Search Documents

By C. E. Sims

In some experimental work conducted several years ago, it was noted that sulphur seemed to have a distinct influence on grain size of carbon steels. 111 order to check this observation, a series of S..A.E. 1040 steels was made with the normal composition held as nearly constant as possible. The steels were made with three sulphur levels, which were 0.012, 0.024 and 0.038 per cent sulphur, respectively. For each of the sulphur levels, steels were made with only silicon deoxidization and with aluminum additions of 0.1015, 0.025, 0.050 and 0.10 per cent. The melting medium was an acid-lined high-frequency induction furnace. These steels were forged and rolled and differentiall!. quenched from temperaturcs in the range of 1500O to 1800°F. After this, the A.S.T.M. grain size was determined and plotted as in Fig. I. It will be noted, first of all, that the aluminum-free steels had filler grain size with higher sulphur when heated to 1500, but that this condition was reversed at 1700°. When aluminum was added to produce fine grain size, the steels in the lowest sulphur level were fine-grained only to 1600°. and then only with an addition of one pound of aluminum per ton. The medium sulphur steels werc fine-grained to 1600' with a wider range of aluminum addition. The steels in the highest sulphur level were fine-grained at 1600° over a still wider range of aluminum additions and fine- grained at 1700° with an addition of one pound per ton. Fig. 2 shows curves of the grain-coarsening temperature for these steels and illustrates how sulphur and aluminum combine to give greater inhibition to grain growth than aluminum alone. Only the highest sulphur steels have a grain-coarsening temperaturc above 1700°.. At 1650°, the low sulphur steel is fine-grained only at its peak, while the highest sulphur steel is fine-grained over a wide range. In these tests, one pound of aluminum per ton gave the best results; this is equivalent to about 1 1/2 lb. per ton for commercial condition. IllcQuaid-Ehn tests made on these steels showed the same trend but to a lesser degree. The tests were repeated on a series of S.A.E:. 1015 steels with sulphur levels of 0.02 and 0.03j per cent. Aluminum additions were made in the range from 0.025 to 0.15 per cent. These steels were forged and rolled, normalized at 2000°F. to put them all in the same starting condition, then reheated to various temperatures from 1600" to 1800" and cooled at rates that would allow ferrite precipitation in the austenitic grain boundaries. The results of these tests arc shown in Fig. 3. It will be noted that. up to the temperature of 1650°, there is very little difference in the grain size obtained from the two levels of sulphur. .At temperatures of 1700° and 1750°, however, the lower sulphur steel was fine-grained only with an aluminum addition of 1 1/2 lb, per ton;

Jan 1, 1945

By G. S. Cole, G. F. Bolling

ThE exact type of fluid flow which occurs in a solidifying ingot is important in determining subsequent grain structure. This has been shown in studies of natural Convection" and of forced stirring or other disturbances of the melt."16 We shall explicitly argue that a complement to the existing natural flow in an ingot should be more effective than other types of flow in promoting the columnar-to-equiaxed transition. The ultimate effects of fluid flow upon structure is one of the topics of solidification that we have investigated in the alloy system Pb-Sb, under conditions simulating casting. In Fig. 1, the essential features of a bidirectional growth apparatus are shown; horizontal freezing from water-cooled faces within a low-thermal-conductivity lavite boat is a reasonable simulation of an ingot section. Details such as the furnace and thermocouples are omitted in order to show the location of four permanent. magnets, each with a pole separation of 21 in. providing a central field of about 1000 Gauss. When coupled with a dc current imposed through appropriate connections made at the cooled faces, a flow of fluid is produced as shown schematically. This technique described by Pfann and ~orsi" is ideal for our purpose since the flow indicated is the same as that we observe to occur naturally in this system. Components of 99.999 pct purity were used for study and all due precautions were taken in alloy preparation to avoid contaminants. Sections of the specimens were taken to ensure results representative of the interior as well as the surface of specimens. All proportions of equiaxed and columnar regions were measured by tracing the etched grain structures onto graph paper and simply counting squares. Four alloys were examined at superheats of 40" * 5°C and 100" * 9°C. Preliminary tests had shown that no appreciable enhancement of structure was obtained with magnetic field alone, so that this condition is not reported; it should nevertheless be noted that other configurations of magnetic field will reduce convection and thus enhance columnar growth.'8 For the tests reported the magnetic field was applied to a specimen by bringing the four preassembled magnets to a position 2 mm from an outer tube immediately after the ingot was poured. The dc current of 30 amps passed through the sample throughout the entire solidification cycle, resulting in a power dissipation of 9 w per sq cm of interface. This may be compared to the evolution of latent heat of approximately 18 w per sq cm. Table I contains the results of this experiment in terms of the total area ratio, equiaxed/columnar grains, as a function of the field interactions, solute concentrations, and superheats employed. The total structure of the ingot is seen to be most influenced when both the field and current are applied simultaneously; when current acts separately, little effect may be noted in spite of the heat supplied. In addition, the change in structure from the no field-no current case to the field-current condition is more pronounced at the higher superheat, and the higher the concentration of antimony. An example of the grain refinement, as well as the increased equiaxed zone, is shown in Fig. 2. It is now important to prove that there is indeed an increase in fluid flow due to the presence of the field-current interaction; this is done by temperature measurements in the liquid metal. Let us consider a bidirectional casting in which heat is applied to and removed from the system, in such a way that rate of solidification is zero.* When a sensitive thermocouple

