Search Documents

By H. H. Kellogg

A model of the slag-fuming process for recovery of zinc oxide fume from lead blast furnace slags, adapted to solution by a digital computer, is presented. The model incorporates the variaticm with time of the following: the fuming of zinc and lead, the change in the ferrous-ferric ratio in the slag, the transfer of sulfur to and from the slag, the temperature of the liquid slag, the temperature of the gases and fume which exit to the flue, the heat losses to the water jackets, and the amount of frozen slag on the water jackets. The assumptions which underlie the model-some of which are but crude approximations—are discussed. Despite some obvious shortcomings, the model simulates faithfully many of the important features of practical slag-fuming operations. The behavior of the model is compared with the operation of the American Smelting and Refining Co. fumzace at El Paso, Tex. The model is used to predict the effects on performance of changes in the coal rate, the temperature of the secondary air, and the composition of the coal. THE fuming of lead blast furnace slag for recovery of zinc oxide is standard practice today, and it has been the subject of several previous attempts at mathematical process analysis.'-' The mathematical process model described in this paper incorporates many of the features from the earlier studies, but it is a far more complete and realistic representation of the commercial process in that the following additional features have been included: the fuming of lead as well as zinc; the transfer of sulfur between slag and gas; the addition of slag feed in batches, over a period of time; tapping of the final slag over a period of time; the change of slag temperature with time. The additional features of the present model add greatly to the mathematical complexity, but this difficulty has been obviated by programming the model for solution by a digital computer. The IBM 7094 computer solves the model for one operating cycle of the fuming furnace in less than 1 min. It is doubtful if the same calculations could be completed with the aid of a desk calculator in less than a month. The computer program, written in the Fortran IV language, is too lengthy for presentation here.* Instead, this paper As shown in the sections which follow, it does simulate with remarkable faithfulness most of the known behavior of the industrial process. On the other hand, the model contains several gross simplifications of both the chemistry and heat balance, necessitated by the lack of more exact knowledge. In addition to these known weaknesses, it is not unlikely that those more intimately acquainted with industrial practice than the author will find other additions to or modifications of the model which will improve its utility and reliability. CHEMISTRY In brief outline, the present model treats the fuming furnace as two units, A and B, in series. In A the batch of slag reacts with the continuous stream of air (primary and secondary) and fuel injected at the tuyeres, to produce a stream of hot, reduced gases containing zinc vapor. The zinc content of both the slag and the product gas changes with time because of the batch nature of the process. Unit A is called the "lower furnace" in this paper; physically, it is considered to be that part of the fuming furnace which lies below the charge port. In B, the "upper furnace", the product gas from A is burned with the stream of "tertiary" air, to produce zinc oxide fume. The performance of B also depends on time because of the time dependence inherited from the product gas of A. The rate behavior in the lower furnace determines the important features of the process—the rate of elimination of zinc and lead from the slag, and the amount of fuel required for this purpose. Bell, Turner, and peters' published the first useful model of the lower furnace. They employed the assumption that, at any instant of time, the slag and reduced gas reach a state of equilibrium, according to the reactions: They cited only indirect evidence in support of their assumption of slag-gas equilibrium, yet several more recent laboratory studies of the activity of zinc oxide in slags4-8 have produced evidence which supports their view. On first acquaintance it seems unlikely that a high-output "rate" process like slag fuming would even approach an equilibrium state. The author, in an earlier study,' established, however, that the gas-slag interface in a fuming furnace was capable of such high mass-transfer rates that a close approach to equilibrium between gas and slag was quite probable. In devising the present model it was decided to assume a state of equilibrium between slag and gas at the outset, and then to modify this assumption as necessary in order to make the model agree with the be -havior of the actual process. Up to this time the assumption remains a part of the model, since no behavior

