Search Documents

By J. S. Vanick

An extremely hard, tough, and strong, white or chilled cast iron has been applied for the past several years to industrial and mining services in which its unusual properties have been confirmed by its ability to deliver in many instances much better performance than plain chilled iron, or other wear-resistant materials. It is being produced regularly by alloying a good base composition of chilled or white cast iron with essentially 4 to 6 per cent of nickel and 1 to 2.5 per cent of chromium. Such a material can attain a hardness exceeding 600 to 750 Brinell as against 380 to 530 for corresponding grades of plain chilled iron. The strength is approximately doubled and the toughness significantly increased. These properties make it especially useful for many applications requiring a high hardness for resistance to wear, abrasion, attrition, deformation; to some extent to high compressive loading and to a lesser but important degree to corrosive action. A wide variety of commercial castings is being successfully produced from this iron, ranging in size from the small grain-grinding plates or burrs through medium-sized castings such as sand pumps up to large, heavy castings such as rolls for metal rolling or cement grinding. The composition of this white cast iron may be roughly bracketed within the range shown in Table 1.

Jan 1, 1933

By K. G. Wikle, J. G. Klein, W. W. Beaver

Consolidation of hydride process, electrolytic, calcium reduced, and comminuted thorium powder, as well as saw chips and lathe turnings, by vacuum hot pressing and by cold pressing-vacuum sintering was studied. The mechanical properties of the consolidated material in the extruded form are compared with those of wrought castings. AT present there little little industrial use for thorium metal, although it has some important though small scale applications in electronic equipment. Despite its high inelting point—about 1750°C —a low modulus of elasticity, 11.4xl0 si at 20°C;' relatively low mechanical properties coupled with a high density, 11.7 g per cu cm; and an unusually high chemical activity with normal atmospheres limit any structural applications. The metal is utilized as an alloying element principally in magnesium. Pure thorium finds utility as electrodes in gaseous discharge lamps such as the high intensity mercury lamp' because its low work function and high electron emissivity provide lower starting potentials and more uniform operating characteristics than other available materials. The metal is also found in photoelectric tubes used for the measurement of the ultraviolet spectrum." Thorium metal has been used in germicidal lamps of the cold cathode type as sputtered coatings on nickel in order to provide a low work function surface and a low starting voltage. Other applications have involved the radioactive properties of thorium for the production of ionized particles." The potential value of thorium is much greater than its present use pattern because of possible utility in the field of nuclear power. Th may be converted through nuclear reaction to a fissionable element U which should be capable of acting similarly to U in the g'eneration of atomic power. Thorium has been reported to be about three times as plentiful as uranium in the earth's crust, placing it in the order of abundance of lead and molybdenum." Thus, it is of interest in augmenting the potential supply of fissionable material for nuclear power. Because of its high melting point, thorium is usually produced as a powder through the calcium reduction of its oxide or thermal reduction of halides by sodium, magnesium, and calcium. It may also be produced in flake form by electrolysis of fused alkali or alkaline earth chloricles and fluorides. Therefore, powder metallurgy assumes importance in the fab- rication of thorium metal shapes. Furthermore, it is rather difficult to obtain pure thorium by melting, as the molten metal reacts readily with graphite as well as oxide, carbide, and nitride refractories. These contaminate the melt with oxides, carbides, and metallic impurities." The current investigation was undertaken to examine the fabrication of thorium by powder metallurgy methods which have been used for the commercial production of beryllium and other metals.' A sparcity of data concerning the comparative cold and hot compaction of thorium powders of different derivation existed. Therefore, all commercially available types were examined along with other experimentally produced thorium powders in order to round out the comparison of consolidated thorium powders with melted reguline metal. Review of the Literature By heating a mixture of ThC1, with potassium, Berzelius made the first thorium metal as an impure powder in 1828. Improvements in the basic process, increasing thorium assay to 99 pct, were made by several investigators including Arsem," Lely and Hamberger10 and Von Bolton." Calcium reduction of Tho, to make powders was investigated by Berger," Huppertz,'" Kroll," and Kuzel and Wedekind.'" A thorium powder produced by this method using a CaC1, fluxing agent assayed 99.7 pct, as reported by Marden and Rentschler.'" Compacted and sintered, this product was found to be ductile, and could be fabricated into wire and sheet. Improvements of the calcium reduction process were made later" wherein CaCl, was eliminated from the reaction, producing metal assaying 99.8 pct Th. Further work by Lilliendah118 howed that a coarser metal could be obtained by the substitution of ThC1, or ThOC1, for oxide with consequent advantage of stability to atmospheric reaction. Reports on the technology of thorium developed in Germany during World War II have been made by Espe."' Thorium powder of 99.5 pct Th was obtained by reduction of the oxide by calcium. Screening to —200 mesh, compacting with about 20 tsi, and sintering in vacuo at 1320" to 1360°C for 3 hr resulted in a porous sinter cake. The sinter cake was sufficiently ductile to be worked into bar, wire, and sheet which could be employed as electrode materials.

