Search Documents

By J. R. Long, R. S. Dean, D. C. Root, E. T. Hayes

The U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities1 and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriatc applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately- applicable. While atomic: hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-are methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1947

By Benjamin Lustman, Robert F. Mehl

THE study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation-i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from o to 1000-2000 Angstroms-has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difference may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations. 3,4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 EXPERIMENTAL PROCEDURE Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and reproducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900º to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal.

Jan 1, 1941

By Helmut Thielsch

DURING the last three decades a great many arguments have been presented on the subject of "mosaic" or "block" structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner structure of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as plasticity, ferromagnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals, the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because of the vast extent of the field of submicroscopic structures, it shall be the purpose of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic pattern f and effects of cold reduction and recrystallization will be shown in further studies later on. IMPERFECTIONS IN CRYSTALS The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. Ideal, or Perfect Crystals.-Crystals without any structural imperfections are called "ideal crystals," or "perfect crystals," meaning a homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.-" Real crystals"' may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities existing in these groups mean that the orientation of the crystallographic axes will not be the same at every point within the interior of a crystal (or grain of a polycrystalline body). Perfect Real Crystals.-The term "perfect real crystals" is generally used to describe crystals with minute structural or thermodynamical inhomogeneities. The former

Jan 1, 1945

By M. I. Jacobson, M. L. Hammond

The solid solubilities of high-purity silver, aluminum, chromium, copper, and iron in zone-refined beryllium have been determined. Diffusion couple sandwiches of beryllium with aluminum, copper, and silver foil and diffusion couples of beryllium with two-phase alloys in the Be-Cr. Be-Fe, and Be-Ag systems were analyzed by electron beam micro-probe techniques. This paper describes the material used, the experimental methods for preparing the diffusion couples and the alloys, the analytical techniques, and the results obtained. The results are compared with those of previous investigators who used materials of lower purity. ~NVESTIGATORS of beryllium phase diagrams have often been hampered in their interpretations of certain phase boundaries because of the relatively low purity of the beryllium used. This has sometimes resulted in the appearance of three phases in the regions where only two should exist. Advances in purification methods, specifically zone refining, have made available beryllium that is considerably purer than the material previously used for phase diagram studies. The primary object of this investigation was to reex-amine portions of the beryllium-rich end of the binary systems of beryllium with silver, aluminum, chromium, copper, and iron to determine more accurately the limits of terminal solid solubility. The five elements—silver, aluminum, chromium, copper, and iron—include some which are commonly found as the major impurities in beryllium, some of which are being used as solid-solution alloying elements, and some of which are used in ductile matrix alloys. They are thus of considerable importance to physical metallurgists who must work with beryllium but who must rely on the present inaccurate or incomplete diagrams. The determination of more reliable diagrams would aid researchers concerned with the problems of alloying, heat treatment, and ductility. MATERIAL The beryllium was acquired from the Franklin Institute in the form of a single-crystal, 6 in. long by 1 in. in diam, zone-refined in three passes from Pechiney SR-grade beryllium bar. The principal impurities, as determined by mass spectrography at Battelle Memorial Institute, are shown in Table I. Vacuum-melted copper, silver, and aluminum, and electron-beam zone-refined iron were obtained from the Materials Research Corp. in the form of 1/2-in.- diam bars. Iodide chromium was obtained as flakes from the Chromalloy Corp. Analyses supplied with these metals are shown in Table 11. EXPERIMENTAL PROCEDURE Preparation of Diffusion Couples. Two types of dif-fusion couples were used in this study. For the copper, silver, and aluminum systems, the couples were sand-

