Search Documents

By R. I. Jaffee, E. S. Bartlett, D. N. Williams

The oxidation resistance and fabricability of molybdenum powder-metallurgy alloys containing up to 20 wt pct nickel in the form of a fine dispersion were studied. The effects of dispersion distribution and of amount and type (pure nickel or nickel compounds) of additive were considered. A definite improvement in oxidation resistance was observed, but the amount of improvement fell far short of requirements for an oxidation-resistant alloy. Fabricability by hot-rolling was limited. INVESTIGATIONS at Ohio State university1 and Battelle Memorial institute2 have indicated that the attainment of a truly oxidation-resistant molybdenum-base alloy for high-temperature service, with the coincident retention of high-temperature strength and toughness, will be a difficult, if not impossible, feat. Among the most promising alloy systems studied was the molybdenum-nickel system shown in Fig. 1. Alloys in this system show good oxidation resistance at temperatures well above the normal melting point of molybdenum trioxide because of the regenerative formation of protective nickel-molyb-date (NiMoO4) on the surface of the alloy during exposure at high temperatures. Unfortunately, the required alloy content to obtain oxidation resistant molybdenum-nickel alloys far exceeds the limits of the narrow terminal solid-solution boundary, and closely approaches the peri-tectic composition involving the brittle intermetal-lic compound, MoNi. Because of the peritectic reaction, fusion alloys are characteristically brittle, since the MoNi phase, being the last to form, tends to occur as a continuous grain-boundary network around each molybdenum grain. An added problem with this system is that the protective nickel-molybdate layer formed at high temperatures is unstable, undergoing one or more allotropic modifications upon cooling. The volume changes associated with this modification during cooling are such as to cause violent expulsion of the protective molybdate coating from the surface of the piece. This is, of course, quite detrimental in material exposed to cyclic temperature during service. The research reported here resulted from an attempt to overcome the aforementioned problems associated with the molybdenum-nickel alloys primarily by controlling the amount, size, and location of the MoNi phase. By using powder-metallurgy techniques of alloy preparation and sintering the blended molybdenum-nickel powder mixtures at a temperature below the peritectic reaction temperature, molybdenum-nickel alloys with a randomly dispersed MoNi phase were produced. MATERIALS The molybdenum powder used in the preparation of alloys for this study was commercial hydrogen reduced, minus 325-mesh (Tyler) material. Master alloys, by which nickel was added, consisted of elemental carbonyl nickel powder (12 average particle size), an alloy of 50 wt pct Ni-50 wt pct Cr, and compounds of MoNi, Ni,Si, and Ni2B. The nickel-chromium powder was prepared by filing a vacuum-arc-melted ingot, separating impurities magnetically, and screening to minus 200-mesh. The MoNi powder was prepared by pulverizing a hydrogen-sintered powder-metallurgy compact to minus 325-mesh material. Further sizing of this powder for study of effects of dispersion distribution was accomplished by air classification of the minus 325-mesh powder. The Ni2Si and Ni2B powders were prepared by crushing vacuum-sintered powder-metallurgy compacts to minus 200-mesh material. EXPERIMENTAL PROCEDURE Specimen Preparation—The general procedure followed in the preparation of alloys for testing is described as follows: 1) Blending. Either hand-blending of the powders in a ceramic mortar and pestle for X 1/2 or mechanical blending was used. Hand-blending seemed preferable for optimum homogeneity. 2) Compacting. Most of the blended powders were pressed to green compacts at pressures of 15 tons per sq in. in a single-action die, although some were pressed at 80 tons per sq in. A 1 X 11/4 X 1/4-in. green compact was the standard size for oxidation test material, and 7 X 1/2 X 1/4-in. compacts were used for fabricability test specimens. 3) Sintering. All green compacts were sinteredat