Jan 1, 1957

By Mark J. Klein

The precipitation of nitrogen in quenched and aged CY-35 at. pct Re was followed by internal-friction and electrical-resistivity measurements. It is shown that the precipitation kinetics of nitrogen from solution are many orders of magnitude lower in this alloy than in chromium. The reluctance of nitrogen to precipitate from sol~ction can be attributed to the composilional r-eadjustnzents required in the z.icinity of a chromium nitrade particle for gowth to occur. AS part of an investigation of the mechanism by which rhenium increases the low-temperature ductility of chromium and other Group VI-A metals, it was of interest to compare the concentration of interstitial elements retained in solution in chromium with that of a ductile Cr-Re alloy. The presence of certain interstitial elements in chromium has been shown to decrease its ductility1-5 and, of these interstitials, nitrogen is believed to have the most detrimental effect on mechanical properties. Thus, a comparison of the disposition of nitrogen in chromium with that in a ductile Cr-Re alloy might provide information about the mechanism whereby rhenium enhances the ductility of chromium. In previous internal-friction studies it was shown that the equilibrium solubilities of nitrogen in chromium and Cr-35 at. pct Re did not differ greatly.= However, results indicated that the actual concentration of nitrogen retained in solution at ambient temperatures is likely to be considerably greater in the alloy than in chromium because the precipitation kinetics of nitrogen are greatly retarded by the addition of rhenium. The objective of this investigation was to study the kinetics of nitrogen precipitation in Cr-35 at. pct Re in greater detail and to obtain information concerning the mechanism of nitrogen precipitation in this alloy. The properties studied were internal friction and

Jan 1, 1967

By B. M. Larsen, W. E. Shenk

THIS paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable that is, the time interval between successive reversals-should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one "minimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: x. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potentiometric control instrument, to correct any

Jan 1, 1945

By Charles S. Barrett, Hermann F. Kaiser, Robert F. Mehl

THE copper-silver system presents several points of special interest in the study of segregate structures. The system is simple eutectic, with limited solid solutions terminal with the pure component metals. The extent of solid solubility decreases with decreasing temperature for both the copper-rich and the silver-rich alloys, thus offering a possibility for the formation of Widmanstätten figures and also a possibility for aging after quenching. In contrast to the structures studied previously the structures in this system are unique in their origin, for one terminal solid solution will precipitate the other, and vice versa. In most of the other systems for which crystallographic data on the precipitation (or transformation) process are available, either intermetallic compounds or intermediate phases partake in the decomposition process; the absence of such phases thus distinguishes this system. The lattice structures of the two solid solutions are identical in type, differing in lattice spacing by approximately 10 per cent; because of this it seems difficult if not impossible to predict on the basis of present theory either the outward form of the precipitate or the lattice orientation relationships between matrix and precipitate. The eutectic temperature in the copper-silver system1 is 779° C. At this temperature copper dissolves 4.3 atomic per cent (7.0 weight per

