Search Documents

By M. C. Udy, C. H. Lorig

THROUGH the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the general effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. LITERATURE Two general factors should he considered in a study of reduction of iron oxide: (1) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe3O4-FeO-H2-H2O, Fe304-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnas1 published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at one temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1942

By John V. Beall

When the mineral seekers came, they brought romance, excitement and, too often, transitory riches. It has been so for uncounted centuries. While the rich ore lasted, living was high and money flowed-mostly out of town. The whole creation was like a circus. The headframe went up like the center pole of the big top. The reduction works was an ingenious affair; an opportunity for self-expression by the mining engineer on the job. When the high grade gave out or the bottom dropped out of the market, the whole show folded. Machinery was scavenged for the next location. About all that was left were the raw footings, like giantsteps on the hillside; and the headframe above the silent diggings. Mostly, the people went away too. Arizona Territory was like that at the turn of the century. It can still happen. But, in copper, the age-old pattern has been disrupted. From Mineral Park in the northwest to Chino in the east and Cananea in the South, a growing number of companies have emerged-large, stable, productive. Southwest copper is truly a mighty industry, accounting for one fifth of world new copper production. In this period of scientific development, changes are fast, often dramatic. But even mining engineers, or possibly more so because they have an intimate knowledge of the industry, fail to appreciate the evolutionary changes that have shaped Southwest copper into what it is today.

Jan 10, 1965

By Arthur A. Center

HIGH GRADE zinc stocks were reported short early in 1943, but not Prime Western. Maximum production of High Grade was expected to be reached before the middle of the year, and demands of new brass mills were to take all of the increase. In February three premiums (A, B, C) of 2 3/4c. per lb. of zinc in ore were announced to encourage production from high-cost mines, the number of premiums being in proportion to estimates of ore-production costs.

Jan 1, 1944

By A. Jowett

An attempt is made to explain differences in the size-by-size response to flotation of some sulphide minerals. Physical factors involved in particle-bubble collision and adhesion, and also in possible subsequent disruption of aggregates, are considered especially in relation to flotation of the coarser sizes. Emphasis is on practical observations and their significance, with an essentially qualitative theoretical treatment designed to form hypotheses for further experiments. In particular, the theoretical effects of contact angle and induction time are examined. An argument is developed which suggests a rapid increase in induction time as particle size increases, except for particles small enough to be moving under laminar flow conditions. This can adequately explain poor recoveries of coarse particles in flotation without a need to assume disruption of particle-bubble aggregates in turbulent zones in a flotation cell. Flotation recovery is shown to be very sensitive to small changes in induction time. Consideration of the physics of disruption of particle-bubble aggregates leads to the conclusion that this mechanism does not adequately explain differences in flotation recovery of coarser sizes of some sulphide minerals. For example, to explain differences in recovery of coarse galena and chalcopyrite by this mechanism would necessitate accepting that conditioning with ethyl xanthate which would promote a 60º contact angle at a galena surface would promote only an 11º angle at a chalcopyrite surface. Small differences in induction time arising from differences in surface chemical characteristics of the various minerals offer a more satisfactory explanation of differences in recovery of coarser sizes.

