Search Documents

By B. A. Eaton, K. E. Brown, C. R. Knowles, D. E. Andrews, I. H. Silberberg

This paper presents the resitlts of an investigation of two-phase, gm-liquid flow in horizontal pipelines. Experimental data were taken in three field-size, horizontal pipelines, two of which were constructed for this purpose. The data were obtained using water, distillate and crude oil separately as the liquid phase, and natural gas as the second phase. Experimental pressure-length traverse, liquid holdup and flow-pattern data were collected for each set of flow rates. These data were used to develop three correlations that are presented herein. The liquid-holdup values correlated with various flow parameters without regard to the existing flow pattern. The same was true for the energy-loss factors. A new flow-pattern map is presented that appears to be quite reliable, but not required for the pressure-loss calculations. The liquid-holdup correlation and the energy-loss factor correlation are used in conjunction with a two-phase flow power balance, developed during this study, to predict the pressure losses that occur during gas-liquid flow in horizontal pipelines. A recommended calculational procedure is given, as well as a statistical analysis of the results. This procedure lends itself to computer application, since several small pressure decrements are needed to calculate a pressure-length traverse. The correlations are shown graphically, but may be curve fitted with existing curve-fitring computer programs. INTRODUCTION Due to the frequent occurrence of gas-liquid flow in pipelines and the desire to accurately calculate the pressure losses that occur in these lines, two-phase flow is of considerable interest to the petroleum, chemical and nuclear industries. In the petroleum industry, gas-liquid mixtures have been transported over relatively long distances in a common line due to the advent of centralized gathering and separation systems. Long two-phase flowlines are usually accompanied by large pressure drops which influence the design of the system. Gas-lift installations are designed on the basis of known tubing pressures at the wellheads. The horizontal flowline connecting the wellhead and the separator system must be correctly sized in order to minimize the horizontal flowline pressure losses and the wellhead tubing pressure. Practically all oilwell production design involves horizontal two-phase flow in pipeknes. All of the flow processes of oil and gas production must be studied simultaneously to insure good well design. Since the beginning of offshore oilfield development, long horizontal flowlines have been constructed. Because pressure losses greatly influence the performance of producing wells, a method is desired that can be used to predict such pressure losses and select optimum flowline size. Several types of gas-liquid flow exist, and many of these are discussed by Gouse The study of pressure gradients, fluid distributions and flow patterns that occur in horizontaI multiphase flow is made difficult by the great number of variables involved. The various flow regimes give rise to changing velocities of the fluid particles in all directions. These instabilities of the interface between the gas and liquid prohibit the determination of actual vector velocities of fluid particles in each phase. Also, it is practically impossible to arrive at correct sets of boundary conditions. Therefore, most investigators have concluded that a solution to the problem by the classical fluid dynamics approach, whereby the Navier-Stokes equationsM are formulated and solved, is far too complex. Other methods must be utilized to develop general correlations that will predict the behavior of gas-liquid horizontal flow systems. Multiphase flow studies have sought to develop a technique with which the pressure drop can be calculated. Pressure losses in two-phase, gas-liquid flow are quite different from those encountered in single-phase flow; in most cases an interface exists and the gas slips past the liquid. The interface may be smooth or have varying degrees of roughness, depending on the flow pattern. Therefore, a transfer of energy from the gaseous phase to the liquid phase may take place while energy is lost from the system through the wetting phase at the pipe wall. Such an energy transfer may be either in the form of heat exchange or of acceleration. Since each phase must flow through a smaller area than if it flowed alone, amazingly high pressure losses occur when compared to single-phase flow. Most investigators of horizontal two-phase flow phenomena have chosen to separate their experimental data into several groups of observed flow patterns or regimes.

By F. C. Langenberg, J. Chipman

New data on the distribution of silicon between slag and carbon-saturated iron at 1600oand 1700oC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1700°C for slags containing up to 20 pct Al2O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A1203-SiO2 slags over a range from zero pct A12O3 to saturation with A12O3, or CaO.2A12O3. The upper limit of SiO, is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently, 4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/A12O3 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al2O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al2O3 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al,O3 and of A120,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO, (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2 The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

By F. E. Werner, B. L. Averbach, Morris Cohen

THAT bainite formed near the M, temperature bears a striking r esemblance to martensite tempered at the same temperature has been shown by the electron microscope.' By means of electron diffraction,' it has been established that carbide and cementite are present in bainite formed at 500°F (260°C); these carbides are also found in martensite tempered at 500°F (260°C).' The investigation reported here is concerned with an X-ray study of the matrix phases in lower bainite and tempered martensite. These phases have turned out to be dissimilar in structure; the matrix of bainite is body-centered-cubic while that of tempered martensite is body-centered-tetragonal. A vacuum-melted Fe-C alloy containing 1.43 pct C was studied. Specimens of 16 in. diam were sealed in evacuated silica tubing and austenitized at 2300°F (1260°C) for 24 hr. One specimen was quenched into a salt bath at 410°+7 °F (210°+4°C), held for 16 hr, and cooled to room temperature. The structure consisted of about 90 to 95 pct bainite, the re: mainder being martensite and retained austenite. A second specimen was quenched from the austen-itizing temperature into iced brine and then into liquid nitrogen. It consisted of about 90 pct martensite and 10 pct retained austenite. The latter specimen was tempered for 10 hr at 410°+2°F (210°+1°C). The specimens were then fractured along prior austenite grain boundaries (grain size about 2 mm diam) by light tapping with a hammer. Single aus-tenite grains, mostly transformed, were etched to about 0.5 mm diam and mounted in a Unicam single crystal goniometer, which allowed both rotation and oscillation of the sample. Lattice parameters were measured by the technique of Kurdjumov and Lyssak. This method takes advantage of the fact that martensite and lower bainite are related to austenite by the Kurdjumov-sachs orientation relationships Thus, the (002) and the (200) (020) reflections can be recorded separately, permitting the c and a parameters to be determined without interference from overlapping reflections. According to these findings, the matrix phase in bainite is body-centered-cubic and, within experimental error, has the same lattice parameter as ferrite (2.866A). On the other hand, martensite, tempered as above, retains some tetragonality, with a c/a ratio of 1.005t0.002. Most workers in the past have assumed that bainite is generated from austenite as a supersaturated phase, but the nature of this product has not been established. The question arises as to whether bainite initially has a tetragonal structure and then tempers to cubic, or if it forms directly as a cubic structure. If it forms with a tetragonal lattice, it might well be expected to temper to the cubic phase at about the same rate as tetragonal martensite. The martensitic specimen used here was given approximately the same tempering exposure, 10 hr at 410°F, as suffered by the greater part of the bainite during the isothermal transformation. About 50 pct bainite was formed in 6 hr at 410°F. On tempering at this temperature, martensite reduces its tetragonality within a few minutes to a value corresponding to 0.30 pct C.' Further decomposition proceeds slowly, and after 10 hr the c/a ratio is still appreciable, i.e., 1.005. Thus, even if the bainite were to form as a tetragonal phase with a tetragonality corresponding to only 0.30 pct C, which might be assumed to coexist with e carbide, it would not be expected to become cubic in this time. It seems very likely, therefore, that bainite forms irom austenite as a body-centered-cubic phase and does not pass through a tetragonal transition. The carbon content of the cubic phase has not been determined, but it could easily be as high as 0.1 pct, within the experimental uncertainty of the lattice-parameter measurements. It has been postulated that retained austenite decomposes on tempering into the same product as martensite tempered at the same temperature. There is now considerable doubt on this point. The isothermal transformation product of both primary and retained austenite at the temperature in question here is bainite," and the present findings show that bainite and tempered martensite do not have the same matrix. Acknowledgments The authors would like to acknowledge the financial support of the Instrumentation Laboratory, Massachusetts Institute of Technology, and the United States Air Force.