Jan 1, 1969

By S. Y. Ogawa

The effects of sulfur (up to 0.1 pet) on the deformation and fracture characteristics of iron, in cast form, were studied at strain rates up to 100 pct pcr sec and at temperatures of 1600o to -3300 oF. The effects of oxygen and manganese additions on the behavior of Fe-S alloys were studied under comparable test conditions. Brittle fracture characteristics, evident at all strain rates, resulted from the presence of the liquid iron sulfide phase at grain boundaries. Ductility could be restored in three ways: solution of the sulfide in solid y iron at higher temperatures, spheroid-zzation of the liquid sulfide, and increase. in the melting point ot the sulfide. THE literature shows that most previous studies of deformation and fracture at hot working temperatures have been based on measurements of energy absorption, reduction of height in forging upset tests, torsion tests of bar or wire samples, and so forth,' but that relatively few tension tests have been used at high temperatures and strain rates. The present work was initiated to study the ef- fects of temperature, strain rate, composition, and structure on the deformation and fracture characteristics of iron, utilizing cast specimens tested in tension. As in a previous study,' strain rates up to 100 pct per sec were chosen for the temperature range 1600° to 2400° to provide data which might be useful in the interpretation of the deformation and fracture behavior of steels under hot working conditions. The previous work was with Fe-P solid solution al10ys;2 this work is concerned with Fe-S alloys, and with the effects of oxygen and manganese additions. MATERIALS AND PROCEDURE Cast tes! specimens were employed throughout, since most of the difficulty during hot working occurs in the initial breakdown of the ingot. Alloy Systems. Ten 25 lb. heats containing sulphur were prepared. Of these, three had manganese additions, and two had oxygen additions. The sulfur content varied from 0.023 to 0.10 pct. Manganese contents were intended to be ten to twenty times the sulfur content of the particular alloy. Oxygen, being more difficult to control in small melts, was varied by the amount of solid deoxidizer added, but poor control of the oxygen content was experienced in most instances. Table I shows the chemical analyses of the heats. Melting and Casting. Electrolytic-iron chips were melted by high frequency induction in a prefired, clay-graphite crucible lined with rammed magnesite.

Jan 1, 1962

By M. J. Pool, P. J. Spencer, J. R. Guadagno

THE present work was carried out as part of a general program to study the magnitude and concentration dependence of exothermic heats of solution of various metals in liquid tin. Thermodynamic data for the Te-Sn system are very limited, particularly for dilute alloys. Indeed, apart from the prior heat of solution determinations of Pool,1 the only other published values are those of McAteer and seltz2 who carried out electromotive force measurements on solid alloys of compositions from 75 to 95 at. pct Te at temperatures between 543° and 668° K, of Colin and Dro-wart3 who made mass-spectrometric studies of the vapor in equilibrium with solid SnTe, and of Robinson and Bever4 who determined the heat of formation of SnTe by solution calorimetry. The present work thus provides further thermodynamic information for this system, specifically in a temperature range where the solubility of tellurium is very limited. The liquid metal solution calorimeter used in this investigation has been described previously.' No further discussion of its design or operation will therefore be given here. For each series of measurements a tin bath consisting of approximately 70 g of 99.99 pct pure Sn was carefully weighed out and inserted in the calorimeter which was maintained at the desired temperature to within ± 1/4°c. Tellurium, of 99.999 pct purity, was supplied by Atomergic Chemetals Co., a division of Gallard-Schlesinger Chemical Manufacturing Corp. Approximately 0.0006 to 0.001 g-atom specimens of tellurium were used for each experimental run and these were added to the calorimeter from a temperature of 273" K. Heat of solution values were calculated by analysis of a strip-chart recorder plot of the heat effect accompanying the solution of each sample in the tin bath. The heat capacity of the latter was determined at regular intervals during a series of tellurium drops by using pure tin or tungsten calibration samples, the heat contents of which were obtained from the standard compilation of Hultgren et al5 The composition of the bath was calculated after each drop from a knowledge of the weights of tin and tellurium added. Values of the heat of solution of tellurium at 725" and 775° K are listed in Table I together with the corresponding tellurium contents of the alloys. The data are also plotted as a function of tellurium concentration in Fig. 1, which includes the equivalent data obtained by pool' at 750° K. It can be seen that the heat of solution remains