Jan 1, 1967

By E. H. Lee, F. J. Fayers

Problems in reservoir analysis can usually he cupressed in terms of a system of nonlinear partial difjerential equations. A rnethod for .setting physically reasonable boundary conditions for these systerrls by ayplication of the theory of characteristics is discussed. A short description i.c. given of the technique for finding chnmcteristics of general first order and second orrler equations. Specific examples are quoted jrorn eqrrations occurring in theoretical reservoir studies. The princip1e. ossocicred wit11 the use of chnracteristic to set physically realistic boundary conditions me developed, and thr method is discussed in terms of boundary condition for the noncupillary, compressible, two-phase flow problen: jor the cupillary, ir~cowlpressible, two-phase flow problems for the tlrtergent flooding prohlenl; as for the compressible. noncapillary, two-phase flow pro11letn. INTRODUCTION In most problcms in reservoir analysis the physical situation is described by a system of nonlinear partial differential equations. The general solution to the set of equations usually comprises a wide range of functions ancl a particular solution is normally selectetl by applying suitable boundary conditions to the problem. In some cases it is clear from the physical situation what form the boundary conditions should take, but it is usually desirable to have an independent mathematical check of the suitability of the chosen conditions. From the mathematical standpoint, a system of partial differential equations with boundary conditions is said to be properly set if the combination determines a unique solution which is continuously dependent on the equation and the boundary conditions. Such a solution is sometimes termed "reasonable". In investigating the properties of the mathematical representation, it is useful to determine the structure of the system by the application of the theory of characteristics. This theory determines in the space of the independent variables, lines or surfaces which play a special role in thc system's behavior. The characteristics determine the possibility and nature of the propagation of discontinuities in the derivatives of the dependent variables. Along the characteristics certain differential relations hold which for some problems allow a so- lution to be obtained analytically. In the case of hyperbolic equations the characteristics can bc used as 3 basis for a numerical solution. If a complicated nonlinear system is to be solved, a study of behavior of the characteristics will indicate what boundary conditions should be chosen. By using the method of characteristics, several advances have rccently been made in solving reservoir engineering problems. Sheldon, Zondek and Cardwell' have discussed how the the method may be used grap-phically to solve the incompressible two-phase displaccmerit problem when the gravity term is included in the equations. Fayers and Perrine' have applied the method to study the equations representing detergent flooding. When compressibility and solution-gas effects are introduced into the two-phase flow problem, the equations and their characteristics become more complicated. It will be seen that in this problem the characteristics are useful for indicating a reasonable set of boundary conditions but cannot readily be used to compute a numerical solution. This problem has been solved on the IBM 701 using normal finite difference methods hy West, Garvin and Sheldon." The material to be prcscntcd in this report is divided into three sections. The first discusses the determination of the characteristics of first and second order partial differential equations; the second describes the selection of suitable boundary conditions by the application of the principle that the future cannot affect the past; the third discusses the use of characteristics for setting the boundary conditions of the two-phase solution-gas flow problem. A useful introduction to the method of characteristics has been given by Hildebrand.' A summary of the method will be given in this section of the paper. The First Order Equation The quasi-linear equation of first order is It is linear in the partial derivations of z. The properly linear equation has the form The characteristics of are curves along which the

By H. H. Kaveler, W. R. Evans, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By W. R. Evans, H. H. Kaveler, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By D. J. Carney, E. Richard Randolph, E. Van Meter, J. J. Oravec, Stanley H. Ward, Gerald J. Anderson, Rolland L. 203-000-000-005 Blake

DURING the last 30 years the inductive electromagnetic method has been used chiefly in the search for massive sulphide mineralization. This application has met with varying degrees of success and in recent years has resulted in discovery of several large orebodies. Little has been written concerning its use in exploration for soft iron ores, but one of the present authors has reported on experiments with massive magnetic deposits.' To augment the exploration tools available to geologists in delineating iron orebodies, Cleveland-Cliffs Iron Co. and McPhar Geophysics Ltd. undertook in 1953 to apply the inductive electromagnetic method to Cleveland-Cliffs properties in the Lake Superior region. As a result of this project, equipment has been developed that enables simultaneous transmission of two audio frequency waves, and the field technique and interpretative procedure involved have furthered exploration in the district significantly. Thus far, inductive electromagnetic application in the Lake Superior region has been only a development tool, that is, it is used to locate obscured contacts and faults as a part of property expansion and development. However, its application to primary reconnaissance of unexplored areas may be feasible in the future. The method has assisted in placing drillholes efficiently, and the elimination of excess drilling foot-ages and/or actual elimination of unnecessary holes has amply justified the expense of the geophysical survey. Cost of the field work involved is comparable on a per station basis to the cost of a magnetometer or superdip survey. Since observations require no reduction, i.e., are directly interpretable, overall expenditure is low, and the scope and detail of the survey can be adjusted in the field as geological- geophysical correlation becomes evident. To a great extent, this eliminates the second-guessing so commonly arising after office calculations are completed on data obtained with other types of geophysical surveys. This unique feature of field interpretation and its associated intimate feel of the project area, is, perhaps, one of the most valuable aspects of the inductive electromagnetic method as applied to iron ore exploration. Basis of Method Fundamentally, the method involves transmission of an alternating electromagnetic wave, of a chosen audio frequency, which permeates the ground materials in the vicinity of a transmitting, or primary, coil, see Fig. 1. This wave, or field, induces an electric current in any conductor on which it is incident. The flow of an alternating current in a conductor sets up its own, or secondary, radiating electromagnetic field. These two fields form a resultant whose configuration depends on the following characteristics of the subsurface conductors: 1) size, 2) shape, 3) electrical conductivity, 4) magnetic permeability, and 5) frequency of the transmitted wave. To a lesser extent the resultant is also dependent on material adjacent to the conductor, topography, and surface conductivity. For illustrative purposes, the primary, secondary, and resultant fields may be represented by vectors. In operation, the direction of the resultant vector is measured by a small receiving coil tuned to the frequency of the transmitted wave. Generally speaking, the method can be compared to the transmission and reception of the familiar radio broadcast, with special variations permitting measurement of the effect on reception of intervening materials. Field Technique Mechanics of field operation are simple. The mast is set up in a vertical position and is then guyed in place. The transmitting loop then is raised by means of a sheave at the top of the mast and the coil connected to the motor-generator. A special plane table is clamped into position on the mast and the loop is plumbed. The plane table is oriented according to a grid system established over the project area. By means of this plane table it is possible

