Search Documents

By E. M. Bennett

HISTORY In 1923 John Campbell Miles discovered the Mount Isa deposit after finding and submitting for assay some “unusual and heavy rocks”. Six months after submission he received the assays of his original samples which indicated high lead-silver values. The deposit area was isolated and unknown geographically and not served by even a rough country road. The isolation of Mount Isa coupled with the depression years had a strong influence on the rate of development of the area. These two factors resulted in a slow amalgamation of the early individually held leases and the lack of ready finance to begin serious mining of the deposit. Initially, surface lead-silver-zinc mineralisation was proved and diamond drilling to shallow depths showed the presence of a viable orebody. Limited underground development work was initiated and open cutting associated with glory holing commenced. Due to the metallurgical problems associated with the ore and due also to unsuspected change in metallurgical conditions as the ore deepened into what is known today as the transition zone, major problems of finance were recurring at frequent intervals. Despite low metal prices the development of the mine continued due to continuing infusion of capital. During the 1939-45 war years a surplus of lead was being produced in Australia, but a grave shortage of copper was apparent. About this time copper ore had been found to the hanging wall of the then known major lead orebodies. At the request of the Australian Government, lead production ceased and copper production commenced.

Jan 1, 1970

By C Gunther

A preceding paragraph treats of the irregular manner in which ore deposits occur and the complex factors that control their distribution; the occurrence of metals in oreshoots in individual deposits is equally irregular, and the factors that control such segregation are equally complex. While the dimen¬sions of oreshoots in individual deposits may not be foretold with any degree of accuracy, the occurrence of ore in shoots is not accidental, but is controlled by laws some of which are understood. Any one familiar with permutations and combina¬tions who stops to consider the variety of factors that control ore deposition, and their varying relative importance, will admit that the science of economic geology must advance greatly before the occurrence of oreshoots may be predicted accurately in advance of exploration. The segregation of minerals in any oreshoot must be referred to some condition, or combination of conditions, local to the oreshoot as compared with the remainder of the deposit of low¬grade or barren minerals. Among the localizing factors that have been recognized are, in filled fissures, the amount and distribution of open spaces available for ore deposition, and in replacement deposits, the degree of brecciation giving access to the replacing solutions; the intersection of veins with other veins, dikes, sheeted zones, or porous strata; the impounding of solutions by impervious strata; and the differing precipitative influences of enclosing rocks. A large proportion of important and well ¬defined oreshoots, especially in deposits of deep-seated origin, are not assignable to any of these factors. While a knowledge of the character of oreshoots in general is important, a knowledge of the behavior of the known oreshoots

Jan 1, 1932

By P. G. Chamberlain, E. R. Podnieks, R. E. Thill

Although published data on the physical properties of rock are voluminous, information is often lacking on the environmental conditions under which such data were acquired. Efforts are frequently directed to improve specimen tolerances and preparation procedures; but investigators often overlook giving the rock environment equally careful control during the testing program. Generally, tests are conducted at existing laboratory room conditions, and the prepared rock specimens are frequently, if not most commonly, air-dried for various lengths of time before testing. The standard testing atmosphere recommended by the American Society for Testing & Materials (ASTM)1 is 73.4°F and 50% relative humidity. To maintain a rock at 50% relative humidity for testing purposes, however, requires special equipment and preconditioning procedures, as this study demonstrates. Relatively small variations in the moisture content of a specimen, for example, due to the coolants or lubricants used during specimen preparation, can cause significant variations in the physical properties measured. Such moisture variations may occur in the rock specimen even after it is air-dried, since laboratory humidity conditions commonly fluctuate from day to day. For these reasons, this study emphasizes procedures for preconditioning and maintaining a controlled environment during testing. Although the effects of moisture or temperature on rock properties have previously been studied, their combined effect on rock properties is unknown. In this study, uniaxial compressive strength, Young's and stiffness moduli, and longitudinal wave velocity were determined and compared under controlled conditions of temperature, moisture, and pressure for 11 environments considered to be of particular interest in laboratory, in-situ, and even simulated lunar environments. The following environments were selected for this program: -250°F under dry, 50%

