which it is shown that excellent results can be obtained by even untrained or slightly trained observers with this form of optical pyrometer. The various corrections that are necessary in this kind of work are indicated, including corrections for stray light, for absorption of windows, of smoke, and so forth. The troublesome problem of measuring the temperature of bodies that do not radiate like a black body is discussed and the corrections for reducing such readings to the true temperature are given for a number of different materials. Introduction The fundamental idea of temperature depends upon our temperature sense and bodies are said to be hot or cold depending upon the reaction of our hands or some other part of the body to the heat from the source investigated. For measuring the temperature some instrument must be devised, since the temperature of the source studied is apt to be so hot as to greatly injure any part of the body that comes near it, to say nothing about direct contact with it. Definition of Temperature.—The temperature scale is based upon two fixed points, the temperature of freezing water and the temperature of boiling water. This temperature interval, depending upon the scale

Jan 1, 1936

By N. J. Grant, D. S. Bloom

THE development of high temperature, high stress alloys had proceeded with such rapidity during the war, and for a short time afterward, that our knowledge of the constitution of the alloys had become seriously inadequate. To interpret correctly alloy behavior it is not only necessary to recognize the phases present, but also to know the properties of the phases under all varieties of conditions and treatments. Chromium in these high temperature alloys holds the unique distinction of being the only one element which must be present when an oxidizing or generally corrosive atmosphere is present and when a long life is desired in service. Carbon and nitrogen must also be considered where chromium is present. Carbon is always present, either as an impurity in the raw alloying elements, or as a deliberate addition agent to increase the strength. Nitrogen is generally picked up from the atmosphere during melting or may be added as an alloying element. The effect of nitrogen additions is not too dissimilar to that of carbon additions. As such, chromium carbides and nitrides become of great interest since they are present in a very large number of alloys, including alloy steels, stainless steels, super alloys, and the like. In the chromium-carbon system there are three accepted, carbides: Cr,C, Cr7C8, and Cr3C2. The existence of one more carbide, a still higher carbon form CrC, has been advanced. The phase diagrams of chromium and carbon as published by Friemann and Sauerwald² and by Tofaute, Kuttner and But- tinghaus³ -do not extend beyond the carbide Cr3C2, which contains 13.3 pct carbon; but Hatsuta has extended the diagram up to 20 pct carbon, and in doing so hypothesized, with the use of some questionable experimental results, the compound CrC. This carbide would contain 18.75 pct carbon, 81.25 pct chromium, by weight. It is further known that as the chromium carbides increase in carbon the acid resistance increases but the oxidation resistance decreases4,5 This is of great importance in high temperature alloys where time-temperature stability, as well as oxidation resistance, is of prime importance. The possible existence of a carbide of the formula CrC thus becomes of prime importance and it was considered important to recheck the chromium-carbon binary constitutional diagram for such a compound. In view of the wide spread of values listed for the melting point of chromium (1500° to 1850°C) and 1930°C8, it was considered .that the liquidus temperatures might well be redetermined more ac-

Jan 1, 1951

By Charles W. Goodale

The purpose of this paper is to review the history of the Drumlummon, one of the famous old mines of the West. Mining engineers, when sent to examine new mines in old districts, or, to decide whether an old property, under new conditions, will pay to reopen, have had difficulty in learning anything authentic regarding workings which are under water, and historical facts about the working character of the ore, the total production, and the value of the ore with increasing depth. 'Not many years elapse after the pumps are pulled, before maps, books and records are destroyed, and the value of the publications of the Institute would be increased if they contained the history of many old mines now abandoned. The unsuccessful efforts of the writer quite recently in trying to obtain reliable information about a gold mine which was reported to have produced several million dollars between 1880 and 1888, the workings of which are now partially caved and under water, impressed upon his mind the desirability of having a permanent record of old properties. In this particular case, the owners insisted that under present conditions of improved methods of treatment —particularly by the use of cyanide, which was not an applied process when the mine was operated, the property could be made to pay a handsome profit on ore left in sight in the old workings, but no assay records could be found to confirm these assurances, and even the records of bullion shipments had been destroyed. If surveys and maps were made as the work progressed, no trace of them could be found, and therefore opening of the ground through a new shaft and drifts therefrom would be attended by some risk while exploring near the old workings. Fatal accidents by flooding under these conditions have occurred, and as an evidence that miners have fears of such dangers, it was urged upon the Mining Committee during a recent session of the Montana Legislature, by a delegation of