Jan 1, 1956

By U. N. Bhrany, N. Arbiter

F. C. Bond (Consulting Engineer, Processing Machin-Dept., AllisChalmers Manufacturing Co., Milwaukee) This is a very comprehensive paper. It deals with 1) size distribution functions, 2) energy-particle size relationships, and 3) criteria for grinding efficiency. The method of analysis used consists of tracing the increase and decrease of successive Tyler scale screen fractions as grinding progresses. The treatment is based upon the assumption that the work done in grinding is concentrated entirely upon the coarse size fractions in the mill. It is postulated that when a feed consisting entirely of particles of one size fraction is batch ground that finer fractions increase at a constant rate as grinding progresses, until finally each in turn begins to be ground and to decrease in amount. It is shown that under these conditions the empirical Gates-Gaudin-Schuhmann log-log size distribution plot can be logically explained. It is difficult to imagine any condition of ball mill operation, or any probability analysis, which would result in no grinding contacts on the finer particles present. However, the authors' postulate must be accepted if their conclusions are to be sustained. They conclude that the equation expressing the for mation rate of each size fraction can be resolved into the G.-G.-S. size distribution equation, and that the curvilinear portion of the log-logsize distribution line represents the only particle sizes which are being ground as well as produced. The author's statement that the G.-G.-S. Eq. 4 applies only to the finer portion of the size distribution while the Rosin-Rammler Eq. 6 applies over the whole size distribution range certainly supports the view that an exponential equation of the Rosin-Rammler type corresponds more closely to actual size distribution than does the power law G.-G.-S. equation. However, the G.-G.-S. equation is used to derive Eq. 8 and Eq. 9, which state that the energy required to grind a ton through a particular mesh varies inversely as the particle size to the exponent -a , whic h is the slope of the extended G.-G.-S straight line. This is stated to apply to both batch and continuous grinding. The G.-G.-S. slope exponent thus becomes very important in all crushing and grinding analyses by this method. The authors include some data which can be used to test their conclusions, as described below: We will consider grinding a feed composed of 14 mesh (1190u) to -200 mesh (74u). The average of 17 Allis-Chalmers grindability tests on quartz gives a work index (Wi) of 12.77. The -200 mesh product should have 80 pct passing 41.6u or P = 41.6. The equivalent 80 pct passing size of the 14 mesh feed particles is considered to be the particle diameter, as is true for spherical particles. Thus F is 1190u. In the work index equation 10 wi 10 wi 127.7 127.7 P f 41.6 1190 = 16.1 kw-hrperton. In Table I the ball mill exponent for quartz is 1.0 and from Eqs. 9 and 10: w=kw-hr/ton =Constan/(do/di) = 16.1 ton so that (1190) Constant/ Constant and the Constant equals 259. The tons per horsepower-hour value is 0.0464, in agreement with Table IV. The exponents for other minerals are listed in Tabl e 11. In Table IIA, the kilowatt hours per ton required to grind these minerals between the same sizes as the quartz, both by the authors' method and the work index equation, are listed. According to the authors kw-hrperton = 259/(16.1)".

