Search Documents

By Herbert Haas

CHEAP power is essential to large-scale mining and metallurgical operations, particularly where fine grinding of large tonnages has to be resorted to, as is the case with an increasing number of. mines treating disseminated copper ores, or low-grade gold ores, in the grinding of which considerable power is consumed. A comparison of the cost of generating power with Diesel engines and steam turbines and a brief discussion of the different factors governing the profitable use of either type of prime mover may be timely in view of the importance of. a cheap supply of power to the mining industry, and the prominence that has lately been given to Diesel engines in America. As many of our most important mines and largest producers of metals are located in sections where neither cheap coal nor water power is available, and the price of oil fuel is increased by long hauls, the Diesel. engine will. become a prime mover of increasing importance. This applies particularly to the Southwestern States, where an ample supply of cold water for condensing purposes is unusual and local climatological conditions interfere in securing the high vacua essential to high turbine efficiency. About 12 times as much water will be required for condensing purposes with steam turbines under general conditions as is needed for jacket-cooling of two-stroke, cycle Diesel engine; four-stroke cycle Diesel engines require only one-twentieth of the cooling water. Another condition favoring the use of Diesel engines is the high load factor at which most mine power plants operate. The influence of load factor on the cost of generating power is shown in Tables 1 and 2 and in Fig. 1.

Jan 7, 1916

By Ian Wark

SODIUM sulfide is used extensively to increase the recovery of oxidized copper and lead minerals by flotation, particularly when using xanthates as collectors. It is generally assumed that the sodium sulfide converts a film of the oxidized mineral to the sulfide, and that the xanthate, while not a very effective collector for the oxidized minerals, is a good collector for the sulfide. On the other hand, Taggart and his collaborators' claim that unless sulfide minerals are oxidized they cannot adsorb xanthates and do not float. Gaudin2 states that amyl xanthate, used in conjunction with sodium sulfide, gives better results than ethyl xanthate. Rabone3 and Mayer-Schranz4 agree that excess of sulfide functions as a depressant. Owing to the greater solubilities of the oxidized minerals than of the sulfides, the consumption of sodium sulfide is greater than that of most other flotation reagents, up to 10 lb. per ton of ore being used in some plants. Luyken and Bierbrauer5 recommend a water washing to remove soluble heavy metal salts; by this means sulfide consumption may be reduced. It was desirable to determine the limits of the sulfide concentrations between which contact is possible at surfaces of anglesite and cerussite in xanthate solutions. Similar determinations were desirable for the sulfide minerals with which the oxidized minerals are usually associated, since conditions should be chosen, if possible, so that the two types of mineral will float together. Because of the formation, especially in acid solutions, of hydrogen sulfide and of the hydrosulfide ion (HS-), the permissible limits of sulfide addition are obviously dependent upon the pH value. Sphalerite responds to ethyl xanthate only in the presence of an activator; for example, copper sulfate. It was necessary, therefore, to determine whether sodium sulfide interferes with the activation of sphalerite by copper sulfate. The combined effect of sulfide and copper sulfate was determined also for galena, chalcopyrite and pyrite.

Jan 1, 1936

By H. M. Hobart

THIS paper deals principally with investigations undertaken by the Welding Research Sub-committee of the Welding Committee of the Emergency Fleet Corporation. The general object of the investigations has been to extend the use of welding in the construction of merchant ships and, specifically, to provide a definite basis for obtaining the best economy and efficiency in employing welding in place of riveting in the construction of the hulls of such ships. Composition of Ship-plate Steel The chemical composition of the steel employed in such hull construction varies with the thickness of the plates. Through the courtesy of Mr. H. Jasper Cox of Lloyd's Register of Shipping, the following information may be given concerning the kind of steel plate employed in American Shipyards in 1918 for the hull construction of merchant ships. Lloyd's requirements do not relate to the chemical composition. They require a tensile strength of 58,000 lb. per square inch (40.75 kg. per sq. mm.) for their lower limit and 72,000 lb. per square inch (50.59 kg. per sq. mm.) for their upper limit. For the information of the Committee, Lloyd's obtained from their surveyors at various works data of the carbon content, which is as follows:

Jan 2, 1919

By R. M. Brown, W. J. Murphy, B. M. Kapadia

An investigatiott was conducted to study the influence of nitrogen, titanium, and zirconium on the boron llardenabilzty effect in a low-carbon constructiona2 alloy steel. The experimental steels investigated exhibited a significant variation in hardenability, the variation being dependent on the interactions of boron, titanium, and zirconium with the nitrogen. Only the boron not combined with nitrogen was effective in increasing hardenability. Titanium, and with lesser effectiveness zirconium, combined with available nitrogen, thereby protecting the boron. The hardenabil-ity effect mas related to an empirical expression for the "effective" boron content, P, deduced from experimental evidence of these interactions. The hardenabzlity effect reached a maximum at about 0.001 wt pct 0, and decreased somewhat as P increased further. The physical understanding of this relationship is discussed. FOR many years boron has been added to steels to obtain high hardenability. Although a great deal of research has been conducted on boron-treated steels, certain aspects of the boron hardenability effect have not been fully understood. For instance, the magnitude of the hardenability effect has been observed to vary markedly, depending on the steelmaking technique, even when the amount of boron in the steel was essentially constant. Furthermore, the optimum amount of this element to be added has not been definitely established. A better understanding of the boron hardenability effect is essential because too small an addition of boron is likely to be ineffective, while an excessive amount can cause brittleness'' and hot shortness. The findings of earlier investigations have shown that the hardenability effect cannot be consistently related to the amount of boron added or retained in the steel. Grossmann observed that in a 0.60 pct C steel the hardenability increased to a maximum with mold additions up to about 0.0025 pct B and then decreased with larger additions. Other investigators5 likewise reported a maximum in the hardenability at about 0.003 pct B. Crafts and Lamont, however, found that in commercial open-hearth heats of medium-carbon steel the hardenability increased linearly with boron up to 0.001 pct and remained essentially unchanged with larger percentages up to 0.006 pct. Other investigators7,' also observed a rather constant hardenability effect in the range about 0.0005 to 0.0035 pct B. These observations and other evidence suggest that the effectiveness of boron in increasing hardenability probably depends, in addition to the amount, on the form of boron retained in the steel, this form being influenced by the presence of other elements. Both oxygen and nitrogen apparently exert the strongest influence on the hardenability behavior, since, at the temperature of liquid steel, boron readily combines with these elements, thereby losing its effectiveness as most experimental evidence seems to indicate. For consistent recovery of the boron effective in increasing hardenability, it is necessary that the oxygen and nitrogen in the steel be either reduced to extremely small amounts by the steelmaking practice or neutralized by combination with other elements before the addition of boron. The importance of achieving adequate deoxidation prior to the addition of boron in order to realize the full hardenability effect of boron has been sufficiently emphasized by earlier investigators. Digges and Reinhart' and others have investigated the role of nitrogen and have shown that nitrogen also interacts with boron and reduces or nullifies altogether its effect on hardenability. Moreover, their work also demonstrated that the addition of strong nitride formers such as titanium and zirconium reduce the deleterious effect of nitrogen on boron hardenability by combining with nitrogen to form stable nitrides. Another element which has a pronounced influence on the boron hardenability effect is carbon. It has been shown7'10 that the hardenability effect of boron diminishes with increasing carbon content, and becomes almost negligible at the eutectoid composition. This observation is useful in comparing the potential increase in hardenability from boron of steels with different carbon contents, but is not relevant to a study of the effects of normal steelmaking variables. The amounts of oxygen and nitrogen in steel vary with the steel composition and steelmaking practice employed. Most commercia1 low-alloy steels are fully deoxidized by the addition of silicon and aluminum, or other strong deoxidizers, which adequately protect the boron from oxidation. In addition, one or more of the elements such as titanium or zirconium are usually added, either separately or in combination with boron, in the form of complex ferroalloys, to protect boron from combination with nitrogen in the steel. However, the actual amount and type of addition employed for a given processing requirement are usually selected by trial and error, and have a rather limited range of applicability. As a result, substantial variations in the hardenability of boron-treated steels are often observed in practice, particularly when the nitrogen content of the steel is a significant processing variable. These variations might therefore be reasonably attributed to the interactions between boron, nitrogen, and titanium or zirconium present in the