Jan 1, 1959

By James C. Bayles

The ideal pressure-tube is obviously the one which combines the greatest strength with the least weight of material consistent with the uses for which it is designed or employed. The inside of the pipe is the first concern of the engineer. It should be cylindrical, smooth, and of the requisite capacity for the purpose in view. It should be in lengths as great as can be oonveniently handled, so that the couplings may be as few as possible. With the walls of the tube the engineer has no further occasion to concern himself than to make sure they are adequate to carry the internal and external pressures to which they will be subjected. It is as true of a pipe as of a truss, that when it is strong enough to give the requisite factor of safety, nothing is gained by having it stronger. Anything more than this means dead weight, which has to be paid for many times, first as material, and again and again in the costs of transportation and handling, until it reaches its place in the trench or on supports. In use it must be and remain tight against all leakage, and must sustain whatever is placed over or upon it, or suspended from it, without deformation or injury. Finally, in addition to meeting all the immediate requirements of service, it must possess qualities of durability which warrant a reasonable expectation of a long life of usefulness. The wise engineer no longer regards it as reasonable to depend upon mere bulk of its own material for the protection of a metal as readily impaired or destroyed by oxidation as iron or steel. The metal must have a coating which will be and remain impervious and indestructible. When all these conditions are met, we have as near an approach to the ideal tube as can be attained with the materials now available for their manufacture. Steel wed constructively, to the best advantage, meets these requirements most perfectly. Gold alone would do it better. If we search through the whole list of metals and alloys we find nothing available which so perfectly meets the requirements as a pipe material as steel. Mr. Hamilton Smith, Jr., in a paper on the expedients adopted on

Jan 1, 1891

By Earl Oliver

The term oil property, in this discussion, includes any type of easement or grant under which petroleum might be produced; it ranges from the mere right to drill on undeveloped wildcat acreage up to a fully developed oil property. The values of an oil property, as thus defined, vary widely according to the use for which it is intended, whether it is from the viewpoint of the speculator, the fraudulent stock promoter, the refiner and pipe-line owner, or the oil producer. The market value of a property is usually a combination of some two or more of these influences, and occasionally a combination of all of them, but we prefer to treat each viewpoint as distinct from the others, allowing the reader to make his own combination in such proportions as his inclination and property seem to require. This paper will treat the subject from the viewpoint of the oil producer. However, the other influences have such bearing on the cost of property to the producer and on the price he might obtain by its sale as to warrant brief discussion of them. Speculation, particularly lease speculation, is a parasitic growth on the oil industry, healthy enough, but of no economic value. The class of property usually dealt in for this purpose is the undeveloped lease. Its speculative value may have some relation to its probable productive value, but most frequently this value is the product of temporary excitement due to local development. The lease speculator, seeking out the trend of development or securing early information regarding a proposed test or a new discovery, immediately secures leases whose market value will be increased when the existence of such development becomes more widely known. His profits are purely unearned increment. Not proposing to spend money in exploration, he can afford to compete in purchase with the operator, who, in addition to bonus paid, must spend large sums in testing out his own acreage and that of the nearby speculator as well. It has a tendency to compel unduly high bonuses. The so-called "checker-board1' system of leasing wildcat acreage by the larger companies is on the same principle of attempting to secure the

Jan 1, 1921

By Max W. Ball

An intelligent discussion of the oil situation and its needs, whether from the standpoint of the prospector, the operator, the engineer, or the public administrative officer, must be founded upon a knowledge of the law under which oil lands are obtained. A consideration of new legislation must be prefaced by an understanding of the present law and its results. This paper undertakes to present no new remedy for the ills of the present situation, no new solution of the problems the oil business is facing. It attempts merely to summarize the present law, its provisions, its origin, its development, and its effects. The discussion does not pretend to be exhaustive from a legal standpoint. It aims to avoid legal intricacies which tend to. confuse rather than clarify. It seeks but to present the essentials of the existing situation. The title to government lands known to contain valuable deposits of petroleum may be acquired only under the terms of the placer law as embodied in Section 2329 et seq. of the Revised Statutes. As a preliminary to considering the desirability of this situation it is profitable to examine into its origin. Origin of the Law Congress has left no room for doubt as to the legal applicability of the placer law to oil lands. The Act of Feb.11, 1897(29 Stat., 526), provides: "that any person authorized to enter lands under the mining laws of the United States may enter and obtain patent to land containing petroleum or other mineral oils, and chiefly valuable therefor, under the provisions of the laws relating to placer mineral claims.' . The immediate cause for the passage of this Act was stated in a brief report in the, House of Representatives (there was no debate in the Senate) to be a decision of the Department rendered Aug. 27, 1896 (Union Oil Co., 23 L. D., 223), directing the cancellation of an oil placer entry on the ground that land containing petroleum cannot be located and entered as a placer mine. The report of the Public Lands Committee of the House contains the following interesting statements Congressional Record, vol. xxix, p. 1409):