Jan 1, 1961

By R. G. Charles, E. A. Gulbransen, S. Barnartt

KINETICS of the reaction of zirconium with pure oxygen at elevated temperatures have been studied by several workers for periods of time up to 6 hr.1-1 In two cases,3-4 . the experimental values of oxygen uptake, w, as a function of time, t, were best fitted to the parabolic rate law w2 = kPt + constant. In others,3,4 the cubic rate law w3 = kot + constant, showed better agreement. The most recent data of Gulbransen and Andrew4 indicate that the choice between the parabolic and cubic laws for empirical representation of the data will often be arbitrary. This is particularly true if the first few minutes of the reaction with a clean zirconium surface is attributed to a different oxidation mechanism, for deviations from either rate law were found primarily during the initial period. Thus, the kinetics of this reaction have been too uncertain to permit safe extrapolation to oxidation periods of practical interest (many hundreds of hours). The data to be described are of interest, for they indicate that the cubic rate law applies over long oxidation times. The reaction of zirconium with oxygen at 1 atm pressure was followed at 350" and 450°C for 500 and 200 hr, respectively. Abraded test specimens of pure zirconium sheet' 3.0 X 2.0 X 0.012 cm in size were oxidized by the procedure previously described,3 which included periodic cooling to room temperature for weighing. The surfaces were polished to a 4/0 finish using polishing paper wet with kerosene, then wiped with petroleum ether and washed in redistilled acetone. Fig. 1 shows plots of log ? vs log t. Each curve represents the average of duplicate measurements, and deviations from the average were generally less than 3 pet. The cubic rate law (slope = 1/3) is closely followed. The rate constants, 5.2, x 10 -6 and 2.4, X 10- (mg cm-2)3 per hr at 350" and 450 oC, respectively, are plotted as log k, vs 1/T in Fig. 2, together with cubic constants calculated from the data of Gulbransen and Andrew4 for abraded specimens from the same lot of zirconium. Their data refer to runs of 6-hr duration at a pressure of 0.1 atm 0 and under conditions of uninterrupted heating. In spite of these differences, the latter data yield a straight line which appears to apply equally well to the new extended time data. The energy of activation for the oxidation process, calculated from the slope of this line, i.s 38 keal per mole. This may be compared with the value of 47 keal per mole found by Belle and Mallett3 at higher temperatures. It may be concluded tentatively that extrapolation of short-term oxidation data for zirconium to obtain the long-term behavior is best done through the cubic equation ?3 = kpt + constant. References ' E. A. Gulbransen and K. F. Andrew: AIME Trans., 1949, vol. 185, p. A.515; JouRNal OF Metals, August 1949. 'D.p. Cubicciotti Journal Amer Chemical August1949.Soc., 1950, Vol. 72, P. 3 V. Belle and M. W. Mallett: Joulnal Electro chemical Soc., 1954, ' E. A. Gulbransen 339.and K. F. Andrew: Oxidation of Zirconium Between 400" Gulbransenand 800'C.and AIME Trarzs.. 1957, vol. 209, p. 394; JOUR-Nal of Metals, April 1957. IS Barnartt, B G. Charles, and E. A. Gulbransen: Oxidation of 50 weight pet uranium-zirconium alloy, Journul Electrochemical SOC., 1957, vol. 104, p. 218.

Jan 1, 1959

By C. A. Siebert, O. S. Duffendack, A. W. Herbenar

IN metallurgical problems involving the study of equilibrium in binary systems, the ,existence of an additional vapor phase, due to the presence of a volatile component in the alloy, has often been neglected. This is well indicated by the modified form of the phase rule, usually accepted in condensed systems in which pressure is not considered as a degree of freedom. In many cases the vapor pressure of the volatile component is exceedingly small and for all purposes can be considered negligible, in which case this form of the phase rule is applicable. However, alloys containing Hg, Cd, Zn, or Mg, tend to show very marked equilibrium vapor pressure, even in the solid state, and therefore present cases where the modified form of the phase rule no longer holds true. A quantitative determination of the vapor pressure of zinc in alpha brasses is not only of practical interest because of the loss of zinc in the processing of these alloys, but also of theoretical interest in that such measurements provide a means of applying the principles of theoretical physics and physical chemistry to problems of applied metallurgy. A number of investigators have reported vapor pressure measurements of zinc in alpha brasses. Hargreaves1 made extensive measurements which were used by Birchenall and Mehl² and Guttman³ for the determination of activity coefficients of zinc in alpha brasses. Hargreaves1 used a differentially heated quartz tube and measured the condensation temperature at one end corresponding to the temperature of the heated brass at the other end. Birchenall and Cheng outlined the condensation method of obtaining vapor pressure of zinc and Cd over some of their silver alloys." The primary object of the present investigation was to increase the range and accuracy of the vapor pressure data for the alpha brasses. Preparation of Alloys: Six alloys were prepared from Bunkerhill zinc and O.F.H.C. copper, both of 99.99 pct purity. The cast ingots were annealed for 24 hr at 550°C, scalped, cold rolled 40 pct and annealed for 50 hr at 550°C. The annealed bars were then surface ground and degasified for 30 min at approximately 550°C in an induction heated vacuum furnace. The surface of the bars was removed before milling the bars into relatively fine chips for chemical analysis and samples for the equilibrium cell. The analyses of the six alloys are given in table I. Experimental Method: The vapor pressure of zinc over the various alloys at a number of temperatures was determined from absorption spectra data. The spark source was produced by means of a high tension discharge between two electrodes of pure zinc. The design of the absorption vessel is shown in fig. 1. The vessel was constructed of transparent quartz which transmits the whole of the visible spectrum and the ultraviolet down to a wave length of 2000 A. The thickness of the vapor space was set at 0.8 mm so as to permit a relatively wide range of measurements without altering the vapor space, and thereby necessitating recalibration of the vessel. The furnace used for heating the absorption vessel consisted of a split wound furnace as shown in fig. 2. The spectrograph used in obtaining the transmitted zinc spectra was a double prism type especially designed for a region of 2500-3500 A. A step diaphragm used in conjunction with a tungsten filament provided the necessary intensity patterns required for calibration of the photographic plates.