Jan 1, 1968

By George W. Riter

(Canal zone meeting, November, 1910.) A DISTINGUISHED engineer, the active head of a large mining company, has said that surveying attains the dignity of a profession only in the hands of a few men-the few who know how to keep notes that will be understood by even a novice without further word of explanation. Of all mine-records, survey notes are perhaps the most important. The maps made from them serve as a working-guide, and as framework for other data ; and when, from any cause, access to underground workings is shut off, the surveyor's record often becomes invaluable. So seldom does a surveyor have a chance to check underground surveys by making a closure, that he is compelled to rely on the precision of each step of his work for the accuracy of the final result. When data are fully recorded on the spot, the notes, even in the hands of second parties, become evidence of the care and precision with which the surveying was done. It is worth a great deal to be able to pick up the work of a former surveyor where it was left o$; and to be able to carry it forward without retracing from the beginning. The purpose of this paper is to describe the survey-note system of a mine now under my direction, in which underground surveys had to be relied upon entirely for the proper division of rich ore-bodies between neighbors, thereby placing a premium on accurate surveying and permanent records. In survey-work, it soon turns out that paper is the least item of expense, and that little is gained by trying to economize note-book space. For many purposes it is best to record notes on cards or loose-leaves, which may be left in the office at the end of the day's work, and need not be carried into the mine again, there to become smeared with grime and grease. With the loose-leaf or card system, all notes relating to the same local-

Apr 1, 1911

By Charles H. White

Discussion of the paper of A. L. Sweetser, Tress., xxxviii., 236. CHARLES H. WHITE, Harvard University, Cambridge, Mass. (communication to the Secretary*) :-Those interested in leaching-processes gladly welcome contributions on either laboratory-tests, such as are reported by Mr. Sweetser, or mill-tests made on larger quantities of ore; and especially valuable are such reports, even with negative results, if the methods adopted are the outgrowth of an intimate knowledge of the conditions to be met. It seems very desirable, therefore, that as complete details as possible be given in reporting on such tests, particularly with respect to the character of the ore under examination. The questions of prime importance in the sampling of ore and in the making up of charges for laboratory-tests are those respecting its grade and uniformity. In Mr. Sweetser's paper the first of these questions is answered definitely, but the answer to the second, although apparent on inspection of the results, might be more strongly emphasized with advantage, since it is only on account of the extreme uniformity of the ore that the satisfactory results obtained could have been expected. It seems advisable to call attention to the fact that for average ores, and more particularly for uneven, or 11 spotted ores, the quantities used by Mr. Sweetser are not usually regarded as sufficient to insure satisfactory results. Let us examine the method somewhat in detail. The ore was crushed to pass a 5-mesh screen, and a sample of 45 lb. was taken out for assay and tests. The diameter of the largest grain of this ore, according to Richards,1 was 2.67 mm.-assuming here, as in the following cases, that the wire of the screen was of the largest size used for the purpose, thereby giving any possible advantage in this respect in favor of the method. The table in Richards's book, p. 852, shows that 45 lb. is a sufficient quantity for a fair sample with uniform ores, but not sufficient

Jan 7, 1908

By C. W. Dunham

FROM the primary gyratory crushing plant, described in MacLeod's article, ore is delivered to a large storage or surge bin from which it is carried by two transverse conveyors to the secondary crushing plant. The bin has a useful drawoff of about 13,000 tons, this being slightly over one half of the initial daily capacity of the Morenci Reduction Works. This arrangement provides sufficient storage to permit intermittent operation of the primary and secondary crushing plants without too close a coordination between the two.

Jan 1, 1942

By Louis V. Bender

THIS paper gives a short review of the installation for and the use of gas, as a. fuel, at the Anaconda Reduction Works of the Anaconda Copper Mining Co. Before putting in gas tile fuels used were pulverized coal, lump coal, coke distillate and oil. These fuels are now almost entirely eliminated. For nearly fifty years bituminous coals from Wyoming and Montana fields had been used. These coals were of a good grade, analyzing 11,300 B.t.u. and having an ash content of 12 per cent. When hydro-electric power replaced steam-driven equipment, the coal requirements were reduced; and, on account of improvements in metallurgy and/ or in furnace design, the quantity was lessened. Later, oil and distillate were introduced and used in some of the operations. All of these things tended toward the lessening of the amount of coal used, and had it not been for the increase in the size of the plant, the tonnage used would have been small when the change was made to gas.

