Search Documents

By M. L. Leonardi

THE Searles Lake orebody is located in the north- west corner of San Bernardlno County. It is a dry lake bed with an exposed salt surface covering an area of 12 square miles. Recoverable mineral values are contained in the mother liquor below the surface of the lake. Stratification in the lake bed has separated the brine into two bodies which dlffer in composition. Although liquor is processed from both bodies, this paper will discuss only the upper structure brine. Fig. 1 illustrates a typical cross-section of the two commercial orebodies. The orebody is composed of a porous salt deposit 70 to 90 ft deep. The upper structure is separated from the lower orebody by a 12 to 16-ft thick impervious mud seam, as shown in Fig. 1. These salt structures are composed of 55 pct solid-phase salts and 45 pct voids which are filled with the original mother liquor. The brine wells are drilled to the separating mud seam and cased to wlthin 10 ft of the bottom. This is done to draw the brine horizontally from the bottom of the structure. It is pumped with multistage centrifugal pumps Into the plant at the rate of 3 milllon gal per day. The first process that was successful was developed by Charles P. Grimwood for the recovery of potash. The first evaporator unit was built in 1916. In the early twenties, Dr. Morse worked out a process for the recovery of borax. This made the cycle more efficient, as the end liquor could be sent back to the evaporators rather than being sewered. In 1926 the American Potash & Chemical Corp. was formed as a new company, and the entire plant was remodeled. The plant at that time produced only potash, borax, and boric acid. Since then the American Potash & Chemical Corp. has added processes for the production of USP boric acid, refined potash, sulphate of potash, soda ash, salt cake, lithium concentrates, Pyrobor (Na2B4O7) bromine, phosphoric acid, and lithium carbonate. The main plant cycle may be depicted as a closed cycle, see Fig. 2. The raw material, brine, enters the cycle to be mixed with the end liquor, known as ML2, from the pentahydrate borax crystallizers. The mixture of these two forms evaporator feed. Evaporator feed is pumped to the evaporators where it is concentrated, with respect to potash and borax. In the same operation water vapor, sodium chloride, salt trap salt, and clarifier salt are removed from the cycle, see Fig. 3 for potash plant product. The evaporators produce a concentrated liquor which contains approximately 19.5 pct KCI. This liquor is diluted as it enters the potash plant to keep all salts, except potash (KCI, 97.0 pct) in solution. Here the moist potash leaves the cycle at 100°F. The end liquor, known as ML1, is pumped to the borax pentahydrate crystallizers, where crude borax pentahydrate is crystallized and removed as solid phase. The ML2 is sent back to pan feed to be reconcen-trated, see page 207. Note that the only water to leave the cycle is in the form of vapor and moisture in the solid phase products crystallized. Thus there is a constantly cycling volume of liquor to which brine is added. Since the volume of liquor cycled does not increase, the brine is, in effect, evaporated to dryness. This would be true if there were no liquor losses. But, as in all processes, there are always unavoidable and accidental losses which reduce the volume of cycling liquors. The losses must be made up with brine. The concentration process is the beginning and the end of the cycling liquors. In this process there are three evaporator units of the triple effect counter-current type, that is, there are three pans in each unit and the heat flows in one direction while the liquor flows the other way through the evaporator pans, see Fig. 4. During the evaporation process a great deal of sodium chloride, burkeite, some sodium carbonate monohydrate, and a little lithium-sodium phosphate are crystallized. The volume of these salts is so great that they must be removed as they are formed or the process would come to a standstill. Brine and recycled mother liquor No. 2 enter the third effect evaporator pan from the evaporator feed storage tanks, see Fig. 5. A steady flow of liquor is removed from the bottom of the No. 3 pan and is pumped through the No. 3 cone of the salt trap, a clear liquor being returned to the NO. 3 pan. A portion of this clear liquor is pumped to the second effect pan. This process is repeated in each pan. The liquor from the No. 2 pan is pumped through the No. 2 salt trap cone and returned to the No. 2 pan.