Jan 1, 1951

By H. L. Gilbert, H. A. Johansen, R. G. Nelson

High purity electrolytic chromium plate has been hydrogen-reduced and arc-melted under inert atmosphere to give sound ingots. These ingots may be hot forged to break the as-cast structure and then worked at 500°C to finished form. An intermediate and final high temperature anneal gives best ductility and grain refinement. HE increasing interest in refractory metals for I use in high temperature gas turbines, jets, and rockets has led to great efforts in exploiting the fifth and sixth groups of transition elements. Much of the interest has centered upon production of metals that can be worked and fabricated by normal means to produce various engine parts or components having the high temperature characteristics of oxidation resistance and high creep strength required for such uses. If these pure elements do not exhibit all of the desired characteristics, it may be possible to obtain a high purity alloy that will. Since, in all cases, development of these transition elements has depended to a large extent upon removal of oxygen and nitrogen as a means for producing ductile metal, the hypothesis has been accepted that oxygen is the normal embrittling material in a high grade electrolytic chromium metal. Various methods have been employed in an effort to remove this oxygen by direct or indirect attack.' Many workers have endeavored to produce pure chromium through reduction of the oxide by carbon or active metals, while others have recommended fusion electrolysis of chromium salts or reduction of these salts by active metals, such as sodium or calcium. Hydrogen reduction of the oxide or chloride and thermal dissociation of the iodide have been reported to give high purity metal. Experimental Work The U. S. Bureau of Mines, Northwest Electro-development Laboratory, has systematically re-examined the more promising methods and developed two which produce metal having ductility at temperatures lower than heretofore described. It has been found' that oxide-free chromium chlorides in a NaCl-KCl carrier salt may be mag- nesium-reduced and the byproduct salts distilled off in vacuo to give a high purity chromium sponge. Fusion analysis conducted under the supervision of W. W. Horton of Knolls Atomic Power Laboratory showed the oxygen and nitrogen both to be below 10 parts per million on a selected sample. A small amount of carbon is carried over in the final metal from the chlorination and reduction steps which are carried out in graphite crucibles. This trace of carbon is not detrimental to hot ductility. A more practical method for producing ductile metal is through hydrogen reduction of high purity electrolytic chromium. Normal electrolytic chromium will, if "developed" for a few minutes at 1100°C in high vacuum, be found by the method of Adcock:; to contain about 1 pct chromium sesquioxide (Cr2O3). This small amount of oxygen may be effectively reduced by hydrogen.2, 4 The method employed was to crush electrolytic chromium plate in a gyratory crusher to pass 60-mesh; finer crushing appears to offer no advantage. A nitric acid leach removed the iron picked up during crushing. The leached powder was rinsed until neutral with distilled water and vacuum-dried.

Jan 1, 1954

By J. P. Heller

The purpose of this discussion is to comment briefly on one of the points raised in the paper. The topic is that referred to in the Conclusion 2, in which the authors note a "disproportionate increase in mixing rate" as they proceed from a displacement performed at viscosity ratio 0.998 to one at 1.002. The recovery curve of this displacement, Fig.2A, shows a quite noticeable difference between the two runs in which displaced and displacing liquids were interchanged. This difference is ascribed by the authors to the change in viscosity ratio between the two experiments. This interpretation of the experimental results must certainly be based on rather precise measurements of the fluid viscosities or, at least, of the ratio of their viscosities. The ordinary Ostwald viscometer, employed in the usual way, is only just able to distinguish between liquids whose viscosities differ by two or three parts per thousand. The experimental refinements which then must have been necessary to measure with any precision a viscosity ratio of 1.002 would be worthy of mention. Indeed, one would have expected the authors to devote at least a paragraph to the display of this technique. For the same reason - to emphasize that the details of such unusually critical experimental work should be reported and discussed in the literature — I would have liked to see some comment by the authors on the requirements for temperature control during both the viscosity measurements and the displacement experiments. The temperature coefficient of viscosity of Soltrol C at room temperature has been measured in this laboratory at about - 1.9%/1°C. How much did the coefficients for the fluid mixtures used in the experiment differ from this and from each other Even if the two fluids were identical in this respect, it would appear that a temperature difference of .l°C between them in the flow system would produce a viscosity con- trast equal to that imposed by their composition. Reference to the experimental solutions of these problems would render Conclusion 2 more credible. Published theoretical work on the stability problem contains no indication of such extreme sensitivity to the viscosity ratio in the immediate neighborhood of unity. On the contrary, perturbation calculations such as those made by Chuoke1 and Perrine2 lead to initial finger growth rates proportional to the first power of the viscosity difference. The later instability growth calculated by Scheidegger,3 using the assumption of zero pressure gradient perpendicular to the average flow, is also simply proportional to the viscosity difference. The conflict regarding the sensitivity of the dependence of instability growth or mixing rate on the viscosity contrast needs explicit recognition in the literature. In particular, it would seem that the experimental work reported here should be supported by a more detailed description of the viscosity controls. Further discussion of possible alternative interpretations of the data would also be in order. For instance, is it possible that the unconsolidstted bead pack used changed its characteristics between the runs (due, perhaps, to the handling and inverting involved in the injection of the front) Or, are the data points of Fig. 2A averages from several runs performed in a series in which the two liquids alternated as displaced and displacing fluids? To summarize, it seems to me that the relationship asserted by Conclusion 2 in the paper needs the support of more detailed experimental evidence. REFERENCES 1. Chouke, R. L., van Mews, P. and van der Poel, C.: "The Instability of Slow Immiscible Viscous Liquid-Liquid Displacements in Porous Media", Trans., AIME (1959) Vol. 216, 188.

