Search Documents

By J. Norman Bulkley

As electrical power is used to a greater extent on the Rand than in any other mining center, it is thought that a short description of the methods used and results obtained may be of interest. In comparing Rand practice with that on other fields, several general factors should be borne in mind: First, the mines are all working on large tonnages of low-grade ore (average. $6.50). The annual crushing rate is about 27,000,000 tons. Second, the mines are all grouped udder the financial and engineering control of mining houses, so that the results of a group, rather than an individual mine, are open for study, and practice follows more uniform lines. Third, coal of fair quality (about 12,000 B.t.u.) can be obtained for $2 to $3 per ton., Good supplies of condensing water are, however, scarce, and have to be carefully stored. Power Supply Power is supplied by the Victoria Falls & Transvaal Power Co., Ltd., and its subsidiary, the Rand Mines Power Supply Co. Both companies, which are practically one from an engineering point of view, operate the following stations, all feeding into the same system.

Jan 2, 1916

By Bernard York, John J. Reed

Mine opening stability was investigated by loading model openings to failure. Eight-inch plaster blocks were cast with small uniform section openings passing through the centers. After curing, the models were jacketed and loaded hydrostatically in a closed vessel. Opening size, shape, and orientation were varied to determine how these factors influence opening stability. THE investigation described in this paper is a continuation of a project begun in 1946 by Bernard York and W. E. Bush. .The experimental method used in the investigation involves the hydrostatic loading of a model mine opening to failure. Most investigators agree that this loading closely approaches actual conditions in very deep mines. The conditions are further idealized by using an essentially isotropic model material. The experiments consist of casting 8-in. plaster cubes, or 8-in. diam cylinders 8-in. long, having a relatively small uniform section hole passing through their centers. After thorough drying, the models are jacketed in a flexible plastic bag and loaded hydrostatically with water in a closed vessel. At about 300 to 500 lb per sq in. pressure the central opening fails. The fracture pattern resulting from opening failure is studied in a plane normal to the longitudinal axis of the opening. The model block is sawed through its center after loading to expose this plane and to eliminate the possibility of end effect. By changing

Jan 1, 1954

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By T. Egleston

THE manufacture of charcoal in kilns was declared many years ago, after a series of experiments made in poorly constructed furnaces, to be unprofitable, and the subject is dismissed by most writers with the remark that in order to use the method economically the products of distillation, both liquid and gaseous, must be collected. It is asserted with truth that the number of kilns required for a large production of iron would be so great that it is doubtful whether any works would be justified in making the necessary outlay for their construction, but it can also be asserted with equal truth that for any such production in a given locality the use of charcoal as fuel would be equally unjustifiable. It appears to have been forgotten that there were other manufactures besides iron in which large amounts of charcoal were used, but these consumers seem to have been guided entirely by the results of the experiments of the iron men, who necessarily made the largest quantity of it. Some authors speak in a doubtful way of the quality of the charcoal produced, and a few concede that with great care good charcoal can be made in kilns, but that most of the workmen do not like kiln charcoal. This is the real secret of the opposition to this method of manufacture. Most of these objections were written when charcoal was the most important fuel used by the iron manufacturer, and when what was a large production of iron for several furnaces was less than that produced by a single modern one, in localities where other fuels can be had. Almost all that has been written on the subject related to the use of the fuel for the manufacture of iron in the blast furnace, where very peculiar properties are required, and where the quantity produced is limited by the height of the furnace, and this in turn by the crushing resistance of the charcoal. A large production was, therefore, only possible when the best and hardest woods were used. Of all these objections there is not a single one which is not equally applicable to any method of charcoal manufacture, whether it be meilers, pits, or furnaces. Until recently, therefore, the manufacturers of charcoal iron * Read at the Pittsburgh meeting, May, 1879.