Jan 1, 1935

By J. V. Richards

The Altar district, State of Sonora, Mexico, is for the most part a desert with but little rain-fall and few running streams. On account of this scarcity of water it is necessary for the natives to " dry-wash" the placer-gravel, and the object of the present gaper is to describe some of the more commoil Mexican dry-mashing devices. My observations were confined to a property known as Las Palomas placers, 15 miles from the Gulf of California and about 150 miles south of the United States border; a brief description of which property may be of interest as illustrating what is, perhaps, a typical Sonora dry placer. It is said that as long as a century ago the Yaqui Indians discovered rich cement-gravel, known as argo masa, at Las Palomas, and that there has been a more or less steady production of gold from the property ever since. The argo masa, is a fairly-coarse gravel, the pebbles being quite firmly held together with a lime cement. Gold is scattered through this cement in particles ranging from fine specks to pieces several grams in weight, and occasional large nuggets are encountered. The contents vary so widely that it is difficult to estimate the average value, but returns of from $10 to $50 per cubic yard are common, and it is doubtful if the Indians considered anything less than from $4 to $5 a yard as "pay dirt.'' This ar-90 masa, occurs in channels varying in thickness from a few inches to several feet, and in width up to 300 ft. These channels are continuous and are probably ancient stream-beds. They are for the most part covered with an over-burden of a more recent gravel, varying from 30 to 50 ft. thick, and the fact that this over-burden contains values as high as $1.50 per cubic yard, and yet was not worked by the Indians, shows that their idea of what constituted mas high.

Jan 1, 1911

By A. G. McGregor

DURING the past 5 years, five new copper-smelting plants have been built and put into operation in the State of Arizona. The monthly copper output from these plants averages from 5,000,000 to 18,000,000 lb. Previously, there never was as much activity in copper-smelting plant construction in the same length of time in all the rest of the world. Naturally, in this amount of work, some new problems were met and new features in plant design and. equipment developed. Some of these features are described in this paper. CONCENTRATE HAULING, UNLOADING AND SAMPLING SYSTEM (a) Concentrate Car The International Smelting Co. has provided at its plant at Miami specially designed cars for hauling the concentrates from the mills of the Inspiration Copper Co. and the Miami Copper Co.. The car has a bottom that is readily made tight to hold flotation concentrates and is quickly and cheaply unloaded. Figs. 1, 2 and 3 show views and details of the car. The main feature of this car is the slot in the bottom throughout its length, which is closed by means of short planks that overlap like ship-lap as shown by Fig. 1. At one end of the car an iron gate operated by a screw and hand wheel is provided, which clamps or presses the planks together, making the bottom tight. A removable tapered plug rests vertically over this gate when the loading of the concentrates at the mill commences.

Jan 8, 1916

By J. Szekely, Robert J. Fisher

A formulation is Presented and solutions are given for the problem of transient heat conduction in a sphere that undergoes a spatially uniform radiative heat exchange with its environment. The solutions were obtained by the numerical integration of the appropriate Partial differential equation and are Presented in a graphical form by Plotting a dimensionless average temperature against the Fourier number with the radiation number as a paranreter, for various initial sphere and environment temperatures. In addition to these numerical results asymptotic analytical solutions are also given. PROBLEMS involving the transient heating or cooling of droplets and particles frequently arise and are of importance in metallurgical operations. Spray refining, vacuum degassing, high-temperature gas-solid reaction systems, and pebble heaters are but few of the numerous examples that may be quoted. The practical interest in these problems from a design or operational point of view is to evaluate the change in the particle temperature with the time given its physical properties, initial temperature, and that of the environment. At the high temperatures encountered the principal mode of heat transfer between the particles and their environment is by thermal radiation; in case of vacuum degassing due to the very low thermal conductivity of the gas space the convec-tive components are negligible and radiation is the only heat transfer mechanism. Although much work has been done on transient heat conduction problems, the special class mentioned here, in which thermal radiation is specified at the bounding surface, received little attention to date. One contributory factor to this situation may be the nonlinearity of the radiation term in temperature, which in general precludes the use of analytical techniques and requires numerical or analog solution of the appropriate differential equations. In fact the only solutions of general nature that are available at present pertain to semi-infinite media and slabs.'-3 The work on which the paper reports forms part of a program aimed at the theoretical and experimental study of transient radiative heat exchange between particles and their environment. The purpose of the present paper is to develop a formulation and solutions to the problem of transient heat conduction in a sphere that undergoes a spatially uniform radiative heat exchange with its surroundings. The solutions, obtained by the numerical integration of the appropriate differential equations, will be presented graphically, by plotting dimensionless parame- ters covering the range of variables relevant to metallurgical interests, thus affording a ready reference for design calculations. In addition to these results, approximate analytical solutions are also given which represent asymptotes, corresponding to extreme values of the variables mentioned. FORMULATION Consider a spherical particle of radius, a, initially at uniform temperature, Ti (T measured on the absolute scale), having a thermal conductivity, k, density, , specific heat, C, and thermal diffusivity, a. At time = 0 let this particle be exposed to an environment which is at a temperature T, and subsequently let there be a purely radiative heat exchange between the particle and the environment resulting in a spatially uniform heat flux at the surface. If in addition to the above we make the assumptions that the sphere is a gray body radiator, homogeneous, isotropic, and opaque, and that the physical properties are independent of temperature, conservation of heat in the sphere may be written as follows: The boundary condition contained in Eq. [3] states that the initial temperature of the sphere is considered uniform, equalling Ti, whereas Eq. [4] is readily obtained from symmetry considerations. Eq. [5] expresses the continuity of the heat flux at the surface of the sphere, or in other words the condition that the rate of heat exchange between the sur-