Jan 1, 1980

By J. S. Crump, H. L. Stone

Laboratory studies have indicated that displacement of oil from a reservoir by means of a condensing gas drive results in extremely high oil recovery, approaching 100 per cent under the most favorable circumstances. A condensing gas drive is defined as a gas drive in which the gas utilized is appreciably soluble in the oil it is displacing. The laboratory studies consisted of a number of gas drive displacement experiments, all using a horizontal, sand-packed, steel tube as the laboratory reservoir. The experimental results indicate that the more soluble a gas is in the oil to he displaced, the more efficient that gar is as a displacing fluid. Experiments were conducted utilizing both a light, volatile crude and a heavy, asphalt crude as the in-place oil. In both cases, oil recovery was appreciably enhanced by solubility of the displacing gas. It is believed that the use of condensing gas drives would result in increased oil recovery from many reservoirs during either primary or secondary phases of production. INTRODUCTION Since the early days of the oil industry there has been an increasing awareness of the problems of oil recovery. During the last few decades particularly a growing recognition of the problems has led to widespread attempts on the part of the industry to increase oil recovery by improved technology. One method which has been used to increase recovery is the maintenance of reservoir pressure by injection of gas. Part of the beneficial effect resulting from this gas injection was to prevent evolution of the gas dissolved in the reservoir oil, since such evolution would cause the oil to shrink and become more viscous, thereby adversely affecting oil recovery. In most instances, the gas injected was predomillantly methane, and so the possibility of oil recovery by retrograde vaporization existed. Laboratory investigations of displacement of reservoir oils by methane, carried out at high pressure, have indicated that considerable additional recovery of light oils could be effected by vaporization, but only at the cost of a severe volumetric shrinkage of the residual oil which would cause a decrease in relative permeability to oil in the reservoir. Consequently, recovery of oil by physical displacement would be impaired. The study suggested, therefore, that recovery of oil might be enhanced by injecting into the reservoir a gas known to be appreciably soluble in the oil at reservoir conditions. Swelling of the oil due to solution of gas should result and yield a consequent increase in the relative permeability to oil. The work described in the following sections was, therefore, undertaken to investigate the possibility of increased recovery by this mechanism. Research similar to that reported in this paper has been conducted by The Atlantic Refining Co.1,2,3 In these studies, Whorton, et al, and Slobod, et al, used methane-rich gas to displace oil from model reservoirs. Solubility of the gas was achieved by keeping the reservoir pressure greater than the saturation pressure of the original oil, and the degree of this solubility was varied by operating at different reservoir pressures. Thus the Atlantic project was primarily a study of the effect of reservoir pressure upon oil recovery by gas drive. The objective of the work reported in this paper was to study the effect of gas composition upon oil recovery while holding the reservoir pressure constant. DESCRIPTION OF EXPERIMENTS The discussion of the preceding section suggests that

Jan 1, 1957

By J. B. Wagstaff

The raceway in front of the tuyere of the blast furnace has been studied quantitatively and a correlation obtained for the penetrastudiedtion of the blast. Some evidence is presented for the height and width of the raceway which suggests that all the raceways of a ffurnace overlap. The size of the coke in this zone has been measfurnaceoverlap.ured photographically during normal operation and results are given for the various areas. IN an earlier paper,' it was shown that a raceway exists opposite each tuyere of a blast furnace. This raceway is formed by the jet effect of the air emerging from the tuyere and consists essentially of a turbulence in which coke particles are recir-culated at high speed. Its presence was deduced originally from observations on movies taken with a high-speed camera through the tuyeres of various furnaces and was confirmed by experiments made on a model. In the model described,' this raceway was shown as operating in a vertical plane only, although there was a suggestion in the motion-picture film exhibited at that time that the raceway was three dimensional, unless artificially restricted. There was also some doubt then about the factors influencing its size. This paper describes the next steps in the investigation. Since the size of the raceway is obviously of importance in the operation of the furnace, it seemed worth while to study the subject more carefully. It is probably in this region that about half the coke in the furnace is consumed, so that the movement of the stock column may well be controlled by raceway behavior. Furthermore, there is some evidence to suggest that the coke is packed densely in the center of the furnace to form the "dead man" and more loosely above the raceway. It is therefore probable that the bulk of the gases passing up the stack flow from the top surface of this raceway. Clearly then, a knowledge of this critical zone is of interest to the blast furnace operator, and the first half of this report is devoted to a quantitative discussion of the subject. A further topic of interest among operators is the degree of breakdown of coke in the furnace, with which is inseparably linked the importance of a strong coke. Indeed, the whole question of the optimum size and type of coke may be as dependent on the condition of the coke in the bottom of the blast furnace as at the top. Attempts have been made from time to time to obtain samples of coke from the tuyeres and other furnace openings but they all suffer from the fact that the coke is filled to a varying degree with metal and slag and is probably broken up by the very act of taking the sample. It has proved difficult to make any reliable studies of coke size by these methods. However, it did seem possible to use the highspeed movies mentioned earlier1 to estimate the size of the coke. These movies provide an accurate record of individual coke particles so that, in theory at least, it should be possible to measure the size of the particles one by one and to obtain, for the first time, information on the coke being blown around the raceway under actual operating conditions while the furnace is performing normally. Such a study has been made and is discussed in the second half of this paper. The results obtained enabled the blast furnace data to be correlated with the model results given in the first half. Raceway Size In order to make a quantitative study of the size of the raceway it was necessary to devise some apparatus of laboratory scale, which could be handled quickly and easily. This focused attention on models, which in turn means that the laws of similarity governing this particular process must be ascertained. Method of Procedure: Since the work was to be carried out on a smaller scale than the blast furnace, the linear dimensions of the model became unimportant provided that the scale was known; it is only important to insure that the container does not affect the raceway being observed. The studies therefore were carried out in a glass-sided box, 11 in. high x 7 in. wide x 3 in. deep, using air jets ranging