Jan 1, 1972

By James E. Lawver

Efficiency of industrial research and development depends on the ability of engineers and scientists to collect and present data to top management for decisions. In many cases, the data presented are so deceptive that management makes costly wrong decisions. Since management personnel often are selected on the basis of higher administrative quality than technical ability, it is the responsibility of the industrial scientist or research engineer to make certain that the data presented tell a completely ac- curate story of each industrial problem. It is rare that misleading data are deliberately presented, but when this is done, it is? of course, dishonest. The rise of deceptive data usually stems from the lack of knowledge of experimental design and statistical methods of analysis. Most of the better chemical engineering schools have recognized the need for courses in industrial experimentation and many of them offer complete courses at both graduate and un- dergrarluate levels. By contrast, many of the mining and metallurgical schools have not recognized the importance of industrial experimentation courses and some of them, in fact, do not allow credit toward a mining or metallurgical engineering degree for statistical courses even when taken as an elective. The sole purpose of this paper is to make a plea for mining and metallurgical schools to present required industrial. statistical courses for their graduates. It is true that fine industrial research has been accomplished in the past without the assistance of any statistical techniques. Industrial problems have also been solved without the use of digital or analog computers, electron microscopes or other modern conveniences. The fact remains, however, that the correct use of these modern tools tends to reduce the cost of research and to eliminate costly errors. A working knowledge of experimental design and statistical data analysis must simply be viewed as a valuable tool whose proper use will greatly reduce the cost of experimentation and minimize the cost of false conclusions. These statistical methods, however, simply cannot replace fundamental knowledge or, for that matter, "good horse sense". Nevertheless. an experimenter armed with fundamental knowledge and good horse sense but completely ignorant of elementary statistical techniques, may easily present his data in such a deceptive form to cause management to make incorrect decisions.

Jan 6, 1962

By R. E. Somers

1. INTRODUCTION 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant County. The group is made up of two distinct moun-tain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City-, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy down-pour of rain. . The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 5, 1915

By W. H. Emerson

In the summer of 1894, a specimen of corundum from Acworth, Ga., which mas reputed to be of markedly inferior quality for the manufacture of corundum-wheels, was received by the Geological Survey of Georgia, with the request that it be analyzed, in order to ascertain whether this inferiority was associated with any peculiarity of composition. In its appearance there was nothing uncommon, though it seemed to be rather easily scratched with a knife, while, at the same time, it scratched agate easily. An analysis gave the following results: Alumina, 94.58; silica, 1.77; magnetic oxide of iron, 0.69; calcium oxide, 0.44; and water, 2.51 per cent. There is nothing unusual in this composition, except the amount of water, which is usually, in southern corundum at least, from 0.3 to about 1 per cent. Concerning this corundum, the Mineral Resources of the United States, 1893, pp. 676 and 677, Bays: "It is supposed that this variety of corundum contains a little water, as it is

Jan 1, 1900

By A. E. Bellis

THERE is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat-treatment, structure, and physical properties. In order to promote discussion, which it is hoped may lead to the discovery of the source of 'some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat-treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.1 The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08. per cent. The minimum physical requirements are: Tensile strength,- 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirement's gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in- the best heats of open-hearth steel, so that' faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at, a proper temperature clown to the form of tapered barrel blanks or by heat-treating bars that have been upset to enlarge the breech section. The transformation temperature of this steel, on heating, is around 1350° F. (732° C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different

Jan 7, 1919

By J. B. Austin

IN developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measure-ments serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transforma-tion temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chro-mium or managanese. The lag, or undercooling, observed at the ? - a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,1 using a rate of heating and of cooling of 3.0° to 3.5° per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2

Jan 1, 1935

By W. A. Griffith

The fundamental principles and modern techniques of experimental planning and data analysis, applicable to any type of research, are particularly important in flotation experimentation. Since they constitute the modern science of experimentation, they should be among the working tools of any scientist, research engineer, or plant operator engaged in flotation investigates. This chapter is a review of these principles and techniques. Equipment and procedures for the actual conduct of experiments will not be discussed here since these subjects are well covered elsewhere in this volume. Neither will any attempt be made to impart a working knowledge of statistical methods of data analysis since this would be impossible in the space allotted, and many excellent texts are available to the diligent inestigator.1-4 The objective here is simply to interest the reader in the application of statistical techniques to flotation experimentation by illustrating their utility in situations frequently encountered, and to point out the principles of experimental planning necessary for their proper use. Any conscientious metallurgist engaged in flotation experimentation or operations is well aware of the inherent complexity of the flotation process, and of the often frustrating difficulties this introduces into experimentation. The raw materials normally treated by the process are complex both physi- cally and chemically, and often highly variable even when from the same source. The flotation process itself is characterized by a very large number of potentially important process variables. Many of these are beyond the con- trol of the metallurgist, and some cannot even be measured quantitatively with available instruments. Those which can be measured and controlled with reasonable precision often produce effects which are intricately interrelated. Not only are the variables many, but the physical and chemical mechanisms by which they function are imperfectly under stood. To compound the difficulty, experimental techniques are relatively crude. Controls are not very precise, and the human factor looms large in most flotation experiments. These situations lead inevitably to experimental data of a relatively low degree of precision or reproducibility. Some are inclined to think that these conditions are unique to flotation experimentation. They are not. The experimental problems met by the agronomist, the biologist, the social scientist, and others are equally complex. Investigators in these fields pioneered in the development of methods for handling just such situations by proper experimental planning and the application of statistical methods in the analysis of data. Their pioneering work has grown into a well established modern science of experimentation which has spread into every field of science. This science is based upon statistical

