Search Documents

By R. G. Ward, D. R. Gaskell

Using the maximum bubble pressure technique, the densities of iron silicates at 1410°C have been measured blowing helium, nitrogen, and argon. By ensuring equilibrium between the melt and the blowing gas with respect to oxygen potential and by minimizing tempcrature cycling of the furnace, iron precipitation in the melt has been prevented. Thus the previously reported effect of blowing-gas composition on the densities of the melts has been eliminated. Consideration of the oxygen densities of the melts gives an indication of the structural changes accompanying composition change. The density-composition relationship of iron oxide-silica melts in contact with solid iron has been the subject of several investigations1-7 and considerable disparities exist among the various results obtained. Of these investigations, all except one5 have employed the maximum bubble pressure method. In the most recently reported of these investigations1 the density-composition relationship obtained blowing nitrogen differed from that obtained blowing argon. The measured densities obtained under nitrogen were greater than those obtained under argon, the difference being a maximum at the pure liquid iron oxide composition and decreasing with increasing silica content. This observation rationalized the disparities existing among the results of the earlier investigations, showing that two lines, one for nitrogen and the other for argon, could be drawn to fit all the earlier results. No explanation for this phenomenon could be offered. Chemical analysis of rapidly quenched samples of melt for dissolved nitrogen, and direct weighing measurements, excluded solution of nitrogen in the melt from being the cause of the increase in density. The range of blowing gases was extended by Ward and Hendersons who measured the density of liquid iron oxide bubbling helium, nitrogen, neon, argon, and krypton. The measured density was found to decrease smoothly with increasing atomic number of the bubbling gas. The work reported here is a continuation of the program initiated by Ward and Sachdev7 to study the densities in multicomponent melts in which the iron oxide-silica system is the solvent. As such it is necessary to explain or eliminate the anomalous densities of iron silicates under different atmospheres, and the present rede termination was carried out towards this end. EXPERIMENTAL The maximum bubble pressure method of density determination was again employed and the experimen- tal apparatus used was essentially the same as that used by Ward and Sachdev.7 A molybdenum-wound resistance furnace heated an ingot iron crucible of internal diameter 1 in. containing a 2-in. depth of melt. The bubbling gas was blown through a 1/4 -in.-diam mild steel tube onto the end of which was welded a 2-in. extension of 1/4 -in.-diam ingot iron rod, drilled out to 5/32 in., and chamfered to an angle of 45 deg. The blowing tube was introduced to the furnace through a sliding seal and its position was controlled by a vertically mounted micrometer screw which allowed the depth of immersion to be determined with an accuracy of ± 0.01 cm. A Pt/Pt-10 pct Rh thermocouple was located below the crucible and temperature control was effected initially by means of an on-off controller and later by a saturable core reactor. The bubble pressure was determined by measurement of a dibutyl phthalate manometer using a cathetometer. PREPARATION OF MATERIALS Iron oxide was produced by melting ferric oxide in an inductively heated iron crucible in air. The liquid was quenched by pouring onto an iron plate. Silica was prepared by dehydrating silicic acid at 650°C for 12 hr. RESULTS Before any measurements of the density of a melt were made, the density of distilled water at room temperature was measured bubbling helium and argon. Both gases gave the density as 1.00 ± 0.01 g per cu cm which showed that the density of the manometric fluid (dibutyl phthalate) was not affected by contact with the blowing gas. With the furnace controlled by an on-off temperature controller an attempt was made to measure the density of pure liquid iron oxide by bubbling argon. The furnace atmosphere gas and bubbling gas were dried over magnesium perchlorate and deoxidized over copper turnings at 600°C. It was found that the pressure required to blow a bubble at a given depth increased slowly with time, and thus it was impossible to obtain a unique value for the density of the melt. Inspection of the blowing tube after removal from the furnace showed that rings of dendritic iron had precipitated from the melt onto the immersed part of the tube. This is shown in Fig. l(a) where the various "steps" correspond to different depths of immersion. The precipitation of iron was considered to be due to one or both of two possible causes: i) The composition of the liquid iron oxide is that of the liquidus at the temperature under consideration and can be expressed by the equilibrium

Jan 1, 1968

By Che-Yu Li, J. L. Gregg, W. F. Brehm

Oriented, oxygen-doped niobium bicrystals were tested in liquid lithium. The grain boundaries were attacked preferentially. The depth of the penetrated zone varies as (time)2. The penetration was aniso-tropic, had a high activation energy, and increased with the increased oxygen doping level. A possible model was proposed to account for the experimental observations. 1 HE grain boundary penetration of a metallic system by liquid metal has been studied by several investigators. Their results are summarized by Bishop.' Most of these works show that the penetration by liquid metal corresponds to the phenomenon of liquid metal wetting. In the case of a grain boundary, wetting will occur when twice the solid-liquid interfacial tension is smaller than the grain boundary tension resulting in the replacement of the grain boundary by two new solid-liquid interfaces. Other possibilities exist; for example, the atoms of the liquid metal may diffuse into the grain boundary region due to chemical potential gradient. The gradient can be produced by impurity segregation or simply be due to the increase in solubility in the grain boundary region. The penetrated grain boundary in these cases may remain solid at the test temperature. The Nb-Li system has been of considerable interest because of its possible technological applications. For fundamental interest it provides a possibility of studying the grain boundary penetration process which is not controlled by the wetting mechanism. The pure niobium is not attacked by the liquid lithium, but if niobium containing more than 300 to 500 ppm oxygen by weight is exposed to liquid lithium, corrosion occurs at the solid-liquid interface and preferentially at grain boundaries. Previous investigators2-' have proposed that this preferential corrosion at grain boundaries is caused by oxygen segregation there, with subsequent inward diffusion of lithium to form a Li-Nb-0 compound. These investigators also found that the corrosion could be retarded by adding 1 pct Zr to the niobium to precipitate the oxygen as ZrO2 upon proper heat treatment. However, there are no quantitative data on the kinetics of the grain boundary penetration process to test the validity of the proposed corrosion mechanism. In this work an investigation of this penetration process in oriented bicrystals was made as a function of the oxygen doping level in the bulk niobium and the grain boundary orientation. A possible model for the penetration process based on the experimental results was proposed. EXPERIMENTS Oriented niobium bicrystals were grown by arc-zone melting oriented single-crystal seeds.7 These bicrystals contained simple tilt boundary. The [001] directions in the two grains were tilted about a common [110]. The bicrystals were 31/2 in. long and 5 by 4 in. in cross section with the straight, symmetric, planar grain boundary longitudinally bisecting the crystal rod. The bicrystals were doped with oxygen by anodically depositing a layer of Nb2O on the surface in a 70 pct HNO solution at 100 v, using a stainless-steel cathode. The specimens were homogenized by annealing in evacuated quartz tubes at 127 5°C. Oxygen content of the niobium was measured from microhardness values, after DiStefano and Litmman.' Supplementary checks were made with vacuum-fusion analysis.7 Individual test specimens cut from the doped bi-crystal rods, about by by % in. in size, were tested inside double jacket sealed capsules. The inner jacket was niobium, the outer was stainless steel. The niobium inner jacket eliminated the problem of dissimilar-metal mass transfer.' The lithium (99.8 pct pure, obtained from Lithium Corp. of America) was handled only in a purified argon atmosphere in a Blickman stainless-steel glove box. After introduction of lithium, the capsules were sealed by welding. Further detailed experimental procedures are given in Ref. 7. The capsules were heat-treated in vertical Marshall resistance furnaces. Temperatures were controlled to When heating above 1100°C, it was necessary to seal the furnace work tube and flow argon through to prevent failure of the stainless-steel outer jacket of the capsule. Tests were made on 6" 2", 16" 2, and 33" i2" bicrystals at oxygen levels up to 2600 ppm by weight in the 6' and 16" crystals and with 1300 ppm oxygen in the 33' crystals. The oxygen levels were controlled to 100 ppm. Most of the quantitative data were obtained from 16" bicrystals between 800" and 1050°C. The capsules were quenched into water after the test and cut open with a water-cooled abrasive wheel. The capsules were then submerged in water, which dissolved the lithium and freed the specimen. Measurement of the depth of the penetrated zone in the grain boundary was done either on metallographically prepared surfaces or directly on the grain boundary plane after the specimen was fractured in tension in the grain boundary plane. The depth of penetration measured by both methods agreed well. Further details describing these techniques have been reported elsewhere.'p7