Jan 1, 1954

By F. D. George, M. J. Salkind

Al3Ni whisker-reinforced aluminum was found to exhibit good Charpy impact toughness and little notch sensitivity even though its room-temperature tensile elongation parallel to the whiskers is only 2 pct. This impact behavior was maintained d liquid nitrogen temperature (-196"C). It is postulated that this behavior is due primarily to the presence of the continuous aluminum matrix which provides sufficient 10calized ductility in the vicinity of the crack tip to absorb considerable energy from the advancing crack. The impact behavior of Al-Alni was found to be quite anisotropic. Of six orientations studied, the transverse orientation having the notch normal to the whisker axis was found to exhibit the lowest impact energy, whereas the transverse orientation having the notch parallel to the whisker axis was found to exhibit the highest impact energy. A significant differnce was noted between the impact behavior of material containing needlelike whiskers and that containing bladelike whiskers. Only two of the six orientations studied exhibited complete fracture for the material containing needlelike whiskers. On the other had, most of the specimens containing bladelike whiskers exhibited complete fracture. It was postulated that the bladelike whiskers block transverse flow, thus reducing the amount of plastic deformation ahead of the crack tip. One of the more significant advantages of composite materials is the prospect of combining high strength with toughness. In general, toughness is associated with materials which exhibit considerable ductility and can deform plastically in the presence of a stress concentration. Very strong materials which resist plastic deformation generally exhibit low toughness. At first glance, then, it would appear as though strength and toughness are mutually incompatible so that useful engineering materials would have to be a compromise between the two. One approach to the problem of combining the high intrinsic strength of ceramics with the toughness of metals was to mix them together to form a cermet. Unfortunately, the toughness of cermets was found to be rather disappointing. Whisker reinforcement of metals, however, appears to be a more promising approach. It has been demonstrated that whisker-reinforced metals produced by unidirectional solidification exhibit enhanced strength due to the presence of high strength nonmetallic whiskers. The total strain capacity of these composites in the direction of fiber alignment is limited to that of the fibers, the matrix being unable to carry the load once the fibers have failed. A characteristic, then, of whisker composites is low ductility in the direction of whisker alignment, on the order of a few percent elongation. This low elongation, which is usually associated with brittle behavior, should not be taken as an indication of low toughness. Such a material can exhibit significant ductility in directions other than parallel to the fibers7 and can therefore possess significant intrinsic toughness. Toughness in a fiber-reinforced metal is derived from several mechanisms. The first is due to the toughness of the matrix itself. A continuous ductile metal matrix can act as an effective crack arrest medium by undergoing localized plastic deformation. Cracks initiated from the surface of the composite or from a brittle fiber failure must travel through the matrix before reaching another brittle phase particle. A second crack arrest mechanism peculiar to fiber composites is due to the fact that, as a crack travels through the matrix and approaches a fiber, the plastic deformation ahead of the crack tip will result in loading of the fiber. This causes the matrix shear strength in the plastic zone to be apparently higher, thus extracting more energy from the crack and diverting the crack at an angle to the original direction of propagation. A third crack arrest mechanism occurs in fiber composites which exhibit a weak bond between fiber and matrix. The idea was proposed by Cook and Gordons that if a crack propagating transversely in a fiber composite were made to turn and run along the fibers by decohesion of the fiber-matrix bond, then toughness would be imparted by the blunting of the crack tip and the creation of new surfaces. The last mechanism, interfacial decohesion, is commonly noted in naturally occurring fiber composites such as wood, bone, and bamboo, and has been observed in man-made composites such as glass fiber-reinforced resins,g silica fiber-reinforced aluminum," laminated steel," and tungsten and silica fiber-reinforced electroplated copper.'' The first mechanism, crack arrest by plastic deformation in the matrix, has been noted in tungsten wire reinforced cast copper." The purpose of this investigation was to quantitatively assess the toughness of a whisker-reinforced metal as a function of orientation. Previous investigation considered only cracks propagating nominally perpendicular to the reinforcement. In this investigation, crack propagation in three mutually perpendicular directions as well as three intermediate orientations was investigated. The system chosen for study was the unidirectionally solidified A1-A13Ni eu-tectic alloy which has a microstructure consisting of 10 pct by volume of A13Ni whiskers in a matrix of aluminum This material exhibits two different kinds of whisker morphology, depending upon the rate at which it is solidified.' At low rates of solidification (less than 2 cm per hr) the whiskers are bladelike, whereas at higher rates of solidification they are