Jan 1, 1969

By Thomas L. Kesler

The Cartersville mining district, 35 miles northwest of Atlanta, Ga, has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. General Geology Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisnerl in this region, supposedly partly or. wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady† formation, also of Lower. Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1941

By Thomas L. Kesler

The Cartersville mining district, 35 miles northwest of Atlanta, Ga, has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. General Geology Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisnerl in this region, supposedly partly or. wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady† formation, also of Lower. Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1941

By L. E. Mannion

Sodium carbonate or soda ash is one of the two principal alkalis of commerce, the other being sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines or solid salts were the source of impure soda for glass manufacture. In early modern times until the 19th century, soda ash, as well as potash, was recovered mainly by leaching the ashes of plants. In Europe, during the 18th century, a brown lye for laundering was produced by pouring hot water over burned seaweed. One of the better grades of this kind of material was a product from Spain termed "barilla," which analyzed 24 to 30% Na2CO3 (Hou, 1942). The birth of the modern chemical industry may be said to start with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. Although invented in France in 1691, England made the most extensive use of it. In 1863 Ernst Solvay devised the ammonia-soda or Solvay process, and by 1874 the first of many Solvay plants was built. These were to supplant the LeBlanc method and dominate soda-ash production until the present time. Although of lesser importance, natural sodium carbonate deposits continued to support operations in various parts of the world. Shortages during World War II stimulated production of "natural" soda ash, particularly at Searles Lake, Calif., and at Lake Magadi, Kenya. Within the last ten years in the United States, a notable surge in production has occurred based on the vast trona deposits in Wyoming. Table 1 lists some principal producers of natural soda ash and the character of the source deposits. Uses and Specifications Sodium carbonate (Na2CO3) is a white, crystalline hygroscopic powder, an aqueous solution of which is strongly alkaline. Most commercial soda ash is a product that must meet high standards of purity and uniformity. Two forms are commonly sold: a fine, powdery material called light ash, and a more coarsely crystalline dense ash; these weigh 32 to 39 and 60 to 66 lb per cu ft, respectively. Dense ash may be produced by adding a little calcium chloride to the sodium carbonate solution to control crystal size and prevent agglomeration. Specifications and typical analyses of light and dense ash in the United States are shown in [Table 2]. Sizing generally achieves about 75% of light ash and 90% of dense ash between +30 and -100 U.S. screen mesh. World use of sodium carbonate now exceeds 24 million tpy, of which the United States produces more than 7 million tons. The market for soda ash is dominated by the glass industry, which uses almost half the supply. Inorganic chemicals, including phosphates and silicates, consume about 30%. Other principal uses include the manufacture of soaps and detergents, petroleum, caustic soda, organic chemicals, and paper; and nonferrous and ferrous metallurgy. [Fig. 1] shows the percent consumption by use of soda ash in Europe, Japan, and the United States. The price of soda ash in the United States remained relatively stable during the 1960s at about $33 per ton; in 1972 it reached $35 per ton. The price in 1975 was $42 per ton. Geology Mineralogy [Table 3] is a list of the more common sodium carbonate-bearing minerals. Anhydrous sodium carbonate is almost never found in nature; only natron, thermonatrite, and trona have been used directly as sources of sodium carbonate. At Searles Lake, burkeite and hanksite are important in the reconstitution of