By Thomas P. Bispham

INTRODUCTION From the lender's point of view, the greatest period of risk in a project financing occurs during the construction phase. Therefore, most projects are supported during this phase by completion guarantees supplied by some credit-worthy entity; for example, the project sponsors in the case of a joint venture, such as that of W.R. Grace, Hanna Mining, and Liberty Capital; or by a strong contract with a utility or foreign importer/investor, such as the way North American Coal Corporation has structured many of its transactions. THE PROJECT LOAN REQUEST A project financing is a more complex form of term loan than one using an ongoing corporation's balance sheet as a credit base and, therefore, a potential lender will subject the loan request to a more rigorous analysis. To support this effort, the financial institution will require a more detailed information memorandum to evaluate the credit and technical risks of a project - especially since much of the necessary information is not otherwise available. (See also Gibbs and Sroka paper above in this Chapter) A well-prepared information memorandum will impress prospective lenders with the planning ability and general competence of management. Also, the process of preparing the memorandum will help management understand the true extent of the opportunities and limitations of its venture. Appendix A outlines the topics which comprise a complete information memorandum for a loan request. Of some interest to those seeking to sell a currently-operating mining venture, a similar information memorandum should be prepared i.e., covering the same topics discussed here, for the investment banker to use with potential purchasers. For that purpose, though, one might not want to prepare quite as much detail as for a lender. Appendix B outlines the elements of a reserve evaluation and feasibility study, often called the "Bankable Document." Usually, these studies are prepared by independent engineering consultants for use by potential borrowers and sellers. (Potential purchasers will often contract for a similar study for their use in evaluating an acquisition.) ELEMENTS OF A LOAN INFORMATION MEMORANDUM 1. Outline: The information memorandum should begin with a one-page outline covering such topics as: a. The borrower's name, address, and phone number. b. Principal contact at the borrower. c. Amount of the proposed financing. d. Desired pricing and structure of the proposed financing. This should include a description of the amount and source of equity in the proposed financing. e. Use of the proceeds and timing. 2. Summary: The most important information contained in the memorandum should be summarized in two pages. Note - If the borrower is a recently-formed single-purpose company, then elements 3, 4, and 5 will apply to the guarantors of completion and to the project sponsors. 3. The Borrower: This section is a brief biography of the borrower including such topics as date and state of incorporation, founder(s), lines of business, etc. 4. Capitalization: The borrower's current debt and equity position, including leases and trade debt, with amounts, terms, names, and addresses enumerated. Equity owners, and percentage ownership, should be identified. 5. Historical Financial Statements: If available, a minimum of five year's worth of complete historical financial statements

Jan 1, 1985

By C. E. Violet, R. J. Borg, E. M. Howard

The miscibility gap in the Au-Ni system has been determined by Mossbauer spectroscopy, with used as a probe. The phase boundaries were determined from the compositional dependence of both the isomer shift and Curie temperature. X-ray diffraction measurements were also used to confirm the Mossbauer results. 1 HE purpose of this research is to demonstrate the application of Mbssbauer spectroscopy to the determination of phase boundaries and to redetermine the miscibility gap by an independent and novel technique. The techniques evolved in this study are readily applicable to other polyphase systems and are generally as quick and accurate as the more conventional methods, e.g., metallography, X-ray diffraction, thermal analysis, and so forth. To be sure, not all polyphase systems will lend themselves favorably to Mijssbauer investigations, but this is a problem met in the use of conventional methods as well. The Mbssbauer spectrum responds to a different set of physical parameters, and consequently provides an entirely independent method of analysis. It is especially useful if the system has either a ferromagnetic or an antiferromagnetic transition. The Au-Ni system was selected because alloys containing more than -60 at. pct Ni become magnetically ordered at low temperatures; also the miscibility gap is quite well established (see Ref. 7 for a compilation of pertinent references, also Fig. 11, and thus provides a reliable test of this novel procedure. As Fe is the most commonly used Mijssbauer isotope, there exists a wealth of information concerning its behavior in iron-containing alloys and compounds. However, as yet there have been relatively few experiments using it as a probe to investigate nonferrous systems. By choosing a nonferrous alloy system, we are able to demonstrate that its use is not restricted to systems containing iron as one of the major constituents. Wertheim and ~ernick' have used the same method to investigate Cu-Ni, and demonstrated that one can obtain a systematic variation in the isomer shift and magnetic hyperfine field. However, we believe this to be the first time these techniques have been used to establish phase boundaries. Two hyperfine interactions were measured and used to determine the phase boundaries, viz., the magnetic hyperfine splitting and the isomer shift which in this alloy system are both strong functions of composition. Calibration curves were established based upon single-phase solid solutions obtained by quenching from temperatures well above the maximum of the miscibility gap, see Fig. 1. Solid solutions containing 25, 50, 65, 75, 85, 92, and 96 pct Ni as well as pure nickel were used in the calibration procedure. Fig. 2 shows the Curie temperature, TC, and the isomer shift, v,, as determined from the Mbssbauer spectra, and variation in lattice parameter as determined by X-ray diffraction, as functions of composition. The compositions of the two-phase systems quenched from temperatures within the miscibility gap are obtained by comparing their respective values of TC and v0 with the calibration data. I) EXPERIMENTAL Mbssbauer sources were made by fusing the component metals in a tungsten arc melter, which has a water-cooled copper hearth. Both nickel and gold were 99.999 pct pure, and the melting was done in an atmosphere of purified argon. The alloys were rolled, diced,