Jan 1, 1969

By L. D. Fetterolf

The New Jersey Zinc Zompany operates at Depue, Illinois, an integrated zinc smelting plant using tie vertical retort reduction process. The overall operation comprises green concentrate roasting, sintering, vertical retort smelting and metal refining. In the roasting operation, the fine concentrate is pelletized, the dried pellets fluidized and autogenously roasted with air in a “fluid column” with minimal formation of dust requiring recirculation. The roasted pellets and any associated roaster dust are agglomerated in a rotating drum and laid down, in combination with coal for fuel, on a Dwight-Lloyd sintering machine which converts to a semi-fused mass - a physical state more suitable for vertical retort smelting. The smeltins plant of 27 vertical retorts rated at 8 T zinc each per day on average requires the following major processing steps - mix preparation and briquettine, briquet coking, vertical retort reduction, vapor condensation and slab casting of metal. A portion of zinc production is converted to 99.99+ percent purity by boiling and fractional distillation in columns consisting of externally heated, superimposed trays of high-conductivity refractory.

Jan 1, 1970

By R. Steven Maxwell, Ulrich Petersen

Most minerals have experienced a slow hut perceptible decline in their annual primary production growth over the past hundred years. This decline is due to a combination of factors: (1) increased recycling; (2) exhaustion of the more accessible or higher grade ores; (3) partial substitution; (4) the more efficient use of materials; (5) progressive saturation of markets as living standards rise. Therefore, future demand for new mineral resources will probably be lower than anticipated. As the world population stabilizes, this slowdown in production growth will become even more pronounced.

Jan 1, 1979

PRECEDING chapters on thermochemistry, and the reactions in and between metal and slag phases in the bath of the furnace tend to emphasize the equilibrium or "static" conditions in the furnace and process, such as the total amounts of heat from fuel combustion or from certain bath reactions, the concentration relationships between slag and metal at the steady state for certain reactions, and the like. Such data are obtained essentially by means of the logic of thermo- dynamics, which helps to determine the energy change between initial and final states in a process as well as to define its equilibrium or steady-state condition, but which is not concerned with the rate of change in the process or with the mechanisms or path followed between initial and final states. These questions of just "how it works" and "how fast" belong to the kinetic aspect of any process; their answers are helpful in speeding up or slowing down and thus controlling intelligently its operation, and also to understand certain natural limitations which are especially important in many high-temperature processes. The kinetic aspects of interest here comprise mainly (1) the flow of gases through the furnace system, (2) the flow of heat in the system, and (3) the mechanisms and rate factors in the various chemical reactions. A really adequate discussion of the first two subjects would require at least three or four times the space available here; it has been tried, therefore, in this and the next chapter to outline but a few fundamentals necessary to an intelligent approach and to indicate some of the conditions of heat and gas flow more or less peculiar to the open hearth, since several good general discussions on these subjects may be found in the literature.(1) For the designer of open-hearth furnaces, the principles of gas flow are of paramount importance.(2,3,4,5) They are also important to the operation of the process, however, at least to the extent of a general qualitative picture of the movement of gases in the system, which is all that is attempted here.