Jan 1, 1955

By S. K. Basu, H. H. Kellogg

THE physical-chemical behavior of the system Pb-S-0 is of prime importance to the understanding of lead smelting processes, yet little accurate information is available on either equilibrium or kinetic behavior in this system. This paper is the first report of a program designed to fill gaps in our knowledge of this system. In the total ternary Pb-S-0, the region of greatest metallurgical interest is that bounded by the compositions Pb-PbS-PbS0,-PbO-Pb. Systems richer in sulfur, or richer in oxygen,* than those essentially pure SO2. This conclusion follows from the fact that all systems are in a highly reduced state, since either PbS or Pb is a constituent of all the equilibria. The content of 02, SO3, S2, S6, S8, and so forth, can be shown to be negligible compared to SO, in all such systems.* corresponding to this region can only be obtained at gas pressures exceeding 1 atm, a condition seldom met in lead smelting practice. Not only is the present study limited to condensed phases within this portion of the total system, but it is limited to temperatures at which all phases are pure solids, except for lead, which is liquid. In this limited system the following seven condensed phases are known to exist: Pb(l), PbS(c), PbO(c), PbSO,(c), PbSO,•PbO(c), PbSO4 • 2PbO(c), and PbSO, -4PbO(c). PbO exists in two crystal modifications,' but only the high-temperature yellow form is considered here. Schenck and co-workers2-4 reported the compound PbSO4 3Pb0 to be stable at high temperature, but the more recent work of Lander,5 and the present work, prove that the tetra-basic sulfate, rather than the tri-basic sulfate is stable. Fig. 1 shows the composition diagram for the binary PbO-PbSO2, based primarily on the work of Lander. In this study the univariant boundaries and invariant points existing among these seven condensed phases and the gas phase have been determined. In a ternary system, the phase rule indicates that an invariant point involves the simultaneous equilibrium of five phases—four condensed phases and the gas phase. A univariant relation involves four phases—three condensed phases and the gas phase. The gas phase in the systems studied is The following stable univariant equilibria between SOz and the condensed phases were identified: (a) PbS + 7PbS04 = 4(PbSO, - PbO) + 4SO2 (b) PbS + l0(PbS04 • PbO) = 7(PbSO4- 2PbO) + 4SO2 (c) PbS + 8(PbSO4 • 2PbO) = 5(PbSO4 . 4PbO) + 4SO2 (d) Pb + PbSO, • 4PbO = 6PbO + SO2 (e) 3PbS + PbSO4 . 4PbO = 8Pb + 4SO2 (f) 3PbS + 16(PbS04 PbO) = 7(PbSO4 . 4PbO)+ 12SO2 (g) 2PbS + PbSO,2PbO = 5Pb + 3SO2 (h) Pb + 3(PbSO4 . 2PbO) = 2(PbSO,. 4PbO) + SO, Of these eight univariant equilibria, five were measured in this work (a, b, c, d, and g) and the behavior of the other three (e, f, and h) was calculated by thermodynamic analysis of the measured data. Two invariant points were found corresponding to simultaneous equilibria as follows: Point 1: PbS, PbSO4PbO, PbSO4.2PbO, PbSO, - 4PbO, and SO2 Point 2: Pb, PbS, PbSO, . 2PbO, PbSO, - 4PbO, and SO2, From the measurements it was also possible to calculate the thermodynamic properties of the three basic sulfates of lead at 298.16°K. EXPERIMENTAL Apparatus—The experimental method consisted of the measurement of the gas pressure exerted by a given reaction mixture at a given temperature. An iridium crucible was used to contain the reaction mixture. There was no evidence of attack of the iridium,* but after use at high temperature for a week

Jan 1, 1961

By AIME AIME

METALLIC corrosion, which results from the chemical affinity of different metals for non- metallic elements, should be considered from both the kinetic and static viewpoints. From the stand- point of statics the metals may be arranged in the order of their affinity for oxygen, chlorine or any other acid- forming element. They may also be arranged in the order of the magnitude of the heat of combination of their corresponding compounds. It is misleading to talk about some metals as "noble," because these relations are all relative; and the order varies for oxygen, chlorine or whatever the element may be. A third way to arrange the metals is by their solution pressures. These three methods indicate that one metal is better under one set of conditions, but not so good under other conditions. Considering the problem from the standpoint of kinetics, the thing which saves most metals is what may be called the sluggishness of reactions. Using organic substances as an example, we know they will all oxidize, but fortunately they do so rather slowly. An increase in temperature always means an increase in the reaction rate, and preventing corrosion at high temperatures is a greater problem than at low temperatures. A second consideration is to avoid all sub- stances which might provoke catalytic action, and as it is generally impossible to foresee what substances might do this, the thing is to avoid all substances other than the main constituents of the alloys. A third consideration is to avoid local electrolytic action, which again indicates the advisability of avoiding the contact of differing substances.

Jan 1, 1926

By Frank D. Hoyt

BY far the most conspicuous of the Pennsylvania slate districts is that extending from the New Jersey line at the Delaware Water Gap westward almost to the Schuylkill River. This covers parts of three counties in east-central Pennsylvania: Northampton, Lehigh, and Berks. The most important development, both in geographic size and product importance, is in Lehigh and Northampton counties. The greater part of the region is underlain by only one formation-the Martinsburg, consisting of slates, clay slates, and sandy shales, all of the Ordovician period. The slate-bearing Martinsburg formation is underlain by Cambro-Ordovician limestones. Immediately overlying the Martinsburg formation is the Tuscarora quartzite of the Silurian period. The Martinsburg formation itself is divided into three distinct divisions, termed simply: the upper, the middle, and the lower members. Commercial slate has been extracted from all of these members, but the formation of greatest importance is the upper member, representing 2600 ft of the total formation thickness of nearly 11,000 ft. The upper member is commonly referred to as the "soft slate" and consists of three facies: 1) beds of blue-gray, very sandy, almost quartzitic slate, in many places, approximately a medium-coarse sand- stone with calcareous cement; 2) blue-gray sericitic slat-the dominant rock type of this member-with occasional chloritic beds; and 3) dark gray or virtually black, highly carbonaceous beds, referred to locally as "ribbons."