Jan 1, 1969

By William Hutton Blauvelt

Coke is the product of dry distillation of bituminous coal, by which the volatile matter is driven off, producing a hard body of cellular structure. Not all bituminous coals will coke, and there has been much discussion regarding the substance which is present in coking-coals to distinguish them from dry coals. Professor Lewes says that the bituminous matter in coal is largely derived from the spores of fossil mosses. Resins are present in all soft coals, and contribute largely to the cementing of the coke. The resinates and hydrocarbons begin to distil out at moderate temperatures and leave the pitchy residual, which at 500' C. forms a mass already well caked together, if the proportion of humus residual is not too great. This coke is soft, but if the heat be raised to 1,000° C. the pitch decomposes further, leaving carbon, and Professor Lewes is convinced that the coking bond is due to these liquid products which distil off, leaving pitch, which then carbonizes and binds the mass into coke. Professor Parr concludes that the structures of the organic compouilds of the coal Which furnish the cemeding-material for coke, and which are apparently attacked by oxygen, have not been determined and seen] to vary somesvhat in different types of coal. However, they yield, on oxidation, humic acids of varying composition which decompose into powdery residues. Because of the complex nature of these substances and the difficulty experienced in isolating and identifying them, the theory of coking is still an open problem and the explanations advanced are largely hypothetical. In the coking process the volatile matter driven off in the oven consists mainly of tar, ammonia, and gas, familiarly known as by-products. Both the quality and quantity of coke and by-products vary greatly With the composition of the coal.

Jan 1, 1913

By J. W. Bolton

PRODUCTION of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical.

Jan 1, 1929

By W. L. Phillips

Stress-strain curves were obtained for single crystals of 70 pct Ag-30 pct Zn tested in tension and shear. Samples tested in tension and shear had comparable resolved shear stresses and stress-strain curves. The {111} <110> slip system was observed. It zoas found that the9.e is a barrier to slip in both latent close -packed directions and that the magnitude of these barriers is proportional to prior strain during easy glide. It was observed that cross-slip in tension and shear was most frequent in crystals with an initial orientation near <100> "Oershoot" zoas observed in tension. The amount of this "overshoot" was independent of initial orientation. AN idealized concept of plastic deformation indicates that a single crystal should yield at some stress that is dependent on crystal perfection and it should then continue to deform plastically by the process of easy glide which is characterized by a linear stress-strain curve and a low coefficient, d/dy, of work hardening. Hexagonal metal crystals generally conform to this ideal concept of laminar flow. In fcc metals the range of easy glide is always restricted in magnitude and it is strongly dependent on orientation, composition, crystal size, shape, surface preparation, and temperature. Since one of the principal differences between the two crystal systems, both of which deform by slip on close packed planes, is the existence of latent slip planes in the fcc crystals, it has been proposed that the transition from easy glide to turbulent flow, characterized by rapid linear hardening, is due to slip on secondary planes intersecting the primary plane.ls Several theories have been proposed to explain the linear hardening and parabolic stages of the stress -strain curve.6"10 The easy-glide region is the least understood of the three stages. The stress-strain characteristics of Cu-Zn, which shows a long easy-glide region, have been extensively investigated."-" In light of recent ideas on dislocations, cross-slip, effect of solute atoms, and stacking fault energy, it was felt that the certain features of this earlier work might be compared with another alloy, Ag-30 pct Zn, which also exhibits a long easy-glide region. Tension and shear stress at room temperatures were employed. The results obtained, together with some interpretation of the observations, are described below. EXPERIMENTAL PROCEDURE The silver and zinc used for mixing the alloys were 99.99 pct pure. The two components were weighed to within 0.1 pct of the weights required fo the alloy composition. They were then placed in a closed graphite mold and the mold and contents were heated in 100°C stages from 500&apos; to 900°C with sufficient time and vigorous agitation at each stage provided to dissolve the silver. The crucible was then heated to 1150°C and agitated violently before being quenched in oil. The resulting alloy rod was machined free of sur face defects and then placed in a graphite mold designed for growing single crystals. The graphite mold was closed with a graphite plug and was encased in a pyrex glass tube which was connected to a vacuum system. The tube and mold assembly were placed in a furnace; the tube was evacuated and the furnace was rapidly heated to a temperature sufficient for fusing and sealing the glass. The glass-encased evacuated mold and contents were then lowered through a vertical furnace. The top section of the furnace was held at 100 °C above the melting point of the alloy. The lowering rate was 1.5 in. per hr. The tension specimens were 1/4 in. diam; the shear specimens were 1/2 in. diam. These specimens were then removed from the mold, etched, and chemically polished with hot (60°C) Chase etch reagent (Crz03-4.0 g, NH4C1-7.5 g, NHOs-150 cc, HzS04-52 cc, and Hz0 to make 1 liter). In preparation for tensile testing, the specimens were carefully machined to a diameter of about 0.200 in. to permit a gage length of 6 in., annealed for 16 hr at 800&apos; to reduce coring, and then cleaned and polished. A modified Bausch-type shear apparatus which has been described previously18 were employed. The gage length was 1/8 in. This shear apparatus was placed in an Instron tensile testing machine. EXPERIMENTAL RESULTS A) Tension. Several specimens were extended at room temperature to determine the effect of initial orientation on the stress-strain curves of Ag-30 pct Zn. The initial orientation and the resolved shear stress supported by the active slip system at various total strains are plotted in Fig. 1. The critical resolved shear stress, t,, initial rate of work hardening, d/dy, and length of the easy-glide region are independent of orientation. The arrival at the symmetry line is shown by an arrow in Fig. 1. During the easy-glide region of the stress-strain