Jan 1, 1969

By H. C. Brown

SINCE 1934 the steel industry has been utilizing the spectrograph for supplementing wet chemical analysis in the production control of electric and open hearth furnaces. This means of control made great strides during the war years because of the general acceptance of the spectrograph and the increased emphasis that was placed on rapid control methods. However, in the post war era, with the demand still on increased production, it became apparent that a still more rapid and economical means of production control was needed. Since the spectrograph had been used mostly in the analysis of low alloying and residual elements, it also became apparent that equipment was needed to extend the spectrographic technique to the analysis of the high alloying elements in stainless steel. For these reasons, companies manufacturing spectrographic equipment were prompted to start development work on direct reading instruments. In June 1949, the Applied Research Laboratories of Glendale, Calif., announced that a direct method of spectrochemical analysis for stainless type steels had been developed. This paper will describe the use of the Applied Research Laboratories Production Control Quantometer in the quantitative control of stainless, silicon, and plain carbon steels being made at the Butler Pennsylvania Div. of the Armco Steel Corp. The Armco Butler Div. has one 70-ton electric furnace and six 150-ton open hearth furnaces. The electric furnace is employed in the making of all types of stainless steel and the open hearth furnaces are used for the production of silicon, wheel, and plain carbon steels. The ARL quantometer was purchased primarily for the purpose of controlling the steelmaking in the electric furnace, but its use has been extended for the analysis of final tests (ladle tests) on a number of different types of stainless, silicon, and plain carbon steels. Because of this additional work by the quantometer, substantial savings in manpower and time have been realized by the laboratory. In the analysis of a set of preliminary tests from the stainless steel furnace, approximately 40 min in laboratory time are saved due to quantometric analyses. Despite the fact that more specialty grades of stainless steel are being made in the electric furnace, the average tons per hour have been increased since the quantometer was put into operation. Specialty grades require more furnace time than regular commodity grades of stainless steel. The installation of the ARL production control quantometer was completed on March 13, 1952. By May 1, 1952, the instrument was calibrated for nickel, chromium, manganese, silicon, and molybdenum, which are the elements necessary for the production control of the stainless steel furnace. Within the following month, training of personnel on the quantometer was achieved and a study of the accuracy of the instrument showed that the results obtained were sufficiently accurate for control purposes. Therefore, on June 11, 1952, the quantometer was placed on production control for all types of stainless steels. Starting September 11, 1952, the instrument was gradually placed on ladle analysis (final tests) as the analytical curves were refined and additional curves were drawn. The quantometer has been relatively free of breakdowns since placing it on production control. The samples from only one stainless steel heat have had to be analyzed by wet chemistry because of instrument trouble. The previously existing heat-time record was also bettered by 15 min on a commodity grade of 18-8 stainless steel. Scope of Control In general, the quantometer determines all elements necessary for the production control of all types of stainless steel heats and for the ladle analysis of various types of stainless steel heats. It is also used in reporting final results for silicon, manganese, chromium, nickel, molybdenum, tin, copper, and aluminum on all silicon steel grades and manganese, chromium, nickel, molybdenum, tin, and copper on several plain carbon steel grades. Table I shows the elements and the concentration ranges of these elements in the various types of stainless, silicon, and plain carbon steel that are determined on the quantometer. A study of the results obtained on ladle test samples of stainless steel types 410, 430, 430 Ti, 446, 301, 302, 304, 304L, 305, and 17-7 PH will be discussed. Also included in the study are the results obtained on ladle test samples of a number of silicon steels. Apparatus In order to take full advantage of the potentials of the production control quantometer, the unit has been placed in an air-conditioned room with relative humidity control. The temperature is maintained at 73'22°F and the humidity at 45&5 pct. The air conditioning serves as a precaution to minimize the amount of adjustment and calibration needed during operation. It also reduces contaminating fumes and dust and thereby lessens the necessity for maintenance on the equipment. The quantometer is composed of three units: the high precision multisource unit, the 1.5 meter vertical spectrometer, and the console. The source unit supplies excitation conditions varying from spark-like discharges to arc-like discharges. The voltage to the source unit is supplied by a motor-generator

Jan 1, 1955

By E. R. Russell, N. E. Richards

The current ejyiciency of aluminum cells was derived from the metal produced over a period of time and the theoretical faradaic yield. The difference in the actual amount of aluminum in the cathode at the beginning and end of the period must be determined. The weight of aluminum in the cathode was calculated from the dilution of an added quantity of impurity metal. Use of multiple indicator metals, copper, manganese, and titanium, demonstrated that the weight of aluminum in cells can be determined to within 1 pct with routine but careful chemical analyses. Over intervals of the order of 30 days, current efficiencies reliable to within 1 pct can be obtained. INVESTIGATIONS beginning with those of Pearson and waddington ,' through the most recent published work of Georgievskii,9-11 illustrate the direct relationship between the composition of the anode gas and the applicability of analysis of anode gases to the control of alumina reduction cells. McMinn12 noted the lack of an independent method for measuring cell production efficiency over the short term. There is no doubt that changes in the current efficiency are immediately reflected in the composition of anode gases. However, the accuracy of faradaic yields calculated from gas analyses depends upon the degree of interaction between primary anode gas and Carbon.6 A conventional industrial practice of obtaining long-term current efficiency for production units from mass balances and quantity of electricity is generally insensitive to the impact of planned control of any one or more of the influential reduction cell parameters such as temperature, alumina concentration, and mean interelectrode distance. Consequently, there is a real need in the aluminum industry for a procedure to obtain the absolute cell current efficiency over a short term—10 to 30 days—both for the calibration of values obtained from gas analysis6 and for evaluating the effect of controlling specific parameters in the reduction process. The amount of aluminum produced may be determined by considering the cathode pool as a reduction of an impurity metal in aluminum. Analyses over a period will show a decreasing concentration of the impurity due to the accumulation of aluminum solvent. The increase in aluminum inferred from analyses is the amount produced by the cell during the period. Combining weights of the cell aluminum in the cathode at the beginning and end of a specific period, weights of aluminum tapped and the quantity of electricity passed during the interval will yield the current efficiency. Smart,I3 Lange;4 Rempel,15 Beletskii and Mashovets,16 and winkhaus17 have used dilution techniques to determine aluminum inventory in alumina reduction cells. A technique for determining the weight of aluminum in production cells by addition of small amounts of copper to the aluminum cathode was described by smart.13 The precision in values of the aluminum reservoir through dilution of copper in the cathode ranged from about 1 to 3 pct depending upon the quantity of copper added in the range 0.2 to 0.01 wt pct, respectively. Because the method appears so direct and apparently simple, one would not anticipate difficulties in application to industrial cells. The objective of this study was to resolve this problem associated with the trace metal dilution technique for determining the amount of aluminum in a cell. The approach in evaluating trace metal dilution as a basic factor in determining the weight of aluminum in the cell reservoir, and the absolute current efficiency of the Hall-Heroult cell, was to dilute more than one trace metal in the aluminum cathode so that we could discriminate among complications arising from physical mixing, the possibility of separation of intermetallic compounds, loss of the added elements, and chemical detection. EXPERIMENTAL METHODS These experiments are not complex but require standardized procedures. The technique involves addition of the trace metals to the cathode, knowing when these metals are homogeneously distributed in the liquid cathode, timing of the sampling, employing accurate and precise analytical methods, using reliable procedures for monitoring the amount of electricity passed through the cell, and accurate weighing of aluminum removed from the cell during the particular period. More accurate results might be obtained if the increment in concentration of the added indicator metals were of the order of 0.1 to 0.2 wt pct. The method must be applicable to production units and, hence, the contamination of the aluminum minimized. For this reason, the concentration of trace metals in the cathode was kept below 0.07 wt pct and generally at 0.04 wt pct level. Trace quantities of copper, manganese, titanium, and silicon are already present in virgin aluminum and are suitable as additives from electrochemical and analytical points of view. Concentration of silicon is quite dependent upon the characteristics of the raw materials and was not used extensively in this work. Chemical Analyses. All instrumental analyses require calibration against an absolute technique such as a gravimetric, volumetric, or spectrophotometric method which represents the ultimate in sensitivity, precision, and accuracy. On review, the best methods for copper appeared to be optical absorption without