Jan 1, 1975

By L. T. Hiaains

EVEN before the surrender of Germany, a gradual reduction in output of many of the small mining iseswises in the different countries of South America had occurred. Part of this was due to restricted purchases of strategic mineral supplies, and part to economic conditions. Inflationary tendencies have keen increasing since the war started; out in the past three years they have become serious. The difficulty in obtaining supplies, and labor troubles, has also combined to reduce production in many circumstances. British Guiana The Cuyuni Goldfields, Ltd., operating he Aleck Hill mine, is increasing their yanked mill to 500 tons. This appears be one of the few important new developments in South America during recent years. Brazil The big Volta Redonda steel plant was sported as being ready to start operations. Argentina Political troubles have restricted activities during the past year, and fuel short. ges have been so acute that surplus corn as burned in some instances. Practically all the tungsten producers ther closed down entirely or reduced

Jan 1, 1946

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization-one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. INTRODUCTION Buchans is 5 miles north of Red Indian Lake, in Central Newfound- land, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller- town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Ch, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company's testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

By George D. Graffin

The first use of graphite is lost in the mists of time. It was used by primitive man to make drawings on the walls of caves and by the Egyptians to decorate pottery. As early as 1400 A.D. graphite crucibles were being made in the Haffnerzell district of Bavaria. Through the Middle Ages graphite was confused with other minerals, especially galena and molybdenite. Two common names that are still used for the mineral are "Plumbago," meaning leadlike, and "Black Lead." The latter name implied that graphite is either composed of lead or at least contains a large percentage of it. Gessner is credited with having recognized it as a separate mineral in 1565, but its composition was not determined until 1779, when Scheele demonstrated that graphite oxidized to carbon dioxide, thus proving its carbon constitution. In 1789, Werner named it "graphite" from the Greek word "graphein," meaning to write. The United States has long relied on foreign countries for its graphite supplies. This reliance has been due more to the lack of suitable domestic graphites than to any particular preference for buying minerals overseas. Ceylon (now Sri Lanka) graphites were imported as early as 1820, and Madagascar graphites have been imported since the properties on that island were opened up about a hundred years later. Mexico has long supplied the United States with most of its requirements for amorphous graphite. Physical Properties and Classification Graphite is found in laminated, flaky aggregates disseminated in schistose rocks. It also occurs in veins and exhibits a foliated or fibrous structure. Graphite is a black lustrous mineral that crystallizes in the hexagonal system, with rhombohedral symmetry. The crystals have tabular form and are six-sided; the faces are commonly striated. The flakes have perfect basal cleavage and are opaque. When well crystallized, the flakes have a black metallic luster while the amorphous material is black and earthy, with a microcrystalline compactness. The flakes feel greasy. Graphite is an excellent conductor of heat and electricity. It melts at approximately 3500°C and sublimes at about 4500°C. It is combustible in the presence of oxygen between 620° and 670°C, but is stable and chemically inert at ordinary temperatures.