Jan 1, 1963

By Robert Goodrich

EXPERIMENTS ON A PORPHYRY COPPER ORE FROM BISBEE, ARIZ. THIS research was done partly in the non-ferrous laboratory of the Department of Metallurgy of Columbia University, under the direction of Dr. Edward F. Kern, and completed elsewhere. Acknowledgment is due to Prof. Arthur L. Walker, Dr. Edward F. Kern and Dr. William Campbell of the Department of Metallurgy, for their kind advice and for the inspiration derived from their instruction. This report is given under the following heads: Petrographic Description (Microscopic Study); Sampling and Preparing Ore for Treatment; Chemical Analysis; Treatment of Ore. PETROGRAPHIC DESCRIPTION Texture: Variable. Fine to medium mixed aggregate. Original structure: Obscure. Secondary structure: Fractured; healed.

Jan 8, 1915

By Ralph H. Sweetser

AT the end of 1943 the charcoal pig iron capacity of the United States was at the lowest point in over 1110 years, with only one strictly charcoal blast furnace in operation, and all others permanently out of blast except one in Tennessee d reported to he running on part charcoal and part coke. Such a decrease in production has taken place in spite of the O.P A.&apos;s high-premium price on charcoal pig iron of +34 per ton f.o.b. furnace in Michigan. Depletion of the hardwood supply within fifty mlles or inure of the blast furnace is the reason why; the deplorable lack of reforesting is the cause.

Jan 1, 1944

By Christie A. Callender, Harry M. Dahl

The Hobson uranium deposit is located in Karnes County, Texas, along the prominent south Texas uranium trend. The uranium mineralization occurs in the Deweesville Sandstone of the Whitsett Formation of the Eocene Jackson Group. The host rock is a friable, fine-grained, well-sorted, highly porous and permeable sandstone interpreted to be an ancient beach deposit. The sandstone contains significant volcanic constituents and ranges in composition from arkosic to tuffaceous. Locally, the host sandstone contains hard, dense opal cement. Bentonitic shales underlie and overlie the mineralized sandstone unit. Geometrically, the Hobson uranium-bearing zone resembles an elongated roll front type deposit. Chemical uranium values compared with gamma ray equivalent uranium values indicate that the uranium has been dissolved from the updip side and precipitated on the down- dip side of the roll front. Details of the uranium mineralization were studied using thin section microscopy, autoradiography, x-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) techniques. The uranium mineralization occurs in the pores of the sandstone, as grain coatings and as replacement of sand-size and smaller grains. It is commonly associated with pyrite and other opaque minerals. Other favored hosts for uranium (other than pore openings) appear to be clay aggregates, altered rock and glass fragments, and carbonaceous plant debris. Aggregates of coffinite were identified by XRD and SEM/EDS analyses. Some uranium mineralization also appears to be dispersed and is postulated to be adsorbed on the clay and carbonaceous matter.