Jan 1, 1969

By C. J. Bechtoldt, H. C. Vacher

Quenched alloys, prepared by powder metallurgical techniques, were examined by microscopic and X-ray diffraction methods. The compositions and heat treatments were chosen so that the chromium and nickel solvuses could be determined and a range of composition and temperature, in which a eutectoid had been reported, could be explored in small intervals. The results showed no evidence of eutectoid reactions having taken place. ALLOYS containing iron, chromium, molybdenum, and nickel are extensively used in high-temperature applications. In order to provide basic information on the solid-state reactions that occur in such alloys, the National Bureau of Standards is engaged in an extensive study of the equilibrium phases in the binary, ternary, and quaternary systems involving these four metals. Attention was directed to the chromium-nickel system because a review of the literature showed conflicting data. A recent compendium1 of the constitution of binary alloys gives two diagrams for the chromium-nickel system, one a simple eutectic and the second a diagram showing a eutectoid and a eutectic. The eutectoid was the result of an allotropic transformation in a high-temperature solid-solution form of a chromium-rich phase called 0. The approximate temperature and composition of the eutectoid was 1200°C and 30 at. pct Ni. In the preliminary study, at the Bureau, no transformation was indicated in the chromium-rich phase of ternary and quaternary alloys in which chromium and nickel were major components. Similar results have been reported from time to time in the literature,2-8 In consequence of this situation, a systematic study was made of the constitution of heat-treated chromium-nickel alloys using metallographic and X-ray diffraction methods. The compositions of the alloys were selected so as to determine the boundaries of the chromium-rich and the nickel-rich phases and to explore in small intervals the ranges in composition and temperature in which the eutectoid had been reported. The results of this study are reported and discussed in the present paper. EXPERIMENTAL PROCEDURES Materials, Alloys, and Heat Treatments—The alloys were prepared by a powder metallurgy technique similar to that used in earlier work.9 Analyses of the materials used are given in Table I. Powders were mixed using a vibrator in 30-g batches of predetermined composition; 2-g pellets were made from the mixture by compacting at room temperature in a 1/2-in. diam mold under 60,000 lb per sq in. pressure. The pellets were sintered in dry hydrogen for 10 days at 1300°C. At the end of the sintering treatment the specimens were quenched in water, which caused a pale green film to form on the chromium-rich alloys and thin black scale to form on the nickel-rich alloys. The pellets after sintering were approximately 1/2 in. diam by 3/32 in. thick. The purification train9 was modified by inserting a tube of titanium turnings, heated at 700°C to increase the efficiency of the removal of oxgen and nitrogen. It was found in the earlier work that the sintering treatment lowered the carbon, oxygen, and nitrogen contents of chromium-rich alloys to 0.01, 0.01, and 0.004 wt pct, respectively, and that there was a loss of chromium. In order to ascertain the extent of this loss, the chromium contents of certain alloys were determined chemically. They included those alloys used to determine the parameter-composition curves and those of critical composition, used to determine the chromium-solvus microscopically; these analyses were made on samples after the final heat treatments. The mixed powder values for the chromium content of those alloys that were not analyzed were adjusted to conform to a smooth curve based on the chemically analyzed values for

Jan 1, 1962

By C. W. Covington, H. C. Cook, J. F. Libsch

Sputtered aluminum thin films were prepared in each of two conventional bell-jar vacuum systems. One system utilized an inner "getter sputtering" enclosure; the second system was a standard diode sputterirlg arrangement. Consistent and repeatable film properties were obtained in both systems provided sufficient cleanup and presputter time was allowed. The various problems associated with aluminum sputtering are discussed, with pavticular attention to the vzinimization of film contamination by outgassing and oxidation. The growth and structure of the aluminum thin films were studied with the aid of electron wzicroscopy and related to deposition rate, substrate temperature, and film thickness. The resistivity of the films was correlated to film structure and surface roughness. Resistiuities as low as 3.5 microhm-cm (2.3 x bulk resistiuity) were measured for relatively thick films (20,000). THIS investigation was undertaken to explore the problems and film characteristics associated with the sputtering of aluminum. Earlier work reported on aluminum sputtering has stressed the contamination of both the cathode and film as well as abnormally low deposition rates.' Data on sputtering yields,3 however, indicate that aluminum sputtering could be practical. Recently, it was shown by Theuerer and Hauser3 that aluminum sputtering was feasible in a conventional oil-diffusion pumped vacuum system provided an inner "getter sputtering" enclosure was employed to minimize gaseous contamination. This technique employs the getter action of aluminum to produce extremely low reactive gas partial pressures in the deposition zone. Aluminum films have already found use in solid-state electronic devices such as transistors and integrated microcircuits. To the present time, most aluminum films have been prepared by evaporation due to the ease with which this metal can be evaporated. Controlled sputtering of aluminum offers a number of advantages over evaporation, however, such as 1) manufacturing compatibility with other metals which must be sputtered, 2) better control of process variables resulting in more repeatable and uniform films, 3) generally better adhesion resulting from higher-energy metal atoms, 4) built-in material supply for continuous operation, and 5) the ability to deposit alloys. The data presented in this paper are the result of two separate studies. One study utilized a small "getter sputtering" enclosure (System A) and was concerned with the structure and properties of thin aluminum films up to about 1600A thick. In this thickness range, study of the film structure was possible with transmission electron microscopy. The second study was conducted with a conventional diode sputtering apparatus (System B) and covered $ much wider range of film thickness up to about 34,000A. Emphasis was placed on developing techniques which would extend aluminum sputtering to an existing in-line continuous deposition process.4 I) EQUIPMENT AND PROCEDURE System A. Fig. 1 shows a schematic of the "getter sputtering" inner chamber used and Fig. 2 is a photograph of this chamber mounted on an 18-in. access ring of a standard liquid-nitrogen trapped bell-jar vacuum system. This chamber was designed after a similar system used by Theuerer and auser.3 The configuration allowed the glow to emanate in all directions from the cathode. Argon (99.99') was allowed to enter only at the top of the chamber such that most of the reactive gases entering with the argon were reacted with the aluminum vapor and deposited on the chilled walls of the chamber before reaching the deposition zone. Provision was also made as shown, Fig. 1, for heating and cooling the substrate from about 20" to 400°C. Two substrate materials were used: Corning 7059 glass (12 by 12 by 0.048 in.) and carbon films about