Jan 8, 1958

By Richard V. Hughes, Rudolf J. Pfister

The necessity for getting more water into sands of low permeability in any secondary-recovery water-flood operation in order to recover all the available oil always has been a major problem. In the early days of water-flooding the addition of soda ash and caustic soda to fresh input waters was recommended and tried without success in the Bradford field. The most frequent difficulty was sand plugging. The use of natural and artificial brines often has been suggested for water-flooding, in the belief that laboratory observations of decreasing fresh-water throughput rates in measuring water permeabilities of consolidated sand cores might be partially explained by swelling of clays. A review of available literature bearing on the subject and related laboratory experiments are presented herein, offering an explanation for failure in use of soda ash and caustic soda waters and supporting the recent concept that every water used for input purposes in the secondary recovery of oil should possess such physical and chemical characteristics as to keep the clay content of the producing sands in a permanently flocculated condition. Produced brines meet this requirement. Their use is recommended as a means of increasing intake rates of tight sands and oil recoveries, as a solution to brine-disposal problems, and as a means of conserving a natural resource. Introduction There is a general belief among those engaged in the secondary recovery of oil by water-flooding that one of the most important requirements for the success of any such project is an adequate supply of good, fresh water. Fresh waters have the advantages of being more easily stabilized than salt waters and of being usable about the lease for all purposes. The use of brines for water-flooding never has been given much consideration in the Pennsylvania Grade area. The use of brines in Mid-Continent operations has been considered largely as a substitute for fresh waters, which were economically unobtainable for many operations. Estimated recoveries for some water-drive fields indicate that less of the original oil in place will be left upon abandonment than with the above-average practices used in Pennsylvania Grade water-flood operations. Lower residual oil saturations than 25 pct of the pore space following the water-flooding of Third Bradford sand cores in the laboratory are unusual. In comparison, water-flushed sands surrounding any virgin oil pool are found to be practically devoid of oil. Such lower natural residual oil saturations may be the result of a time factor much longer than economic under artificial water-flood operations, but neither the producer of primary oil nor the producer of oil by secondary recovery can obtain maximum recoveries unless full advantage is taken of all natural forces and

Jan 1, 1947

By Richard V. Hughes, Rudolf J. Pfister

The necessity for getting more water into sands of low permeability in any secondary-recovery water-flood operation in order to recover all the available oil always has been a major problem. In the early days of water-flooding the addition of soda ash and caustic soda to fresh input waters was recommended and tried without success in the Bradford field. The most frequent difficulty was sand plugging. The use of natural and artificial brines often has been suggested for water-flooding, in the belief that laboratory observations of decreasing fresh-water throughput rates in measuring water permeabilities of consolidated sand cores might be partially explained by swelling of clays. A review of available literature bearing on the subject and related laboratory experiments are presented herein, offering an explanation for failure in use of soda ash and caustic soda waters and supporting the recent concept that every water used for input purposes in the secondary recovery of oil should possess such physical and chemical characteristics as to keep the clay content of the producing sands in a permanently flocculated condition. Produced brines meet this requirement. Their use is recommended as a means of increasing intake rates of tight sands and oil recoveries, as a solution to brine-disposal problems, and as a means of conserving a natural resource. Introduction There is a general belief among those engaged in the secondary recovery of oil by water-flooding that one of the most important requirements for the success of any such project is an adequate supply of good, fresh water. Fresh waters have the advantages of being more easily stabilized than salt waters and of being usable about the lease for all purposes. The use of brines for water-flooding never has been given much consideration in the Pennsylvania Grade area. The use of brines in Mid-Continent operations has been considered largely as a substitute for fresh waters, which were economically unobtainable for many operations. Estimated recoveries for some water-drive fields indicate that less of the original oil in place will be left upon abandonment than with the above-average practices used in Pennsylvania Grade water-flood operations. Lower residual oil saturations than 25 pct of the pore space following the water-flooding of Third Bradford sand cores in the laboratory are unusual. In comparison, water-flushed sands surrounding any virgin oil pool are found to be practically devoid of oil. Such lower natural residual oil saturations may be the result of a time factor much longer than economic under artificial water-flood operations, but neither the producer of primary oil nor the producer of oil by secondary recovery can obtain maximum recoveries unless full advantage is taken of all natural forces and