Jan 1, 1944

By F. Weinberg, E. H. McLaren

Dilute binary alloys have been solidified under controlled thermal conditions, and solute distributions, temperatures during freezing and melting, and the position and morphology of the solid-liquid interfaces have been examined. Binary Zn, Sn, and Pb based alloys were investigated with solute additions of AgU°, AU°, Sb'24, TlZo4, snH3, and Zns5. Approximately 150 cc of metal was used in each ingot. Appreciable solute segregation occurred in most of the ingots, depending on the solute concentrations, distribution coefficients. and freezing conditions of the alloys. Measurements were made of the general solute distribution by sectioning layers of material from the ingot circumference and counting the activity of each layer. Local segregation was detected by autoradiographic techniques. Freezing and melting curves for the same alloys were obtained by precision resistance thermometry. These curves are related to the corresponding measured solute distribution curves and those calculated from theoretical expressions. The position and morphology of solid-liquid interfaces during freezing were determined by both decanting and quenching techniques. The results indicate the manner in which freezing and remelting occurred under the conditions investigated. If an isomorphous dilute binary alloy is solidified or melted under equilibrium conditions, the concentration of solute in both solid and liquid would be uniform at all stages in the freezing process. The solute concentrations during freezing could be determined from the phase diagram of the alloy, and the freezing curves would have an alloy slope defined by the solidus and liquidus points. In practice, however, solidification under equilibrium conditions rarely, if ever, occurs, primarily because of low rates of diffusion in the solid and incomplete mixing in the liquid. As a result, the solute distribution and the shape of the freezing and melting curves obtained in a given system depends on a number of factors. These include, in addition to the extent of diffusion and mixing, the initial solute distribution and concentration, the distribution coefficient, the rate of freezing or melting, supercooling of the liquid, the morphology of the solid-liquid interface, and the effect of annealing. The purpose of the present investigation was to determine, experimentally, actual solute distributions and thermal curves for a series of dilute binary alloys, using tracer techniques to determine the solute distributions and precision resistance thermometry for the temperature measurements. In addition, observations were made of the positions and morphologies of the solid-liquid interfaces during freezing and remelting. The distribution of solute in a dilute alloy, assuming complete mixing in the liquid, and negligible diffusion in the solid, is given by1 where Co is the mean solute concentration of the alloy, C, is the solute concentration in the solidg is the fraction of the ingot solidified, and ko is the equilibrium solute distribution coefficient (assumed to be independent of concentration for dilute alloys). For the case of partial mixing, ko can be replaced by an effective distribution coefficient k. If solute transport in the liquid is assumed to be entirely due to diffusion, with negligible diffusion in the solid, then the solute distribution in the solid is given by Tiller et a1.' as where R is the rate of advance of the solid-liquid interface, D is the solute diffusion coefficient in the liquid, and x is the position of the interface from the start of freezing. The temperature at the interface TI is related to the solute concentration of the solid at the interface C, by the expression where Tm is the freezing temperature of the pure solvent and ml is the slope of the liquidus for the binary alloy being considered. Accordingly, by relating TL to the actual temperatures measured in the present experiments, solute distributions can be deduced from the temperature measurements. Using the above expressions, the measured solute distribution of a given alloy may be compared to the theoretical distributions, as well as to the distribution calculated from the observed freezing curve. EXPERIMENTAL The solvent materials used in making up the binary alloys were C. P. New Jersey zinc (99.999 pct), Vulcan Extra Pure Tin (99.999 pet), and Tadanac lead (99.998 pct). The solute elements were of 99.99 pct purity or better, and were activated in the