Jan 1, 1969

By H. R. Stahi

THE ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classifiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9 1/2 -in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3 ½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 5 2 ¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1 3/4in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges are renovated occasionally, broken pieces being removed and the charge brought up

Jan 1, 1945

By D. B. Jugle, J. B. Darby

The equilibrium solubility limits of the transition elements Ti, V, Cr, Fe, and Co in liquid tin were determined in the temperature range from 827" to 1211°K. Since the equilibrium concentration of Ti, V, or Cr in liquid tin is moderately dilute in the temperature range investigated, the solubility data were employed to estimate the partial molar enthalpy and the partial molar excess entropy of solution for the three solutes in liquid tin. The reference state s for titanium or vanadium were selected relative to the solute in an intermetallic compound. The thermodynamic quantities for chromium were calculated relative to pure chromium. RECENT experiments1 have shown that the rate of solution of several transition elements in liquid aluminum can be qualitatively predicted from a knowledge of the temperature dependence of the solvent-rich liquidus. In order to extend the analysis to binary tin systems,' it was necessary to know the equilibrium solubility of several of the first-long-period transition elements in liquid tin. Since solubility data for the tin-rich portion of binary systems are meager, the present investigation was undertaken to determine the equilibrium solubility limit of Ti, V, Cr, Fe, and Co in liquid tin in the temperature range from 850" to 1200°K. EXPERIMENTAL PROCEDURE A useful technique3 to determine the equilibrium solubility of a solute in a liquid-metal solvent consists essentially of placing a pure solute in contact with a pure solvent and allowing sufficient time for equilibrium to be attained at the temperature of interest. Subsequently, the solvent is removed and the equilibrium solute concentration in the solvent is determined by an appropriate analytical procedure. The technique can be applied very successfully to relatively simple systems such as the copper-germanium system.3 However, in many binary systems of transition elements with tin, several intermediate phases are known to exist and precipitation of the phases from solution, in solubility experiments, can lead to an erroneously large solubility. The difficulty was avoided in the present work by equilibration of the most solvent-rich intermediate phase with the pure solvent over a range of temperatures. The compounds employed in this investigation, and the temperature range over which each compound is in equilibrium with liquid tin are listed in Table I. No stable intermediate phases are reported in the chromium-tin system4 and, therefore, pure chromium was utilized as the solute. The stoichiometric compounds were prepared by arc-melting on a water-cooled copper hearth in a helium-argon atmosphere. The elemental tin employed in.this investigation was 99.998 pct pure, and typical lot analyses of the transition elements were reported elsewhere.' A sample of an appropriate solute, in the form of a button and in sufficient quantity to exceed the equilibrium solubility, and the pure tin solvent were placed in a high-purity recrystallized-alumina crucible. The crucible and contents were placed in a horizontal furnace under a high vacuum (10-6 torr) and held at temperature for periods varying between 24 and 72 hr. A water-cooled quench tank, partially filled with diffusion-pump oil, was attached close to one end of the

Jan 1, 1970

By R. P. Alger, C. A. Doh, M. P. Tixier

The principle, the equipment and field operation of sonic logging are described. The tfio-receiver system produces logs independent of hole size and mud. Field experience is given and forms the basis for the interpretation of the log. The derivaiion of porosity values from measured velocities is discussed, according to the type of formations (hard formations, compacted sands, and unconsolidated formations). The time-average equation proposed by M. R. J. Wyllie, A. R. Gregory and L. W. Gardner is uscd as a basis for the computation of porosity in limestones, cemented sandstones and compacted sands. Variations in the lithologic character of limestones do not seem to change the porosity calibration markedly. The compaction of sands is related to the compaction of shale adjacent to them; and, thus, the shale velocity is used for the establishtnent of empirical relations for the computation of porosity in un-consolidated formations. Various forrnu.las are tentatively presented to account for shale and fluid content. Field experience demonstrates that considerable attenuation of sonic energy takes place in unconsolidated formations, particularly when gas bearing, and in fractrured formations. Unusually large attenuation produces skipped cycles, a feature easily recognized. The application of sonic logging to structura1 studies is featured, showing its possible integration with the dipmeter. Correlation and its application to the irrterpretation of seisrmic surveys are reviewed. The paper is illustrated with field examples. Sonic logging is the recording of the time required for a sound wave to traverse a definite length of formation. Sonic travel-times are inversely proportional to the speed of sound in the various formations. The speed of sound in subsurface formations depends upon the elastic properties of the rock matrix, the porosity of the formations and their fluid content and pressure. Below the "weathered" or low-velocity layer extending from 50 to 100 ft or so below the surface, sound velocities may range from about 6,000 ft/sec in shallow shales to as much as 34,000 ft/sec in dolomites. In hard formations (well cemented and/or compacted), the sonic log reflects the amount of fluid in the formations; hence, it correlates well with their porosity. In unconsolidated formations, which are usually of fairly high porosity, the sonic log gives an approach to porosity determination, when its readings are corrected for lack of compaction, shaliness, and fluid content. In such formations the sonic log may also indicate the presence of gas and may distinguish between oil- and water-bearing beds. Field experience with the sonic log in soft formations is more limited than that in hard formations. As a result, interpretation in soft formations is not as well developed at the present time. In all types of formations the sonic log is of considerable value for correlation and for the more detailed and accurate interpretation of seismic data. EQUIPMENT AND PRINCIPLE FIELD OPERATION The basic features of the sonic log" are a two-receiver system and two available short spacings. The log is recorded on film using a standard field unit. An SP curve is run along with the sonic curve to give a more interpretable log and to establish absclute depth control for comparison with other logs run in the same well. If desired, a gamma-ray curve may be recorded simultaneously with the sonic curve. Fig. 1 shows the sonic-gamma ray combination sonde. The sonic portion consists of a sound transmitter and three receivers mounted 3, 4 and 6 ft from the transmitter. When the first and second receivers are used, a sonic log of I -ft spacing (distance between receivers) is obtainea. Use of the first and third receivers provides a 3-ft spacing. The transmitter emits pulses at the rate of l0/sec. After the transmission of a pulse the first arrival of sound energy at each receiver triggers its response system. The differ-