Jan 1, 1932

By AIME AIME

POSSIBILITY of a greatly increased manganese production from domestic source; is indicated by news that the Bureau of Mines has been successful in producing concentrates with high manganese content from the low-grade deposit, in the Las Vegas, Nev.) area. The first unit of the comprehensive group of pilot plants built by the Bureau of Mines at Boulder City, Nev., under a defense appropriation has started operations, demonstrating definitely the applicability of a process developed in the Bureau laboratories. About 12 1/2 lb. of manganese is needed for the production of every ton of steel, and substitution is difficult. The United States produces only about 3 per cent of its total needs of this ore. Only high-grade ore, such as the Russian ore, containing 18 per cent or more manganese, is generally used by American producers in making ferro¬manganese the form in which manganese is usually added in steel manu-

Jan 1, 1941

By AIME AIME

THE papers presented at the geophysics session" on Feb. 17 were concerned largely with three aspects of the science. The first ones dealt with the transmission of elastic waves through the earth, then electrical methods came in for their share of attention and finally, the question of the teaching of geo- physics came up for the first time at these meetings. Also, for the first time, there was a symposium of mining men on the practical value of the new science. The paper (T. P. 267) entitled "Seismic Propagation Paths" was presented by Donald C. Barton in the absence of the authors. It dealt with an investigation of the speed of propagation of seismic waves. The latter travel in a straight line when proceeding at a constant velocity, but if the velocity increases at increasing depths, the line of travel becomes a curve. Under the assumption of the authors this curve is found to be the arc of a circle, and their paper gives calculations for reflected and refracted wave paths under these circumstances.

Jan 1, 1930

By Augustus Locke

The paper has two parts: the field argument and the microscopic argument. The field argument indicates that either the deep chalcocite has replacea sulfide of extraordinarily easy replaceability or it is hypogene. The microscopic argumentindicates that this sulfide, if it existed, must have been hypogene bornite; that this bornite must so excel known bornite in replaceability as to constitute a new variety; that the existence of this new variety is wholly unsupported by evidence; and that the deep Butte chalcocite is therefore hypogene. IN 1900, when the public first heard of "secondary enrichment" the Butte chalcocite seemed clearly supergene. Mining, through successive regions of leached capping, bonanza sulfide, and sulfide less rich, had paused at lean bottom levels which, though chalcocite-bearing, suggested the waning of copper. The deepest chalcocite, at 1500 ft., was yet too shallow to disturb the supergene hypothesis. But, with deeper mining, lean levels yielded to fat ones. Here and there they showed, within the same vein, an inverted distribution, chalcopyrite above and chalcocite below. To the miners' astonishment, they carried chalcocite, unaffected by cross faults, on an independent course to the depth of 2500 ft. The pattern of ore distribution, hitherto revealed only in fragments, was now appearing in perspective, and, in the depth of the chalcocite, was beginning to make Butte differ from all districts where the chalcocite is indubitably supergene. The idea of hypogene origin at length came into favor; by 1913, when Sales1 advocated this origin, the argument had become a powerful one. This argument rested on field evidence; but, already, there was beginning to emerge microscopic evidence not included in this arugment. Especially pertinent was the proof that (1) The deep chalcocite lies in-mixed with bornite, often microscopic; (2) the deep chalcocite often replaces bornite; and (3) replacement of bornite by chalcocite is accom-