Jan 1, 1915

By Arthur Taggart

SOME years ago, A. M. Gaudin and one of the authors published a paper showing removal of tar acids from solution by sulfides preferentially as compared to gangues (specifically by galena as compared to quartz).1 The underlying phenomenon was classed as adsorption, and the paper went on to develop the general thesis that so far as water-soluble frothing and collecting agents in flotation are concerned, the phenomenon of adsorption is one of controlling importance. Adsorption was defined in that paper as "a process of rearrangement of a system, which results in establishing a difference in concentration, as between the interfacial layers and the bulk of the phases, of a substance or substances initially uniformly dispersed in one or several of the phases." The paper went on to develop the relation between adsorption and surface energy according to Gibbs' equation (which may be thrown into the form U/c = KdT/dc, where U = excess concentration in surface layer, c = concentration, T = surface tension, and K is a constant), and pointed out that, according to this equation, degree of adsorption and change in surface tension vary directly. The present paper offers a somewhat different definition for the term adsorption; and sets up, in sweeping terms, the generalization that simple chemical reaction underlies the functioning of the flotation reagents which control mineral collection, when these reagents are soluble in and act from solution in the water of the pulp.

Jan 1, 1930

By J. C. Irvine

The down-the-hole drill is becoming a more common tool in today's underground mining scene. New drilling capabilities and efficiencies are being derived as experience is gained. Ancillary equipment and bits are becoming increasingly important parts of the concept. This paper describes some presently used units; underground down-the-hole drilling units.

Jan 1, 1978

By R. H. Singleton

ThE purpose of this investigation was to determine the effect of cerium upon the nonmetallic inclusions found in cast and wrought steel containing various amounts of sulfur, oxygen, and nitrogen. Interest of the Physical Metallurgy Laboratory of the Watertown Arsenal Laboratories in this type of research was stimulated by the reports from industry that rare-earth metals imparted beneficial effects upon the mechanical properties of steel, but that the mechanism was not understood. Berry and Dorvel' found that misch metal improved the impact properties of aluminum-killed cast steels. They reported that the rare earths modified the intergranular-film type nonmetallic inclusion, present with aluminum as the sole deoxidant, to a randomly distributed globular type. Lilliequist and Mickelson2 observed the improvement of ductility and toughness of quenched and tempered cast steels through rare-earth additions. They also observed the change from angular to duplex inclusions when rare earths were present. They con-

Jan 1, 1960

By Alan English

INTRODUCTION During the Bicentennial Year in the United States of America, recognition should be given to the fact that 20 years ago the first large-scale commercial pelletizing plant was started and attained rated capacity. This was the beginning of a new industry. Twenty years ago the total production of pellets was principally from pilot plant facilities and totaled in the thousands of tons per year. At the present time the world production is slightly in excess of 280 million tons per year. This truly is a tremendous growth for any industry. Such a production growth obviously is accompanied by a similar growth pattern in the development of process, equipment, and facilities. During the growth and development period, different materials became more adaptable for processing. For example, initially the pelletizing of iron ores revolved around the magnetite concentrates where the heat of reaction constituted a very important part of the process fuel. During this growth period, specular hematite, earthy hematite, mixtures of hematite and magnetite, and even non-ferrous type materials were pelletized, a function previously thought not practical. The demand for the use of pellets has also broadened their concepts. At first they were made to replace the high-grade iron ores used in blast furnaces. Nowadays, not only have they replaced iron units, but they have had a major influence on the design of larger blast furnaces and have contributed to production rates in excess of 10 000 tons per day from a single furnace. They have also been used in the manufacture of steel, principally for coolants in the BOF practice. More recently, with the improved beneficiation techniques that have been developed over the same period of time, pellets have been used for the direct reduction process and can be used directly