Jan 1, 1947

After the explosion in the Black Heath pit, that company sent to England for some experienced miners to reopen the mine. The results of their work in this vicinity are mentioned in an advertisement for pit hands by the Mid-Lothian Co., as follows: "PIT HANDS WANTED.-In consequence of reports having been circulated of the insecurity of hirelings in the Mid-Lothian Mines, the Company deem it proper to make known, that the mines have recently been opened, and that not the slightest explosion from gas has occurred; the workings were laid out and are now progressing, ° under a plan furnished by Messieurs Foster & Hall, .two distinguished English Colliers, sent over from England to reclaim the Pits of the Black Heath Company after the recent explosion of gas-and the present under ground operations are now conducted under the management of one of the English foremen left here by these gentlemen, and supervised by Mr. Wm. Hall, who has under his superintendence the Black Heath Company's Works at present. The skill and capacity of those gentlemen, is fully evinced in their skilful reclamation of the Black Heath Mines, and their present successful working of said Pits; and their confidence in the safety of the hands in the Mid-Lothian Mines, will be seen, by reference to the annexed extract from the Plan left by Messrs. Foster & Hall for laying out and working the Mid-Lothian Mines, and from the Certificate of Mr. William Hall, as to the manner in which that plan is carried into effect. This publication has been deemed proper, as the Company are now in want of some ten or fifteen additional able-bodied, active Pit-hands, on hire by the year, for which they will give the most liberal hire. The Company have not hitherto spared any labor or expense, deemed necessary to secure the absolute safety and comfort of the hands in their mines; nor is it designed in future to omit any thing that can add to the security of their own hands, or the hired laborers of other persons-indeed they can, with great propriety, say, as far as they have progressed, that no mines in this country exhibit stronger, if as strong, evidence of general safety. The Company will receive on hire, no hands who do not voluntarily enter their service -and they request of those having hands to hire out, to remember that they will want upon hire, successively, at intervals of every ninety days, some additional four or five hirelings during the year, or to purchase, progressively, that number of healthy, able-bodied young men. "Owners of slaves at a distance from the Coal Mines, would do well to give some attention to the subject. There is no place in this country where slave labor commands as much, where their general health is better, and where the treatment and contentment of the slaves are surpassed. It is true that within the last few years several disastrous accidents have occurred, but from the scientific and practical skill attracted to the mines, these accidents will be of rare occurrence, it is to be hoped. A. S. WOOLDRIDGE, President, at the Mines in Chesterfield County.

Jan 1, 1942

By C. F. Jr. Nagel

THIS paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. HEAT TREATING Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this improvement may be illustrated by the typical properties of duralumin (Table 1). It is essential that the material be in the wrought condition in order to obtain maximum heat-treatment effects.

Jan 1, 1927

By Frank Miller

THE lower cost of producing oil from naturally flowing wells compared with pro-duction costs accruing from artificial lifting methods has stimulated much research, with the joint purpose of extending the natural flowing life of wells and of increas-ing the productivity of small wells. The laboratory investigation described herein was made to determine the effect of a slotted liner on the pressure gradient in the vicinity of the wall of a flowing well. Flow restrictions caused by the liner induce energy losses between the oil-bearing for-mation and the inside of the liner, which may be reduced by improved liner design, and thereby the flow capacity of wells may be increased. These losses have been evalu-ated for rectangular slots of different sizes, and means are suggested for reducing them. The dearth of information concerning the nature of the flow of fluids from uncon-solidated sands through small openings in the walls of pipes-as represented by the flow of oil from an oil sand into a slotted liner-is acknowledged. Although the bene-fits to be realized by operators through the use of optimum liners is just beginning to be recognized generally, Coberly1 in 1937 pointed out that the functioning of screen casing is an important factor in the pro-duction of oil. From his study on the selection of size of oil strings for wells in California, Parks2 concluded, in part, that the perforated section of the oil string de-serves continued study, especially with respect to the selection of perforations. The growing use of gravel packing result-ing from certain research findings lends even more significance to the problem of selecting optimum liners, as the application of these methods usually requires slotted liners or other kinds of perforated liners. The present study was made to obtain further information for the guidance of engineers and operators in selecting slotted liners and to develop a laboratory method that may be used in analyzing possible pressure conditions surrounding most types of perforated casings used in producing oil wells, so that the present inadequate fund of knowledge on this important subject may be expanded.

Jan 1, 1940

By Donald W. Petrasek

The effects of selected alloying elements on the elevated-temperature tensile properties of copper alloy -tungsten fiber reinforced composites were invcstigated. A cornparison of the elevated-temperature tensile properties of copper alloy - tungsten fiber reinforced composites, representing soluble systems. was made with copper - tungsten fiber reinforced composites, representing a mutually insoluble system. A linear relation between tensile strength and volume percent fiber content existed at elevated temperatures for all the systenzs investigated. The copper alloy composites were weaker in tension at high volume percent fiber contents than copper composites in which alloying with the fiber did not occur. The tensile strength of the alloyed tungsten fiber decreased with increasing penetration of the alloying element into Ihe tungsten fiber. THE technique of combining strong fibers with relatively weak matrix materials so that the fibers are load-carrying members has been utilized for many years in the reinforcement of plastics with glass fibers. This type of strengthening is currently being extended to include the reinforcement of metals with metallic fibers. Investigations of the room-temperature tensile properties of metal-fiber-reinforced metallic composites have been numerous,'-" but the study of tensile properties at elevated temperatures has been limited. In previous work done at the Lewis Research Center' composites consisting of mutually insoluble constituents were investigated. Composites were made of copper reinforced with uniaxially oriented tungsten fibers. The stress-strain behavior and tensile properties of the composites were related to the tensile properties of the base materials. The tensile strength of the composite was directly proportional to the volume percent of tungsten fiber present, and the full strength of the fiber was realized. Few metal fiber - metal matrix systems exist that are mutually insoluble, and those that do exist are not generally practical. An extension of this work was an