Jan 1, 1957

By Colin Baker, G. C. Smith

Investigation of the initiation and propagation of ductile failure in OFHC copper was undertaken to determine the role of nonmetallic inclusions. The effect of inclusion initiated voids on the formation of the internal cavity and the final shear separation was studied by metallographic eranzination of strained test pieces. A strain anneal technique was used to enlarge the voids under uniaxial stress conditions to elinzinate triaxial stress effects. Measurements of void size us stress and strain were made to show the point at which void im'tiation begins and becomes an important factor in the deformation process. The work of separation of copper-cuprous oxide was determined to attempt to correlate the breakdown of the matrix inclusion interface with void initiation and propagation. The zloid shape and position relative to the tensile axis suggested an interface breakdown mechanisnz of initiation. Evidence is presented that shows a basic similarity between the central cavity propagation and the 45-deg shear portions of the failure. DUCTILE fracture has been studied by a number of workers1-lo and attention drawn to the importance of hard second phase particles in the initiation of the failure. Holes formed at the matrix-particle interface can elongate by plastic deformation and then subsequently expand sideways to link up and produce a major crack. This is usually observed first in the center of the macroscopically necked region of a test-piece where the hydrostatic stresses are at a maximum. As the crack spreads sideways towards the free surface of the specimen, well defined shear zones develop from the crack tip and the final separation is along a direction at approximately 45 deg to the stress axis. This shear failure may also be associated with voids formed adjacent to second phase particles. In this way a cup and cone type fracture is produced. The stage at which separation takes place between particles and the surrounding matrix has not been clearly identified. In addition, although researchers have dealt with anisotropy of tensile behavior" as a result of material fabrication variables, not much is known about the microstructural features of aniso-tropic behavior. In the present work evidence on these points is presented in relation to the behavior of copper containing second phase particles of cuprous oxide. I. MATERIALS AND PROCEDURES EMPLOYED The material used was +-in. diam or 2-in. sq cold-drawn OFHC copper bar which contained 0.6 pct by volume of cuprous oxide inclusions. These ranged in COLIN BAKER, Junior Member AIME, formerly at -mnF of Metallurgy, University of Cambridge, Cambridge, England, is presently Research Scientist Reynolds Metals Co., Richrnand, Va. G. C. SMITH, Member AIME, is Senior Lecturer, Department of Metallurgy, University of Cambridge. Manuscript submitted June 20, 1967. IMD size from approximately 1 to 6 p in length and 1 to 4 p in width. The shape was generally slightly ovoid. Tensile tests were made on specimens having a gage length of 2.5 cm and diameter of 0.643 cm. Metallographic examination was carried out by sectioning deformed and fractured specimens; in addition fracture surfaces were examined optically and with a scanning electron microscope. Some measurements of the work of separation between copper and cuprous oxide were made, using a sessile drop technique which was a modification of that used by Kingery and umenick." The best metallographic results were obtained by using a vibratory polisher, which minimized smearing of the surface. 11. RESULTS A) Initial Experiments. Specimens from the +-in. diam rod were annealed for 2 hr at 650°C in uacuo, at which temperature complete recrystallization occurred without any change in the form of the inclusion. They were then fractured at temperatures from -190" to 600°C. Cup and cone fractures were obtained at all temperatures from -196" to 400°C. With increase in temperature there was, however, a continuous increase in the extent of the central transverse area and a corresponding decrease in the shear portion of the fracture. Above 400°C, the fractures became intergranular. Sections of specimens tested below 400°C revealed extensive small voids which were always associated with inclusions. However, the voids only reached dimensions greater than the inclusion size in the region of the macroscopic neck, where they were many times longer. Lateral expansion was found only near the fracture surface of the test pieces. As observed by Puttick, the voids were either (a) triangular holes initiated in the direction of the tensile axis and elon-