Jan 1, 1969

By L. Hartsell Cash

INTRODUCTION Created in 1944 to help rebuild those economies, principally in Europe, which were seriously damaged or destroyed during the Second World War, the World Bank--or to use its correct name, the International Bank for Reconstruction and Development-began its operational phase by making a loan to the Government of France to accomplish two tasks: (i) to import coal for space heating purposes; and (ii) to buy new machinery and equipment to help rehabilitate its coal mines. Once the thrust of reconstruction in postwar Europe was largely accomplished, the World Bank Group (for today the World Bank has three separate lending windows) turned to mobilizing funds to improve living standards in developing countries, which remains its primary goal today. Over this period of time, the World Bank Group has continued to assist the world mining industry in various ways and, since 1955 the World Bank Group has financed mining or mineral processing projects with loans/credits totalling $1.5 billion. The World Bank Group consists of two institutions--the World Bank itself and the International Finance Corporation (IFC), which was founded as a separate institution in 1956 and three separate lending windows--the World Bank, the International Development Association (IDA), and IFC. The World Bank loans are provided at commercially-related interest rates but have grace periods usually of up to 3 to 5 years and repayment periods ranging from around 15 to 20 years. Since the World Bank raises its operating funds on the international capital markets in varying currencies and in varying interest rates, it relends a basket of currencies at floating interest rates which are fixed every six months to reflect the Bank's own borrowing cost. At the present time, the interest rate is just below 10% per year and in addition, a one-time front-end fee of 1/4 of 1% is charged. Also, a commitment fee of 3/4% per year is charged on the undisbursed amount of the loan itself. For loans to industrial and mining projects, it is normal to charge an additional guarantee fee of 1 to 1.5% in addition to the annual interest rate. This guarantee fee is payable to the government of the country in which the project is carried out since, by its charter, the World Bank is required to have the guarantee of the host government for each loan made in a specific country. By far the greatest source of lending funds within the World Bank Group is that of the World Bank itself and for the fiscal year ending June 30, 1984, the World Bank approved loans totalling $12 billion. The second lending window within the World Bank Group is IDA which performs the same functions as the Bank itself and has the same staff. Nevertheless, its loans (called credits) are made on much softer terms and are made to the poorest nations only. IDA funds are subscribed by the wealthier countries, usually as grants, and these are relent as credits to those countries with the lowest per capita income. IDA credits are made for 50 year periods, including 10 years of grace, to the government itself. The credits are interest free, but there is a service charge of 3/4% per year on the amount withdrawn and outstanding to defray the administrative costs of IDA. Credits approved during fiscal 1984 totalled $3.5 billion. The third lending window is IFC. While IFC is a separate corporation and operates quite separately from the World Bank and has its own staff and regulations, it works very closely with the World Bank on its overall approach to the mining sector and to a particular country. IFC's mission is essentially to supply venture capital and to stimulate development of the local private sector in capital markets as well as to promote the international flow of private capital to developing countries. Unlike the World Bank and IDA, the IFC does not lend directly to governments

Jan 1, 1985

By F. W. Glaser, Benjamin Post

A LTHOUGH most transition metals form a wide variety of boride compounds, the existence of only one zirconium boride, ZrB2, had been established prior to this investigation.' The crystal structure and some properties of a hitherto unreported zirconium boride, ZrB12, are described in this paper. Only one other dodecaboride of a transition metal, UB12, has been reported up to the present.' Chemical analysis of the new compound showed 44 pct Zr and 56 pct B, compared with 41 pct Zr and 59 pct B computed for ZrB12. The difference is within the range of error of the analytical method employed. ZrB12 shows marked metallic properties. It is obtained as a fine black powder. Measurements of electrical resistivity were made at —79°C, + 22°C and +64°C. At 22°C the electrical resistivity is approximately 60 microhm-cm. Over this range the temperature coefficient of resistivity is +0.00162. The thermal conductivity at room temperature is 0.122 watts per cm per "C. The product of the electrical resistivity and thermal conductivity is therefore 8.05, which is not far from the normal Wiedemann-Franz ratio (approximately 7.5 at room temperature). These measurements were made on hot pressed samples which were not always high density specimens. The hardness of ZrB12 on the Rockwell A scale varies between 92 and 92.5. Crystal Structure Determination Single crystals of ZrB12 of a size suitable for X-ray diffraction analysis could not be obtained and powder samples had to be used. Filtered Cu radiation was used throughout. Powder diagrams were indexed on the basis of a face-centered cubic unit cell. After correction for film shrinkage, a Bradley and Jay extrapolation³ to ? = 90" indicated that a, = 7.408 ±0.002A. The volume of the unit cell is 406.5A.V he assumption that there are four "molecules" of ZrB12 per unit cell leads to an X-ray density of 3.63 g per cc. The measured density is 3.7 g per cc (as measured by the immersion method). Relative intensities of reflections were determined by integrating the intensities of diffraction peaks using the count register of a North American Philips wide range spectrometer. Intensities measured in this way showed good agreement with photographic intensities estimated visually using multiple film techniques. The usual Lorentz, polarization, and multiplicity corrections were applied to the observed intensity measurements. There are striking similarities between ZrB12, and UB12. The unit cell of the latter is also face-centered cubic and contains four molecules. a, = 7.473, compared with 7.408 for ZrB12. The radius ratio rB/rU is 0.57; rB/rZr is 0.54. In both ZrB12, and UB12 the four metal atoms in each unit cell are in special positions; only the boron positions need be determined. The latter may be inferred from the extent to which diffraction of X-rays by the 48 boron atoms reinforces or weakens the diffraction by the metal atoms. This effect is relatively much greater in the case of the zirconium compound. In their determination of the crystal structure of UB12, Berthaut and Blum' assumed holohedral symmetry (space group Oh5 , Fm3m) and reported that the U atoms are in positions 4(a): 000; 01/2 1/2; ½ 0 ½ ; ½ ½; the boron atoms were reported to be in positions 48(i) with x = 1/6: ½xx; ½xx; x½x; x½x; xx½; xx½; ½xx; ½xx; x½x; x½x; xx½; xx½