Jan 3, 1924

By Blamey Stevens

(San Francisco Meeting, October, 1911.) IN this paper, which is a logical extension of my paper, The Laws of Intrusion, 1 the various pressures of emanation and their mechanical causes and effects on the large scale of nature are determined, .and a classification of emanations is deduced therefrom. The Subterranean Sea. The subterranean sea is here defined as the intercommunicating water contained in the trains of pores and fissures of the rocks down to great depths. Whether the actual amount of water constituting this subterranean sea be large or small, does not enter into the present argument, since the static pressure of this water at any particular depth is not a function of the quantity : it involves only the depth and the density of the water. Densities. The total pressure at depths down to 10 or 15 miles is made up of the rock-stresses investigated in my previous papers, and the pressure of the subterranean sea. The latter component must evidently be equal to the weight of a solid column of the overlying water of unit sectional area. As water expands with heat, it should really be necessary to sum the density at every level. A knowledge of the densities of water under a variety of conditions is therefore needed, but does not seem ever to have been ascertained for such combined pressures and temperatures as we have to consider. The specific gravity of water at 28° C. for various pressures up to 400 atmospheres, has been determined by Barus,2 who

Apr 1, 1912

By W. B. Price

AT the New York meeting of the American Institute of Mining and Metallurgical Engineers held in February, 1926, W. H. Bassett and J. C. Bradley presented a paper entitled "Exudations on Copper Castings."' The purpose of the present paper, as the title suggests, is to call attention to somewhat similar phenomena which the authors have encountered in brass and bronze. From a study of the examples given, a more-or-less speculative theory of "inverse segregation" is advanced. Protuberances on Admiralty Brass In the rolling mill of the Scovill Manufacturing Co., there have been found quite commonly bars of certain alloys which had a sort of shaggy roughness on the surface due to slight metallic protuberances. No special attention was paid to these until some bars were found on which these protuberances were heavy enough at the bottom of the bars to produce a blistered appearance. A sample of the protuberances was milled off the surface of the bar illustrated (Fig. la) and upon analysis was found to contain 66.66 per cent. copper, 4.02 per cent. tin and 0.03 per cent. lead, whereas the average composition of the bar was 70.21 per cent. copper, 1.21 per cent. tin, and 0.01 per cent. lead. A sample of the shaggy-rough protuberances at the very top of a bar was also analyzed and was found to contain 2.45 per cent. tin, indicating that it was probably of the same origin as the blistered areas. These results were not entirely unexpected for previous analyses of this alloy had revealed that the surface was richer in tin than the rest of the bar. This, of course, is contrary to what we would expect from a consideration of the equilibrium diagram and has been called "inverse segregation." Fig. 16 is a cross-section of a bar through the protuberances on the surface. It reveals that there is a decidedly different structure through the raised areas and seems to indicate that the bar originally solidified