Jan 1, 1969

By E. F. Thomas

THE late George S. Rice was active in the inves--I- tigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and—to a lesser extent—Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,' if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable. Rice's system was put into operation in a mine in Harlan County, Kentucky,3 but subsequent experience has shown that it did not take into account two important factors—avoidance of pillar-line points and maintenance of adequate development in advance of the pillar-line abutment area. For ten years after Rice's retirement the USBM did little investigation and research on bumps, chiefly because so few were occurring that there was not much cause for alarm. But in 1951 there were three occurrences involving fatal injuries, and the Bureau began a statistical survey in that year. C. T. Holland, head of the department of mines at Virginia Polytechnic Institute, was retained as a consultant. The resulting study' of 117 case histories brought out these important conclusions: 1) Almost invariably the bump occurred in a locality affected by the abutment zones of one or more pillar lines. 2) In most cases the locality of the bump was influenced by the abutment zones of more than one pillar line. The term pillar-line point has been used for many years in the Appalachian region for such a situation. Point is used in the geographical rather than the mathematical sense. 3) In pillar-line extraction the following practices are safest in preventing bumps: a. The mine layout should provide for pillars of uniform size and shape along the extraction line. b. The mine layout should be planned so that no development need be done in the abutment zone of a pillar line. c. The layout should permit open-end extraction of pillar lines from the next goaf, so that it will not be necessary to resort to pocket mining, splitting pillars, or any practice that will involve driving in the direction of the goaf within the abutment zone. d. Pillars should be large enough to support area without undue roof and floor convergence before establishment of a pillar line. These are, of course, generalities, and while they are useful in laying out areas where bumps can be expected, they are of limited help in many mines that were committed to a system of mining before it was realized that they were subject to bumps. Under such conditions it becomes necessary to choose between the following alternatives: 1) Abandon the territory, except for pillars that offer no extraction problems. 2) Through experience select the pillars that are most heavily loaded, and, by augering, induce bumps from a safe vantage point so that impinged loads are relieved. This method was first developed at the Gary, W. Va. mines of U. S. Steel Corp. and later adapted to mining thick coal beds at Kaiser Steel's Sunnyside mine in Utah. No scientific method is available to determine where to drill within a loaded pillar. Although this method of unloading has worked very successfully at Gary—with one exception—

Jan 1, 1959

By R. F. Nielsen, D. E. Menzie

The object of this study was to determine if crude oil could be produced successfully by a process of crude oil vaporization using carbon dioxide repressuring. This process appears to have application to highly fractured formations where the major oil content of the reservoir is contained in the non-fractured porosity with little associated permeability. Crude oil was introduced into the windowed cell and carbon dioxide was charged to the cell at the desired pressure. A vapor space was formed above the oil, and the crude oil-carbon dioxide mixture was allowed to come to equilibrium. The vapor phase was removed and the vaporized oil collected as condensate. Samples of all produced and unproduced fluids were analyzed. Tests were also performed to evaluate the amount of vaporized oil that can he produced by rocking from a high to a lower pressure. The carbon dioxide repressuring process was applied to a sand-filled cell to investigate the performance in a porous medium. A test was performed to evaluate how the condensate recovery changes as the size of the gas cap in contact with the oil changes. INTRODUCTION This study has been directed toward a relatively new process of vaporization of crude oil designed to increase ultimate production of hydrocarbons through the application of carbon dioxide to an oil reservoir. Suggested advantages of carbon dioxide repressuring of a petroleum reservoir are: (1) reduction in viscosity of liquid hydrocarbons due to the solubility of carbon dioxide in crude oil, (2) swelling of the reservoir oil into a larger liquid-oil volume with a resulting increase in production and decrease in residual oil saturation due to an increase in the relative permeability to oil, (3) displacement of more stock-tank oil from the reservoir since the residual liquid is a swelled crude oil, and (4) gasification of some of the hydrocarbons into a carbon dioxide-hydrocarbon vapor mixture. Balanced against these advantages are several detrimental factors which must be evaluated; i.e., high compression costs and corrosion of well equipment and flow lines. Some of the more outstanding contributions to the study of carbon dioxide injection have been reviewed in order to furnish a basis for a continuation of research pertaining to this method. The literature reviewed1-8 has been limited to that dealing with carbon dioxide repressuring processes or with carbon dioxide-crude oil-natural gas phase behavior. Articles relating to carbonated water injection and literature published on the use of low pressure carbon dioxide gas injection in water flooding have not been included in this study. In 1941 Pirson5 suggested the high pressure injection of carbon dioxide into a partially depleted reservoir for the purpose of causing the reservoir oil to vaporize and thus produce the oil as a vapor along with the carbon dioxide gas. By reducing the pressure on this produced mixture of hydrocarbons and carbon dioxide at the surface, it was proposed to separate the hydrocarbons from the carrier gas. He theorized that essentially all the oil in a reservoir could be produced by simply injecting enough carbon dioxide to vaporize the residual oil. This present investigation deals with the vaporization of a crude oil by carbon dioxide, the molecular weight and gravity of the vaporized oil product and the characteristics of the residual oil after several repressuring cycles with carbon dioxide. An attempt is made to evaluate the merits of a vaporization process for the crude oil rather than a flow process where the oil recovery is determined by relative permeability considerations. Such a vaporization of crude oil by carbon dioxide repressuring appears to have possible use in a highly fractured formation where the major oil content of the reservoir is contained in the non-fractured porosity with little permeability. The carbon dioxide flows into the fractures, contacts the crude oil in the matrix and vaporizes part of the crude oil; this vaporized oil is produced and recovered and the carbon dioxide is reinjected again. The specific problem of this study is to attempt to answer this question; Can crude oil be produced successfully (technically, but without economic considerations) from a petroleum reservoir by a process of vaporization of the crude oil by carbon dioxide repressuring? DEFINITION OF TERMS AS APPLIED IN THIS STUDY Carbon Dioxide Contact: One cycle in which carbon dioxide was injected and bled off. Condensate: The hydrocarbon liquid which was condensed out of the mixture of hydrocarbon-carbon dioxide vapor upon reduction of the pressure of the vapor. Hydrocarbons Produced (HCP): All the hydrocarbon!, which were vaporized by the carbon dioxide repressuring process and were removed from the cell during any specific cycle or carbon dioxide contact. Hydrocarbons Unproduced (HCU): All the hydrocarbons which were not vaporized by the carbon dioxide