Jan 1, 1953

By D. L. Everhart

The search for new deposits raises two important questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? A review of the wide geological variety of recent uranium discoveries tells how these questions are being answered. SOONER or later intelligent exploration for uranium leads to these questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? These matters, of course, make a big difference in how best to look for orebodies. Before these questions are discussed it might be well to point out other factors bearing on the subject. The whole business of uranium exploration is only a little over ten years old, participation by the public is only about six years old, and real interest and activity by more than a few large mining companies has arisen only in the past two or three years. Throughout this short period, uranium exploration has been affected by the unique influences of necessary security measures and by division of the overall job into individual projects by a large number of specialists in diverse fields. This has meant that a normal interchange of information on the nature of uranium deposits has really only just begun. Compared to the vast amount of published studies on iron, copper, lead, zinc, and gold deposits over the past 50 to 75 years, current knowledge of uranium deposits is in its infancy and much of the pertinent information is still scattered about in a number of unpublished sources. The volume of reports on all phases of uranium exploration is now beginning to mount at a remarkable rate, and geologists with widely varying specialized backgrounds in uranium geology are engaging in spirited debates over the origin of uranium and the relative importance of geologic controls of various deposits. One of the most interesting features of known uranium deposits of the world is the wide variation, see Table I, in character and geologic environment. It should be noted that many types became prominent during 1953. The davidite-bearing veins of Radium Hill, South Australia, are almost unique, although the same mineral occurs in a different kind of deposit in Mozambique. Recent studies indicate that brannerite disseminated in the granite near Cracker's Well, South Australia, may soon constitute uranium ore. Basalt has been added to the list of favorable host rocks in the Northern Territory of Australia. Basalt is also the host of the pitchblende veins of the Martin Lake deposit, Beaverlodge district, Saskatchewan. The truly remarkable rich and extensive Steen deposit near Moab, Utah, is of the uraninite-vanadium oxide type. Secondary hydrous uranium arsenates and phosphates constitute the uranium minerals in the disseminated deposits of the Wind River Basin, Wyo., a new district discovered in the summer of 1953. Uranium minerals in shales adjacent to fractures were newly reported in New Mexico and several other parts of the world during the year. The well-known important uraninite dissemination in the Rand conglomerates of South Africa has a counterpart, as discovered in the summer of 1953, in the Mississagi quartzite and conglomerate of the Blind River district, Ontario. Gunnar deposit of the Lake Athabaska district, Saskatchewan, consists of uraninite in both granite and sedimentary gneiss beneath a granite cap, and large new orebody of the Eldorado Co. in the same general area follows a preferred stratigraphic horizon in schists. Uranium is, generally speaking, a very soluble and ubiquitous element. It occurs in at least two valency states and for this reason is not easily tied down in natural solutions. As Gruner' has pointed out, it is probable that uranium starts in the hexava-lent state in nearly all solutions instrumental in its transfer. It is believed that under oxidizing conditions the uranium moves in solution as the uranyl ion, UO. In solutions ranging in pH from 1 to 5, the uranyl ion is most commonly in association with

Jan 1, 1955

By Walter S. McKee

Discussion of the paper of WALTER S. McKEE, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2399 to 2411. J. W. RICHARDS, So. Bethlehem, Pa.-I regret that the author has overlooked the great usefulness of the electric furnace for the melting of ferromanganese in the manufacture of manganese steel. WALTER S. MCKEE, Chicago, Ill. (communication to the Secretary*)-In an article as brief as mine it was not possible to .fully cover the metallurgical field; this accounts for my not mentioning the electric furnace for the melting of ferromanganese in the manufacture of manganese steel, although the advantages of such an apparatus are fully appreciated by me. FREDERICK LAIST, + Anaconda, Mont. (communication to the Sec-retary?).-Manganese steel has proved very serviceable in our plant.. We are using manganese steel for the jaw plates on the 5-' by 15-in. crushers in the concentrator instead of cast-iron jaw plates which we formerly used. The manganese steel wears five times as long as the cast iron. We are also using manganese steel in our 8- by 20-in. crushers. In our primary crushers, which are 12 by 24 in., we still use cast iron because the manganese-steel plates wore unevenly and left shoulders which caused trouble in setting up the crusher. Another reason for preferring cast iron in these crushers is that they grip the ore better on account of wearing of the rougher surface. The surface of the manganese steel becomes polished and large pieces of ore fail to be drawn in. We recently tested 8- by 16-in. manganese-steel elevator buckets working on 2-in. undersize against malleable-iron buckets and found that manganese-steel buckets lasted two and one-half times as long as the malleable-iron buckets. We use manganese-steel screen plates on our 2-in. trommels and have found that they last about five times as long as cast iron. We also used manganese-steel wheels and rails under the 20-deck round table in our slimes-treatment plant. We first used cast-iron rails and wheels and found that these wore badly at the end of two or three weeks, while the life of the manganese steel seemed to be almost indefinite; we never had occasion to change any of the manganese steel rail sections or wheels in the year and nine months that the plant was in operation.