Jan 1, 1985

By Harold B. Janzen, M. A. Nobles

Campbell and Martin1 described a new exploratory logging tool which was developed as the result of a new concept of the phenomenon that takes place when a porous formation containing mobile hydrocarbons and irreducible interstitial water is invaded by mud filtrate. They postulate that invasion will create a bank of interstitial water between the flushed zone and the undisturbed formation. This postulate was confirmed by Wyllie.&apos; Thus, if R,, is greater than R, and mobile hydrocarbons are present, the resistivity profile with increasing radii from the borehole is high:low:high, as shown in Fig. 1. If mobile hydrocarbons are absent, the bank of interstitial water is indistinguishable from the undisturbed formation and the resistivity profile, when R is greater than R,, is high:low, as shown in Fig. 2. The zone containing the bank of interstitial water and residual oil was named the "low zone". Campbell and Martin conducted extensive electrolytic wedge and resistivity analog model studies to select a logging system that would reflect the presence or absence of the low zone. The system they selected was that of a family of lateral curves. The model studies indicated that the presence of a low zone could be detected in approximately 60 to 70 per cent of the producing sand reservoirs with a family of lateral curves provided that the sonde effectively occupies 90 per cent of the diameter of the hole. These studies were conducted with D, = 5d. The presence or absence of the low zone is best determined by a plot of the apparent resistivity vs spacing as shown in Figs. 3 and 4. A dip or inflection in the profile that repeats at successive depth intervals is considered diagnostic. To reduce the shunting effect of the hole and mud, a sonde of insulating material that is surrounded by a series of flexible rubber bumpers was designed. The bumper efficiency is considered to be the ratio of the bumper diameter to the hole diameter. Field tests conducted by Campbell and Martin on 10 wells with a tool that provided for station readings indicated that dips or inflections could be detected in 19 out of 25 known producing zones. INSTRUMENT DEVELOPMENT Halliburton developed a logging system to simultaneously and continuously record eight lateral curves. The instrumentation is described in the literature.&apos; The original logs made

By C. G. Brennecke, R. T. Gallagher

This paper is the result of a research program entered into cooperatively by the General Reinsurance Corporation and Lehigh University in January 1944. The research program was instituted to find a more positive method to determine the presence of hazardous roof conditions in , mining operations. The co-authors, together with Mr. R. D. Currie, Engineer for the General Reinsurance Corporation, started working on the project in January 1944, first undertaking a library search; second, a preliminary study based on some existing equipment; third, the design of new and more suitable equipment; and finally, the field testing of equipment and methods. Purpose Any study of the accident statistics of mining operations will disclose the rather startling fact that approximately 50 to 60 per cent of all fatal underground accidents in the anthracite and bituminous mines are caused by falls of roof and coal, the metal and nonmetal mines showing only a slightly smaller percentage. Advancements in safety engineering have produced definite results in the decrease of accidents due to blasting, haulage, electricity, and explosions but no such decrease is shown in those caused by falls of roof, coal, or ore. Table Il,2 is a compilation of statistics as published by the United States Bureau of Mines, showing the percentages of fatal accidents caused

Jan 1, 1947

By R. T. Gallagher, C. G. Brennecke

This paper is the result of a research program entered into cooperatively by the General Reinsurance Corporation and Lehigh University in January 1944. The research program was instituted to find a more positive method to determine the presence of hazardous roof conditions in , mining operations. The co-authors, together with Mr. R. D. Currie, Engineer for the General Reinsurance Corporation, started working on the project in January 1944, first undertaking a library search; second, a preliminary study based on some existing equipment; third, the design of new and more suitable equipment; and finally, the field testing of equipment and methods. Purpose Any study of the accident statistics of mining operations will disclose the rather startling fact that approximately 50 to 60 per cent of all fatal underground accidents in the anthracite and bituminous mines are caused by falls of roof and coal, the metal and nonmetal mines showing only a slightly smaller percentage. Advancements in safety engineering have produced definite results in the decrease of accidents due to blasting, haulage, electricity, and explosions but no such decrease is shown in those caused by falls of roof, coal, or ore. Table Il,2 is a compilation of statistics as published by the United States Bureau of Mines, showing the percentages of fatal accidents caused

Jan 1, 1947

By B. Ball, D. W. Fuerstenau, P. C. Kapur

A two-phase distributed-parameter model of the flotation process has been extended to allow consideration of the important process parameter, concentrate grade. A simple expression is presented for the grade of concentrate in terms of the zeroth and first moments of the concentrate distribution. An example is given for a binary ore containing two pure minerals each having nondistributed rate constants. For extend-ing the model to the distributed rate constant case, a cubic polynomial zoas utilized to simulate the feed distribution. One particular example is considered and grade-recovery curves are generated to show the dependence of such curves on the initial feed distribution. Operating flotation plant engineers have traditionally evaluated plant performance in terms of the recovery of valuable mineral and the grade of the concentrate. In both operation and research, grade-recovery relationships have been used as a guide for selecting flotation conditions. Weissl illustrated the use of grade-recovery curves in plant operation and considered the grade-recovery relationship to be a metallurgical one. The extensive experimental work of Chi" using standard batch flotation tests on iron ores shows that, even with extensive statistical correlation of data, little insight can be gained into the basic fundamentals of these relations. Such relations must depend on the kinetic behavior of the various mineral species in the flotation circuit. In his flotation text book, Gaudin3 considered the relationship of recovery and of product grade to flotation kinetic indices, but he did not extend his calculations to yield grade-recovery relations. Although Gaudin used a simplistic model for his analysis, he did recognize that variations in flotation rates must result from variations in locking, surface heterogeneity, particle size and shape, among other things. In a recent paper,&apos; we presented a model of the flotation process that could be readily analyzed with an analog computer. This model combines the concept of a distributed set of rate constants"" with that of the two-phase flotation model,8" resulting in a model more powerful and flexible than previous ones. The purpose of the present paper is to show how this model can be used to generate grade-recovery curves and to determine the dependence of such curves on the various kinetic parameters. In this paper, the model will be limited to the semi-batch case, but extension to the continuous case is a straightforward step.