By H. G. Doll

A new electrical logging method. called MicroLaterology is described. whereby the resistivity R of the invaded zone close to the wall of the bore hole is measured. This method essentially utilizes a system of concentric circular electrodes iml,edded in an insulating support which is applied to the wall of the hole. A beam of current of very small diameter is focused horizontally into the formations by means of an automatic control device. and then opens widely at short distance from the wall. with this method, R most often can be recorded directly. except when the mud cake is very thick. in which case a correction is easily provided. The basic role of factor R in the quantitative analysis of electrical logs in terms of fluid saturation and of porosity is explained. The paper is illustrated with field examples. INTRODUCTION In electrical logging. the resistivity of that part of the penneable and porous formations which is invaded by mud filtrate is an important factor in the interpretation. Measurements made with the conventional devices — normal. lateral — and also with improved systems as the Laterolog and induction logging' — are very often more or less affected by the presence of the invaded zone. and the knowledge of the resistivity of this zone is useful in the evaluation of the true resistivity of the beds. which itself is a basic element for the determination of fluid saturation. Moreover. the comparison of the resistivity of the invaded zone with the resistivity of the mud filtrate gives valuable indications on the magnitude of the formation resistivity factor — which in turn is necessary for the quantitative interpretation of the logs. both in terms of fluid saturation and of porosity. On the other hand. it is generally admitted that the invaded zone is not a homogeneous medium separated from the uncon-tamirlated part of the bed hy a well defined cylindrical boundary. but that the fluid distribution—filtrate. connate water. hydrocarbon — and hence. the resistivity. in the invaded zone varies progressively with the distance from the wall of the hole. The term "resistivity of the invaded zone" therefore corre-sponds to an average value which is a function of the distribution of the fluids Inasmuch as the law of this distribution is not exactly known, the resistivity of the invaded zone is not a well defined factor. A much better definition is obtained if the medium under consideration is limited to that part of the formation which is within a short distance from the wall of the hole. It seems likely a within a distance of at least two or three in., most of the fluids in in the pores of tile formation have been displaced by the mud filtrate. The connate water has almost certainly been flushed out. and the oil. if any has generally been reduced to a comparatively small amount. The resistivity witliir~ the radial limit of two to three in. is. therefore. prac.tically constant at an). given level: its value. at least when the proportion of conductive solids in the formation is negligible. is chiefly dependent on the resistivity of the filtrate and on the porosity of the formation, and is affected only to a relatively small degree by the presence of the small amount of residual oil. This part of the formation close to the wall of the hole will he designated in the following as the "flushed zone." a-distinguished from the more general term of "invaded zone'. which relates to the part of the formation extending from the wall out to the distance where the formation is completely uncontaminated. The symbol R,, will he used for the resistivity of the flushed zone. (The notation R is related to the radial distance from the hole. If x designates this distance. xo is the initial value of x, i.e., the value corresponding to the region very close to the wall.) The determination of R is difficult, if not impossible. from logs made with the conventional devices. The long normal and the long lateral are. of course. not suited for this purpose because their radii of investigation are by far too large. The short normal. and the limestone sonde—-after correction for the effect of the hole hole — give resistivity values which corre. spond to materials situated within a comparatively short distance from the hole, but this distance is still several time. as great as the thickness of tire flushed zone. The only value which can be obtained with these devices corresponds to an average resistivity of the invaded zone- — and this only provided the invasion is deep enough, since otherwise the meas "red values would also be affected by the uncontaminated region beyond the invaded zone. It should nevertheless be recalled that despite these limitations. the measurements given by the short normal and or the limestone sonde are always very useful for qualitative interpretation. and also in favorable cases for the qantitative analysis of the logs in terms of saturation and porosity. The MicroLog. which was primarily developed for the detection of permeable beds and for an accurate determination of their boundaries. provides a good approach towards the evaluation of R. In the case of hard formation.. however. The

Jan 1, 1953

By A. S. Yue

The movphology of the Mg-32 wt pct Al eutectic has been studied as a function of freezing- rate and temperature gradient. At slow freezing rates a lamellar eutectic was formed; whereas, a rod-like eutectic was generated at fast rates. The inter-lamellar spacing increased as the freezing rate decreased in aggreement with theoretical predictions. Lamellar faults, morphologically similar to edge dislocation models in crystals, were responsible for the subgrain structures in the eutectic mixture. A linear increase in fault density with freezing rate was observed. Fault concentl-ations of the order of 10 per sq cm for a range of freezing rates from 0.6 to -3.0 x 10 cm per sec were estimated. The transformation from lamella?, to rod-like morphologies was determined experimentally to be dependent on the freezing rate and independent of the temperature gradient. Moreover, the number of rods formed per- unit cross-sectional area increased exponentiallv with increasing freezing rote. BRADY' and portevin2 classified eutectic structures into lamellar, rod-like, and globular according to the morphology of the solid phases present. Although this classification is quite descriptive, very little has been reported on the details of the mechanism by which the eutectic structures are formed. Recent work by Winegard, Majka, Thall, and chalmers3 and by chalmers4 on lamellar eutectic solidification suggest that the maximum thickness of the lamellae decreases with increasing rate of solidification due to inadequate time for lateral diffusion. scheilS and Tiller' have shown theoretically that the lamellar widths indeed depend on the solidification rate. However, there has been no experimental evidence to support the theory. Chilten and winegard7 have studied the interface morphology of a eutectic alloy of zone-refined lead and tin. They found that the lamellar width decreased as the freezing rate increased in agreement with the theoretical predictions of scheils and Tiller.' More recently, Kraft and Albright' have investigated the microstructures of the A1-CuA12 eutectic as a function of growth variables. They observed lamellar faults present in the lamellar eutectic, similar to edge dislocation models in crystals. Furthermore, Kraft and Albright reported that they could not designate which extra lamellar was responsible for the formation of a lamellar fault even under electron microscopic magnification. In this paper, the morphology of the Mg-A1 eutectic structure is described. The effects of freez- ing rate on the interlamellar spacing and on the lamellar fault density are presented in detail. The transformation from lamellar to rod-like eutectics is discussed in terms of the freezing rate and the temperature gradient. EXPERIMENTAL PROCEDURE The experimental details of alloy preparation, the decanting mechanism and the determinations of the freezing rate and the temperature gradient have been reported elsewhere. Measurements of plate-edge angles were made with a microscope. The true angles used to determine the interlamellar spacings were determined by a two surface analysis technique.'' Since the decanted interface structure does not represent the true eutectic morphology on the solid,g all measurements were made from an area in the solidified bar behind the interface. Measurements of the apparent interlamellar spacings between the two phases of the eutectic were made on a photographic negative by means of a calibrated magnifier. Each value listed in Table I represents the average of thirty measurements on one negative. In general, these measurements are approximately equal with an error of less than pct. The average rod diameter for each specimen was also measured on a magnified photomicrograph. Each value of the diameter represents the average of fifty measurements. RESULTS AND DISCUSSION The experimental observations and their discussion to be presented here are restricted to the morphology of the eutectic structure and to the effects of the freezing rate and the temperature gradient on the solidification of eutectics. INTERLAMELLAR SPACING It has been shown previouslyg that the micro-structure of the decanted interface and the longitudinal section of the Mg-A1 eutectic is characterized by the presence of both lamellar and rod-like morphologies. The lamellae become more regular as the freezing rate is decreased. A three-dimensional photomicrograph representing a perfect lamellar morphology is illustrated in Fig. 1. The lamellae of the top and longitudinal sections of the specimen are regularly spaced while those in the transverse section are not quite straight and parallel. Their parallelism is slightly distorted because fault lines producing a discontinuity are present. A method for calculating the interlamellar spacings A, is described in Appendix 1. The true