Jan 1, 1967

By I. N. Zavarine

The observations presented in this paper were recorded during a study of the spheroidizing process. Spheroidization of cementite in steel is either brought about to develop a set of desirable mechanical properties or is an incidental result of mechanical and heat-treating manipulations. Physical properties of steel are materially influenced by the state of the cementite. Conversion of cementite from the lamellar to the spheroidal state is usually accompanied by a decrease of hardness and of strength and by an increase in ductility. The spheroidized structure is usually considered as an ultimate step in the process of the softening of steel. The unorthodox hardening of a 3.5 per cent Ni steel (SAE No. 2330) after a heat-treatment that previously proved entirely suitable for a complete spheroidization of cementite in carbon steels led to the observations that constitute the subject of the present paper. Experimental Procedure The steels used for the experiments described were bought on the market. All were in the form of 3/4-in. round bars. Their chemical compositions are given in Table 1. The spheroidization of cementite in steels can be obtained in several ways. The method used in the present work is, perhaps, the least known. It consists of cyclic heating and cooling of steel, the temperature being

Jan 1, 1939

By I. N. Zavarine

The observations presented in this paper were recorded during a study of the spheroidizing process. Spheroidization of cementite in steel is either brought about to develop a set of desirable mechanical properties or is an incidental result of mechanical and heat-treating manipulations. Physical properties of steel are materially influenced by the state of the cementite. Conversion of cementite from the lamellar to the spheroidal state is usually accompanied by a decrease of hardness and of strength and by an increase in ductility. The spheroidized structure is usually considered as an ultimate step in the process of the softening of steel. The unorthodox hardening of a 3.5 per cent Ni steel (SAE No. 2330) after a heat-treatment that previously proved entirely suitable for a complete spheroidization of cementite in carbon steels led to the observations that constitute the subject of the present paper. Experimental Procedure The steels used for the experiments described were bought on the market. All were in the form of 3/4-in. round bars. Their chemical compositions are given in Table 1. The spheroidization of cementite in steels can be obtained in several ways. The method used in the present work is, perhaps, the least known. It consists of cyclic heating and cooling of steel, the temperature being

Jan 1, 1939

By L. K. Jetter, J. C. Ogle, C. L. McHargue

The preferred orientation developed in extruded aluminum rods has been studied as a function of extrusion temperature, extrusion speed, and position in the rod. Duplex <111> - <001> textures were developed for slow extrusion speeds at temperatures of 75° to 850° F and for fast extrusion speeds at temperatures of 75° to 450°F. The <001> texture component was shown to be primarily due to re crystallization occurring during fabrication. At fast speeds and billet temperatures of 650° to 850°F, complete recrystallization occurred and <115>or<118> textures were found. The nature of the structure has proved to be an important variable in the production and use of extruded products. Data on the flow of aluminum and aluminum alloys summarized by Smith,&apos; Hardy,&apos; and Locke3 show that the extruded product may possess a deformed, a partially recrystallized, or a completely recrystallized structure, and there may be important variations in the structure from surface to center and from front end to back end of an extrusion. This inhomogeneity in grain structure and preferred orientation affects both the mechanical properties of the extruded section and its response to subsequent heat treatment. Among the fabrication variables causing these differences are temperature, extrusion ratio, and extrusion speed. Preferred orientation which develops during the extrusion of rods is of the fiber-type and, in general, has been assumed to be similar to that developed in rods or wires fabricated by drawing through dies, rolling, or swaging.4 Because of the nature of the flow of metal being extruded, this assumption may be valid for material near the center of the rod but probably is not valid for the outer layers. In most face-centered-cubic metals a duplex fiber texture has commonly been reported in which the grains have either <Ill> or <001> directions parallel to the longitudinal axis. Sachs and fichiebold5 reported cold-drawn aluminum (99.6 pct pure) to have a single <Ill> fiber texture, and this observation was confirmed by Schmid and Wassermann.6 Hibbard, on the other hand, observed a minor <001> and a major <111> texture in 99.994 pct A1 cold drawn to 98 pct reduction in diam.7 He concluded that the <001> component resulted from a small amount of room-temperature recrystallization. Dayal8 concluded that the <001> component was an intermediate component which disappeared at high reductions in 99.5 pct pure Al. Kostron and schippers9 found duplex <111> — <001> textures in extruded 99.5 pct Al, as did Gow and cahnl0 and GOW11 for extruded rods of commercial and superpure aluminum. Similar duplex fiber textures have been reported for aluminum alloys by Kostron,= Unckel,13 and Van Horn.14 The present paper is concerned with the variation in texture with fabricating conditions and with the nature of the texture components in extruded aluminum rod (99.99 pct pure). EXPERIMENTAL PROCEDURE Ingots were chill-cast in cast-iron molds and machined to 3-in. diam by 6-in. long extrusion billets. These billets were upset to 3.125 in. diam and extruded through a flat-face 0.690-in. diam die. Quenching of the rods was accomplished by a water spray at the die face. The combinations of fabricat-