Jan 1, 1962

By J. J. Bowman, E. H. Dix

A lack of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investigation an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100" C. are too small to be of practical importance. Introduction The technical literature contains numerous papers describing die castings, their production, compositions and uses, but nearly all of these

Jan 1, 1935

By J. J. Bowman, E. H. Dix

A lack of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investigation an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100" C. are too small to be of practical importance. Introduction The technical literature contains numerous papers describing die castings, their production, compositions and uses, but nearly all of these

Jan 1, 1935

(SECRETARY'S NOTE.) The following discussion of the papers of Van Hise, Emmons, Lindgren and Weed, read at the Washington meeting, February, 1900, and printed on pp. 282 to 498 of this volume, comprises communications to the Secretary, received at various times before the Richmond meeting, February, 1901, and, for the most part, presented at that meeting. These communications are introduced at this point in the present volume, in order that they may precede the papers of Vogt, hemp, Lindgren, Rickard, etc., presented at Richmond, and therefore not forming part of the material considered in them. Since many of the contributors have mentioned in one communication several of the papers referred to, no attempt is here made to divide their remarks and distribute the fragments under separate headings. In each contribution, however, the several topics are indicated by subtitles. R. BECK,* Freiberg, Saxony : Prof. Veal Hise's Paper.-The paper of Prof. Van use (p. 282) represents a great step of scientific progress, in that the circulation of underground waters has never before been presented with such clearness, ill the light of modern chemical and physical knowledge. The theories of the formation of ore-deposits which follow the author's general survey of the currents and solvent power of atmospheric waters in the earth's crust do not, indeed, seem to be novel, being essentially an amplification of Le Conte's views; but the proofs adduced in their support are in many particulars so original that no one can read without profit this portion of the paper. Entirely new (though largely in agreement with the papers of Emmons and Weed, presented at the same meeting of the Institute) are the sections dealing with the formation of the rich sulphides of the precious metals, and especially the regeneration of normal sulphides, such as galena, etc., in vein-zones immediately beneath the ground-water level. Nevertheless, it appears to me that Prof. Van Hise, in the course of his most instructive exposition of unquestionable, yet still locally limited, phenomena, has been too much biased in favor of the " descensionists." This is indicated by the small importance which he attaches to the intimate genetic relation between epigenetic deposits and the plutonic hearths of the earth's interior.

Jan 1, 1902

By H. W. Gudenau, R. S. Chatty, W. Wenzel, M. Ponthenkandath

During several experimental programs conducted at the Institute of Ferrous Metallurgy, Technical University, Aachen, whisker formation was observed when iron ores were reduced at low as well as at high temperatures. Thus, in an attempt to find the reason for the volume change taking place during reduction, iron whisker growth was observed. Whisker growth appears to be one of the important reasons for the swelling of pellets. One set of experimental observations determined that when iron forms as needles rather than as a crust on the surface of oxide, the pellets became very porous. In related experiments, the beneficiation of finely disseminated iron ores, in which the metallic iron is separated from the gangue in granular or nodular form, was achieved by a reduction-concentration method. In this process, which is conducted at sufficiently high temperatures, oxide whisker growth, resulting from the formation of volatile suboxides and a gas transport mechanism, plays a vital role in the joint deposition of SiO, and iron from the vapor stage.