Jan 5, 1916

By Benjamin Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of :different types of hammer drills to various mining, quarrying, and, excavating operations, that an indication of the economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not I been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the"' rock drills;" that the placing of small holes inclined upward, at angles steeper than 40° above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In' spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped, three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized.

Jan 2, 1915

By C. A. Heberlein

The present war in Europe seems to have stimulated the demand for quicksilver. In July last, the price ranged around $35 per flask of 75 Ib., while to-day it seems to fluctuate between $47.50 and $50. The use of quicksilver in the form of fulminate, containing 70 per cent., and as corrosive sublimate, containing 73.8 per cent., must be extensive and a further market advance may be expected. With such an advance, some revival in quicksilver mining may be looked for, particularly in California, where many abandoned properties exist. What can be done with low-grade quicksilver ores under favorable conditions, particularly with low mining cost, may be seen from the following description of the Oceanic mine, near San Luis Obispo, Cal. Its operations date back to 1876, when rich sand ores were discovered. In three years 7,400 flasks of quicksilver were produced, but since then the deposit has been worked only sporadically . Until two years ago various attempts had been made by the Oceanic Quicksilver Co. to mine the more refractory "mud rock," which was encountered lying beyond the " sand rock." Mud and sand rock in varying quantities were treated together, with poor results, but operations were successful with sand rock of fair percentage. About two years ago, when all the sand rock had been exhausted, Murray Innes purchased the Oceanic mine. He found large quantities of low-grade mud rock, varying from 6 to 8 Ib. of quicksilver per ton, which at the prevailing low price of quicksilver demanded very cheap mining costs, in conjunction with high but cheap metallurgical extraction. At that time the extraction of quicksilver from mud rock ranged between 40 and 50 per cent., as far as I am able to learn. Mining The low cost of mining was the principal consideration, since, with mercury at 50c. per pound, the total gross value of the ore did not exceed

Jan 1, 1915

By H. S. Price, J. E. Warren

Techniques for studying the performance characteristics of heterogeneous reservoirs have been developed. The effect of permeability variation on both the steady-state and the transient flow of a single fluid has been investigated. Limited comparisons with field and laboratory data have been made. The physical models studied consist of random three-dimensional arrays of homogeneous porous blocks. The permeabilities of the individual elements are assigned according to a specific distribution function; uniform anisotropy is introduced by varying the relative dimensions of the blocks. A particular model is perturbed simply by re-arranging its elements at random. The behavior of a physical model is determined by digitally solving its numerical analogue. Based on computational experiments, subject to the restrictions implied by the assumptions that were made, the following general conclusions have been drawn. 1. The most probable behavior of a heterogeneous system approaches that of a homogeneous system with a permeability equal to the geometric mean of the individual permeabilities. 2. The effects of flow geometry and anisotropy on the most probable value of the effective permeability of a heterogeneous medium are finite but not significant. 3. The permeability determined from a pressure build-up curve lor a heterogeneous reservoir gives a reasonable value for the effective permeability of the drainage area. 4. A qualitative measure of the degree of heterogeneity and its spatial configuration are obtained from a comparative study of core analysis and pressure build-up data. It has been indicated that these conclusions are predicated on the assumption that the core analysis and the pressure build-up data represent true reservoir characteristics. Common sources of error in these data have been discussed. One of the most significant problems of reservoir engineering is that of determining the nature and the disposition of the heterogeneities that inevitably occur in petroliferous formations. It is with this problem that this paper is concerned. Extensive research, both theoretical and experimental, has provided reasonable descriptions of the physical processes that are associated with primary and secondaryrecovery mechanisms. Similar progress in the fie1d of numerical analysis and the evolution of truly high-speed digital computers have made it feasible to calculate the behavior of these mechanisms under almost any environmental conditions. It appears to be logical, then, to conclude that the mechanistic performance of any reservoir can be predicted with some confidence. Unfortunate1y, a necessary condition for the validity of this conclusion is that the formation be adequately described in a macroscopic sense. This condition cannot be satisfied ill general; therefore, a frustrating situation currently exists — it is possible to compute the effect of reservoir heterogeneity on behavior, but it is not possible to specify the heterogeneity itself. In many cases, the predicted behavior of a project is so completely dominated by irregularities in the formation's physical properties that the gratuitous assumptior, of a particular form for the variation can reduce the solution of the problem to a mere tautological exercise. While all porous media are microscopically heterogeneous, only macroscopic fluctuations need be considered since the fundamental concepts of reservoir mechanics are based on macroscopic quantities. For the simplest case in which only one physical property varies from point to point, the degree of heterogeneity that is apparent depends on three distinct factors, i.e., the nature of the property's variation (frequency distribution), its disposition (spatial distribution) and the inherent stability of the mechanism being studied. Consequently, any attempt to devise an unambiguous scale of heterogeneity must take these factors into account. Since this investigation is intended to be exploratory, it will be restricted to single-phase flow because of the simplification implied; both steady-state and unsteady-state behavior will be considered. Furthermore, to keep the number of parameters