Jan 1, 1962

By G. Borelius

ABOUT the turn of the century, Gibbs' thermo-dynamic theory of heterogeneous equilibrium, on the one hand, and the experimental methods of thermal and microscopic analysis, on the other, gave to the physical metallurgist his first scientific tool, the equilibrium diagram. The classical equilibrium diagram of a binary alloy system shows the boundaries between ranges of homogeneous and heterogeneous equilibrium in their dependence of concentration and temperature. A homogeneous solid sohtion which on cooling passes such a boundary is assumed to precipitate, forming a mixture of two phases with different concentrations. The equilibriunl diagram and the equilibrium theory, however, give no information about the time scheme of the process or the intermediate states passed during precipitation. For this reason it satisfies neither the practical need of the metallurgist nor the curiosity of the physicist. As a matter of fact, in the heat treatment of alloys for technical use the objective very seldom is the equilibrium state. Thus good mechanical properties of construction material are connected, for the most part, with some intermediate state. As these intermediate states are thermodynamically unstable, there is, from a theoretical point of view, always to be expected a decay of the good properties with time; and it is a matter also of practical interest to know whether this natural life time of a material is of the order of, say, ten or thousands of years. Thus, for many reasons, there is a current demand to complete our knowledge of equilibrium through knowledge of the kinetics of the precipitation phenomena. From the point of view of the physicist, the most interesting question in this case is whether there are any general laws governing the kinetics. According to a generally accepted view, precipitation is ruled by two more or less independent phenomena, the formation of nuclei of a new phase and the growth of these nuclei. It is also commonly accepted that there is a tendency for the velocity of growth to increase with increasing temperature because of the increasing mobility of the atoms. There is also a tendency for the velocity of growth to decrease in the neighborhood of the two-phase boundaries. So far, however, very little is known quantitatively about this fundamental phenomenon in the case of solid metallic systems. In our laboratory attention has been directed especially toward the nucleation phenomena, and a series of measurements have been carried out with the guidance of a work- ing hypothesis (based on experiences from previous work on order-disorder transformations in alloys) about the influence on the nucleation of thermo-dynamic potential barriers. However, before discussing the experiments, the theoretical ideas will be considered. In a binary solid solution the arrangement of atoms on the lattice points approaches with increasing temperature a state of full randomness, as illustrated by the ball model of Fig. 1, that might represent a [111] plane of a face-centered alloy with 30 pct "black" and 70 pct "white" atoms. In reality the atoms are changing places continually with their neighbors so that the picture should rightly have been a moving one. On account of this thermal motion the concentration of black atoms within a certain group of, say, a hundred or a thousand lattice points fluctuates with time around the bulk concentration of 30 pct in a manner governed by statistical laws. With decreasing temperature two independent changes in this state grow more and more important. First, the mobility of the atoms decreases, and second, the forces between the atoms will have an increased influence on the fluctuations. In alloys with a tendency for precipitation, which are the concern of this lecture, the distribution function of concentration fluctuations will broaden, so that the relative probability of great local variations from the bulk concentration increases. Fig. 2 gives an example of such a fluctuation. When the alloy is supercooled below the solubility limit into the range of two-phase equilibrium, the fluctuations will now and then at some point give rise to a state that resembles the equilibrium state and thus will form a stable nucleus that is capable of growing by diffusion processes. In discussions with colleagues and in the literature, I have often encountered the idea that three or four atoms of the dissolved metal could form a nucleus of the new phase. A look at the ball model might be enough to indicate that this cannot be true. If it were true, there should be nothing but nuclei, whereas we know from experiment that nucleation must be a rather rare occurrence. In fact we have, as will be mentioned later, certain reasons to believe that the nuclei are formed by fluctuations containing some hundreds of atoms, which should be the order of the number of black balls in the fluctuating group of the figure, if it were extended into three dimensions. As a working hypothesis we have assumed that the fluctuations producing nuclei, though large and rare, still are ruled by the distribution laws of fluctuations of the supercooled solid solution in its initial state. Thus the probability of nucleation will be connected to the thermodynamic properties of the solid