Jan 1, 1963

By Robert L. Braun, Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides, chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 100° to 150°C. The rate of dissolution of chalcopyrite exposed to oxygen-saturated solutions becomes so rapid under these conditions that the rate of copper extraction becomes limited by the accessibility of chalcopyrite to the solutions. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, and size of ore particles. It is concluded that the high pressure and high temperature obtainable in a large ore mass broken by nuclear explosives promise the rapid and economic recovery of minerals not considered soluble by conventional in-situ leaching methods. The method should be broadly applicable to the kinds of deep deposits that must be depended on for future production and with minimum disruption of the environment.

Jan 1, 1974

By George W. Bain

Some problems concomitant with commercial exploitalion of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service department wants defects rectified and the cause determined to avoid recurrence The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character. Geological Problems The geological problems deal almost exclusively with the size of blocks. Size across the deposit is limited by thickness of individual beds. and along the strike by the space between crosscutting joints. Frequently the vertical depth of a block is reduced by exfoliation shells arising from spontaneous expansion. All these factors require consideration in developing a deposit to fill an order. Thickening of Marble Beds The limestone beds that became the marble deposits of the northern Appalachians and of the Yule locality in Colorado were seldom homo-

Jan 1, 1941

By George W. Bain

Some problems concomitant with commercial exploitalion of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service department wants defects rectified and the cause determined to avoid recurrence The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character. Geological Problems The geological problems deal almost exclusively with the size of blocks. Size across the deposit is limited by thickness of individual beds. and along the strike by the space between crosscutting joints. Frequently the vertical depth of a block is reduced by exfoliation shells arising from spontaneous expansion. All these factors require consideration in developing a deposit to fill an order. Thickening of Marble Beds The limestone beds that became the marble deposits of the northern Appalachians and of the Yule locality in Colorado were seldom homo-