Jan 1, 1880

By Frank G. Norris

Slag control is adjustment of the composition of the slag, especially with respect to the FeO content. The theoretical method of slag control would be to charge a mixture of pig iron and scrap of given composition into the furnace, to melt always at the same carbon, and, after a uniform ore addition, to tap with a constant slag composition. Such conditions are not even approximated. Both scrap and pig iron are of variable, and, in many cases, unknown composition. The charge is oxidized to a variable extent during melting. The result is that the FeO content of the slag, and consequently of the metal at tap, varies over a wide range. In order to make a nearly uniform product, this variation must be compensated for in some way. One way is to adapt the ladle deoxidation to the requirements of the metal. The other is to control the slag. In a general sense slag control may be considered as a method of compensating for variations in the composition of the charge and in oxidation during melting. The method of slag control for low-carbon steel was developed by Dr. Herty at our Butler plant3. Use of this method enables the furnace operator to tap heats at a more nearly constant FeO content and, therefore, to use a more nearly uniform deoxidation practice. The desired FeO and the accompanying deoxidation will depend on the application of the product. This statement implies that 0.10 carbon steel finished with a 15 FeO slag may be essentially different from a 0.10 carbon steel finished with a 30 FeO slag. In making low-carbon steel, the desired carbon places a lower limit on the FeO content of the slag, because the slag must be sufficiently oxidizing for proper carbon elimination. With this degree of oxidation, the phosphorus specification is met without difficulty, and there is little danger of phosphorus reversion. Thus a limiting factor in high-carbon heats is of slight importance in low-carbon heats. For heats of 0.05 to 0.07 per cent carbon, the FeO content of the slag may be controlled at

Jan 1, 1935

By Frank G. Norris

Slag control is adjustment of the composition of the slag, especially with respect to the FeO content. The theoretical method of slag control would be to charge a mixture of pig iron and scrap of given composition into the furnace, to melt always at the same carbon, and, after a uniform ore addition, to tap with a constant slag composition. Such conditions are not even approximated. Both scrap and pig iron are of variable, and, in many cases, unknown composition. The charge is oxidized to a variable extent during melting. The result is that the FeO content of the slag, and consequently of the metal at tap, varies over a wide range. In order to make a nearly uniform product, this variation must be compensated for in some way. One way is to adapt the ladle deoxidation to the requirements of the metal. The other is to control the slag. In a general sense slag control may be considered as a method of compensating for variations in the composition of the charge and in oxidation during melting. The method of slag control for low-carbon steel was developed by Dr. Herty at our Butler plant3. Use of this method enables the furnace operator to tap heats at a more nearly constant FeO content and, therefore, to use a more nearly uniform deoxidation practice. The desired FeO and the accompanying deoxidation will depend on the application of the product. This statement implies that 0.10 carbon steel finished with a 15 FeO slag may be essentially different from a 0.10 carbon steel finished with a 30 FeO slag. In making low-carbon steel, the desired carbon places a lower limit on the FeO content of the slag, because the slag must be sufficiently oxidizing for proper carbon elimination. With this degree of oxidation, the phosphorus specification is met without difficulty, and there is little danger of phosphorus reversion. Thus a limiting factor in high-carbon heats is of slight importance in low-carbon heats. For heats of 0.05 to 0.07 per cent carbon, the FeO content of the slag may be controlled at