Jan 1, 1967

By Charles Stein

The effects of several different prior treatments an the creep behavior of 99.9995 pct aluminum at 260°C and 1000 psi canstant stress are compared with annealed specimens. Quenching from 538oC, irradiation with 2 mev electrons, and tension-compression room temperature fatigue damage were used to change the substructure of the specimens prior to their creep testing. The quenched and the irradiated specimens showed a larger primary and transient stage contribution to the creep curve than those specimens which were only annealed prim to creep testing. The specimen receiving prior fatigue damage at room temperature showed no first stage or transient creep when tested under identical conditions as the above specimens and had an average creep rate seven orders of magnitude lower than that of either the annealed, the quenched or the irradiated creep specimens. In a previous electron transmission microscopy investigationl of the substructure developed during the creep of pure aluminum at 0.57 Tm, it was noted that a large concentration of vacancy loops and dislocation loops were present in and near the subboundaries while the interior of the subgrains contained few of these defects and had a low dislocation density, see Fig. 1. Yim and Grant2 and Hazlett3 have shown that the presence in nickel of a substructure developed by prior cold work effectively reduces the primary and transient contributions to the creep curve. Hultgren,4 McLean,5 Gervais, Norton, and Grant,6 Chang and Grant,7 and others have shown the same effect with the higher stacking fault energy material, aluminum. However, the specific defect responsible for the change in the creep behavior developed by the prior cold work was not established. Specifically, what effectively interfered with dislocation motion in these materials at elevated temperatures? Was it jogs on dislocations produced by their interaction with other dislocations or with vacancy or dipole loops, see Fig. 1, or did the subgrain walls determine the mean free path for glissile dislocations? This would be a realistic possibility only if subgrain boundaries are effective barriers to dislocation motion. The ability of a subgrain boundary to act effectively against glissile dislocations depends on the number and the arrangement of dislocations in the subboundary,8 which in turn is a function of the creep strain.' This paper compares the creep rate of specimens possessing a large vacancy concentration to that of annealed specimens and with specimens having a stable subboundary wall containing Lomer locks produced by prior fatigue damage. EXPERIMENTAL PROCEDURE Vacancy Loops. Aluminum creep specimens, 99.9995 pct pure, were machined from zone refined rod to a 2-in. gage length and a cross-sectional area of 0.025 in. These specimens were annealed at 538oC, 1000°F, for 10 min and quenched into ice water. They were then reheated to the creep test temperature of 260°C, 500°F, and held at this temperature for 18 min to al-low for vacancy condensation and loop formation. The specimens were subsequently creep tested at 1000 psi constant stress at 260°C. The temperature along the gage length was monitored by three Pt-Pt, 13 pct Rh thermocouples, two embedded in the upper and lower shoulders of the specimen and one attached to the mid-point of the gage length- The temperature gradient was held to ± l°C or less throughout the Creep test. Elongations were measured by two LVDT's 'connected in an averaging 'On-figuration, with quartz extension arms placed against the specimen at the extremes of the 2-in. gage length. i K 3J?--' * *H - >^> - ' ^L r 77 . *y J OJL, J Fig. 1—Transmission electron micrograph of pure aluminum strained 8.2 pct at 260°C and 1000 psi constant stress. Note the presence of numerous loops near the light dislocation tangle

Jan 1, 1970

By G. K. Manning, W. E. Few

T has been known for some time that both'inter-granular carbide and intergranular oxide phases cause brittleness in molybdenum. Parke and Ham' indicated that 0.0025 pct 0 present in molybdenum after solidification from the melt was sufficient to induce intergranular brittleness during forging. However, material containing 0.06 pct C could still be forged. However, adding this amount of carbon to insure deoxidation causes the formation of carbides on freezing. These carbides are precipitated at grain boundaries, and Rengstorff and Fischer' have shown they have an unfavorable effect on the room-temperature ductility of molybdenum. Take? in 1928 proposed that the solubility of carbon was a constant value of 0.30 pct from room temperature up to 1800°C. In 1935, Sykes, Van Horn, and Tucker' obtained X-ray data suggesting that the solid solubility of carbon in molybdenum was between 0.07 and 0.09 pct at temperatures from 1500" to 2100°C. The a-solubility line for carbon was included in the Mo-C diagram given in the Metals Handbook as a tentative line based on the data of Sykes, Van Horn, and Tucker. In order to determine the partial phase diagrams for these systems, it was necessary to construct a high-temperature furnace suitable for heat treating molybdenum at temperatures up to 4000°F. A molybdenum resistance furnace was built for this purpose in which samples could be heat treated in a purified atmosphere and quenched from any desired temperature.' Experimental Work Solubility of Carbon: Arc-cast molybdenum supplied by the Climax Molybdenum Co. and 18-gage molybdenum wire samples produced by powder metallurgy at the Fansteel Metallurgical Co. were used in determining the a-solubility line for the MO-C system. The cast molybdenum contained 0.032 pct C initially. Two lots of 18-gage wire were used, one containing 0.011 pct C and the other 0.005 pct C initially. All material contained a carbide phase as received. Fig. 1 illustrates the carbides found in the untreated material. Heat treatment in a purified hydrogen atmosphere was found to reduce the carbon content in the as-cast molybdenum. Purified argonT also decarburized molybdenum samples at temperatures above 3500°F; however, the carbon content remained constant during heat treatment in purified argon at lower tem- peratures. The argon was purified by passing it over titanium at 750 °C and then through a magnesium perchlorate drying tower. The hydrogen was purified by passing it through a commercial hydrogen deoxidizer, followed by a drying tower. Specimens having different initial carbon contents were heat treated in argon at 3500°F for periods ranging from 5 min to 5 hr and were analyzed for carbon. Samples of the same final carbon content had the same microstructures regardless of time at temperature. Furthermore, a gradient between center and surface in the amount of undissolved carbide particles present was never observed. It was concluded that at these low carbon levels, and at the high temperatures involved, diffusion proceeds so rapidly that the specimen is always substantially homogeneous in carbon content, in spite of the gradual loss in carbon. Based on the above findings, the following procedure was used to determine the carbon-solubility limit at 3000°, 3500°, and 4000°F. At each of these temperatures, a number of samples were heat treated, as shown in Table I, and rapidly cooled to room temperature. Since the samples lost carbon in proportion to the length of time heated, a series of samples were obtained of varying carbon contents. By use of a rapid cooling rate, the phases present at the high temperature were retained at room temperature. All samples were examined microscopically. Those found to contain either no excess carbide phase or only a very small amount were then analyzed for carbon. The samples actually analyzed for carbon

Jan 1, 1953

By B. F. Decker, J. H. Keeler, W. R. Hibbard

Textures of hot-rolled, of cold-rolled, and of cold-rolled and annealed zirconium sheets were determined by use of an X-ray spectrogoniometer. All textures showed a tilt of the basal planes 240" from the rolling plane about the rolling direction. Deformation textures showed the [1010] direction to be approximately in the rolling direction. After recrystalliza-tion, the 111201 direction was approximately in the rolling direction. This texture was sharpened by annealing above the allotropic transformation. Textures of sheet produced by alternately cold rolling and then annealing were less strongly oriented than sheets that underwent severe deformation without intermediate anneals. THIS study of the deformation and annealing textures of high purity zirconium was carried out to supplement an investigation of zirconium and zirconium-base alloys. The spectrogoniometer method of pole figure determination was used and yielded more detailed and precise information than the photographic techniques used by previous investigators. Earlier investigations of the rolling textures of hexagonal metals titanium,1,2 beryllium," and zirconiumL having a c/a ratio slightly less than 1.6 disclosed a rotation of the basal planes from the rolling plane about the rolling direction so that the basal poles were inclined toward the transverse direction, and with one exception,& the [1010] direction was found parallel to the rolling direction. Similarly, hot rolling produced a spread of the basal poles in the transverse direction,2,3,5 With the [1010] direction parallel to the rolling direction. The textures of these metals after recrystallization differ somewhat from each other although still exhibiting the transverse rotation of the basal poles about the rolling direction. Zirconium" was found to have the [1120] direction in the rolling direction, beryllium" continued to have the [1010] direction in the rolling direction, and titanium' was shown to have the [1010] direction in the rolling direction (the cold-rolling texture) when annealed at 1000°F, changing to the [1120] direction in the rolling direction when annealed at 1500°F. It was suggested2 that the titanium retains the deformation texture after re-crystallization, and preferred grain growth at higher temperatures produces the second texture. Annealing above the allotropic transformation temperature did not appreciably change the high temperature recrystallization texture for titanium.' Coarsegrained zirconium showed more spread" in the transformation texture than in the recrystallization texture. The material used in this investigation was crystal-bar zirconium prepared by the iodide process. The major impurity was hafnium which was less than 0.3 pct. The composition obtained by spectro-graphic analysis is given in Table I. The hot-rolled specimen was prepared from a 50-g button of zirconium arc-melted in a water-cooled crucible under an argon atmosphere. This button was enclosed in a welded sheath of soft iron and the ensemble was rolled at 825°C. After each pass the sheath was put back into the furnace to allow it to return to the desired temperature. The zirconium ingot was reduced in this manner to a thickness of about 0.035 in., a reduction of approximately 90 pct. The sheet after removal from the sheath was alternately polished and etched to a thickness of 0.001 in. Cold-rolled specimens were prepared from crystal bar by a series of reductions of approximately 0.010 in. until the sheet reached a thickness of 0.010 in. after which it was cold-rolled to 0.001 in. thickness between sheets of alloy steel. The total cold reduction amounted to about 99.8 pct. Specimens were annealed in an evacuated Vycor or quartz tube. The transmission pole figures were obtained by the quantitative method of Decker, Asp, and Harker6 modified by Geisler7 using an X-ray spectrogoniometer with Cu Ka radiation. Unless otherwise specified all four quadrants were examined with 5" increments along the radius of the pole figure. Absorption corrections were made for changes in length of the X-ray path through the sample as inclination of the