By A. B. T. Werner, J. J. Schanz

A survey of the world's sources and markets for natural graphite and some predictions of future trends are presented here. The authors feel that there is no indication of major changes in sources of graphite over the next few years, but it is possible that the importance of domestic graphites as opposed to foreign carbons may increase in the more distant future. U.S. consumption of natural graphite, which has been in general decline for the past six years, and will probably continue downhill with the virtual disappearance of some markets. However, other markets such as bearings, brake linings and crucibles will probably grow. Natural graphite is the name given to all the naturally occurring mineral forms of carbon that crystallize in the hexagonal system. Natural graphite~ are generally divided into three broad classifications that are based on physical rather than chemical differences — crystalline flake, Ceylon amorphous and other amorphous. Crystalline flake graphites occur as thousands of small individual flakes disseminated throughout the ore and closely resemble shiny black fish scales. Ceylon amorphous graphite is mined from narrow veins of almost pure mineral. It is produced in lump form and often has a coarse platy or needlelike structure. Other amorphous graphites include all those that are extremely fine-grained and have a crystalline structure that is not visible under normal circumstances. In the primary raw material markets, the graphite's country of origin is also important. Crystalline flake graphites may, for example, be of the Alabaman, Bavarian or Madagascan types; Ceylon amorphous graphite may have originated in Montana or Ceylon; and other amorphous graphites may come from Mexico, Hong Kong or Korea. The distinctions between the graphites from each particular locality are small yet important, for the country of origin will signify certain inherent physical characteristics and will often give an idea of the amount of graphitic carbon contained in the shipment in question. .In certain instances, however, even this is not enough, since the actual mine at which the graphite is produced may have to be known before its true commercial value can be ascertained. Thus, the Madagascar flake graphite shipped from the Sahalambo mines of the Societe des Graphites de la Sahanavo is a thick flake which is known to be especially suited for use in crucibles, while the dull black earthy amorphous material formerly mined at Cranston, R.I., was ideal for stove polish. Synthetic, artificial, electric furnace and manufactured are terms used to describe graphites made from coke. These graphites will be considered in this paper only to the extent that they enter competition with natural graphite. DOMESTIC SOURCES OF NATURAL GRAPHITES Natural graphites have been produced from mines in Alabama, Alaska, California, Georgia, Montana, New Jersey, New York, North Carolina, Pennsylvania, Rhode Island, Texas and other states. The exception is the crystalline minerals resembling Ceylon graphite that have come from Montana and the amorphous meta-anthracites from Rhode Island. All the products mined have been flake graphite. In 1960, production was reported only in Texas and Pennsylvania. The Alabama graphite deposits of flake in quartz-mica schists are found southeast of Birmingham in a narrow belt that extends for about 60 miles southwest from Delta in Randolph County to Verbena in Chilton County. Since the long-run prospects for Alabama graphites appear to be fairly bright, especially if regular production of high quality output becomes possible, regional ore reserves of all kinds, including indicated and inferred, are estimated to be of the order of 25 million tons. Of this amount, 14 million tons are of the weathered variety. Alabama graphites are favored by their relative ease of mining, and by the fact that special methods of milling have been developed at the larger properties. In addition, the steady rise in ocean freight rates for Madagascar graphites, the tendency among crucible manufacturers to use flakes of a smaller size, and the possibility of producing other salable byproducts in addition to the graphite are favorable to Alabama producers. Against