Jan 1, 1975

By Bernt Ellingsaeter, Terkel Rosenqvist

IN the silicothermic reduction of magnesia, burned dolomite is treated with high grade ferrosilicon in an evacuated steel retort at temperatures between 1150° and 1200°C. The following reaction is assumed to occur MgO + CaO + 1/2 Si (Fe) - Mg(g) +- & Ca,SiO, + Fe with the equilibrium constant on the basis of thermodynamic data for the substances involved and assuming unit activity for all solid constituents, Kubaschewski and Evans' calculated the magnesium pressure as a function of temperature logp,, (mmHg) = 15.06-1.61 T- log T- 13,16O/T. Pidgeon and King," who measured the magnesium pressure by means of a flow method, found values about three times the calculated ones. This may be caused by uncertainties in the thermodynamic data, but may also be caused by the formation of other reaction products, such as Ca,SiO,, which is known to be the stable silicate in equilibrium with lime. Whatever the exact reaction may be, it is evident that as long as all other factors are maintained constant the magnesium pressure will vary with the silicon activity, viz: p,, = &,. (p,,) ", where (p,,)" is the magnesium pressure by the reduction with silicon of unit activity. In the present investigation, p,,, was therefore measured for various grades of ferrosilicon and their silicon activities were calculated. The experimental method was similar to that used by Pidgeon and King. Briquettes of burned dolomite and Fe-Si alloys were placed in a 1 in. heat resistant steel tube and were heated to 1200°C. By means of a flow of purified hydrogen, the magnesium vapor was swept into a condenser filled with steel wool. From the amounts of hydrogen used and magnesium condensed the magnesium partial pressure was calculated. First a tube of 28 pct Cr steel, and later a tube of Kanthal D (a ferrous alloy with 22.6 pct Cr, 2 pct Co, and 4.5 pct Al), was used as a heat resistant tube. The latter tube showed the best heat resistance. The dolomite used had the following composition: 43.6 pct MgO, 55.5 pct CaO, 0.2 pct K,O + NalO, 0.2 pct Fe,O,, and 0.3 pct insoluble. The ferrosilicons were prepared from 98 pct Si of technical grade (0.7 pct Al, 0.3 pct Ca, and 1 pct Fe) by melting with various amounts of electrolytic iron of high purity. The alloys thus obtained were analyzed on their iron and silicon contents, which added up to between 99 and 100 pct. The amounts of reactants were chosen so that there would always be an excess of the oxides, and the average decrease in silicon content during the experiments would be about 1 pct. Most of the reaction occurred in the part of the reaction mixture facing the gas flow. The change in the silicon concentration in the part facing the condenser was, therefore, negligible. To facilitate the reaction, about 1 pct fluorspar was added to the briquette mixture. Fluorspar does not enter the reaction, but is known to act as a

Jan 1, 1957

By J. Lemish

Considerable research has been conducted in Iowa in recent years on carbonate aggregate reactions in concrete. Groups outside the state have become active in the past few years after recognizing that certain carbonate aggregates are reactive in concrete. The paper reviews the nature and extent of the problem and a summary is given of research by the author and his associates. In recent years considerable research has been conducted in Iowa on carbonate aggregate reactions in concrete. The research is part of a general study on the behavior of carbonate rocks as concrete aggregates sponsored by the Iowa State Highway Commission. Research on carbonate aggregates has not been extensive in the past. Laughlin1 published one of the first papers on carbonate aggregates in 1928 and was followed by others, notably H. S. sweet,' B. Mather et al.,3 and K. Mather4 who emphasized the petrographic and physical aspects of carbonate aggregates. The recognition that certain carbonate aggregates are reactive in concrete has led to increased participation in research in the past few years by groups outside of Iowa. Significant contributions have been made by Swenson and Gillot,5 Hadley,6 and Chaiken and Halstead7 in work which emphasizes the expansion of carbonate rocks in alkaline environments and the reaction of carbonate minerals or dedolomitization with alkalies. It is the purpose of this paper to review briefly the nature and extent of the problem and present a summary of the research by the author and his associates. EXTENT AND NATURE OF THE PROBLEM The problem is the deleterious behavior of certain carbonate aggregates in concrete. It was first recognized in Iowa over 20 years ago when poor service records of certain highways were correlated with aggregates produced from the Glory and LeGrand quarries. Deleterious behavior of carbonate aggregates have been reported in Canada and, more recently, in New York and Virginia. As more knowledge is gained concerning the problem, distress in concrete related to carbonate aggregates may be recognized over a widespread area. The problem may potentially exist in the Midwest, the Northeast, and other parts of the country underlain by thick sections of carbonate rocks readily available for utilization as aggregates. The nature of distress in Iowa highways is a general weakening and deterioration of concrete characterized by progressive cracking and spalling away from joints and edges (Fig. 1). The distress generally occurs after 15 years of service and becomes progressively worse. Specimens of such concrete lack the toughness of sound concrete and break easily under the hammer in the manner of a soft brick. The matrix is generally highly carbonated and dark borders, or reaction shells or rims outline the argillaceous carbonate aggregate fragments (Fig. 2). Cracks observed in cores cut across the aggregates and concrete matrix. Although localized volume change (expansion) is associated with spalling, there is no definite field evidence in Iowa that excessive growth of concrete slabs has occurred. The experience with carbonate aggregates in Iowa indicates that the concrete deterioration is not the same as that induced by the alkali-aggregate reaction associated with siliceous aggregates. The principal difference is that in Iowa the distressed concrete is weakened throughout the slab. In concrete affected by the alkali aggregate reaction, the