Jan 1, 1977

By D. G. Westlake, D. T. Peterson

The saturation solubility of thorium dihydride in thorium was studied by saturation of samples and subsequent analysis. The solubility increased from about 1 at. pct at 300°C to above 20 at. pct at 800 °C. Over this temperature range the log of the solubility was a linear function of the reciprocal absolute temperature for thorium of good purity. The heat of solution of thorium dihydride was found to be 7.9 kcal per atom of hydrogen in crystal bar thorium and 6.6 kcal per atom of hydrogen in Ames thorium, The important effect of hydrogen on the physical and mechanical properties of many metals is receiving increasing recognition. The basic physical and chemical data necessary to help explain the observed effects of hydrogen on the mechanical proper ties of metals are all too often not available. The solubility of hydrogen in thorium metal was determined to provide a portion of this basic data for the thorium-hydrogen system. The absorption of hydrogen by thorium metal and the formation of thorium hydrides was studied by several investigators, beginning in 1891, and their work is summarized in Gmelin's Handbuch.1 No effort was made to determine the extent of solid solubility in the metal in these early investigations and the impure metal available made interpretation of the results uncertain. Nottorf2 reported the results of a careful study of pressure-composition isotherms for the thorium-hydrogen system. The principal interest in this work was in the composition and dissociation pressures of the thorium hydrides. Mallett and campbel13 reported the pressure-composition isotherms for the thorium-hydrogen system up to the composition of thorium dihydride. The saturation solubility of thorium dihydride in thorium was reported to be 13 at. pct at 650°C and 23 at. pct at about 900° C. Mallett and Campbell used thorium metal which had been prepared by the calcium reduction of thorium tetra-fluoride or thorium oxide. The results obtained with thorium of these two types agreed within the experimental error. PROCEDURE AND MATERIALS Procedure—The method used to determine the solubility was to saturate a sample of thorium with hydrogen and analyze a portion of the saturated sample. This method was chosen rather than a determination of pressure-composition isotherms since it was much less time consuming and could be applied at temperatures at which the equilibrium hydrogen pressure was too low to measure. The

Jan 1, 1960

By Francis T. Freeland

The deeper workings of the Leadville mines show refractory ores, consisting principally of sulphides of iron, lead, and zinc, carrying silver, in place of the easily reduced carbonate ores lying nearer the surface. The largest and most extensively developed deposit is that of South Iron Hill.* It lies on the north side of California Gulch,

Jan 1, 1886

By Donald L. Katz

Charts for predicting the pressure to which natural gases may be expanded without hydrate formation have been prepared for gases of even gravity. Pressure-temperature curves for hydrate formation were established for gases having gravities from 0.6 to 1.0. These curves and the thermal behavior of the gases during free and adiabatic expansion were used to prepare the charts for estimating the permissible expansion of natural gases without hydrate formation. The problem was solved by L. F, Albright, W. T. Boyd, J. J. McKetta, G. Martin, P. Poettman. and A. P. Snyder.-, who are first-year graduate students in the department of Chemical and Metallurgical Engineering at the University of Michigan. This paper is essentially a summary of their results. Prediction of Conditions for Hydrate Formation in Natural Gases Each natural gas under a given pressure will form solid hydrates at a corresponding temperature provided sufficient water is present.1-5 The temperature of natural gases below about 5000 lb. per sq. in. decreases when the gases are expanded freely.6,7 This decrease in temperature may cause the expanding gas to enter the region of temperature and pressure at which hydrates will form' The final pressure to which a natural gas may 'be expanded without hydrate formation depends upon the initial temperature and pressure and the gas composition. This paper presents charts that give the final pressures to which gases of gravity 0.6 to 1.0 at given initial temperatures and pressures may be expanded without formation of hydrate. Hydrate-forming Temperatures and Pressures as a Function OF Gas -Gravity Experimental data of pressure versus temperature at which solid hydrate will form, provided sufficient water is present, are available for a series of gases.2,3 A method of predicting the pressure-temperature curve for a given gas composition has been reported.' The solution to this problem requires that these curves relating pressure to temperature be established for gases of given gravities.