Jan 1, 1952

By J. W. Edington

THE Hopkinson bar has become a popular technique for the measurement of the mechanical properties of materials deformed at high strain rate. Maximum use of the equipment is made in the arrangement first used by Kolskyl in which a short compression specimen is sandwiched between two pressure bars and is loaded by a single pulse travelling through the system. The pressure bars are used both to apply the load to the specimen and as transducers to obtain continuous strain-time histories of three pulses, incident on, reflected, and transmitted by the specimen. The data measured by the pressure bars can be analyzed in terms of the stress/strain behavior of the specimen.2'3 However, one of the assumptions of the analysis of the observed pulses is that the total stress and total strain do not vary significantly from point to point within the specimen at any given instant during the deformation process. Although this assumption is generally justified for very short disc-like specimens2 the situation is uncertain for larger specimens. For example, at small plastic strains (-0.01) Hauser et al.2 have some evidence of small flucations in the total stress within the crystal during deformation, even in relatively short aluminum specimens. In addition, Karnes4 has shown that the plastic strain, and by inference strain rate, is different at each end of a compression specimen tested in a Hopkinson bar, although the length of the specimen was not specified. Recently, the mechanical properties and the dislocation substructure have been investigated in single crystals of columbium5 (length 0.25 in., diam 0.19 in.), and copper6 (length 0.5 in., diam 0.5 in.) deformed at high strain rates. As part of this research program the assumption that the plastic strain is constant throughout the specimen has been checked by measuring the total dislocation density as a function of position in the specimen. Compression specimens of the same orientations and dimensions were tested as described previously5,6 sing a split Hopkinson bar. Since any discontinuity in strain distribution is most likely to arise during the initial stages of deformation the investigation was performed on specimens deformed to plastic shear strains of 0.054 (copper) at a strain rate 1.2 x l03 sec-1, and 0.06 (columbium) at a strain rate 1.5 X l03 sec-1. The orientation of the single crystals is shown in Figs. 1 and 3. Thin foils were taken parallel to the most highly stressed slip plane, i.e., (111) in copper and (011) in columbium, using conventional disc techniques. The dislocation densities were measured using first order reflections with compensation for invisible dislocations.5'6 In the copper single crystals the discs were randomly distributed throughout the cross section of the specimen. However, the dislocation density obtained from each disc was plotted vs the disc positions relative to the ends of the specimen. The results for the copper specimens are shown in Fig. 1. Clearly the dislocation density is constant throughout the main portion of specimen within the experimental error. The error bars on the dislocation densities correspond to a shear strain variation of 0.015 on the basis of previous measurements% ± of the rate of increase of dislocation density with strain in copper single crystals of the same geometry. Thus within this experimental error the plastic strain can be concluded to be constant within the specimen and the assumptions used in the analysis of the stress/time curves are therefore reasonably valid. The higher measured dslocation density near the impact end and the lower dislocation density at the bar end of the copper specimen is in agreement with the results of Karnes4 who showed that this strain/time curve rose to a maximum more rapidly at the impact end compared with the bar end. Hauser et al.2 have also pointed out that at small plastic strains (-0.01) the strain at the impact end of the specimen may be greater than that at the bar end. Thin foils taken from different points within the columbium single crystals demonstrated that the dislocation density could vary significantly within the specimen, see Fig. 2. Large areas of some thin foils up to 30 µ sq contained very few dislocations, see Fig. 2(a). However, in other parts of the compression specimen dislocation configurations like those shown in Fig. 2(b) existed over large areas (-30 µ sq). As a result, when the average dislocation density in a thin foil is plotted as a function of the position of the thin foil relative to the ends of the specimen, considerable scatter is observed, see Fig. 3. In this material then, the local dislocation density, and consequently the

Jan 1, 1970

By E. S. Tankins, G. R. Belton

A simple solution model, based upon the formation of molecular species, is developed for strongly electronegative dilute solutes in liquid binary-metallic solvents. Two approximations are considered for the relative concentrations of the species: the random and the quasi-chemical. Equations are presented for the partial molar free energy, enthalpy, and entropy of mixing of the solute. An experimental study has been made of equilibrium in the reaction H2 6) +0 (dissolved) = H2O(g))for the liquid Cu-Co alloys. The standard free energy of solution of oxygen is presented as a function of composition for the alloys at 1550°C and as a function of temperature for five of the alloys. The experimental results for these alloys and also for Cu-Ni alloys are shown to be in reasonable agreernent with the theory in the random approximation. A knowledge of the thermodynamic behavior of dilute solutes in liquid metals and alloys is of importance in understanding and designing refining and alloy-making processes. Accordingly, several attempts have been made to derive suitable solution models to forecast the effect of a third component on the activity coefficient of such a solute in a metal. Alcock and Richardson' reviewed the literature prior to 1958 and also showed that a regular solution model gave a reasonable description in the case of metallic solutes but failed to account for the behavior of the more electronegative solutes sulfur and oxygen. These same authors2 later modified their model by using the quasi-chemical approximation3 to calculate the average composition of the first coordination shell surrounding each solute atom. This modified model was shown to lead to a better qualitative description of the behavior of the electronegative solutes; however, quantitative agreement with experimental data for oxygen in alloys could only be achieved by assuming a very small coordination number. The authors concluded that the major source of error in the model was the assumption that pairwise interaction energies were independent of composition. Substitutional and interstitial random solution models by Wada and saito4 are essentially similar to the first model except that the required interchange energies were derived from the modified solubility parameter equation of Mott, instead of from experimental binary data. Most recently Hoch5 has presented a statistical model for interstitial solutions and has applied the model to the Fe-C-O system. However, as the various interaction energies needed in the model had to be derived from the ternary data, the model does not promise well as a means of forecasting ternary behavior. Each of the above models carries the assumption that the strongly electronegative solutes have the same configurational environment as metallic solutes; i.e., the solute can be treated as a substitutional or interstitial atom in a quasi-crystalline lattice and is surrounded by a normal coordination shell of solvent atoms. There are, however, a number of facts which suggest that this is unlikely. First, the heats of solution are large, being more typical of molecule formation rather than alloying. For example, the heats of solution of monatomic oxygen and sulfur in liquid iron are -90 kea16,8 and -74 kea1,7, 8 respectively. These are to be compared with maximum heats of solution of metallic solutes in liquid iron of about -13 keal (silicon is an exception with -28.5 kea17). The large depression of the surface tension of liquid iron by trace amounts of the electronegative solutes oxygen, sulfur, and selenium9 suggests, by analogy with aqueous systems, the possible existence of polar molecules in the liquid. The effect of these solutes is at least three orders of magnitude greater than normal metal solutes.10 As has been pointed out by Richardson,11 the electron affinities and ionization potentials of oxygen and sulfur are such that it is likely that they exist in metallic solution as negatively charged ions. If this is so, and it is assumed that electrostatic forces play an important role in determining the configuration, it is unlikely that the stable configuration will be that of an isolated ion surrounded by a symmetrical coordination shell of solvent ions. It is more likely that the energy of the system would be lowered by the formation of solute-solvent screened dipoles. The above arguments suggest the formation of "molecular species" between solute and solvent atoms. The idea of the existence of molecular species in such solutions is not new, however', for Marshall and chipman12 have explained in a semi-quantitative manner the C-O equilibrium in liquid iron by postulating the species CO. Chen and Chip-man13 interpreted their measurements on the Cr-O equilibrium in iron in terms of the species CrO. Zapffe and sims14 have also postulated the existence of such species in liquid-iron alloys.