Jan 1, 1941

By H. Conrad, V. V. Damiano, G. J. London

A method is described for producing single crystals of high-purity beryllium, Be-4.37pct Cu, and Be-5.24 pct Ni. These crystals were prepared for testing in compression parallel to the [0001] by orienting and lapping to within ±3' of arc of the (0001). Microstrain testing apparatus is described along with c axis compression results for ingot purity beryllium, twelve-zone-pass material, and the above-mentioned alloys. Results show no measurable plasticity for the ingot purity material from -196" to 400°C, although some surface traces of (1122) slip was observed at 200°C and above. The twelve-zone-pass material shows substantial microstrain plasticity at 220°C with slip on (1122). Both alloys show significant plasticity at room temperature and above with slip also on (1122) planes. THE two slip systems which normally operate during the plastic deformation of beryllium in the vicinity of room temperature are:' basal slip (0001)(1120) and prism slip . Pyramidal slip with a vector inclined to the basal plane has been reported for elevated temperatures,'-a but occurs near room temperature only at very high stresses.~ A summary of the available data on the effect of temperature on the critical resolved shear stress for slip on these systems has been compiled by Conrad and Perlmutter.~ It has been postulated6'7 that one of the principal factors contributing to the brittleness of poly crystalline beryllium at temperatures below about 200°C is the difficulty of operating pyramidal slip with a vector inclined to the basal plane. Hence, detailed information on the operation of such a slip system is important to understanding the brittleness of beryllium. The operation of pyramidal slip with a vector inclined to the basal plane is best accomplished in beryllium by compressing single crystals in a direction parallel to the c axis. In such a test the resolved macroscopic shear strzss on the basal and prism planes is zero and (1012) twinning which is favored by tension along the c axis does not occur. Hence, in c axis compression of beryllium the normal deformation modes are inhibited and the operation of pyramidal slip with a vector inclined to the basal plane is favored. In the present investigation, c axis compression tests were performed on beryllium single crystal as a function of temperature (77" to 700°K), purity (commercial and twelve zone pass), and alloy content (4.37 wt pct Cu and 5.24 wt pct Ni). Presented here is a description of the test techniques employed and the gross mechanical behavior observed. A detailed analysis of the slip traces developed on the surfaces of the deformed specimens during these tests and the results of electron transmission studies of the deformed crystals are given in a separate paper.B PROCEDURE 1) Materials and Preparation. Single crystals about 1 in. diam were prepared of the following materials: commercial-purity beryllium, high-purity beryllium, and two beryllium alloys, one with 4.37 wt pct Cu and the other with 5.24 wt pct Ni. The commercial-purity single crystals were obtained by cutting specimens from large-grained ingot of Pechiney SR material, which is approximately 99.98 pct pure. The high-purity crystals were prepared by floating-zone refining (twelve passes) a rod (7 in. by 1 in, diam) of Pechiney SR grade cast and extruded beryllium. Although an absolute chemical analysis of the zone-refined material was not established, mass spectro-graphic analysis, emission spectrographic analysis, and y activation analysis indicated that it contained in atomic fractions about 5 to 10 ppm each of carbon and oxygen, 1 to 5 ppm each of nickel and iron, and about 1 to 2 ppm of copper, with the remaining residual impurities being less than 1 ppm. Further indication of the purity of this material is provided by the critical resolved shear stress for basal slip, which was approximately 300 psi. The starting material for the alloy single crystals was 1-in.-diam floating-zone-refined (six passes) rod of Pechiney SR grade beryllium. Two such rods were wrapped respectively with sufficient weight of wire of high-purity copper (99.999 pct) or nickel (99.999 pct) to yield a 5 wt pct alloy. A seventh floating-zone pass was then applied to each of the rods to accomplish the initial alloying and an eighth pass for homogenization. Analytical samples were taken from regions of the rod immediately adjacent to where the mechanical test specimens were cut; these indicated 4.37 wt pct Cu and 5.24 wt pct Ni. 2) Crystal Orientation. To avoid the occurrence of basal slip during c axis compression testing, it is necessary to load the crystals as nearly parallel to the c axis as possible. Preliminary c axis compression tests indicated that plastic flow and/or fracture occurred at stresses of the order of 300,000 psi; hence on the basis of a critical resolved shear stress for basal slip of 300 to 400 psi, the maximum crystal misorientation permitted is about 4 to 5' of arc. Since this accuracy cannot be obtained using the usual back-

Jan 1, 1969

During the past year the Committee on Coal and Coke has been collecting data concerning various phases of the bituminous industry about which considerable misinformation has been circulated even, in some cases, through the coal trade papers. The data here presented have been compiled by various members, from the most authentic sources available and, where possible, cover the period 1913-1924. They will enable comparisons to be made within the industry, and of this and other industries, and will explain some of the differences between conditions existing now and in the prewar period. Capacity and Over-development The capacity of bituminous mines is frequently stated at figures ranging between 800,000,000 to 1,400,000,000 tons per year. Table 1 shows statistics for the industry, mainly from U. S. Geological Survey sources but partly from U. S. Coal Commission reports. Column 3 gives the mine capacity with equipment and labor as of given date, as estimated from the data published by the U. S. Geological Survey. This is calculated for each State by obtaining the total man days worked as reported by the operators (multiplying average men employed by total days worked at each mine) and dividing this figure into the total production, getting the production per man day; this figure times number of men employed times 308 (a theoretical full working year) equals estimated full-time capacity. Two major objections are made to this method—one that the total number of men employed is used, instead of the number actually working, and the other that the number of days used only deducts Sundays and five holidays. The first objection is answered by the fact that the same number of men is used in estimating capacity as is used in actual production, and while this number is always from 12 to 20 per cent. more than are actually working, this condition exists at all times, although it is worse at times of maximum output. Few coal men will agree with the conclusion that the use of 308 days is correct, as it is practically impossible to keep any mine working full time at the same daily rate of production as when it is working part time, and the opinion is