Jan 1, 1945

By Fred A. Anderson, George B. Wallace, Edward J. Slebir

As the reservoir rises behind an arch dam, it presses the arch into the canyon walls and valley floor. To compute the stresses, deflections, and arch reactions, it is necessary to know how much the rock deforms under the combined loads of gravity, temperature, and water. Under sustained loading for a period of time, the rock continues to deform or "creep" slightly, causing changes in the stresses and shape of the arch. Under reduced loading, the elastic arch tends to resume its unstrained position and it is important to know that the rock will follow it and maintain tight contact along the abutment. It is, therefore, important to know the "set" characteristic of the rock. Past attempts to define load-deformation properties of rock, including creep and set, have largely l been limited to laboratory test of intact cores and in-situ jacking test utilizing bearing plates 2 to 3 ft in diam. In both cases, a uniaxial load has been applied to a volume of rock too small to fully reflect the influence of cracks, joint systems, foliation, and other inherent weaknesses within the rock mass. This chapter describes a large radial jacking test which more nearly duplicates the action of an arch dam by penetrating the load deep into the rock mass, bringing into play more of the factors which contribute to prototype deformation. Results obtained from the large radial test are compared with those from smaller uniaxial test. DESCRIPTION OF RADIAL TEST The radial jacking test described in this chapter was performed in an adit off of an exploratory tunnel driven into a proposed dam abutment

Jan 1, 1972

By Chester T. Sims, Robert I. Jaffee

The thermoelectric behavior of the Pt—Pt-Re thermocouple and the resistance of rhenium to attack by certain molten metals is discussed. In addition, data are presented on the stress-rupture behavior of drawn wire, the tensile characteristics of rolled sheet, the variation of Young's modulus with temperature, and the effect of specimen size and fabrication method on the work harden ability. Mechanical properties of thoriated rhenium are discussed. This includes data on the effect of thoria in rhenium on tensile properties, ductility, work hardening, and recrystallization. RECENT work by the authors', has described methods of fabrication and some of the physical and mechanical properties of rhenium. Rhenium was established as a high melting, dense, refractory-type metal with favorable mechanical properties. In addition, Todd and co-workers' and others" have studied such properties of rhenium as the work function, specific heat, and the resistance of rhenium to the water cycle. Revelation of these and other properties has led to serious consideration for application as electrical contacts, high temperature thermocouples, and wear resistant materials. chanical properties reported previously,' several additional examinations have been conducted. The stress-rupture behavior and the Young's modulus of rhenium have been investigated at elevated temperatures. Tensile data have been obtained for rolled sheet, and a study of the relative work hardening characteristics of rod, wire, and sheet has been conducted. Variation of Modulus of Elasticity With Temperature—The Young's modulus of a % in. diam annealed rhenium rod was determined from room temperature to 880"C (1620OF). The rod, approximately 6 in. in length, was activated in a transverse vibration apparatus suspended in a furnace. The resonance frequencies of the rod were measured and used to calculate the moduli values. The driven frequency was 569 cycles per sec, and a protective helium atmosphere was used. The data, plotted in Fig. 1, show that the modulus decreases in an approximately linear manner with temperature over the range tested.

Jan 1, 1957

By Paul Merica

ALTHOUGH nickel was discovered and isolated as early as 1750 and its valuable properties recognized, many years passed before it was used commercially for wire, sheet, rods, etc., in the pure form. This was due partly to its high cost at that time and partly to the fact that it was not possible to refine and cast nickel into ingots sufficiently malleable to be amenable to the usual forging, rolling, or drawing processes. So remarkable was this fact, and so different from the experience at that time with metals such as copper and iron, that it has left its impress on the no-menclature within the nickel industry. To this day, furnace-cast nickel produced in such a manner as to be suitable for rolling and forging is called malleable nickel to distinguish it from the ordinary pig and shot nickel of commerce. In 1878, the firm of Jos. Wharton, of Philadelphia (which later became The American Nickel Works, a constituent of The International Nickel Co.) exhibited at the Paris Exhibition specimens of rolled pure nickel strip and of drawn nickel wire. About this time, there was considerable activity in the study of the refining of nickel and several methods were described, some of which were patented, for the production of furnace-cast malleable nickel including the use of manganese (Boed-dicker,1 Selve and Lotter2), the use of potassium permanganate (Bernsdorfer Metallwarenfabrik3) and the use of phosphorus (Garnier4). By far the most efficient method was discovered by Th. Fleitmann in 1879;5 it consisted in adding to the molten nickel, just before pouring the castings, from 0.05 to 0.125 per cent. of metallic magnesium. This soon became the recognized final malleableizing treatment for furnace-cast nickel.