Jan 1, 1965

By Allan Martin, R. A. Swalin

Diffusion rates of manganese, aluminum, titanium, and tungsten in nickel were measured at temperatures between 1100° and 1300°C. Activation energies, Q, and values of the frequency factor, Do, were calculated for each system. Values of Q were found to be within 15 pet of that for self-diffusion of nickel in agreement with present theories of diffusion. ONE of the most interesting problems in diffusion concerns factors governing the order of diffusion coefficients of various solutes in a common solvent metal at low solute concentrations. An early suggestion by Rhines and Mehl' was that diffusion coefficients might each approach that of the self-diffusion coefficient of the solvent itself. Later Thomas and Birchenall' pointed out correlations between the order of the diffusion coefficients and the freezing point depressions of the solvent by the various solutes. Other correlations have been sought. To settle this question it seems likely that much more data will be needed and, in particular, data collected at low solute concentrations. This type can be obtained by special analytical techniques as well as by use of radioactive tracers. The following study was made of diffusion of manganese, aluminum, titanium, and tungsten in a common solvent, nickel, at relatively low solute concentrations: 1—Production of alloys of nickel with manganese, aluminum, titanium. and tungsten at concentrations of the order of 1 atomic pet. 2—Use of pressure-welded diffusion couples in cylindrical form. 3—Diffusion anneals in the temperature range of 1100" to 1300°C. 4—Lathe sectioning of the diffused couples. 5—Spectrophotometric analyses of lathe turnings for the solute being studied. 6—Calculation of the diffusion coefficient for each of the solutes as a function of temperature. 7—Interpretation of results with current theories of diffusion. Experimental Work Materials—Two types of nickel were used in this research. The grade designated as Vacuum melted Mond nickel was used for all diffusion systems except the Mn-Ni system for which the Vacuum melted electrolytic nickel was used. Analyses of the two grades are given in Table I. The manganese used in making alloys was 99.9 + pet pure, aluminum 99.99 pet pure, titanium 99.9 pet pure, and tungsten of C.P. grade powder. Alloys used in this investigation were prepared by melting in vacuo or under a low pressure of argon. After melting, all heats except those of nickel-manganese were poured into a cylindrical copper mold 3 in. long and 1 in. ID. In the case of nickel-manganese, the alloys were solidified in the melting crucible. For nickel-aluminum heats alumina crucibles were used and for all other heats, zirconia crucibles.

Jan 1, 1957

By J. D. Livingston

THE hardening of alloys by the precipitation of a second phase has long been an important technological process. One approach towards improving our understanding of this phenomenon has been a correlation of mechanical properties with such parameters as particle size and inter par ticle spacing.' Several reviews of such data have appeared.2-4 A major limitation to this approach has been that for most alloys the particles are submicroscopic in size in the range of optimum hardness. Precipitation-hardening copper-cobalt alloys, therefore, are of interest, because the ferromagnetic properties of the precipitate make it possible to measure particle size, number of particles, and so forth, from magnetic measurements alone.5, 6 Livingston and Becker7 have applied these techniques to a study of precipitation hardening in an alloy of 2 pct Co in copper. It was found from magnetic measurements that nearly all the cobalt to be precipitated was out of solution within a few minutes at 600°C, whereas the peak in tensile yield stress was not attained until a much longer aging time. Thus during the first 1000 min of aging time at 600°C the Yield stress was increasing while a constant volume of precipitate was coarsening, i.e., while particle size and interparticle spacing were increasing. Peak yield stress was reached at an average particle radius of about 70A. The earlier study was confined to one alloy at one aging temperature, so that the volume fraction of precipitate was fixed and, therefore, particle size and interparticle spacing could not be independently varied. The work has now been extended to several alloys of varying percentage cobalt in copper, and to aging at various temperatures. It was hoped that such a study might clarify the relative importance to precipitation hardening of particle size, interparticle spacing, and volume fraction of precipitate. EXPERIMENT The alloys studied contained 0.7, 1.3, 2.0, and 3.2 wt pct Co in copper. They were prepared from electrolytic copper and electrolytic cobalt in a vacuum -induction furnace, worked to 3/8-in.-diam rod, and machined into tensile specimens with a gage section 1 1/2 in. long and 3/16 in. in diam. All specimens were given a solution treatment consisting of a 30-min anneal in nitrogen at 1000° C followed by a quench into iced brine. Subsequent aging was done in nitrogen and followed by a water quench. Average grain diameter was approximately 0.01 in.