Jan 1, 1927

Jan 1, 1887

By Dorsey A. Lyon, Robert M. Keeney

The electric furnace has always been found to be especially adapted to melting, refining, and finishing processes throughout its gradual acceptance by metallurgists as a practical apparatus for conducting metallurgical operations. In the steel industry, the electric furnace is firmly established in the manufacture of steel of the highest grade, equal to crucible steel. For the production of the cheaper grades of steel in large tonnage, the electric furnace gives a higher-grade product than the open-hearth or converter, but due to the high cost of power prevailing in steel centers, considered from the electric furnace standpoint, it is not economical to produce tonnage steel in the electric furnace. As a refining and finishing agent for open-hearth or Bessemer steel, the electric furnace has had some degree of success in thc production of tonnage steel. After a study of the use of the electric furnace in the steel industry, it appears that there may be a possibility of its use to advantage for the melting of cathode copper. In the case of copper the problem is not one of actual refining, because the copper if refined properly by the electrolytic method needs no further refining; it needs simply to be cast into a marketable shape. The name "refining" is applied to the present finishing process, because in the operation oxygen and other impurities arc removed, which the electrolytic copper absorbs in being melted in the reverberatory furnace. Considering that processes may be positive, negative, and neutral, the electrolytic method would be positive; reverberatory melting of cathode copper, negative; and electric furnace melting, neutral. The electrolytic method produces about as pure a copper as is possible, if operated properly and the anodes are not too impure. The final reverberatory melting of this cathode copper lowers the grade of the final product, due to the absorption of gases and impurities. The reverberatory melting of cathode copper is one of the weak parts

Jan 1, 1915

By B. R. Palmer, M. C. Fuerstenau

Oxide and silicates respond to flotation with a large number of anionic collectors. These include carboxylates (fatty acids), sulfonates, alkyl sulfates, and certain chelating agents. In contrast to sulfide mineral flotation, relatively long-chained collectors (generally longer than 10 carbons) are required to effect flotation of this group of minerals. The structural formulas of these various anionic collectors are presented in Table 1. Formulas and solubilities of various fatty acids are presented in Table 2. These solubilities are those of the dissolved and undissociated species of the acid, e.g. oleic acid, HOl(aq). Of the compounds listed, oleic acid and abietic acid, which IS a major constituent of talloel, are used most commonly in commercial applications. The usage of these two collectors is related to cost and effectiveness. In addition to their high molecular weights, oleic acid contains a double bond in its hydrocarbon chain, while abietic acid is comprised of aromatic rings containing double bonds. The presence of double bonds increases solubility significantly over that of saturated homologues. Stability of metal-collectors assumes a most significant role in these systems, and the solubility products of various metal carboxylates and sulfonates are listed in Tables 3, 4 and 5. In addition to these properties, strength of the acids of these various anionic collectors is also important. The carboxylic and hydroxamic acids are weak acids whereas sulfonic and alkyl sulfuric acids are strong acids. All of the carboxylic acids fall in the range of pK = 4.7 ± 0.5 ([2]); the pK of hydroxamic acid is around 9 ([3]); and the pK of sulfonic acid is about 1.5 ([4]).

Jan 1, 1976

By Joseph Singewald

AMONG the genetically interesting iron ores of the United States are those of the St. Francis Mountains near Ironton and Iron Mountain, Missouri. They are specular hematite in porphyry. The Iron Mountain and Shepherd Mountain deposits are generally spoken of as veins and those of Pilot Knob, Cedar Hill, and Russell Mountain as bedded deposits. Iron Mountain has produced nearly 4,000,000 tons of ore and Pilot Knob about 1,500,000 tons. The output of the other three localities has been insignificant. Pilot Knob is no longer worked as an iron mine, but the rock is now being crushed for use as road metal. Iron Mountain has continued as an active producer. In 1927, the property was acquired by the M. A. Hanna Co. and an extensive prospecting and exploration campaign was undertaken, so that the ultimate production of Iron Mountain will doubtless greatly exceed the figures mentioned.

Jan 1, 1929