Jan 1, 1925

By Albert H. Fay, William B. Plank

In practically all rock-excavation problem there is need for a careful study of the rock structure, its fault, cleavage or bedding planes, and even the texture of the rock itself. These studies should form the bases upon which an excavation method is selected and they should be carefully considered in predicting the amount and extent of the excavation. The need for such studies was forcibly illustrated in the problems involved in a cut made in 1929, along and underneath a 200-ft. high rock projection for a State highway near the City of Easton, Pennsylvania. The rock mass was badly faulted and also contained a number of cleavage planes at approximately right angles to the fault planes. Much of this structure was visible and could have been studied and analyzed before the work was begun. The State had rigid specifications as to finished grade and slope of cut, which apparently were made without reference to the geologic structure. The contractor complied with the specifications, under the close inspection of the State engineers. A tunnel blast was placed in the base of the cliff, with the result that 65 per cent more rock was broken than was intended by the specifications. About four years after the blast, the writers of this paper studied the circumstances surrounding the operation, to determine the cause of this excess excavation. Scope of Work The section of the roadway involved was about 200 ft. long and on a 6' curve. It was necessary to relocate points on the curve, from which all faults and cleavage planes were located and measured by the use of transit and clinometer. A plan (Fig. 1) showing the blasting tunnel, the roadway, and traces of the faults and cleavage planes on the level of the roadway, was prepared; also 13 cross-sections at varying intervals, showing the original face of the hill and the face after the blast. The original and final profiles of the rock face, taken from the plans of the State engineers, are shown in Figs. 2, 3 and 4.

Jan 1, 1937

By L. D. Jaffe, M. R. Norton, J. H. Hollomon

IN the practical heat-treatment of steel the decomposition of austenite usually occurs during cooling rather than at constant temperature. Nevertheless, the course of this decomposition has generally been studied only isothermally. Isothermal studies are not only simpler experimentally, but have the great theoretical advantage that one of the variables, temperature, is constant. It is the purpose of this paper to outline the principles that govern the relations between isothermal and anisothermal? decomposition of austenite, to present and systematize the available experimental information, and to indicate the gaps in the existing knowledge. Some of the experimental information is the result of new work. § Most of it is derived from scattered data in the literature. Many of these data were obtained incidentally in the course of research on other subjects and their significance has not been pointed out and perhaps not understood. It is hoped that this paper will aid future planning of more extensive research on anisothermal decomposition. METHOD In order to study the relations between isothermal and anisothermal decomposition, it appears fruitful to view anisothermal decomposition as taking place at a series of constant temperatures1 (except for the martensite reaction, which does not occur isothermally to an appreciable extent). When the time the steel is at each temperature is finite, the over-all amount of the reaction is considered to be the sum of the amounts occurring at each of the successive temperatures. During continuous cooling or heating, the time the steel is at each temperature and the difference between successive temperatures can be considered to approach zero. The over-all amount of transformation will then be given by integration over the range of temperatures involved. This point of view is advantageous in that it considers anisothermal transformation to be a series of isothermal transformations. The problem thus becomes one of determining the effect of partial decomposition at any given temperature upon subsequent decomposition at another temperature. Single Anisothermal Reaction Consider a phase brought to a temperature at which it is unstable, held there until it has partially transformed, and then brought to another temperature at

Jan 1, 1946

By T. S. Fuller

The work of D. J. McAdam, Jr.1,2 at the U. S. Naval Engineering Experiment Station, Annapolis, Md., on what has been called by him "corrosion-fatigue" has focussed the attention of the engineering profession in general, and of those interested especially in the study of corrosion in particular, on the importance of making tests which will indicate as nearly as possible what can be expected from a given material in service. Pitting is unquestionably the chief agent operating so tremendously to reduce fatigue limits, but in the light of previous work3, 4, 5, 6, 7, 8 it is fair to assume that absorbed hydrogen resulting from the action of the corroding medium upon steel may, under certain conditions, have a perceptible influence. The experiments described in this paper deal more precisely with stressless corrosion, or "prior-corrosion fatigue,"9 and have been carried out to test such an assumption, to segregate, if possible, the effect of pitting from that of absorbed hydrogen, and although very preliminary in nature they indicate results which are striking.