Jan 1, 1973

By J. L. Fitch, B. G. Hurd

The presence of gypsum in samples subjected to standard core analysis introduces serious errors in the measurement of water saturation and porosity. The magnitude of these errors, depending upon the type of analysis procedure used, has been evaluated experimentally and theoretically. Water-saturated pore volumes determined by vacuum distillation or retort procedures may be too high by as much as 48 per cent of the volume of gypsum present. The maximum error in this value determined by Dean-Stark extraction with toluene is 36 per cent of the gypsum volume. If pore space is measured by a Boyle's law type porosimeter the maximum erorr due to gypsum is 38 per cent of the original gypsum volume present. The conscientious core analyst may eliminate the errors caused by gypsum by either of two methods. He may apply suitable corrections for the water of crystallization removed from gypsum, or take special precautions to prevent dehydration of gypsum during core cleaning and alzalysis procedures. These alternatives are discussed and methods for obtaining reliable core analysis data are proposed. Gypsum (CaSO4 . 2H2O) occurs as a common mineral in many of the world's sedimentary basins. In addition to its presence as primary bedded evaporitic deposits, it is often found as secondary replacement zones and pore-fillings in host rocks. That it may cause false indications in porosity, both on neutron logs and in standard core analysis, has been generally recognized. False porosity interpretations from neutron logs result because the chemically bound water in gypsum attenuates neutrons as effectively as free water. Errors in core analysis result when gypsum is dehydrated prior to or during the analysis. Vacuum retort procedures used by many laboratories to determine fluid saturation and porosity effect a complete removal of water of crystallization from gypsum. The crystal water, distilled and collected with free water from the sample, is counted as water-sat11rated pore space. Dehydration of gypsum results in a decrease in volume occupied by calcium sulfate and a corresponding increase in pore volume. Thus, if gypsum is dehydrated by sample cleaning and drying procedures, subsequent porosity measurements with gas expansion or compression instruments will be high. The qualitative effect of gypsum on porosity determinations by retort procedures was discussed in a recent article by Bynum and Koepl3. They concluded that since false porosity was interpreted as being water saturated, determinations of oil content were not affected. Others in the industry, however, have pointed out that porosity values are often used with values of water saturation determined independently, e.g., from electric resistivity logs in making reserve estimates. Values of water saturation calculated from the formation resistivity using the Archie equation, S4= are actually low if values of are high due to gypsum. In this case, false porosity values due to gypsum could cause serious errors in calculations of oil-in-place. This investigation was made to determine quantitatively the effect of gypsum on porosity values determined by different core analysis procedures. EXPERIMENTAL PROCEDURES Dehydration of Gypsum The extent and rate of removal of water of crystallization from gypsum under conditions encountered in core analysis procedures were studied. Taken for the experiments were three types of relatively pure, naturally occurring gypsum, viz. selenite, satin spar and massive gypsum. Although all samples probably contained trace chemical impurities, each type lost the theoretical amount of water upon complete dehydration. An automatic recording thermobalance, similar to one described by Mauer2, was used to obtain dehydration rate data for samples heated in dry air. Water

By N. O. Johnson

THE Hog Mountain mine is a pyritic-gold property in the north central part of Tallapoosa County, Alabama, at an elevation of 800 ft. in the southern Appalachian region. It is 13 miles by a good secondary road from Alexander City, a station on the Central of Georgia Railroad. Since its discovery in 1839, the mine has been worked intermittently. The records of past operations are few and are scattered over a long period of time; however, available information indicates a production of approximately 12,000 oz. of gold prior to the present company's activities, which started in 1933. Additional 7844 oz. has been produced under the direction of the present management. The ore from stopes has averaged 0.200 oz. gold per ton; the ore from development, 0.136 oz. gold per ton. Silver, copper, iron and sulphur are also present but to date are of minor importance. The grade of ore in comparatively narrow veins makes necessary extreme vigilance in the methods of mining. Geology Wall Rock.-Hog Mountain consists of a quartz-diorite intrusion approximately 5000 ft. long by 1200 ft. wide. Its resistance to weathering, as compared to the surrounding schists, has led to the formation of a conspicuous ridge rising 400 ft. above the adjacent country. All the mining operations are confined within the limits of this quartz-diorite formation. . Except where there is excessive shearing, either parallel or at flat angles to the quartz veins, all the walls of the stopes within the limits of the veins are strong enough to make timbering unnecessary. Where shearing exists, there may be a sloughing off of the walls, especially in the process of drawing the ore. When this occurs, stulls are placed in the stope, either while the stope is advancing, or while ore is being drawn from a completed stope. In general, very little timber is required. Veins.-The quartz veins have been deposited along fracture planes in the quartz diorite. There are 20 principal veins, all of which are roughly parallel and strike at right angles to the long axis of the formation.