Jan 1, 1915

By R. H. McLean

Velocity, kinetic energy and shear in crossflow beneath three-cone jet bits may influence cleaning of the bottom of the borehole and the teeth of the bit. Laboratory investigation shows that each of these parameters is a function of the diameter of the borehole and the product of the volume rate of flow and velocity through the nozzles (QVn). Increasing QV, or decreasing the diameter of the borehole increases each parameter. These functions provide means of predicting the magnitude of each parameter and of scaling the cleaning forces. INTRODUCTION In drilling operations using conventional jet-type rock bits, the impinging jels create an important flow mechanism. Called crossflow, this flow mechanism originates in the impact area of the jets, spreads across the bottom of the hole and supplies the principal source of energy to clean the teeth of the bit and most of the bottom.' Besides providing the means of cleaning cuttings from the bit and the hole bottom, crossflow may also have other, less direct, effects on the rate of penetration. The shear stress generated on the bottom by crossflow will inIluence the thickness and permeability of any filter cake of mud solids or crushed material which forms on the bottom.' These factors may affect the rate of penetration. A previous pulblication introduced some fundamental concepts of crossflow.' Crossllow was shown to occur in a thin layer adjacent to the bottom, and to cover the bottom completely. The maximum velocity in the crossflow above any position on the bottom was found to be directly proporlional to the square root of the product of the volume rate of flow and velocity through the nozzles—the jct QV,,—and inversely proportional to the diameter of the borehole. This information indicated that the effectiveness of crossllow in scavenging the bottom can be improved by maximizing the jet QV. The investigation reported herein amplifies the definition of crossflow. Complete velocity profile data above a representative position on the bottom are analyzed. These data better illustrate control of the capacity of crossflow to scavenge the bottom, and also relate shear stress on the bottom to known, controllable parameters. The conclusion reached in the previous publication that maximization of the jet QV. produces the maximunl cleaning beneath current jet bits is unchanged by these new data; rather, it is strcngthened. Data presented here show that the kinetic energy flux above a representative position on the bottom is maximized by maximizing the jet QV. The shear stress on the bottom will also be shown to be maximized in the same manner. Since the functions relating the jet QV. to velocity, shear stress and kinetic energy also involve the diameter of the borehole, means of equating, or scaling, these quantities in different sizes of boreholes will be illustrated. EXPERIMENTAL EQUIPMENT AND TECHNIQUE JET BIT MODEL Data were recorded from the same laboratory model as used in the aforementioned investigation of the flow around a jet bit.' The model consisted of a 43/4-in. three-cone, jet-type rock bit in a smooth, flat-bottomed borehole constructed of lucite. The bit had a shape and nozzle placement closely resembling larger three-cone jet bits commonly used in field operations. Fig. 1 illustrates the impact area on the bottom of a jet from this bit. Details of the orientation of the jets may be found in the previous publication. TECHNIOU'E OF MEASUREMENT Measurements of the crossflow were made by inserting a very small Pitot tube through the bottom of the simulatetl boreholc. Extreme thinness of the layer of crossflow necessitated accurate measurements of the height of the Pitot tube above the bottom to achieve close definition of the velocity profile. A cathetometer, which could be read to the nearest 0.005 cm, was used to make this measurement.

Jan 1, 1966

By J. A. B. Forster

The operations of the Electrolytic Zinc Co. of Australasia Ltd. involve the preliminary roasting of zinc concentrate from Broken Hill, New South wales, at a number of acid-making centers on the Australian mainland. The partially roasted material is shipped to the Tasmanian plant where it was formerly re-roasted prior to leaching,' but this practice was gradually abandoned in favor of the flotation of leach residue for the recovery of a concentrate containing about 22 pct sulphide sulphur and known as secontlary or Risdon concentrate.2 This change, together with increased zinc production, called for new furnaces at Risdon for the roasting of 10-50 tonst of secondary concentrcite and 90 tons of new concentrate per day. The war situation made it imperative that construction be commenced without delay and to save time it was decided to base the design on that of Skinner type furnaces which had been built in South Australia twenty years earlier. This involved some sacrifice of desirable features but did not prevent the incorporation of provisions which had enabled small Herreshoff type furnaces to roast secondary concentrate autogenously. The roasting rate in existing furnaces was 10-12 Ib sulphide sulphur per sq ft of hearth area per day, and eleven hearths, 20 ft in diam, were provided in the two new furnaces in anticipation that they would prove capable of the autogenous roasting of 130-140 tons of concentrate per day from 28-29 pct sulphur down to 4.5-5 pct, with an oxidation rate of 11-11.5 lh S/S per sq ft of hearth area per day. It was soon realized, when the first of the furnaces went into operation, that a much better performance than this might be given, and the purpose of this paper is to show how a treatment rate of 100 tons per furnace day, and oxidation rates approaching 15 lb S/S per sq ft per day have been reached. Furnace Design General specifications for the design were based on the results of experience with several other types of furnace and on the special operating conditions

Jan 1, 1950

By R. Moldenke

Unlike the furnaces employed in the reduction of ores to mattes and metals, the foundry-cupola has only melting to do. This looks simple enough; and its development has progressed through centuries by cut-and-try methods; but there is still much to be learned concerning the causes which underlie the production of defective castings, even from first-rate materials. There are other differences between the smelter and the cupola. The former is usually, the latter rarely, run continuously. In the smelter there is some chance for experiment, since rich slags can be treated again; while in the cupola the metal must be good for casting from the first tap to the drop of the bottom ; otherwise, heavy damage will result. In the smelter, the object sought is the production of metal or matte with a minimum loss in the slag; whereas, in the foundry, a variety of castings of different compositions must often be run from the same heat, one after the other. Experience with the cupola has shown that the melting should take place, throughout the heat, in one zone, the zone of maximum temperature, which is clearly marked on the cupola-lining by the severe cutting action of the slag and iron oxide. The design and operation of the cupola must conform to this condition. This conformity having been secured, other considerations resolve themselves into those details of construction which will involve least trouble and cost of repairs. The very high temperatures required to melt iron and steel in the cupola, leaving the metal sufficiently superheated for casting, render the use of water-jackets inadvisable. It is always possible to patch up the lining at the melting-zone between daily heats; and the rest of the lining is seldom affected enough by abrasion and chemical action to require replacement oftener than once in nine months. The cupola is practically a shell of steel, lined with the proper refractory material, and provided with a sct of tuyeres for the admission of air to burn the fuel and melt the metallic

Jan 1, 1913