Jan 1, 1954

By A. L. Barnes

A number of reservoirs have been partially invaded by bottom water. Water flooding such reservoirs can be especially inefficient if the oil has a high viscosity because injected water will under-run the oil and emerge at producing wells without having displaced much oil. A possible means of improving water sweep efficiency would be to precede the water flood with a slug of water purposely thickened with a chemical additive. This possibility has been studied with a scaled laboratory flow model. The investigation was carried out on a model representing a 20-acre five-spot with one set of reservoir condition~. Displacements were performed with water, with viscous-water slugs of 10 and 25 per cent of the pore volume followed by water, and with all viscous water. Displacement tests were made at several rates of injection. For all cases, compared at the same producing water-oil ratio, an increase in rate resulted in an increase in volumetric sweep. The larger the quantity of viscous slug injected, the greater the crossflow of oil ahead of the displacing front and, thus, the lower the WOR during that period of a displacement. This investigation indicates that the injection of aqueous viscous slugs in this type of system would give some additional benefit over conventional flooding by (I) reducing the life of the flood, (2) reducing lifting costs and (3) increasing ultimate recovery. The benefits of a viscous-slug displacement would warrant its use if the viscous water could be created for a few cents per barrel. INTRODUCTION The most appropriate method for water flooding oil reservoirs which have been partially invaded by bottom water has been a problem of considerable interest. Such reservoirs, having good vertical permeability and unfavorable mobility ratios, are difficult to produce efficiently under normal waterflood procedures. Even though the injection wells have been plugged back above the oil-water contact and the water zone has been squeezed off, injection water will enter the formation and not only displace oil, but also much of it will displace the bottom water, thus creating a high producing water-oil ratio at the start of a flood (see Fig. 1). Since the rate of injection and the viscosity of the displacing fluid are the more easily controlled physical parameters of the reservoir, it is quite natural to study their effects on the volumetric sweep of the oil zone and on the producing water-oil ratio. Increasing the viscosity of the displacing fluid has two disadvantages—it reduces the maximum rate of injection into the reservoir, and it costs more than water. It was thought that the injection of a viscous-fluid slug, followed by water, would minimize these two disadvantages, increase the volumetric sweep of the oil zone and reduce the producing water-oil ratio. Water with an additive to increase viscosity would probably be the most effective. The primary purpose of this investigation was to determine the feasibility of injecting viscous-water slugs followed by water to improve or hasten oil recovery while reducing the producing water-oil ratios. The effect of injection rate upon recovery was also investigated. A laboratory model, scaled to a 20-acre five-spot prototype with one set of reservoir conditions, was constructed. Laboratory studies of displacements with (1) water, (2) viscous-water slugs of 10 and 25 per cent of the pore volume followed by water and (3) all viscous water were performed at several rates of injection. THEORY OF SAND MODEL SCALING There are two conventional means of determining scaling criteria. These are dimensional analysis and inspec-tional analysis. Determining scaling criteria by dimensional

By Norman F. Schulz, Emert W. Lindroos, Strathmore R. B. Cooke

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (-—CH,CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder" has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate—potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality. of the preparation of the aminoethyl starch: "Three hundred and sixty grams of powdered unmodified corn starch was slurried in 3 liters of water and stirred during gelatinization. Eighty-six grams of ethylenimine was added slowly during reflux which was continued for 4 hr. The yellow solution set to a gel upon cooling. This was broken up and neutralized with HC1. The thick paste was dried on hot rolls. Adsorbed polyethylenimine and salts were removed from the yellowish products by washing first with acidified aqueous '60 per cent' alcohol. The white product contained nitrogen corresponding to about one aminoethoxy group per ten glucose residues." Only laboratory samples of this starch derivative have been prepared. The starch reagents for use in flocculation, flotation, and adsorption tests were made up by dispersing the appropriate quantities of air-dry starch in cold water, adding boiling water, and heating for 30 min at 120°C under pressure. When used ip adsorption tests, the starch solutions first were cleared of insoluble matter by centrifugation.

Jan 1, 1953

By Strathmore R. B. Cooke, Emert W. Lindroos, Norman F. Schulz

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (-—CH,CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder" has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate—potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality. of the preparation of the aminoethyl starch: "Three hundred and sixty grams of powdered unmodified corn starch was slurried in 3 liters of water and stirred during gelatinization. Eighty-six grams of ethylenimine was added slowly during reflux which was continued for 4 hr. The yellow solution set to a gel upon cooling. This was broken up and neutralized with HC1. The thick paste was dried on hot rolls. Adsorbed polyethylenimine and salts were removed from the yellowish products by washing first with acidified aqueous '60 per cent' alcohol. The white product contained nitrogen corresponding to about one aminoethoxy group per ten glucose residues." Only laboratory samples of this starch derivative have been prepared. The starch reagents for use in flocculation, flotation, and adsorption tests were made up by dispersing the appropriate quantities of air-dry starch in cold water, adding boiling water, and heating for 30 min at 120°C under pressure. When used ip adsorption tests, the starch solutions first were cleared of insoluble matter by centrifugation.

Jan 1, 1953

By C. G. Dunn, F. W. Daniels, M. J. Bolton

IN recent investigations1. a data on relative grain boundary energies in silicon iron have been obtained. The present investigation is a continuation of this work along similar lines for the purpose of obtaining additional information on boundary energies. One aim has been to extend the data for a (110) series, which was formerly studied,' to small differences in orientation, since a recent theory3,4 based on a dislocation model of grain boundaries predicts a E. ? (A-ln ? )* form of energy curve for small differences in orientation. Another aim has been to provide data for a (100) series—all grains having (100) planes parallel with the surface of sheet speci-mens—and to compare the results with the predicted form of energy curve. Finally, information on the nature of approach to equilibrium conditions was to be obtained through observations on the movements of grain boundaries. Recently published papers2,3,5 have treated the mathematical problem of expressing equilibrium conditions for grain boundaries for the general case when boundary energy depends upon boundary orientation. The equilibrium equations, which relate equilibrium angles and grain boundary -free energies, contain additional terms that express the variation of energy with boundary rotation. It has been necessary in the present investigation, however, to neglect these additional terms since no data for their evaluation were available. Dropping the additional terms leads to the following approximate equations which were used: E12/sin ?3 = E18/sin?2 =E28/sin?1 or those of the form: E28 + E13 cos ?3 + E12 cos ?2 = 0 Experimental Procedure Except for sample F1, all specimens were made from two lots of silicon iron called C and L respectively. The compositions of these are listed in table I. In the preparation of 12 three-grain specimens for the present investigation, a controlled grain growth technique, which has been described previously,' was used. After preparation, the specimens were notched at the boundaries to shorten them as a means of providing more rapid approach to equilibrium in the anneals. Initial grain boundary angles were determined from micrographs taken at X500. Seven anneals, totaling about two days at 1300°C and two to four days at 1400°C, were run in an atmosphere of pure dry argon as described in a previous paper.' Boundary changes generally could be followed without metallographic surface preparation, because thermal etching occurred during the anneals. These observations indicated angle changes of as much as 35" in some instances, with the major changes occurring during the first anneal. Annealing was discontinued when the angles reached stationary values. Fig. 1 gives a schematic diagram for purposes of defining crystallographic and boundary directions for three grains with common plane parallel with the sheet. Differences in orientations (expressed by A) are the angles between [00l] directions. They can be calculated with the aid of the ?'s. The grain boundary angles can be calculated from the w'S. Results Results are given in table 11. Types of crystal-lographic planes refer to those parallel with the sheet. Orientations are given in terms of [00l] direc-tions as shown in fig. 1. Except for grain 3 of specimen H6, which was unintentionally tilted 7" out of a (100) plane, all grains generally were within 1" or 2" of the plane specified. The directions of boundaries were measured generally to within 1" on both upper and lower surfaces, and the average direc- tions were determined for use in calculating the grain boundary angles. Variations in grain boundary directions refer to deviations from average directions. Boundaries near the junction point for all specimens generally were very close to perpendicu-