Jan 1, 1960

By A. G. Guy, T. B. Lindemer

A second intepation of the Fick law has been developed and applied to three-place data generated from the Gosting and Fujita solution of the diffusion equation. This integration provides new mathematical techniques for the analysis of experimental data. Through use of the synthetic data it is shown that for concentration-independent interdifiusion coefficients these techniques permit a more accurate determination of the coefficients than does the usual Boltzmann-Alatano analysis. Another technique, applicable to the most general concentration-dependent diffusion coefficients , can be used to determine whether given sets of coefficients are consistent with the experimental ternary concentration-distance curves. DURING the past 10 years the subject of three-component diffusion has advanced from the stage of a laboratory curiosity to the status of an accepted portion of physical metallurgy.1 In the course of this development the underlying treatment for two-component sys- tems was extended and generalized to accommodate the added component, but fundamentally the analyses currently employed for ternary systems are analogous to those previously developed for binary systems. There are several indications that an improved analysis is needed for the ternary case. First, the two cross coefficients, D312 and D321 are typically an order of magnitude smaller than the direct coefficients and consequently are difficult to determine with adequate precision. Second, instead of a single concentration-penetration curve (as in binary diffusion), there are four such curves in the usual determination of ternary diffusion coefficients. These curves have definite theoretical interrelationships, but actual experimental curves exhibit significant departures from these relationships. Finally, the amount of data needed to adequately describe the diffusion behavior of a ternary system is so large that radically new methods are needed to facilitate the gathering of these data. ICirkaldy2j4 has proposed several possible analyses of ternary diffusion data, including some of the methods in current use. A "second-integration" procedure proposed by him4 differed in important respects from that presented here and was not carried to the point of application. Two other methods have been explored by the authors and will be published separately; these are a numerical analysis technique and a method for the analysis of a single ternary diffusion couple. Still other analyses are being explored by various investigators. At present it seems likely that the final analysis of ternary diffusion that evolves will be a composite

Jan 1, 1968

By L. W. Eastwood

The structure of eutectics has been studied by a number of investigators, and the complexity of the structural relationship of the components has been agreed upon, especially that of the "eutectic colony," type III of Portevin&apos;s1 classification. This paper does not attempt to alter the present classifications of eutectics; rather, it discusses the relationship between the macrostructure and the microstructure of the copper-cuprous oxide eutectic, and describes in detail the mechanism of the formation and the structure of the eutectic. Further, throughout the entire discussion it attempts to point out certain misconceptions in regard to the interpretation of the observed structure of the copper-cuprous oxide eutectic, one of the so-called "eutectic colony" types, and to correlate as much as possible the work done by the writer with that done by other investigators. Of the three types of eutectics listed by Portevin,2 the eutectic colony type has presented the greatest difficulty in interpretation. Although the copper-cuprous oxide eutectic is typical of the eutectic colony type in appearance, it may not be truly representative because the copper forms about 96 per cent of the eutectic and the cuprous oxide about 4 per cent. The interpretation of the origin and structure of the "eutectic colony" given here is strictly limited, therefore, to the copper-cuprous oxide eutectic. Macrostructure Fig. 1 shows the macrostructure of the eutectic at 3 diameters, the melt having been chill-cast into an iron mold, the resulting specimen sawed into two parts and the section polished and etched with the usual mixture of hydrogen peroxide and ammonium hydroxide. This specimen contains 0.48 per cent oxygen and is only slightly hypereutectic. If such a melt is allowed to cool slowly, large macrograins will form without the columnar structure of Fig. 1 and the well-known phenomenon of liquation will occur, forming copper oxide dendrites at the top and copper