Jan 1, 1927

By K. F. Veith, R. L. Marovelli, T. S. Chen

An analytical study is made of thermal stress distribution in a thin circular disc subjected to a peripheral thermal shock at various rates of heat transfer. The problem is of importance in predicting the thermal shock response of a rock body of finite size. The theoretical analysis is based on radial heat flow by conduction in the disc and heat exchange by convection between the disc and the surroundings. The case of constant properties and plane stress is treated. Solutions of the stress distribution are presented for both cooling and heating shocks and an average stress theory is formulated. Preliminary experimental verification was obtained from the results of shock tests on thin rock discs insulated on both flat end faces so that heat exchange took place through the exposed peripheral surface. Physical properties vital to the analysis are Young's modulus, tensile strength, coefficient of linear thermal expansion, thermal diffusivity and thermal conductivity. Plots of these properties are presented. Historically, thermal energy has been used for primary rock removal throughout the ages. Although it is not widely known, the fire-setting method of thermal rock fragmentation was still in use 100 years ago in systematic underground mining operations in Scandinavia.' There, the availability of cheap labor and abundant wood fuel made the method competitive with the early blasting powders. By 1880, as high explosives replaced powder, use of the method declined and it was finally abandoned about 1885. Only 40 years ago, some experimental fire-setting methods were used for rock removal underground at Pribram and Zinnwald in Central Europe.2 Compressed air-oil burners replaced the earlier wood fuels. About 15 years ago, gaseous oxygen-oil burners were introduced in the United States and gained acceptance for difficult blasthole drilling and some quarry opera- tions. At present, there is renewed interest in the compressed air-oil burner designs. The literature included information on thermal secondary processes for rock weakening or particle liberation3,4,5,6,7,8 on thermal spallation of rock 9,10,11,12,13 and on the thermal fracture of materials other than rock. The 1955 Symposium on Thermal Fracture14 and the later work of Hassel-man, cover recent developments in thermal shock investigations on brittle ceramics. Although the number of published analytical and experimental investigations conducted on ceramic and refractory materials is large, the literature reveals that there is a lack of information on both the theoretical and actual response of rock to thermal shock. Many of the thermal shock studies on ceramic and refractory bodies are based on the case of heat transfer at the solid's surface by convection in either liquid or air. A similar heat transfer situation was adopted for a theoretical analysis of the thermal stresses in a thin circular disc subjected to a peripheral thermal shock. Experimental thermal shock tests were then conducted on rock specimens to check the analytical results. Specially insulated quartzite, basalt and taconite discs were shocked in either liquid or still air bath at various rates of heat transfer. The work was done in order to resolve the question as to whether theoretically determined tensile stresses are actually realized in a finite rock body undergoing thermal shock. Specifically, if theory predicts that the tensile strength of a rock should be exceeded in a particular type of controlled thermal shock, will fracture occur? This information is needed by Bureau researchers working on thermal and electrical rock fragmentation methods. The object of this paper is to present the main features of the theory and procedure being used in the authors' approach to quantitative prediction of rock response to a thermal shock. THEORETICAL ANALYSIS In the analysis to follow, simple geometry of a thin circular disc is considered. The disc is assumed to be isotropic, homogeneous and perfectly elastic, and to have constant thermal and mechanical properties. The effect of radiation is neglected so that heat is transferred by conduction inside the disc and by convection with its surrounding. In addition, the end

Jan 1, 1967

By Edwin Dudley Martin

DURING the past twelve years the iron and steel industry has made a major advance through the development of the continuous wide strip rolling mill. So far-reaching have been the results that not only has a better product been sold at a lower price but this improvement in quality has permitted manufacturers of products using steel to make important savings in the cost of fabrication. The net result has been a better product at lower cost to the consumer without reduction in either employment or of wages paid within the industry. That is why the iron and steel industry is proud of its attainment. Being a basic industry of strategic importance, such an advance in technology has had its effects on our internal economy, our standard of living, and our industrial power as a nation in both peace and wartime.

Jan 1, 1939

THE decision of the lower court (United States District Court for the Southern District of New York) in the suit of the Dwight & Lloyd Sintering Co., vs. John E. Greenawalt has been affirmed by the United States Circuit Court of Appeals for the Second Circuit. In the original suit, infringement of seven patents was alleged, these covering the process of producing a sinter .out of finely pulverized metalliferous ores as practised in shallow pans operating intermittently in distinction to the Dwight 6: Lloyd continuous machine. The court found that the long delay in bringing suit precluded any recovery of profits from the defendant under the basic down-draft sintering patent, although Dwight & Lloyd are recognized as the inventors of this' contribution to the art and its .importance is acknowledged.