Jan 1, 1962

By R. Lagneborg, R. Gullberg

An X-ray method for determinig volume fractions of phases in textured materials has been developed. The method involves measurements of the integrated intensities of reflections of each phase for one single orientation of the sample. The method was checked by evaluating the phase contents in samples from two stainless Cr-Ni steels containing austenite and ferrite in known amounts. In the present case measurements of about five reflections from each phase were required. The agreement between calculated and known volume fractions was found to be very close. AN X-ray diffraction method is often employed for determining the amounts of two or more phases in a material. The details of the method have been described at several instances.'" In short, the method is based upon the fact that the integrated intensity of a reflection is directly proportional to the volume fraction of the phase considered. In principle, the method only requires the measurement of the intensity of one reflection for each phase. The most severe shortcoming with this method is that it disregards influences from preferred orientation in the material. In a diffractometer, where this type of analysis is most conveniently carried out, the geometry is such that the diffracting planes for a specific Bragg peak are all parallel to the surface of the specimen. This implies that it must be required that the occurrence of the diffracting planes parallel to the specimen surface must be as frequent as for any arbitrarily oriented physical plane of the sample. This requirement will generally only be fulfilled for a material free of texture. Since all materials in reality always exhibit a preferred orientation to some extent. the deficiency of the method is quite serious. In cold-deformed material the texture is appreciable, but also annealed material will in many cases display a considerable texture. The problem of quantitative phase analysis in textured material is one of obtaining the integrated intensity averaged over all orientations of the specimen with respect to the X-ray beam. Lopata and ~ula~ have shown that this can be accomplished by integration of intensities over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. Hence, in this method the average integrated intensity for a specific reflection is obtained by directly determining the intensity for a sufficient number of physical orientations of the sample. However, since an excess of diffracting planes in a certain surface plane necessarily must be accompanied by a deficiency of another type of diffracting plane, it appears to be possible to obtain the correct average intensity for a specific diffracting plane by performing an appropriate averaging of intensities belonging to a large number of diffraction planes of different hkl when all intensities have been produced from one single orientation of the specimen surface. In the present work such a method has been attempted and tested experimentally for two stainless Cr-Ni steels containing austenite and ferrite. 1) THEORY The expression for the integrated intensity of a Bragg reflection diffracted from a phase in a polycrys-talline sample in a diffractometer is: where C is a constant only dependent on the incident X-ray power and the diffractometer geometry, v the volume of the unit cell, F the structure factor, m multiplicity of the diffracting plane, L Lorentz factor, P polarization factor, e-2 temperature factor, p average linear absorption coefficient of the irradiated vO1umej and V volume fraction of the phase 'Onsidered. Hence, the factor R in the abbreviated form of Eq. [I] can be calculated and depends only on 0 and the diffracting plane {hkl}. For an alloy containing two phases, a and y, we can write

Jan 1, 1967

By T. R. Graham, R. S. Dean. J. R. Long

Although considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to II pet aluminum, with some incidental information on the single-phase alpha solid solution alloys. Straussl gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper6 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50" temperature levels from 400' to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solub%ty of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 13oo'F and higher,

Jan 1, 1947

By R. S. Dean. J. R. Long, T. R. Graham

Although considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to II pet aluminum, with some incidental information on the single-phase alpha solid solution alloys. Straussl gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper6 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50" temperature levels from 400' to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solub%ty of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 13oo'F and higher,

Jan 1, 1947

EDWARD W. PARKER,* Philadelphia, Pa. (written discussion ?).-The two papers on coal-mine costs and pride fixing that Mr. Norris has contributed to the Transactions possess as much general interest and are of as much value to the coal-mining industry as any papers that have been presented in recent years. Until recently one of the troubles with the coal business, and especially the bituminous branch of it, has been that because of the lack of a uniform system of cost accounting (many operators, I regret to say, not having had any system at all), the industry as a whole may be said not to have known where it was at. The system adopted by the Federal Trade Commission may not be absolutely perfect but it has accomplished something in that it has compelled a uniform method of reporting and tabulating costs giving results of these compilations which are comparable. The Institute and the coal-mining industry owe a vote of thanks to, and of confidence in, Mr. Norris and his two associates on the Engineers Committee of the Fuel Administration, Messrs. Garnsey and Allport, for the great work they have done in interpreting the results compiled by the Federal Trade Commission, not to speak of the personal sacrifices made by them in giving their services to the government. Those who have read Mr. Norris' paper will probably join me in wishing he had brought out a little more fully the real meaning of the charts so far as they indicate the difference between the cost of producing a ton of anthracite and the price the operators receive for their product. Mr. Norris could have done this more satisfactorily than anyone else. It seems to me that particular attention should be drawn to the fact that, according to these charts, and the tables accompanying them, not less than 25 per cent. of the total output of anthracite, whether "company" or "individual," during the period covered by Mr. Norris' paper,