Jan 1, 1935

By Wolfgang O. Gluschke

INTRODUCTION Virtually all countries have general legislation covering most aspects of mining and mineral processing, including investment and tax laws, safety and health regulation, and specific rules applying to exploration reporting procedures. Yet most developing countries negotiate individual agreements with foreign investors for major mineral projects, in particular when all or part of the expected output is exported. Such agreements are known under several different names, as for example concession agreement; technical assistance agreement or service contract; management agreement; production sharing contract; joint venture; or contract of work. The objectives and conditions governing such contracts are as diverse as these titles are. While a mining project is only one among a large mumber of similar undertakings in industrial countries, in most developing countries such projects usually have a dominating position within the country's economy. The general legislation is often inadequate and insufficiently detailed to cover all aspects of large projects with extensive foreign inputs and international markets. Therefore, the need for specific arrangements. Specific arrangements may also become necessary due to the complexity of markets for mineral products, the large number of participants - equity partners, suppliers, financial institutions, buyers, etc. - or economic and political conditions in the host country and fiscal regulations in the home country of the investors. Most agreements are concluded between governments, or government agencies, in developing countries and private industry headquartered in developed market economies - Canada and the United States of America in North America, Western European countries, Japan, South Africa and Australia - or, in some instances, with state-owned firms in these countries. There are fewer agreements between developing countries and the centrally planned economy countries - Eastern Europe and the USSR - which cannot be considered here because of absence of adequate information. Agreements can be concluded at any of the different stages from exploration through closing of a mine. While most contracts are negotiated at the time when a potentially viable ore body has been delineated and investigated sufficiently to anticipate a realistic time for commencement of production, other agreements start with "grass-roots" exploration, during operation of a mine, smelter or refinery or, exceptionally, after a temporary shutdown. While several major provisions are included in all types of agreements, others are covered in much more detail (or not at all) in some contracts reflecting the specific work programme of each project. While it is realized that subdivision and classification of complex contractual relations is necessarily arbitrary to a certain extent, such grouping is useful in practical terms, especially for the non-specialist. The following discussion, therefore, will start with a description of the major forms of contractual relation - concession, investment contract, joint venture, management agreement, service and production sharing contracts. Major issues covered in all, or almost all, agreements will then be dealt with. These include stages of development, corporate structure and control, fiscal arrangements, infrastructure development and environmental law, and dispute settlement and renegotiation. FORMS OF CONTRACT RELATIONS There has been marked change in the type of agreement entered into during the 1960s (and before) and the early 1970s and the period thereafter. While straight "concessions" - granting of exclusive rights to foreign investors over a certain deposit or areas with little restriction or well-defined obligations - were the rule during the first half of this century, more complex agreements have evolved since. Some of these cover every conceivable aspect, foreseen or only possible, and define rights and obligations of all partners to the last detail. Over the years, agreements have without doubt become more beneficial for the developing host countries, in part as a result of well-publicized nationalizations, as for example in Chile, and in part due to changed attitudes in all countries

Jan 1, 1985

By James A. Barr

Phosphate rock is a natural rock containing one or more phosphate minerals usually calcium phosphate, of sufficient purity and quantity to permit its use, either directly or after beneficiation in the manufacture of commercial products.1 The principal minerals in phosphate rock have the apatite structure which may be represented by the type formula: Ca10(X2) (PO4)6 where X represents the hydroxyl group (OH), chlorine or fluorine, either singly or collectively. The calcium may be partly replaced by sodium, magnesium, and other positive ions such as manganese, strontium, lead, uranium, cerium, yttrium and other rare earths. The PO4 radical may be partly replaced by small quantities of UO4, AsO4, SiO4, CO3, SO4, or Vo4. A typical commercial rock is usually a calcium phosphate containing 3 to 4 pct fluorine, the major impurities being limonite or other iron oxides, clay, aluminum phosphates and silica as quartz sand. A little vanadium is present in most of the domestic rock deposits (except the Tennessee Brown Rock), according to Jacob, Hill, Marshall and Reynolds! A little uranium occurs in the Florida leached zone, as will be brought out later. The chemical analyses are reported as P205, or tricalcium phosphate Ca3(PO4)2, the latter often designated by the trade name BPL (bone phosphate of lime). Commercial analyses usually report iron and alumina as oxides, lime as CaO and silica or insoluble. Colony3 examined many samples of apatite, staffelite, dahlite and American phosphorites and concluded that all have identical X-ray diffraction patterns. The phosphates in the phosphate rock have very minute crystalline structures. The mineral apatite Ca3(F.Cl) (PO4) 3 is the principal primary source of the element phosphorus, and occurs widely distributed in igneous rocks but rarely in a minable mass. Only about 12 pct of the world production of phosphate rock comes from primary apatites; the remainder is derived from secondary phosphorites. These phosphorites have been formed by the alteration of sediments by solutions containing phosphoric acid. Such solutions have come from the weathering or leaching of igneous rock containing apatite, bone deposits of prehistoric animals, marine life or guano deposits. These phosphorites are mostly alterations of phosphatic limestones. The sedimentary phosphate deposits are of marine origin and may have been enriched by subsequent solution of the more soluble calcium carbonate by waters containing carbon dioxide, by physical concentration by wave action, and by redeposition of the dissolved phosphate ions. Uses of Phosphate Phosphorus is the spark of life and is the structure builder and one of the main elements of plant food (fertilizer). Without phosphorus, life cannot exist. A "complete" plant food[t] in addition to phosphorus compounds contains potash, which acts as a catalyst to convert nutrients to useful forms, nitrogen to supply the growth element and many minor elements. The cycle of supply of phosphorus is from the apatite to solution and soil, absorption of plant life, decay and return to the soil or by animal life feeding on the plants. With insufficient supply of phosphorus in vegetation, life is not prolific. If crops are removed from