Jan 1, 1928

By H. B. Pulsifer

One of the most common basic open-hearth furnace products is a simple carbon steel with a carbon range from 0.05 to 0.15 per cent. The material is widely used for sheets, tubes, bars, wire and the innumerable special objects of secondary fabrication. The properties of the material vary over wide ranges, depending on the more exact composition and details of manufacture or treatment that affect its structure. The present paper is a review of those properties and structures that have been found by studying this steel as used in the cap screw industry. At first glance this might be thought a narrow application of the steel, but, since the industry uses the material in the cold-worked, annealed and heat-treated conditions, the title of the paper may be excused for its comprehensiveness. Yet, in studying the wide ranges of properties and structures that preclude a more specific title, there can be no suggestion of completeness or finality. Even a summary of a few years' work is no more than a preliminary survey of a field that will be fertile in scientific data and industrial products for many years to come. An outline of the structures will be given first, then a list of the previous contributions that are at hand and finally some details of the work and related problems, especially concerning this low-carbon steel in the surface-hardened condition. Wire Used in Manufacture of Cap Screws The wire that is used for making cold-upset and roll-threaded cap screws has been cold-drawn from hot-rolled rods that were pickled and limed. The common sizes used in the industry range from 0.185 to 0.750 in. dia., the exact diameters depending on the plant practice and having the usual tolerances of 0.002 in. for the smaller sizes and 0.003 in. for the larger sizes. The carbon range, by pit analysis, is usually between 0.07 and 0.12 per cent. Manganese should be within the usual 0.30 to 0.50 per cent. range. Sulfur rarely exceeds 0.045 per cent. and phosphorus seldom exceeds 0.030 per cent. Silicon is usually below 0.03 per cent. but in the silicon-killed steels may be in the customary 0.10 to 0.25 per cent. range. Rimmed steel is not considered most suitable for cap screws that are cold-headed or for parts that are to be surface-hardened.

Jan 1, 1931

By J. J. Carrigan

IN all mining operations a considerable portion of the work performed, especially underground; is accomplished under artificial light, yeti this subject is often not given proper attention. Poor illumination decreases mining efficiency, impairs the sorting or grading of ores, and increases the risk of accidents. In the beginning, and for several years afterward in the metal-mining industry of Butte, Montana, candles placed in candlesticks were carried by the men. Sconces or holders for candles were also provided at stations and curves in drifts to furnish better light for men engaged in. hand tramming. It was also common practice to place clusters of candles on the ground, with no provision for guarding against an underground fire other than the exercise of sufficient care by the men themselves. An accumulation of candle grease from this source was the direct result of the first serious fire in the Anaconda mine, in 1889.