Jan 1, 1937

By R. T. Gallagher, C. G. Brennecke

This paper is the result of a research program entered into cooperatively by the General Reinsurance Corporation and Lehigh University in January 1944. The research program was instituted to find a more positive method to determine the presence of hazardous roof conditions in mining operations. The co-authors, together with Mr. R. D. Currie, Engineer for the General Reinsurance Corporation, started working on the project in January 1944, first undertaking a library search; second, a preliminary study based on some existing equipment; third, the design of new and more suitable equipment; and finally, the field testing of equipment and methods. PURPOSE Any study of the accident statistics of mining operations will disclose the rather startling fact that approximately 50 to 60 per cent of all fatal underground accidents in the anthracite and bituminous mines are caused by falls of roof and coal, the metal and nonmetal mines showing only a slightly smaller percentage. Advancements in safety engineering have produced definite results in the decrease of accidents due to blasting, haulage, electricity, and explosions but no such decrease is shown in those caused by falls

Jan 1, 1946

By M. N. Dunlap

This article summarizes the successful incorporation of a flash-flooding stream into the tailing-disposal system at the St. Joseph Lead Company's Federal Division mill, in St. Francois County, Missouri. The mill was built in 1906, by the Federal Lead Co., as its No. 3 mill for the concentration of southeastern Missouri lead ores, and damming Davis Creek was first considered in 1908. Plans were made also in 1925 and in 1937. Dam layouts varied from a reinforced concrete structure to a barrier built of tailings alone. .All were abandoned because of liability that would be incurred by flash-flood rupturing of an incompleted dam. By 1942 mill capacity had reached 12,000 tons daily and increasing tailing-disposal costs again focused attention on the Davis Creek basin. This time the problem of riskless dam building was solved. Moreover, most of the items that appeared in the answer were materials that normally required wasting and the major portion of labor involved performed functions that it mould normally have done, without constructive benefit, elsewhere. The new layout also made possible advantageous changes in mill-water supply pumping; static head being reduced from 514 ft to 9; ft, friction head from 4900 ft to 2860 ft, and pumping can be done now at periods of low power demand. The following facts about the Davis Creek watershed explain the 36-year reluctance to reach these, and other, benefits. Size: 3600 acres. Outline: roughly pear-shaped, 21/2 by 3 miles at the largest dimensions. Topography: mostly hill land with steep valleys. Relief: 760 minimum to 1153 maximum. Maximum rainfall: 3.36 in. per hour. Permanent water: none natural. Now 2200 gpm discharged through 16-in. drill hole from mine pumps underground. Geology: the 17 acres near dam centerline is Bonne Terre dolomite covered with sand and gravel eroded from Pleistocene beds that cap some of the hills. The remainder of the pond basin is on Davis shale. Soil cover: mostly second-growth timber with some abandoned fields; all subject to careless burning, which reduces water-retaining ability. Flood history: flash-flooding that had taken at least one life. Downstream values: two railroad bridges before creek intersection with Flat River. Immediately below confluence, a highway bridge, a low-water crossing, a few business establishments and several blocks of residences. In July 1942 the following segments of an ingenious plan were put into operation. A ditch 270 ft long, 16 ft wide and 51/2 ft deep was excavated to bedrock in the gravelly soil along the proposed dam's centerline. This excavation, which exposed many gravel-filled channels, was run full of slimes drawn from a riser set in the top of an adjacent tailings-disposal