Jan 1, 1951

By J. P. Hammond, C. J. McHargue, S. E. Adair

Cold-rolled sheet textures have been determined for binary solid solutions of aluminum, columbium, tantalum, and zirconium in titanium. An alloy containing 3.8 pct Al had a (0002) [10101 texture, whereas alloys with the other elements had rotated (0002) [10101 textures similar to that of iodide titanium. THERE have been relatively few studies of the effect of alloying on deformation textures. A second element may be present in the base metal in solid solution and/or as a second phase. The literature offers no satisfactory explanation for the effects of solid solution alloying on textures noted thus far. For example, there is no satisfactory explanation of the difference in the textures of copper and a brass. The most complete study of the effects of solid solution alloying on deformation textures has been that of Brick, Martin, and Angier.¹ These investigators reported that the copper texture was retained by alloys of copper with up to 30 pct Ni, less than 5 pct Zn, less than 2 pct A1 or Co up to the limit of solubility. Copper containing more than 5 pct Zn, more than 2 pct Al, or the maximum soluble concentration of tin, silicon, or manganese showed the deformation texture of a brass. Bakarian² reported that additions of 0.20 pct Ca to 99.98 pct Mg or 2.0 pct Mn plus 0.15 pct Ca to magnesium resulted in entirely different textures than for the pure magnesium. The texture obtained for high-purity magnesium sheet showed the basal plane to be concentrated parallel to the rolling plane. The texture obtained for the alloy containing 0.20 pct Ca had the basal planes concentrated in elliptical areas whose centers were tilted 15" from the center of the pole figure toward the rolling direction. This split basal orientation was even more pronounced in the alloy containing 2.0 pct Mn and 0.15 pct Ca. Fuller and Edmunds" studied the rolled sheet textures in a zinc alloy containing 1 pct Cu and 0.01 pct Mn. The basal pole figure of this alloy contained a region of strong concentration not found in the pole figure for pure zinc.' In the above cases, results were discussed in terms of possible changes in slip and/or twinning systems and critical shear stresses. However, there were no experimental data to relate these speculations with the observed textures. It has been suggested that the deformation textures of titanium, zirconium, and beryllium could be directly ascribed to their low c/a ratios. The complex deformation mechanisms of titanium" also have been suggested to be characteristic of hexagonal close-packed metals with low c/a ratios. The purpose of this investigation was to study the cold-rolled sheet textures in binary titanium-base a alloys in which the c/a ratios were greater than, less than, and about the same as the c/a for iodide titanium. The annealed textures of these alloys will be reported in a subsequent article. Materials and Methods The chemical analyses of the metals used in this investigation are given in Table I. The alloys were prepared as 15 g buttons on a water-cooled copper block in a vacuum arc-furnace. The furnace was evacuated to pressures of the order of 10.' mm Hg, flushed with 99.98 pct pure argon, and melting was carried out in 0.2 atm pressure argon. Each button was remelted until radiographs and chemical analyses indicated complete solution of the solute elements. All buttons were forged and homogenized 72 hr at 500°C. The buttons to be rolled were ground and etched to sizes and shapes suitable for the rolling

Jan 1, 1954

By A. T. Corey, J. H. Henderson, M. R. J. Wyllie, C. H. Rathjens

The results of three-phase relative permeability tests on nine water-wet consolidated Berea sandstone samples are presented as composite ternary diagranls showing isoperms of oil, water and gas. Capillary pressure control was exercised over the flow of gas and oil in the presence of water. The water saturations ranged from 17 to 71 per cent pore volume. A method of calculating both the oil and water permeabilities of a three-phase system from the easily measured gas relative permeability is presented. EXPERIMENTAL PROCEDURE AND RESULTS A renewed interest has been shown in three-phase relative permeability as a result of recent developments involving underground combustion processes, steam injection, and other multiphase displacement processes. The experiments and results described here involved simultaneous flow of oil and gas in consolidated Berea sand with brine present as the wetting phase. Gas and oil relative permeabilities were measured on nine cores with CaC12 brine present as the wetting phase in saturations ranging from 17 to 71 per cent. The average residual liquid saturation of the cores was approximately 20 per cent. In order to make certain that brine was the wetting phase, the test cores were saturated with brine before contact with hydrocarbons. As an added precaution to avoid having oil displace brine from the wetting position as a result of changing wettability, each core was only used twice, i.e., first with a fixed percentage of brine and then for a gas-oil permeability determination with no brine present. The results, therefore, are presented as composite ternary diagrams representing the flow tests on nine individual cores having very similar properties. All tests were made using a modification of the capillary pressure techniquc described elsewhere. The effective oil permeability was measured before gas was introduced using a very small pressure gradient (a few centimeters of oil). This determination was made without selectively wet barriers in contact with the core. The cores were then placed between capillary barriers and gas-oil relative permeability curves obtained. The capillary barriers had been made water repellent with a silicone treatment. In determining gas-oil-water relative permeability in this fashion, control was exercised over the capillary pressure existing between the gas and oil. No control was exercised over the pressure difference existing between the oil and water. Athough an equal pressure gradient was applied to the gas and the oil phases, this pressure gradient does not exist in the water phase. Since the pressure gradient across the core was always much less than the displacement pressure of the fully saturated core, the pressure gradient can have caused only a very slight distortion of the oil-water interfaces. This slight distortion of the oil-water interfaces had a negligible effect on the validity of the oil permeabilities measured. The oil permeability, measured in the presence of water but with no gas present, was in every case equal. within experimental error, to the gas permeability of the gas-oil system when the oil saturation was the same as that of the water. Gas and oil relative permeabilities were plotted as a function of total liquid saturation. It was found that the gas relative permeability curves obtained on cores with brine present were identical with those obtained on the same cores with no brine present. The denominator for calculating oil relative permeabilities was the permeability found by extrapolation to infinite mean pressure (A la Klinken-berg). Fig. 1 illustrates gas-oil relative permeability results obtained on a typical core. The solid permeability curves represent the experimental data. The dashed oil relative permeability curve was calculated using the relationship;