Jan 1, 1936

By A. J. Conelius, D. P. Sobocinski

This paper presents a correlation for predicting the behavior of a water cone as it builds from the static water-oil contact to breakthrough conditions. The correlation is partly empirical and involves dimensionless groups of reservoir and fluid properties and of production and well characteristics. The groups were deduced from the scaling criteria for the immiscible displacement of oil by water. The correlation is based on a limited amount of experimenfal data from a laboratory sand-packed model and on results from a computer program for a two-dimensional, incompressible system. Because the correlating groups are dimensionless, they can be used to estimate the performance of water coning cases not specifically considered in the correlation. However, despite its dimensionless nature, the correlation is not completely general and will not provide meaningful estimates of cone behavior in many situations. INTRODUCTION AND BACKGROUND The production of water from oil wells is a common occurrence which increases the cost of producing operations and may reduce the efficiency of the depletion mechanism and the recovery of reserves. We will deal with one cause of this water production, namely, coning. The coning of water into a producing well is caused by pressure gradients established around the wellbore by the production of fluids from the well. These pressure gradients can raise the water-oil contact near the well where gradients are most severe. Gravity forces that arise from fluid density differences counterbalance the flowing pressure gradients and tend to keep the water out of the oil zone. Therefore, at any given time, there is a balance between gravitational and viscous forces at points on and away from the completion interval. When the dynamic forces at the wellbore exceed gravitational forces, a cone of water will ultimately break into the well to produce water along with the oil. We can expand on this basic visualization of coning by introducing the concepts of stable cone, unstable cone and critical production rate. For instance, if a well is produced at a constant rate and the pressure gradients in the drainage system have become constant, a steady-state condition is reached. If, at this condition, the dynamic forces at the well are less than the gravity forces, then the water or gas cone that has formed will not extend to the well. Moreover, the cone will neither advance nor recede, thus establishing what is known as a stable cone. Conversely, if the pressure in the system is in an unsteady-state condition, then an unstable cone will continue to advance until steady-state conditions prevail. If the flowing pressure drop at the well is suffcient to overcome the gravity forces, the unstable cone will grow and ultimately break into the well. It is important to note that in a realistic sense, stable cones may only be "pseudostable" because the drainage system and pressure distribution generally change. For example, with reservoir depletion, the water-oil contact may advance toward the completion interval, thereby increasing chances for coning. As another example, reduced productivity due to well damage requires a corresponding increase in the flowing pressure drop LO maintain a given production rate. This increase in pressure drop may force an otherwise stable cone into a well. The critical production rate, well known in the literature, is the rate above which the flowing pressure gradient at the well causes water (or gas) to cone into the well. It is, therefore, the maximum rate of oil production without concurrent production of the displacing phase by coning. At the critical rate, a built-up cone is stable but is at a position of incipient breakthrough. Numerous papers have been published on critical rates. Some of the better known of these include the work of (1) Muskat and Wyckoff,' who first dealt with the coning problem; (2) Chaney, et al,' who developed expressions similar to those of Muskat but who presented results in a conven ient-to-use graphical form (the "Sun" method); and (3) Meyer and Garder,b hose analysis is based on radial-flow formulas. One assumption in critical production rate analyses is that the cone has built-up to just before its breakthrough into the well. But, these analyses reveal nothing directly about the time it takes for the cone to build up to this incipient breakthrough position. Thus, water-free oil can be produced from a well for prolonged periods at rates above the critical rate before the well reaches the condition to which the critical rate applies. The published literature contains little on the rate of growth of a cone. Experimentally, Meyer and Searcy studied the rate of rise of a cone in a Hele-Shaw model.' Additional related work on water breakthrough and produced water-oil ratios in water driven reservoirs was reported by Muskat," Hutchinson and Kemp," Henley, et al,' and Stevens, et a1.B Theoretically, the basic coning equations for a water-oil system can be developed by applying the conservation of mass to each of the phases, relating flow velocities with pressure by Darcy's law, and relating pressures across water-oil interfaces by capillary pressure. With the usual boundaries at the well and reservoir limits, the solution of the resulting equations for the time behavior of a water-oil interface constitutes a free-surface, boundary-value problem. The shape of the boundary depends on the internal potential distribution, while this

Jan 1, 1966

By AIME AIME

MORE than thirty members of the Coal Division attended the Coal Land Valuations Round Table on Monday morning. Chairman Dilworth stated that the Committee had been appointed to take up the question and, after reading the list of members of the Committee, pointed out that the object of the meeting was to formulate a plan of action rather than to discuss any phases of valuation, per se. To this end he presented a tentative outline of points to be considered in the future by the Committee. After a lively discussion on the desirability of inclusion of some questions in the agenda of the Committee, the following outline was adopted :