Jan 1, 1971

By Edgar R. Kendall

A knowledge of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. Locating the Supply The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1942

By Edgar R. Kendall

A knowledge of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. Locating the Supply The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1942

By H. R. Aldrich

This paper is not a treatise on the theory and practice of magnetic surveying. It presents a diagram upon which have been plotted observations taken with the simplest form of magnetic instrument, the lowly dip needle, over a large area astride the Lake Superior syncline of northern wisconsin. The exposures of the underlying formations are not sufficiently great in number nor fortunate in distribution to have provided the fuller understanding of the geology which has been secured by the use of the magnetic observations as an auxiliary tool or accessory in the hands of the geologist. The diagram (Fig. 2) in large part speaks for itself if studied in connection with the geological map (Fig. 1) for which it is the main control. It is presented to demonstrate the extent to which the use of such methods may aid in the solution of geological problems in a covered country. The diagram is probably unique in assembling the expression of such a wide range of formations, affected by so wide a range of secondary processes, and deformed by so many different structures in terms of magnetic variation. Few geologists outside of the Lake Superior country have had any first-hand experience in the taking of magnetic observations and the interpretation of the results in terms of geological conditions; nor have the Lake Superior men gone with the methods far afield from the mere tracing of iron formations. In more recent years the oil companies have gone heavily into investments in magnetometers, balances, and dip needles in the quest of concealed structural anomalies which are the favorable loci of petroleum accumulation. But these geophysicists come back from the fields with their collections of observations facing the question of interpreting the geological meaning of their magnetic anomalies. It is considered probable therefore, and certainly it is the hope of the writer, that the appended charts, or magnographs, which show how character of the country rock and its changes, structural strike and dip and their changes, depth of burial and its variation, contact metamorphic

Jan 1, 1929

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory investigatorsstate of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which andare useful for predicting machine performance and give acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary canexplain commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted.&apos;TheRittinger In its first form, as stated by P. R. Ritted.&apos;tinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include the concept of surface energy; in this form it was precisely stated by A. M. Gaudin&apos; as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended." According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported- hat support the theory in its first form by indicating that the new surface produced in different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work done on the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading, since it does not follow the regular breakage pattern of most materials but is regularrelativelybreakage harder to grind patternat the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory4 is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr /log 2." The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-l.V f a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The evaluation in terms of kw-hr per net ton of —200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of —200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1953

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory investigatorsstate of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which andare useful for predicting machine performance and give acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary canexplain commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted.&apos;TheRittinger In its first form, as stated by P. R. Ritted.&apos;tinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include the concept of surface energy; in this form it was precisely stated by A. M. Gaudin&apos; as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended." According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported- hat support the theory in its first form by indicating that the new surface produced in different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work done on the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading, since it does not follow the regular breakage pattern of most materials but is regularrelativelybreakage harder to grind patternat the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory4 is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr /log 2." The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-l.V f a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The evaluation in terms of kw-hr per net ton of —200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of —200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1953

By W. B. Hall, Joy D. Lewis

Mine-run ore is received at Vitro in gondola cars and fed directly to a Cedar Rapids impact crusher. Following screening, the undersize travels through a recently installed three-stage sampling plant where successive cuts are executed by conventional Geary-Jennings type cutters to produce a final sample of 1 lb per ton of raw ore fed. Crushed ore is transported to one of three storage silos or to stockpile, depending upon grade and type of amen- ability. This permits the blending of a mill feed with some degree of consistency. Final grinding is accomplished in one of two closed circuit ball mill-classifier systems allowing simultaneous processing of two basic types of ores. High acid consumers may be leached separately in the required environment. Part of the free acid remaining can then be utilized by an ore stream entering later whose component ores require much less free acid for leaching.

Jan 11, 1958