Jan 1, 1960

By John W. Gabelman

Uranium exploration technology historically has followed the economic cycle of demand, exploration spurt, and trailing supply; but with a greater lag. Greatest progress was made during the wane of demand as geological investigation caught up with the flood of new discoveries made during relatively short periods of peak demand. Updating brought technology to a new level based on the deposits which were discovered and not on the total range of deposit types which might exist. The technology was seldom able to predict new deposit types or new districts, which have consistently been surprises. Yet each new cycle of increased demand was at a new higher level, occasioned by a new use, which required the discovery of previously unrecognized larger types of deposits. Hindsight shows that data sufficient to have predicted most discoveries were available. The predicted growth of uranium demand far in excess of estimated resources is an incentive to examine current technology for data or promising techniques that might foster discovery by technical prediction rather than by systematic drilling. The world could well be reexamined systematically with new geophysical techniques including gamma spectrometry, radon emanometry, and magnetometry. Known occurrences could well be reevaluated in the light of new data on mineralization process and supergene leaching. Less-leachable extrinsic elements associated with uranium might he sought as clues to unleached uranium at depth. Uranium is increasingly being noted in environments containing coal and petroleum which might become targets. High-temperature replacement disseminations are increasingly reported and particularly attractive as exemplified by the Rossing district. The number of formations containing uranium occurrences is growing so that new, not necessarily fluvial, formations might be productive. Enough drilling has been done to indicate that uranium is selectively distributed regionally under some control yet to be determined. Exploration should address those environments and areas where uranium could occur rather than only those where it is already known.

Jan 1, 1976

By P. Shahinian, M. R. Achter

In a comparison of the creep -rupture properties of nickel in air arid in vacuum there is a reversal in relative strengths with variations in stress. At low stresses the properties are better in air while at high stresses they are better in vacuum. In the early stages of creep in a high stress test the specimen in air nzay have the lower creep rate but the one in vacuum is creeping at a lower rate in the later stages. A mechanism, involving two competing processes in terms of oxidation strengthening and weakening by surface-energy reduction, is proposed to explain these reversals. It had generally been assumed that, relative to their properties in air, the high-temperature strengths of metals would be increased in an inert atmosphere as a result of the elimination of the deteriorating effects of oxidation. However, several recent investigations have shown that the creep strength may be greater in air than in nonoxidizing gases. Pickus and Parker1 found that the creep rate of nickel was lower in air than in hydrogen or nitrogen. Internal oxidation was mentioned by Shepard and Schalliol as a possible cause for the longer creep life of Hastelloy C in air than in vacuum or helium. Sweetland and Parker, who observed lower creep rates for aluminum and copper in air than in helium, discuss the possible applicability of the dislocation-barrier mechanism to explain their results. Surface oxide layers may interfere with the escape of dislocations through the surface or with their generation there. In addition to showing the strengthening in air of low-alloy and stainless steel, and nickel and cobalt-base alloys, shahinian4 presented notch-effect data which indicate the role of stress concentrations; alloys of relatively low ductility were more sensitive to atmosphere strengthening when notched specimens were used. Although Bleakney's copper wires had a lower reduction of area in air than in vacuum, it is difficult to interpret his results in terms of strength changes since the stresses employed were not measured. In contrast to these data showing the strengthening in air, a number of investigations, most at relatively low temperatures, have demonstrated that the environment may cause a decrease in strength. These results are generally explained in terms of the effect of environment on surface energy. In a review of the subject, Benedicks and Harden use the concept of atomic bonding to explain how the adsorption of impurities would decrease the energy of a clean surface. A decrease in surface energy would facilitate the propagation of cracks or extension of the surface. Use of this mechanism is made by sato7 to explain the weakening of steel specimens bent in various liquids, by Potek and Shcheglakovs for the reduction of fracture strength of steel in molten metal, and by Benedicks and Harden for the reduction of strength of a variety of materials in a number of liquids. A similar explanation might be used for the results of Forestier and Clauss. The fracture stress of fine wires pulled in a variety of gases, including air, is lower than in vacuum. They attributed their results to the "tendency" for the gases to condense on the metal surface. That the strength of metals is affected by the type of gas in which the test is conducted has been demonstrated convincingly; the mechanism of the effect, however, is still uncertain. This investigation represents one in a series to explore the influence of variations in alloy composition and test conditions on the atmosphere effect in the expectation that the results would afford an insight into the processes taking place. To determine the effect of specimen composition, the present investigation was conducted