Jan 1, 1931

By R. M. Hays

At the present time, oxidized taconite and semitaconite are not processed on the Mesabi Range except in vely limited tonnages. However, it is estimated that by 1990 shipments from the Range will approach 75 million tons of iron ore per year. To achieve this and future production, either additional magnetic taconite reserves must be proven or oxidized taconite and semitaconite must be processed. One beneficiation process which uses high-intensity magnetic separation and flotation for concentrating oxidized taconite and semitaconite is described. Detailed metallurgical results are given and an economic evaluation of the process is presented with comparison to other processes. The results of the present study indicate that the high-intensity magnetic separation and flotation process appears nearer commercialization for the processing of Mesabi Range semitaconite. The disadvantages of the process are nearer solution and are being solved by well-defined programs. During the twentieth century, the Mesabi Range in northeastern Minnesota has been the main source of iron ore for American steel mills. The Mesabi Range, which is about 120 miles long and up to 3 miles wide, is the pre-glacial outcrop of a group of sedimentary iron-bearing rocks known as the Biwabik formation. The formation, which is 200 to 650 ft thick and dips 50 to 10° to the southeast, is divided into four stratigraphic units. From top to bottom, these are the Upper Slaty, Upper Cherty, Lower Slaty, and Lower Cherty. Since its deposition in Precambrian time, most of the original Biwabik formation has been subject to alteration. Thus, although the iron content of the original formation was quite uniform, major variations in mineral composition now occur both laterally along the length of the formation and vertically within its units. Details of the mineralogical variations in the Biwabik formation have been described by Wolff,' Gruner, 2 and White.3 The unaltered portion of the Biwabik formation includes the magnetite taconites which are being commercially processed by Reserve Mining, Erie Mining, Eveleth Taconite, National Steel, Butler Taconite, and U.S. Steel. These six operations have a capacity of 32 million tons of iron ore pellets per year and have produced approximately 170milion tons of pellets since 1956. Capacity for another 30 million tons of pellets per year is being considered by the industry for the next ten years. This increase will be obtained by constructing new plants and by expanding present operations. Thus, by ! 978, it is estimated that approximately 60 million tons of iron ore vellets will be produced each vear from the magnetite taconites of the Biwabik formation. The portions of the Biwabik formation subjected to intense alteration resulted in direct shipping, wash, and heavy-media ores. Since 1892, 1.8 billion tons of direct shipping ore have been shipped from the Mesabi Range. This ore has been the major source of iron ore for American steel mills. In 1967, about 11 million tons of direct shipping ore and 13 million tons of wash, jig, heavy-media, and other gravity concentrates were shipped from the Mesabi Range.4 These products generally have poorer physical and chemical properties than the iron pellets produced from magnetic taconite. It is predicted that the shipment of these materials will decrease from 24 million tons in 1967 to 6 to 8 million tons in 1975.' This decrease will

Jan 1, 1970

By E. P. Polushkin

The object of this paper as to show that the structural composition of an alloy may be found by the planimetric measurement of the total area occupied by each of the constituents on a few representative photomicrographs of this alloy. When the area is determined the volume and the proportional weight of the constituent may be calculated. This method has been used for the determination of the structural composition of binary eutectics and other binary alloys with known constituents; also the composition of unknown constituents in binary alloys. The accuracy of the method is. high enough to justify its application to metallographic problems instead of the chemical analysis. THIS work has for its purpose the establishment of a new method for determining the structural composition of alloys. The area occupied by a constituent on a few representative photomicrographs of the alloy is measured, by a planimeter, especially designed for metallographic work, and the volume and proportional weight of the constituent calculated. Experiments have shown that 'the results are accurate enough to justify the application of the method to many problems in metallographic research instead of chemical analysis. The advantage of the method is the possibility, of determining the amount of the constituents with-out separating them from the alloy; their composition may also be determined if the ultimate chemical analysis of the alloy is known. DESCRIPTION OF PLANIMETER Suppose Fig. 1 represents a part of a photomicro-graph on which the total area of the black figures is FIG. 1?-PART OF PHOTOMICROGRAPH ON WHICH TOTAL AREA OF BLACK FIG- URES IS TO BE FOUND. to be found. By a system of parallel lines drawn short equal distances apart all figures may be divided into trapezoids. As the area of a trapezoid is equal to its median multiplied by its altitude, the relation between the total areas of the black and the white figures comprised within each strip is equal to the relation between the sums of medians for these figures respectively.

Jan 12, 1924

By L. L. Swift

AT the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows in some types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing metal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cient of friction. Under most operating conditions the friction depends on the unit pressure of the bearing, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.1 The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measure-ment of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual constituents was developed to fill this need.

Jan 1, 1938