Jan 1, 1957

By Irving Cadoff, Kurt Komarek, Edward Miller

THE lead-telluride phase diagram as compiled by ansen' has one intermetallic compound, PbTe, with solid-solubility limits extending from 22 to 45 wt pct Te (31.4 to 57.1 at. pct). Pelzel2 redetermined the solubility limits on the lead-rich side of the compound by measuring the relative areas of the two phases in samples annealed in the liquid + compound region, and obtained data that agreed with that of Hansen. Recent studies of the semiconducting properties of PbTe3 however, have indicated that addition of either lead or tellurium to PbTe does not produce samples having carrier concentrations greater than about 10 19 cm-3. Assuming that each impurity atom results in one ionized charge carrier, this carrier concentration corresponds to a solubility range of less than 0.04 at. pct. Fritts and Karrar4 have also observed two phases in samples containing from 0.15 to 3.0 pct excess Pb. To resolve the discrepancy between these data, the solid solubility limits of the compound PbTe were reinvestigated, using several other techniques. Ten 25-g samples with compositions of 1/2, 1, 3, 5, and 10 wt pct excess Pb and Te and two 100-g samples of 15 and 65 wt pct Te were prepared, sealed in evacuated quartz capsules, and melted at 950oC. The 1 pct excess Pb and Te and the 15 and 65 wt pct Te alloys were homogenized for 96 hr at 450°C; the remaining specimens were annealed 50°C below the solidus temperature reported in Hansen. The specimens were polished and etched with dilute HNO,. All the samples were two phase, the second phase appearing at grain boundaries or as spheroidized inclusions in the grains. In the case of the tellurium rich specimens, the second phase could be identified as a eutectic. Debye-Scherrer powder diffraction patterns of the i, 1, 3, 5, and 10 pct excess samples were obtained using CuKa filtered radiation. The films were indexed as the B1 or NaCl structure. The calculated lattice parameter of PbTe was the same for all the specimens, with an average of a0 = 6.460 ± 0.0005A. Lines due to excess lead or tellurium were very faint but could be clearly seen in all the films. The relative areas of the two phases in the 15 and 65 wt pct Te samples were corrected for the differences in density of Pb, Te, and PbTe, and taken as proportional to the relative volumes of the two phases. The corrected relative volumes agreed with a phase diagram having negligible solubility of both lead and tellurium in lead tellurium. The density of the two specimens was obtained to give a third independent determination of the phase limits. The specimens were broken into small pieces to eliminate any internal porosity, and adherent air bubbles were removed by vigorous shaking under water for several hours. The density of lead (11.34 g per cm3) and of tellurium (6.25 g per cm3) was taken from the International Critical Tables and that of stoichiometric PbTe (8.25 g per cm3) calculated from the lattice parameter. For the 15 wt pct Te samples, the density assuming no solubility was calculated to be 9.89 g per cm3; the observed density was 9.86 g per cm8. For the 65 wt pct Te alloy, the density calculated for the case of no solubility was 7.24 g per cm3; the measured density wag 7.22 g per cm3. These results are consistent with those of planimetry and X-ray. SUMMARY Data have been presented which show that the solid solubility of both lead and tellurium in PbTe is

Jan 1, 1961

By H. C. Vacher, C. J. Newton

EXTENSIVE investigations in the field of residual strain measurement by X-ray diffraction have been made by Bollenrath, Hauk, and Osswald,1 by Smith and Wood,2'3 by Greenough; by Rosenthal and Norton." and many others. Since X-ray strain measuremeits apply only to those crystals of the test body which are of the proper condition and orientation to diffract and since the residual strains revealed may be accompanied by either body or tex-tural stresses, there has been considerable disagreement among investigators with respect to the validity of conclusions in this field. Although the experi-mentors have employed a variety of loading schemes, surface preparations, and X-ray wave lengths, the observations almost invariably have been made only on the outer surfaces of the specimens. The present note is not to be construed as an exposition of a new method of stress analysis by X-ray strain measurements on sections but as a presentation of some results which point to interesting possibilities for further experiments with sections. The two test rods used in this study were of ingot iron annealed at 910°C. The initial length of the gage section was 2 in. and the diameter was 0.415 in. Cross-sections were cut from the ends of the annealed rods to provide strain-free material. The tensile rod was axially loaded the desired amount in a commercial testing machine. A 1 in. portion of the gage length was cut from the other rod and was subjected to compression in the same machine. Details of this plastic straining of each rod are given in the upper half of Table I. A half-cylinder piece about 1/4 in. long was obtained by making a short longitudinal plane cut containing the axis of the rod near the center of the gage length. From adjacent material a disk about 1/8 in. thick was cut to provide the cross-section specimen. Later another section was cut from this same region with an angle of 30" between the normal to its surface and the axis of the test rod. A cross-section and a longitudinal section were cut from the compression rod in a similar manner. All of these as well as the strain-free cross-sections were mounted in Bakelite and used as specimens for the following X-ray strain measurements. During the course of the study, it became apparent that the condition of the surface of a specimen was a highly critical factor. One of the annealed strain-free specimens as a control was subjected to about 24 hr of polishing with fine alumina, interrupted about every 2 hr for etching with 1 pct nital. Its lattice parameter was determined at intervals from measurements on back-reflection X-ray diffraction patterns, which were calibrated with diffraction from tungsten powder. The parameter gradually approached the value found in the literature for strain-free iron and remained there, within the limits of the experimental error. This determined a long polishing and etching procedure which was adopted for all the specimens and which gave X-ray results from the surfaces believed to be representative of each specimen as a whole. A large number of back-reflection patterns were made with cobalt and chromium radiation, all at normal incidence. Except for some preliminary stationary exposures made to monitor the removal of cold work from the surfaces, each exposure was made with the specimen slowly translating and the film slowly rotating. In appropriate cases a thin layer of a standard metal powder, tungsten with cobalt radiation and silver with chromium, was dusted over a film of vaseline on the surface of the specimen to serve to calibrate the X-ray patterns. After the preliminary work, four films were made,

Jan 1, 1956

By J. Pinto, F. Galasso

THE current emphasis in preparing boron fibers by reduction of gaseous boron compounds on a resistively heated metal wire substrate has renewed interest in the borides of those metals which have relatively high melting points and are available as fine wires. A knowledge of the structures and properties of the borides, which are formed when boron diffuses into the metal core during boron deposition, can be of assistance in the understanding of the boron fiber formation process and the fiber properties. Many of these borides are well-known and their properties have been measured. However, when an unidentified boride is found in the core, it may be difficult to establish its composition because of the small amount of material available, the preferred orientation effects on the reflections in its X-ray pattern, and the possible overlap of X-ray reflections if several borides are present in the core. For example. the proper indexing of the X-ray pattern of WB4, which was formed in the tungsten substrate core during boron fiber formation, was accomplished only after small single crystals of this boride were grown and X-ray precession investigations were conducted.' This note presents the results of a study of the phases formed in the core when tungsten, tantalum, and molybdenum metal wires were used as substrates in the boron fiber preparation process with particular emphasis on the identification and characterization of a higher boride of molybdenum analogous to WB,. Boron was deposited on resistively heated stationary 0.0012-in.-diam tantalum, tungsten, and molybdenum wires at 1050°C for various times up to 60 sec using boron trichloride and hydrogen as the reactant gases. After 60 sec of boron deposition the fibers were approximately 0.006 in. in diam. Examination of photomicrographs of fiber cross sections showed that the boron had diffused nearly to the center of the tungsten and molybdenum cores in 15 and 30 sec, respectively, and only halfway to the center of the tantalum core in 60 sec. X-ray diffraction photographs of the fibers indicated that it was also after 15 and 30 sec deposition times that the tungsten and molybdenum metal reflections, respectively, had disappeared from the X-ray patterns of the fibers. The patterns of the boron fibers produced using tantalum wire as a substrate showed that amorphous boron, TaB2, and tantalum metal were present after a few seconds deposition time and remained even after deposition times of 60 sec. Until a deposition time of 15 sec was reached, the tungsten substrate fibers contained amorphous boron,273 6WB, W2B5, and WB4 as well as tungsten metal, while the molybdenum substrate fibers contained amorphous boron, MoBa, Mo2B5, and molybdenum metal for deposition times up to 30 sec. Just before the molybdenum metal pattern disappeared, a pattern similar to that of WB, appeared, suggesting that a phase, MOB,, isomorphous with WB,, was present in the fiber. This same pattern was obtained from the product formed by heating a mixture of molybdenum metal and excess boron powder in a boron nitride crucible at 1960°C in an argon atmosphere. As was the case with the WBn pattern, this pattern could best be indexed on the basis of a hexagonal unit cell rather than the tetragonal unit cell Chrktien and Helgorsky reported for ~0~4,~ see Table I. The unit cell parameters for MoB4 were calculated to be a, = 5.214A, co = 6.358A. Assuming the space group P63/mmc and positions5 2M01 in 2b and 2MoII in 2c found for tungsten in WB~,' a logical structure for MOB, was determined using geometrical considerations to place the boron