Jan 1, 1949

By W. Jolley

Decarburized iron and Fe-3.28 pct Ni alloys were impact and tension tested in the temperature range of ambient to 4°K. It was found that alloying with nickel improves the fracture properties of the ferrite matrix. The improvement in toughness of iron alloyed with nickel is attributed to the effect of the nickel addition on the temperature and strain rate dependence of the yield stress as well as on slip behavior. The Fe-Ni alloy exhibits wavy slip when strained at temperatures down to at least 50°K. This behavior contrasts with that of the unalloyed iron where a change It is a generally accepted fact that of the common alloying elements of steel only nickel and manganese improve both the room-temperature yield strength and the notch impact properties. It has been argued for a number of years that manganese refines the ferrite grain size, the pearlite spacing, and the grain boundary carbides in medium- and low-carbon steels and thereby increases resistance to brittle fracture.''' This hypothesis recently was confirmed for a 0.04 pct C iron containing manganese, but at the same time from wavy to planar slip occurs at about 120°K. The observed lower temperature and strain rate dependence of the lower yield stress in the Fe-Ni alloy as compared to the unalloyed iron may be attributed to this difference in slip behavior. In contrast to suggestions published previously, transmission electron microscopy showed that the uniform dislocation distributions and the lack of dislocation tangles which are produced by low-temperature straining of bcc materials cannot be attributed to the absence of cross slip at these temperatures. no increase in notch toughness was observed in a decarburized Fe-Mn alloy.3 It thus appears that manganese only increases the toughness of Fe-Mn-C alloys by refining grain boundary carbides and has no toughening effect in carbon-free iron. On the other hand, the mechanism whereby nickel improves toughness has not been established. Hodge et a1.4 have clearly shown that a 3.28 pct Ni addition lowers the impact transition temperature of 0.02 pct C steel approximately 35°C when the grain size is maintained constant. Recently, Wullaert and Tetelman6 stated that nickel refined the grain boundary carbides of an Fe-C alloy and consequently increased the toughness. They also observed the previously reporteda-'

Jan 1, 1969

By B. H. Bergstrom, A. P. Cohen, D. W. Fuerstenau

B.H. Bergstrorn (Research Div., Allis-Chalmers Mfg. Co., Milwaukee, Wis.) — Fuerstenau and Cohen have concluded from our study of single particle crushing, which had suggested that the size moduli of the crushed specimens were determined by the specific energy expended independent of feed size, that the same independence with respect to feed size exists for the specific energy-product size relationship for rod mills. They present data supporting this conclusion. Our single particle crushing experiments were on single spheres of soda-lime (type of glass was not given in our study) glass for which the feed size can truly be neglected. However, the feed size cannot be neglected in any case where the effective size modulus of the feed is not too much coarser than the size modulus of the product. This can be illustrated in the second experi- ment of Fuerstenau and Cohen where the feed is considered to be the original -6 +%mesh material. However, one can also consider the product from the 7.5-min grind to be the feed for the 10, 15, 20, 25-min grinds, and the 10-min product to be the feed for the 15, 20, 25-min grinds, etc. If the specific energy-product size moduli curves are drawn for these other feeds, as shown on Fig. 3, the new curves (and some curvature is apparent) are much steeper than the -6 +%mesh feed line. The slopes of these new curves are about -1.5, —1.8 and -3.0. This observation is in accord with the observation by Bond, who states that the net specific energy input to a grinding mill is equal to the specific energy represented by the product less the specific energy represented by the feed. Bond presents, on a diagram similar to Fig. 3, a series of curves which illustrate the effect of

Jan 1, 1963

By Alfred H. Bell

The year 1937 has been outstanding in the history of the Illinois oil industry. During the course of the year the state's daily production has been trebled, increasing from 12,000 bbl. per day at the beginning to 37,000 bbl. per day at the end, and the year's total, 7,426,000 bbl. is 66 per cent above the previous year's production of 4,475,000 bbl. The production in January was 368,000 bbl.; in December it was 1,085,000. Production from the old fields increased slightly. Most of the new production is from fields in the central part of the Illinois Basin, an area that for many years was considered unfavorable to the occurrence of oil and gas. The principal producing horizon of the new fields is the McClosky "sand," an oolitic limestone in the Ste. Genevieve formation of lower Mississippian age. Although development has not yet gone far enough to permit accurate estimates of oil reserves in the new fields, it is believed that they are of the order of 100,000,000 barrels. The following are the oil fields discovered in 1937 listed in order of amount of daily production at the end of the year; Noble (Richland County), Clay City, including Southeast Clay City (Clay and Wayne counties), Patoka (Marion County), New Centralia (Clinton County), Olney (Richland County), Cisne (Wayne County),.Beecher City (Fayette County), and Rinard (Wayne County). One gas field, the Russellville, in Lawrence County, was discovered in 1937. For locations of the new fields see Fig. 1. A generalized geologic column for Illinois, showing producing horizons in the new fields, is given in Fig. 2. The total productive area of the new fields at the end of 1937 was 1712 acres, in which 230 wells were producing. Thisrty-five dry holes were drilled within 1/4 mile of producing wells. At the end of the year there were 19 drilling wells, 28 rigs standing, 18 rigging up and 4 new locations in these fields. In the whole state 447 wells were completed, of which 284 were oil producers and three gas producers. Total initial daily production of

Jan 1, 1938