Jan 1, 1961

By O&apos, R. G. Meara, M. M. Fine

One of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite. † In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.' The outlook for the postwar market for fluorite is encouraging Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status3 Acknowledgment This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. 0. E. Anderson, mill superintendent,

Jan 1, 1947

By M. M. Fine, R. G. Meara, O&apos

One of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite. † In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.' The outlook for the postwar market for fluorite is encouraging Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status3 Acknowledgment This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. 0. E. Anderson, mill superintendent,

Jan 1, 1947

By S. Harries Daddow

THE INSUFFICIENCY OF PILLARS OF COAL FOR THE PURPOSES DESIGNED-THE FRUITFUL CAUSE OF DANGER, EXPENSE, AND WASTE-THE PROOF OF INSECURITY-SUBSTITUTE FOR PILLARS OF COAL-PILLARS AND PANELS COMPARED. PILLARS of coal, which are designed and left in our mines as the means of supporting the overlying strata of our coal-beds, and securing protection to the miner, are not only insufficient for these purposes, but the most objectionable means of providing the desired security to life and property. Though such pillars are left at a great sacrifice to the owners of collieries and mineral lands, loss to the resources of the commonwealth, and ultimate privation to the public, they defeat the very ends for which they are designed, and not only do not secure life and property, but are as fatal to the one as ruinous to the other. Propositions.-It is eminently desirable that the resources of the commonwealth-particularly our mineral wealth in anthracite coal, which is limited-should be carefully utilized and made available, not only to ourselves but our posterity. Yet, speaking as an anthracite miner, we are wasting our resources of coal with a recklessness which will bring ruin in the end, unless checked, not only to the iron manufacturing interests of the East, whose chief protection, in competition with the iron-masters of the interior, lies in a cheap and abundant supply of anthracite furnace fuel, but to the best interests of the State. It is, consequently, not only desirable, but necessary, that we should realize every ton of coal from each colliery, and every acre of coal area, in order that our resources may not be wasted at present, to breed want in the future, and to realize the greatest present benefit to the mine, the miner, and the public. It is not possible, however, to secure these ends, if we continue to leave, as we do at present, from one-third to one-half our resources in anthracite as pillars in our mines. But our sad bills of mortality, our abandoned collieries, and our yawning mountain-sides, present ample evidence that even this enormous waste of coal, though left for the purpose of protecting life and property, is as totally inade-

Jan 1, 1873

By O. W. Ellis

CERTAIN alloys1 that, as a result of quenching, are retained in the form of homogeneous solid solution are known to increase in hardness and strength on standing at room temperature or on heating at slightly elevated temperatures. Other alloys" that, on rapid cooling, are held in the form of homogeneous solid solution (as, for example, certain steels) behave in like manner on heating to somewhat higher temperatures. The observed increase in the hardness and strength of these alloys, referred to as "aging" or as "secondary hardness," is widely accepted as being occasioned, either in whole or in part, by the precipitation in submicroscopic form of such constituents as were held in supersaturated solid solution as a result of cooling in excess of a certain critical rate. In earlier discussions of the cause of age hardening or secondary hardness, the question of the hardness of the precipitated particles does not appear to have been raised. At present, however, the general opinion appears to be that age hardening and secondary hardness are occasioned by the precipitation of hard particles within the supersaturated solid substance.3 The authors may be wrong in their belief that the last is a prevailing opinion. Nevertheless, it is thought that the following experiments,

Jan 7, 1924