Jan 1, 1960

By Frederic Benard

The electrolytic copper refinery at Copper Cliff, Ont., is operated by the Ontario Refining Co., Ltd. The associated companies behind the enterprise are the International Nickel Co. of Canada, Ltd.; The American Metal Co.; The Consolidated Mining & Smelting Co. of Canada, Ltd.; and Ventures, Ltd. The plant was the outgrowth of the rapid development of copper resources in the nickel-copper ores of the Frood and other great mines in the Sudbury district, and of the desire to have all primary production units grouped together as closely as possible. The refinery is near the intersection of the Sault Ste. Marie to Sudbury highway and the Canadian Pacific Railway. It is about one mile south of The International Nickel Company's smelter at Copper Cliff. The standard-gage track systems of the refinery and of the smelter are connected by a standard-gage timber railroad trestle that crosses the railway and the highway by means of steel girder spans. The Canadian National Railway has access to the plant by means of this trestle and the nickel company's tracks, so that the refinery has connections with both the Canadian Pacific and the Canadian National railways, as well as a direct connection with The International Nickel Company's smelter, from which the bulk of the copper to be refined is hauled by the latter's electric locomotives. Buildings The refinery (Fig. 1) covers approximately 60 acres, enclosed by an unscalable chain-link fence. The main buildings have a content of 23,000,000 cu. ft., with a total roof area of approximately 600,000 sq. ft. and near them are the substation, cooling pond and main standard-gage track system (Fig. 2). A ladder track for car storage extends 1200 ft. south of the coal-pulverizer tracks and the scale house is on this spur. The intake and pumphouse for fresh water supply are at Kelly Lake, about 3000 ft. south of the plant. Owing to the severity of the winters, when temperatures of from 20" to 40' below zero are to be expected, the building of this refinery involved a number of problems in insulation, layout, ventilation, etc., which were

Jan 1, 1934

By P. F. Gnirk, J. B. Cheatham

The basic objective of this paper is to present a review of the state of knowledge concerning the fundamental mechanics of rock/bit-tooth interaction under downhole conditions. Of particular concern is the contributing significance of the various variables associated with the generation of rock chips by a single penetrating bit-tooth. The variables to be considered are fluid pressures which simulate borehole conditions, the mechanical properties of the rock, the shape and angle of attack of a bit-tooth, and the rate of load application on a bit-tooth. In addition, consideration is given to multiple bit-tooth penetration insofar as the effects of distance from and geometrical shape of adjacent penetration craters are concerned. Both experimental results and idealized theoretical models for single bit-tooth penetration are presented. Finally, the applicability of plasticity theory to drilling phenomena at depth, results of recent drag-bit studies, and several general theories of roller-bit drilling are briefly discussed. FUNDAMENTALS OF ROCK/BIT-TOOTH INTERACTION Drilling efficiency at depth in terms of penetration rate depends largely upon three essentially interdependent factors: 1) the bit, insofar as the mechanical motion, shape, and configuration of the bit-teeth are concerned; 2) the rock, as regards its mechanical behavior, or response to the penetrating action of the bit-teeth, when subjected to a state of stress induced by mud column, interstitial pore, and overburden pressure (and at great depths to high temperature) ; and