Jan 1, 1960

By Elmars Ence, Harold Margolin

The partial isothermal section of the Ti-Cu-Zr system at 750°C has been studied. The crystal structure of Ti2Cu has been detevnlined as tetragonal and when expressed as face-centered tetragonal, a = 4.164, c = 3.611 A, and c/a = 0.867. TITANIUM systems in which ß-titanium decomposes eutectoidally into a and a compound rather readily are known as active eutectoid systems. Recently in active eutectoid alloys based on the Ti-Cu system, and containing additionally A1 and Zr, it has been found that zirconium may produce both moderate weakening and marked strengthening at elevated temperatures.' In order to obtain some insight into the behavior of zirconium, an attempt was made to determine whether compounds of the type Tix Zr and TixZryCu exist. Only results of the Ti-Zr-Cu studies are reported here since data on Ti-Zr alloys will be presented in a separate publication. EXPERIMENTAL PROCEDURE Alloys were nonconsumably arc melted in argon atmosphere as 15-g buttons, prepared from materials of the following purities: Bureau of Mines electrolytic Ti — Bhn 63 OFHC copper Reactor Grade Zirconium Bhn .C 150 Prior to alloy preparation the electrolytic titanium was premelted to avoid excessive spattering of the charges during melting. The weight losses during melting did not exceed 1 pct of the total weight of the charge. The alloys prepared are listed in Table I together with analyzed compositions. in cases where they were determined. Specimens for heat treatment were wrapped in molybdenum sheet, annealed in argon-filled quartz capsules, and quenched by breaking the capsules under iced brine. About 1 to 2 sec are required to remove the capsule from the furnace, drop it into the iced brine and break it. Because of the insulation effect of the quartz, this delay in quenching should not produce a large drop in temperature. In many instances, no difference or little difference has been detected between the same specimen quartz capsule quenched or directly quenched in vacuum by an impinging stream of water.' Ti-Cu-Zr alloys were homogenized for 48 hr at 825°C prior to annealing at 750°C. Annealing for 5 days at 750°C produced the same results as 11 days at temperature and it was therefore assumed that 5 days was sufficient to establish equilibrium. Titanium-copper alloys were homogenized for 40 hr at 900°C prior to heat treatment for 6 days at 750°C. Specimens for metallographic examination were electropolished and etched with the following solution:

Jan 1, 1962

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, Shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, Shall preside. If none of these be present the meeting Shall elect a Chairman. The President Shall do and perform Such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. IL ORDER OF BUSINESS. At each business meeting of the Institute the order of business Shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment Shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary Shall keep a record of the proceedings of all the meetings of the Institute. He Shall be custodian of the corporate Seal, of the minute books and of all the legal documents belonging to the Institute. He Shall have charge on behalf of the Institute of all correspondence. He Shall notify all Officers and Directors and all members of committees of their election and appointment; Shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and Shall, in calling Special meetings of the Directors, Specify the objects of Such meetings. He Shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary Shall be custodian of all technical or Scientific papers Submitted to the Institute for its consideration and Shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and. of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There Shall be kept under his direction an account

Jan 1, 1925

By B. N. Das, J. B. Darby, P. A. Beck, Y. Shimomura

A POWDER pattern for the (Cr, Mo, Co)R-phase annealed at 1200°C was reported in 1951.1 Through the courtesy of Prof. D. P. Shoemaker of Massachusetts Institute of Technology the authors became aware of inconsistencies of this pattern with that to be expected from the structure of the R-phase, as determined by Komura, Shoemaker, and Shoemaker.' In addition, Professor Shoemaker also noted that the powder pattern reported8 for the (Cr, Mo, Co)D-phase, annealed at 1300°C, agreed fairly well with that to be expected from the newly determined structure of the R-phase. In view of these findings, the previously reported powder patterns of the R-phase and of the D-phase were compared carefully. It was found that most lines in the two patterns (22 lines) were to a fair degree of accuracy related to each other by a single conversion ratio for the corresponding d spacings. The value of the conversion ratio was found to be 1.0058, so that the d spacings of the D-phase pattern previously reported were larger than the correspond- ing d spacings for the reported R-phase pattern by approximately that factor. The intensity relationships between corresponding lines in the two patterns were similar, as judged visually. The following exceptions were noted: Lines Nos. 2, 3, 19, 20, 21, 22, 23, 24 and 25 of the D-phase pattern,:' all designated weak or very weak, were missing in the apparently somewhat fainter R-phase pattern used.' Lines 1, 2, 3, 5, 15 and 34 (all weak or very weak), reported for the R-phase, were missing in the D-phase pattern, Table I. In view of these observations it seemed probable that the two patterns differed from each other mainly by a slight change in lattice parameters (with c/a remaining approximately constant), and that the pattern previously reported for the R-phase contained some weak extraneous lines, most likely to be attributed to impurities. In order to check the foregoing assumption, two specimens of an alloy containing 43 pct by weight of cobalt, 41 pct molybdenum, and 16 pct chromium, which was within the composition range of stability of both the D-phase at 1300°C and of the R-phase at 1200°C, were homogenized at 1200 and 1300°C, respectively, and quenched. X-ray diffraction patterns of the powders of these two specimens, obtained with CrK radiation, were compared carefully with each other and with the D-phase pattern previously

Jan 1, 1959

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, shall preside. If none of these be present the meeting shall elect a Chairman. The President shall do and perform such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. II. ORDER OF BUSINESS. At each business meeting of the Institute the order of business shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary shall keep a record of the proceedings of all the meetings of the Institute. He shall be custodian of the corporate seal, of the minute books and of all the legal documents belonging to the Institute. He shall have charge on behalf of the Institute of all correspondence. He shall notify all Officers and Directors and all members of committees of their election and appointment; shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and shall, in calling special meetings of the Directors, specify the objects of such meetings. He shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary shall be custodian of all technical or scientific papers submitted to the Institute for its consideration and shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There shall be kept under his direction an account

Jan 1, 1925

By H. C. Lukens, E. V. Potter

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

By E. V. Potter, H. C. Lukens

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, shall preside. If none of these be present the meeting shall elect a Chairman. The President shall do and perform such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. II. ORDER OF BUSINESS. At each business meeting of the Institute the order of business shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary shall keep a record of the proceedings of all the meetings of the Institute. He shall be custodian of the corporate seal, of the minute books and of all the legal documents belonging to the Institute. He shall have charge on behalf of the Institute of all correspondence. He shall notify all Officers and Directors and all members of committees of their election and appointment; shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and shall, in calling special meetings of the Directors, specify the objects of such meetings. He shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary shall be custodian of all technical or scientific papers submitted to the Institute for its consideration and shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There shall be kept under his direction an account

Jan 1, 1925