Jan 1, 1934

By W. R. Bull, J. R. Roos

A method is described whereby the true financial value of each constituent of each concentrate can be calculated. Each value is then compared with what this value would be in a perfect separation. The difference in each case represents the loss incurred by each aspect of an inefficient separation. The relative magnitudes of these losses indicate those avenues of plant investigation and research that offer the highest potential reward. The metallurgical efficiency of a concentration operation is difficult to express because there are two criteria of performance, namely, grade and recovery. Neither of these alone gives any indication of the effectiveness of an operation and, if they are combined in some formula, it must be empirical and unreliable because of many external factors. Since milling is an operation performed as one step in the most profitable overall method of producing a metal or other end product, the main objective of mill operation should be to make a maximum contribution to this maximum profit. When concentrates are sold to custom smelters, the income from the operation, and the costs, may be calculated. When concentrates are further processed by another division of the same company, and there is no formal financial relationship between, say, the milling and smelting divisions of the company, the mill superintendent&apos;s job is less well defined. But even so, if the mill superintendent works as though he were selling his concentrates, and uses reasonable, if fictitious, conditions of sale, then he can get a good indication of the effectiveness of his operation by calculating his "Economic Recovery". ECONOMIC RECOVERY This is a method used as a basis of operation by several mills and has been described in the literature. Very briefly, the "standard" of operation is taken as that of a mill separating the ore into perfectly pure concentrates with 100% recovery of each mineral in its respective concentrate. For example, a 4%Pb, 4% Zn ore (galena and sphalerite), would provide a lead concentrate weighing 4.62% of the feed and assaying 86.6% Pb and a zinc concentrate weighing 5.97% of the feed and assaying 67.1 % zinc. These perfect concentrates are (hypothetically) shipped to the appropriate smelters, freight and treatment charges and payments calculated, and the net return obtained. This is the optimum financial return for the operation of the mill and is used as the standard. Now the return for the actual, real-life, mill operation is calculated in the same way, and the ratio of the two is termed the Economic Recovery. Many additions and modifications may be made in any particular case. For example, if the zinc mineral is marmatite, the optimum grade of the zinc concentrate may be set lower than 67.1%. If silver is present, it will be recovered 100% in the lead concentrate in the perfect operation. Similarly, cadmium will be recovered 100% with the sphalerite. Mr. Weiss&apos; paper&apos; mentions a case where, because of extremely fine intergrowth between the valuable mineral, chalcocite, and pyrite, the optimum grade of copper concentrate was taken as 45% Cu instead of the theoretical 80%. Each operation will present its own possibilities in this way.

Jan 1, 1970

By Claudio Guarnaschelli

Alteration of the electronic distribution of mineral surfaces by light irradiation has been used to modify the adsorption characteristics of flotation reagents. Energy of a few electron volts is suficient to cause the necessary transitions that either enhance or retard the adsorption phenomenon. The adsorption characteristics of potassium ethyl xanthate on galena and marmatite are presented as functions of the energy of illumination, type of semiconductor, and surface oxidation. In dilute solutions, the adsorption differences are readily detected by controlled kinetic measurements. The correlation between the electronic distribution and the adsorption and desorption phenomena at the solid surface is gaining more attention and acceptance. These interrelations have found a practical application in mineral processing since all of the sulfide minerals display semiconducting properties. By varying the ratio of free electron to electron vacancies, the separation of ilmenite from rutilel and zircon from pyrochlore" has been executed successfully. Plaksin et al.&apos; indicate three possible ways of utilizing the semiconductor properties of a mineral. The first one involves the control of the oxidation-reduction potential of the liquid phase, the second one consists of allowing selected additives to diffuse through the mineral surface, while the third one entails a change in the adsorption and chemical activity of minerals by irradiating their surface. The aim of the present work is to consider the effect of irradiation on the adsorption-desorption characteristics of natural minerals. Since the effect of irradiation is to change the electronic distribution at the surface:

Jan 1, 1971

By William Fink

THE constitution of the aluminum-cobalt alloys has been the subject of relatively few investigations. Brunck1 analyzed the residue which remained after treating the 17 per cent cobalt alloy with dilute hydrochloric acid. The results of the analyses indicated the existence of a compound Co3Al13. Guillet2 published a liquidus for the aluminum-cobalt system which contained two maxima corresponding to CoAl6 and CoAl2 and two eutectic points at 30 and 74 per cent Co. The most extensive investigation of the system was carried out by Gwyer,3 whose results are summarized in Fig. 1. It will be noted that at the aluminum end there is a suppressed eutectic at 644° C. By extrapolation of the duration of the eutectic arrest to zero, the composition of the compound was placed at Co3Al13. Another thermal arrest was noted at 550° C., which Gwyer attributed to a peritectic reaction. The present investigation of the aluminum end of the aluminum-cobalt system is the eleventh of a series dealing with the constitution of aluminum; rich alloys prepared from electrolytically refined aluminum.4 Preparation of Alloys.-The alloys used in this work were all prepared from electrolytically refined aluminum, the analysis of which is shown in Table 1. In preparing some of the alloys, metallic cobalt (98 to 99 per cent) was used either directly or in the form of an intermediate alloy, the composition of which is given in Table 1. In order to obtain alloys of higher purity, cobalt was introduced into some of the alloys by means of chemically pure cobaltous chloride which was readily reduced by the aluminum. A small electric furnace with nickel-chromium heating elements was used in the preparation of the alloys.