Jan 1, 1969

By A. L. Mincher, W. F. Sheely

Mechanical properties of columbium have been studied over the temperature range of -196 to 1093oC. The decreased strengthening influence of cold-work at temperatures below ambient has been interpreted in terms of the Peierls-Nabarro effect. Maxima in the rate of strain hardening observed during tensile testing in the range 250-600°C. have been correlated with interstitial impurities to indicate the temperature ranges at which carbon, oxygen, and nitrogen, respectively, are responsible for strain aging. THE growing need for structural materials for use above the useful service temperatures of the iron-, nickel-, or cobalt-base alloys has caused the refractory metals to be considered as potential engineering materials. These metals, which include columbium, tantalum, molybdenum, and tungsten, are called refractory because the lowest melting point among them,that of columbium, is about 1000°C higher than the average melting temperatures of conventional high-temperature alloys. They are all body-centered cubic transition metals and, as such, their mechanical properties have basic characteristics which distinguish them from the face-centered cubic metals. For example, all show a much steeper rise in strength with decreasing temperature below room temperature than do the face-centered cubic metals, and their mechanical properties are strongly influenced by interstitially dissolved impurities. In order that these new metals may be used efficiently, it is necessary that their characteristics of behavior be fully known. In this paper, the mechanical properties of columbium will be examined over a wide range of temperatures. In particular, the influences of cold-work and individual species of interstitial impurity atoms on mechanical properties will be described, and basic mechanisms which may control the observed characteristics will be explored. EXPERIMENTAL The material used in this investigation was Union Carbide Metals Co. columbium roundels consolidated to four 4-in. diam ingots, three by consumable-electrode arc melting and one ingot by electron beam melting. Impurity contents of the ingots and methods of ingot conversion and treatment are summarized in Table I. The only metallic impurity occurring in any significant quantity was tantalum at about 0.1 pct. Iron, silicon, titanium, and zirconium were each less than 0.015 pct; boron was 1 ppm or less. This should have no appreciable influence on properties. The electron beam melted material, being the purest, will be used as the basis for comparison in the discussions to follow. Tensile tests were conducted from-196 to 1093oC, on both cold-worked and fully recrystallized arc-melted and electron-beam melted columbium using standard 1/4-in. diam, 1-in. long gage length test specimens. A strain-rate of 0.005 in. per in. per min was employed until the 0.2 pct yield strength was achieved and then the strain-rate was increased to 0.05 in. per in. per min for the balance of the test. Samples were protected in an inert atmosphere at tests above 300°C. The tensile properties obtained on the electron-beam melted columbium, E, in both the cold-swaged and recrystallized conditions are given in Fig. 1. The yield strength data of Dyson, et al.,' obtained on recrystallized electron beam melted columbium and the tensile strength data reported by Tottle2 on powder metallurgy columbium are included in Fig. 1. The material used by Tottle had been purified by vacuum sintering. There is excellent agreement between Dyson's data and those obtained in the present investigation. The tensile strengths obtained by Tottle were slightly greater than those obtained in this investigation on electron-beam melted columbium but varied with temperature in a similar manner. Tottle's data showed a maximum in tensile strength near 500°C, as did our data on electron-beam melted material, and also showed a small maximum at 300°C. The significance of these maxima will become evident later in the discussion. The tensile properties of cold-swaged and recrys-tallized arc melted columbium are plotted in Fig. 2. It was found that the properties of the recrystallized arc-melted columbium from all three heats showed very close agreement except at temperatures between about 500" and 800°C. A reason for this range of disagreement will be suggested in the discussion. The generally good agreement, however, attests to the ability of cold-working and subsequent recrystal-lization to erase the effects of the three different primary breakdown procedures and to produce nearly equivalent structures in the samples derived from the three different heats. wesse13 reported tensile data on columbium having interstitial impurity contents between those of the

Jan 1, 1962

By Peter R. Morris

The effecl of preferred orienlation on X-vay dzffvaction measurements of retained austenzte was investigated for four precipitation-hardening staznless steels in sheet form. A method is preserzted for estimating the ervor in measurement associated with a given samplirig direction. The method was used to select an "optimum" sampling direclion in order to minimize errors in measurement due to preferred orientation. hleasuremenls of retained austenite content employing lhe proposed sampling direction are conzpaved to measuretnents enzploying the more commonly used normal direclion for a series of sawzples. THE first application of X-ray diffraction to the measurement of retained austenite in steels is due to Sekito, 1 who employed a photographic technique in which the (111) reflection from a thin strip of gold affixed to a cylindrical sample was employed as a standard. Averbach 2 introduced the "direct comparison" method in which the ratios of observed to calculated random intensity are assumed proportional to the austenite and/or martensite contents. Averbach's work forms the basis of most subsequent X-ray diffraction methods for the determination of retained austenite. Subsequent improvements are due to: Averbach and Cohen,3 who employed a sodium chloride crystal to monochromate cobalt radiation; Averbach et a1.,4 who introduced a bent sodium chloride monochromator; Mager,' who used a bent quartz crystal to monochromate chromium radiation ; Littmam, who first used a geiger counter diffractometer for this purpose; Beu and Beu and Koistinen, 11,12 who studied effects of absorption factor, surface preparation, sample geometry, integrated intensity vs peak height, choice of radiation, monochromator, and filter. The possibility of errors in measured values due to orientation effects was noted by Miller,13 who suggested examination of a surface other than the plane of rolling. Lopata and Kula 14 have developed an experimental technique in which the preferred orientation is measured in each sample. They illustrated the method for a sample containing 42 pct retained austenite. Application of their technique to the 1 to 15 pct range typical for the precipitation-hardening stainless steels does not appear feasible. EXPERIMENTAL PROCEDURE The nominal compositions of the precipitation-hardening stainless steels investigated are listed in Table I. Ingots were solution-treated, hot-rolled to approximately 0.2 in., and reduced to 0.050 in. by a suc- cession of cold rolling and annealing operations. After this treatment the 17-4PH sample was in the marten-sitic condition, while the 17-7PH, PH 14-8Mo, and PH 15-7Mo samples were in the austenitic condition. Samples of 17-7PH and PH 15-7Mo steels in the mar-tensitic condition were obtained by heating to 1750'F for 10 min and holding at -100°F for 8 hr. A sample of PH 14-8Mo steel in the martensitic condition was obtained by heating to 1700°F for 1 hr and holding at -100°F for 8 hr, followed by aging at 950" for 1 hr. POLE FIGURE DETERMINATIONS Samples were thinned to 0.003 to 0.005 in. by etching in a solution containing 250 ml reagent-grade phosphoric acid (85 to 87 pct H3PO4), 250 ml technical-grade hydrogen peroxide (30 to 35 pct H 2 O 2), and 50 to 100 ml reagent-grade hydrochloric acid (37 to 38 pct HCl). The specimens were placed in an "integrating" sample holder which provided a 1-in. oscillation in the plane of the sample. The diffractometer was aligned to measure the intensity diffracted by planes of the particular {hkl} type being studied. The sample was Set for a given latitude angle, a, measured from the plane of the sheet, and diffracted intensity recorded as the longitude angle, 0, measured in the plane of the sheet from the rolling direction, was increased from 0 to 360 deg. After a 360-deg scan of B, a was incremented by 5 deg, and the process repeated. Random standards obtained by spraying suspensions of powdered iron (bcc structure) and nickel (fcc structure) in lacquer were used to correct observed intensities for absorption and geometrical effects. Zirconium-filtered molybdenum radiation was used to determine the transmission regions of the (111) (0to 45 deg), (200) (0 to 60 deg), and (220) (0 to 45 deg) austenite and (110) (0 to 45 deg), (200) (0 to 50 deg), and (211) (0 to 35 deg) martensite pole figures. Vanadium-filtered chromium radiation was used to

Jan 1, 1968