Jan 1, 1967

By S. L. Payne, J. P. Morris, R. L. Kipp, G. R. Zellars

The activities of iron and nickel in liquid Fe-Ni alloys were determined by measuring the vapor pressures of iron and nickel above the alloys and comparing with the vapor pressures of the pure metals. Nickel was found to deviate negatively from Raoult's law over the entire composition range. Iron behaves ideally down to 0.7 mole fraction but shows negative deviations at lower concentrations. At 1600°C the activity coefficients at infinite dilution are 0.40 for iron and 0.66 for nickel. 1 HE formulation of the conditions of chemical equilibrium between liquid metals and gases or slags is an important application of thermodynamics to pro- cess metallurgy. Usually the metal and slag phases are solutions of several components; and for accurate calculations, it is often necessary to use the activities of the components in place of their concentrations. Data concerning activities, however, are quite meager. The evaluation of the activities of iron and nickel, presented in this paper, is part of a project to determine activities in iron alloys at elevated temperatures.

Jan 1, 1960

By F. H. Wilson, R. M. Brick

WITH the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45° to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections. The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the earing behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass. EARING BEHAVIOR OF BRASS Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (113)[112]. This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;* Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photograms for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By Oliver Bowles

WHILE vast quantities of limestone and dolomite. are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little attention compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone' for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux "that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate discussion of metallurgical limestone problems.

Jan 1, 1928

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. TEMPERATURES AND UNDERGROUND WATERS Surface Temperatures.-The average surface dry-bulb temperature at Superior is 72.4º; wet-bulb, 57.4º; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the down- cast shafts; however, the variation between winter and summer causes a difference of only 2º to 3º in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.-Rock temperatures on the deeper levels of the mine are as follows: [ ] There appears to be no difference in rock temperature for any particular horizon of the various formations or in the vein. Water encountered is always the same temperature as the rock from which it flows, and for this reason it is thought that the water is heated by the rock; not the rock by the water. The country rock apparently has been heated by the various intrusions, perhaps the vein itself, and has not yet had time to cool off. The geothermal gradient (Fig. 2) as indicated by the rock temperatures given above is 1 ½ º per 100 feet. Underground Waters.-The underground water varies from 350 to 565 gal. per min., depending on the rainfall. The limestone and other

Jan 1, 1938

By W. T. Read, W. Shockley

THE subject of this chapter is the application of the dislocation theory to two problems of physical metallurgy where the theory has been able to give definite predictions that subsequently have been verified by experimental observations. Much of the history of dislocation theory has consisted of the explanation of already established results on the basis of ad hoc assumptions. Scattered bits of fundamental theory were formulated as needed-in particular explanations. The result had the appearance of a hodgepodge of ingenious ideas and exciting but possibly artificial speculations. The review article by Koehler and Seitz in this volume gives an excellent picture of the breadth, diversity, and flexibility that have made dislocation theory attractive to speculative theorists, although occasionally bewildering to others. Since 1950, there have been two developments, which have helped to establish dislocation theory, on the one hand, as a systematic coherent body of theory and, on the other, as a means of making predictions that can be tested experimentally and thereby guide experiment into more fruitful channels. The first and easier of these developments has been the systematic derivation of the classes and properties of dislocations from fundamental crystallographic concepts. An example of one phase of this development is the rigorous treatment of

Jan 1, 1954

By G. Sachs, E. P. Klier, W. Beck

HYDROGEN embrittlement of steels has recently attracted much attention because it is asso- ciated with a variety of failures, especially those of aircraft structural components.' For instance, one of the undesirable properties of the ultra-high strength steels used for landing gears is their pronounced susceptibility to hydrogen embrittlement during plating. The presence of hydrogen in these steels becomes particularly apparent through delayed or sustained load failures of parts which have been subjected to low loads for an extended time. A number of variables are involved in causing a reduction of strength and ductility through hydrogen

Jan 1, 1957

By Thomas A. Read

THE internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of l00 when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose-that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals will be presented. EXPERIMENTAL PROCEDURE The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrement A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were .made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders ¼ in. in diameter and 1 ½ to 2 ½ in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is ¼ in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941