Jan 1, 1932

By J. O. Betterton, D. S. Easton

A detailed investigation was made of the phase diagram of silver-zirconium, particularly in the region 0 to 36 at. pct Ag. The system was found to be characterized by two intermediate phases Zr2Ag and ZrAg and a eutectoid reaction in which the -zirconium solid solution decomposes into a-zirconium and Zr2Ag. It was found that impurities in the range 0.05 pct from the iodide-type zirconium were sufficient to introduce deviations from binary behavior, and that with partial removal of these impurities an increase in the a-phase solid solubility limit from 0.1 to 1.1 at. pct Ag was observed. The phase diagram of the silver-zirconium system is of interest as an example of alloying a transition metal from the left side of the Periodic Table with a Group IB element. Silver would normally act as a univalent metal, its filled 4d-shell remaining undisturbed during the alloying. However, there is a possibility that some of the 4d electrons might transfer to the zirconium. An insight into such a question can occasionally be obtained by comparison of phase diagrams. The silver-zirconium system forms part of a more complete review of various solutes in zirconium in which these valency effects were studied.&apos; Earlier work on the silver-zirconium system was done by Raub and Enge1,2 who investigated the silver-rich alloys. After the start of the present experhents, work on this system was reported by Kemper3 and by Karlsson4 which for the most part agrees with the phase diagram presented here. EXPERIMENTAL PROCEDURE The alloys were prepared by arc casting on a water-cooled, copper hearth with a tungsten electrode and in a pure argon atmosphere. Uniform solute composition was attained by multiple melting on alternate sides of the same ingot. Progressive improvements in the vacuum conditions inside the apparatus during the course of the experiments reduced the Vickers hardness increase of the pure zirconium control ingot from 10 to 20 points, observed initially, to negligible amounts at the end of the experiments. Such hardness changes in zirconium are a well known indication of purity. For example, -01 wt pct additions of oxygen, nitrogen, and carbon increase hardness by 6, 10, and 3 VPN respectively. &apos;9&apos; Further verification that the final casting technique did not add a significant quantity of impurities was obtained when pure zirconium was arc cast and then isothermally annealed in the vicinity of the allotropic transition. The transition was always observed to take place over the same temperature range as in the original crystal bar. The alloy ingots were annealed in sealed silica capsules for times and temperatures which varied between 1 day at 1300°C and 60 days at 700°C. The best method found to prevent the reaction of the zirconium with the silica was foil wrapping of molybdenum or tantalum. With this method, samples of pure zirconium were found to be unchanged in hardness after annealing for 3 days at 1200°C. In most of the experiments the protection of these foils was supplemented by an additional layer of zirconium foil inside the molybdenum or tantalum foil. The alloys, foil, and the capsule were outgassed at pressures in the range 10 to l0-7mm Hg in the temperature range 800" to 1100°C before each anneal in order to remove hydrogen and other impurities, and to provide a suitable container for the high purity, inert atmosphere, which is essential in the annealing of zirconium. The temperature measurements were made with Pt/Pt + 10 pct Rh thermocouples calibrated frequently during the experiments against the melting points of zinc, aluminum, silver, gold, and palladium. For the longer anneals the sum of various temperature errors was generally well within ± 2°C. For short-time anneals and during thermal analysis the overall temperature error is considered to be within ± 0.5°C. The compositions of the alloys from the quenching experiments were determined by chemical analysis at Johnson Matthey and Company, Ltd., under the direction of Mr. F. M. Lever. The actual metallo-graphic samples were individually analyzed in every case, and prior to the analyses two or more sides of each specimen were examined to insure that the specimen was not segregated. The sum of the solute and solvent analyses was in each case within the range 99.9 to 100.1 pct. In the course of the experiments, minor impurities in the range 0 to 500 ppm were found to have significant effects on the zirconium-rich portion of the phase diagram. Similar effects had been encountered previously in other zirconium phase-

Jan 1, 1959

By J. J. Jakosky

ALL electrical geophysical methods depend for their operation upon the effects produced by the flow of an electric current. By studying these effects it is possible to predict the general axis of current flow. The greater flow of current is in the path of greatest, effective conductivity; and since the effective conductivity of a mineralized zone is different from that of its surrounding envelope (usually much greater), it is possible to locate such a mineralized zone by the distribution of current. Due consideration must be given, of course, to geological structure, to type of mineralization, and to other factors. A number of methods are used to cause this flow of current, and various methods are available for detecting the presence of such current flow and for studying its effects. In a rather detailed way, this paper will discuss the theoretical and practical phases of the inductive methods of geophysical prospecting. ELECTROMAGNETIC GENERATION OF AN ELECTROMOTIVE FORCE The inductive method is so named because the current flowing in the conductor is obtained by electromagnetic induction, instead of by the use of ground electrodes through which a current is passed as in the applied potential systems, or by direct contact with the orebody. An alternating current flowing in a coil will create an electromagnetic field around the coil. This field will have the same frequency as the current and will radiate or travel outward from the coil in closed magnetic or flux circuits: These flux circuits (in air or a homogeneous medium) will be perpendicular to the plane of the coil and will extend or travel outward with uniform velocity in every direction. Maximum field exists in the plane of the coil. Such a coil used for transmitting or as the "energizer" will exhibit similar figure-eight characteristics to those exhibited by the direction-finding coil which will be described in detail later.

Jan 1, 1928