Jan 4, 1919

By D. J. Freeh, W. E. Horst, R. C. Kellner

This paper is concerned with the description of grinding characteristics in a batch grinding system. A mathematical model was developed and used for simulating the system on an analog computer. A general equation describing the change of selected size fractions with respect to time is presented. The empirical verification of the model is discussed. In order to understand the performance of a grinding system, it would be desirable to have a mathematical description of the system's behavior. The development of a mathematical model to describe the performance of a batch dry-grinding operation was investigated. This is the first step toward reaching the objective of a practical mathematical description of a grinding system that could be employed for process control and optimization of a simple or complex grinding circuit. Although this article is concerned only with batch grinding performance, experimental work is being conducted to extend the model to continuous grinding systems. BASIC PROCESS CONSIDERATIONS In a paper dealing with the probability theory of wet ball milling, Roberts1 correlated the rate of change of oversize material, C, with energy input, E, as follows where the energy input is expressed in power/unit mass and k is a constant for each particle size. Experimental grinding studies were made by Bowdish2 to extend the previous work of Roberts. The work of Bowdish also showed that the rate of breaking of oversize particles in a ball mill is proportional to the concentration of oversize particles present. He further demonstrated that breaking of oversize particles is proportional to the surface area of the balls used for grinding. Rate equations were presented and it was concluded that grinding could be considered as a first order phenomenon according to the rate equation [2] di which is in accordance with Eq. 1. In Eq. 2, the effect of ball area is included in the constant k,. Other rate equations were reported to show the effect of a change in ball area and removal of fines during grinding. Correlation studies made by Arbiter and BhranY indicate a first-order rate equation for quartz; however, their data showed less than first-order rates existed for some of the other materials evaluated. More recently Kelsall4 has shown that the rate of breakage of any narrow size range of quartz could be described by a first-order rate equation. Several other investigators5-7 have described grinding behavior in terms of rate equations or kinetics. In general, the rate equations have been described for each particle size; however, the interactions between sizes and the overall relationships that exist have not been considered, at least not in the form of solving a group of simultaneous differential equations. Extensive work has been conducted by various investigators using a probabilistic approach which has expanded stein's' earlier work. Selection and breakage matrices are incorporated in the probabilistic model as contrasted with the deterministic method presented here. A batch grinding operation may be considered as an unsteady-state process from the standpoint that the conditions within the mill are a function of time. Therefore, a plot of mass fraction of the i-th size versus time would give a set of curves as shown in Fig. 1. In these curves X , represents the mass fraction of large size material, X2 intermediate size, and X3 small size material. An examination of these curves shows a strong similarity to the curves that would be obtained from a chemical reaction of the type9 A?B?C, [3] where A would be comparable to the largest size material being broken to an intermediate size, 3, and

Jan 1, 1968

By F. Kurata, P. C. Davis, T. L. Gore

An experimental method and apparatus for the study of the low-temperature phase and volumetric behavior of volatile mixtures are described. The phase diagrams, including the critical points, and the volumetric behavior of a natural gas and a mixture of the natural gas with methane at temperatures from -40°F to -200°F and pressures to 1.200 11si are givrn. INTRODUCTION Knowledge of the phase and volumetric behavior of mixtures of the light hydrocarbons at low temperatures is becoming increasingly important as interest in low-temperature separation processes increases. Distillation at low-lemperatures has been used for some time to recover ethane and ethylene from natural gas and refinery gas for petrochemical uses. Removal of excess nitrogen from natural gas by distillation has been proposed as a means of increasing the capacity of gas transmission lines and of improving the marketability of the gas.1,2 Evaluation of the latter process has been hampered, however, by the scarcity of data from which the phase behavior of natural gases at low temperatures might be predicted. While existing correlations of vaporization equilibrium constants may be used to predict the behavior of such mixtures at lower pressures, high-pressure computations often require knowledge of the location of the critical point of the system involved. Although correlations have been developed for the prediction of the critical temperature and pressure of certain types of hydrocar-bon systems, they do not apply to very volatile systems such as nitrogen-bear-ing natural gases. This paper describes the initial stages of an investigation of the low-temperature behavior of a numher of natural gases and other gases of commercial interest. The experimental method and apparatus are described. and the phase and volumetric behavior of a natural gas and a mixture of the natural gas with methane are presented. PREVIOUS WORK The published low-temperature vapor-liquid equilibrium data for hydrocarbons and mixtures of hydrocarbons with nitrogen and helium are listed in Table I. Most of these data are for binary systems, and the data of Stutz-man and Brown" at 100 psi are the only data on a natural gas. The data of Bloomer and Parent3 on the methafie-nitrogen system, which have been phblished since this study was completed, are a valuable addition to the knowledge in this field. Prior to the publication of these data the only published critical point data on systems having critical temperatures below the ice point were those of Ruhemann.1 on the methane-

Jan 1, 1952