Jan 1, 1929

By T. S. Fuller

The work of D. J. McAdam, Jr.1,2 at the U. S. Naval Engineering Experiment Station, Annapolis, Md., on what has been called by him "corrosion-fatigue" has focussed the attention of the engineering profession in general, and of those interested especially in the study of corrosion in particular, on the importance of making tests which will indicate as nearly as possible what can be expected from a given material in service. Pitting is unquestionably the chief agent operating so tremendously to reduce fatigue limits, but in the light of previous work3, 4, 5, 6, 7, 8 it is fair to assume that absorbed hydrogen resulting from the action of the corroding medium upon steel may, under certain conditions, have a perceptible influence. The experiments described in this paper deal more precisely with stressless corrosion, or "prior-corrosion fatigue,"9 and have been carried out to test such an assumption, to segregate, if possible, the effect of pitting from that of absorbed hydrogen, and although very preliminary in nature they indicate results which are striking.

Jan 1, 1929

By W. J. Carlson, S. M. Parmerter, I. Iwasaki

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates. It also deals with the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when an-ionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were affected most strongly by the level of starch, to a lesser degree by the pH, and virtually not at all by the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semitaconite could be readily attained with starch and calcium chloride. A previous article discussed some of the parameters that are important when various corn starches are applied to the soap flotation of activated silica from iron ores and to the flocculation of iron ore slimes.' Methods of solubilizing the starches and the molecular size after mechanical and thermal treatments, as inferred from the viscosity measurements, were shown to influence the adsorption characteristics on iron ores, and the residual concentrations of both calcium ion and starch in the pulp liquor were in direct correlation with the flotation and flocculation behavior.2-4 The present article summarizes the results of more recent tests conducted to ascertain the role of starches and starch derivatives in various phases of iron ore beneficiation. The scope of this investigation has been extended to include not only anionic and cationic flotation, but also the flocculation and filtration of iron oxide slimes, the selective flocculation and partial upgrading of semitaconites, and the flocculation and clarification of magnetite-taconite tailings —all problems that are of vital importance to the iron ore industry of Minnesota. By combining a practical approach with adsorption studies and by using single-mineral systems5 in these research efforts, it is believed that the ultimate goal of developing a suitable modification of starch structure may be realized. The topics covered in this article are limited to the empirical aspects of the research program on the depressant activity of starches and products in the cationic and anionic flotation of silica and of their role in flocculation, water clarification and filtration. ANIONIC SILICA FLOTATION In the soap flotation of activated silica from iron

Jan 1, 1970

By A. F. Meger

Coal treatment by oil spraying receives special attention at the Georgetown plant for the dividends it pays in satisfying present customers and attracting new markets. Customer satisfaction requires care, quality control, and use of suitable oils. REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal CO. who have helped develop, over a number of years, an efficient and flexible method for spraying controlled amounts of oil on coal. Since the Georgetown preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage. The graph, Fig. 1, shows results of the original tests made with a 700-sec residual blend and a 500-sec lubricating oil on Georgetown stoker coal of 1¼x3/8-in. size.* The advantages of better price, improperly blended can raise havoc. Some.,pale oils also, although odorless when delivered, give off a sweet sickening odor when atomized under pressure. It is recommended that all products be tested before they are used. There is a specific place for all spraying oils. For example, at a power plant a severe dust condition exists around the stockpile area and in parts of the plant. The cheapest spraying oil made, regardless of odor, will do an excellent job in this case and will save the company 3 to 5c per gal or more. Domestic trade, on the other hand, must be carefully handled to prevent complaints about odor, and the only way to do this is to stay with the proved products after the odor tests have been made. The preparation plant at Georgetown has facilities to handle either tank car or tank truck deliveries. Steam is available at the unloading point if the weather is severe, and there is an indicator at the unloading point to prevent overflowing the 20,000-gal underground storage tank. Systematic test samples are removed from each delivery and sent to the lubrication engineer to insure quality control. Fig. 3 illustrates the chutes in which smaller sizes of coal are treated. Fig. 4 shows the entire spraying system. Buried in the ground is a 20,000-gal tank with immersion heaters grouped around the feeder line to insure adequate gravity flow to the pump under all conditions of weather. Oil flows to a 500-gal preheating tank where the temperature is kept about 150°F by six 1½-kw immersion heaters thermostatically controlled. Hot oil is fed through a self-cleaning disc-type filter to the hydraulic pump. Valves and piping make it possible to transfer oil from one tank to another or to drain the lines for maintenance purposes. All this equipment is below ground level in a covered pump room,

Jan 1, 1955