By P. J. Root, J. E. Warren

An idealized model has been developed for the purpose of studying the characteristic behavior of a permeable medium which contains regions which contribute significantly to the pore volume of the system but contribute negligibly to the flow capacity; e.g., a naturally fractured or vugular reservoir. Unsteady-state flow in this model reservoir has been investigated analytically. The pressure build-up performance has been examined in some detail; and, a technique for analyzing the build-up data to evaluate the desired parameters has been suggested. The use of this approach in the interpretation of field data has been discussed. As a result of this study, the following general conclusions can be drawn: 1. Two parameters are sufficient to characterize the deviation of the behavior of a medium with "double porositym from that of a homogeneously porous medium. 2. These parameters can be evaluated by the proper analysis of pressure build-up data obtained from adequately designed tests. 3. Since the build-up curve associated with this type of porous system is similar to that obtained from a stratified reservoir, an unambiguous interpretation is not possible without additional information. 4. Differencing methods which utilize pressure data from the final stages of a build-up test should be used with extreme caution. INTRODUCTION In order to plan a sound exploitation program or a successful secondary-recovery project, sufficient reliable information concerning the nature of the reservoir-fluid system must be available. Since it is evident that an adequate description of the reservoir rock is necessary if this condition is to be fulfilled, the present investigation was undertaken for the purpose of improving the fluid-flow characterization, based on normally available data, of a particular porous medium. DISCUSSION OF THE PROBLEM For many years it was widely assumed that, for the purpose of making engineering studies, two param- eters were sufficient to describe the single-phase flow properties of a producing formation, i.e., the absolute permeability and the effective porosity. It later became evident that the concept of directional permeability was of more than academic interest; consequently, the degree of permeability anisotropy and the orientation of the principal axes of permeability were accepted as basic parameters governing reservoir performance. 1,2 More recently, 3-6 it was recognized that at least one additional parameter was required to depict the behavior of a porous system containing regions which contributed significantly to the pore volume but contributed negligibly to the flow capacity. Microscopically, these regions could be "dead-end" or "storage" pores or, macroscopi-cally, they could be discrete volumes of low-permeability matrix rock combined with natural fissures in a reservoir. It is obvious that some provision for the inclusion of all the indicated parameters, as well as their spatial variations, must be made if a truly useful, conceptual model of a reservoir is to be developed. A dichotomy of the internal voids of reservoir rocks has been suggested.7,8 These two classes of porosity can be described as follows: a. Primary porosity is intergranular and controlled by deposition and lithification. It is highly interconnected and usually can be correlated with permeability since it is largely dependent on the geometry, size distribution and spatial distribution of the grains. The void systems of sands, sandstones and oolitic limestones are typical of this type. b. Secondary porosity is foramenular and is controlled by fracturing, jointing and/or solution in circulating water although it may be modified by infilling as a result of precipitation. It is not highly interconnected and usually cannot be correlated with permeability. Solution channels or vugular voids developed during weathering or burial in sedimentary basins are indigenous to carbonate rocks such as limestones or dolomites. Joints or fissures which occur in massive, extensive formations composed of shale, siltstone, schist, limestone or dolomite are generally vertical, and they are ascribed to tensional failure during mechanical deformation (the permeability associated with this type of void system is often anisotropic). Shrinkage cracks are the result

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. Development of the new units was prompted by a desire for solution of the following problems: 1—The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pct of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be pro- vided in the event that air lines were no longer available. 2—Drill performance has increased beyond the capacity of present 3-in. drifter machines. 3—The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4—Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5—Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6—In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1—It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1953

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. Development of the new units was prompted by a desire for solution of the following problems: 1—The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pct of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be pro- vided in the event that air lines were no longer available. 2—Drill performance has increased beyond the capacity of present 3-in. drifter machines. 3—The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4—Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5—Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6—In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1—It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1953

By B. L. Averbach, M. Cohen, C. H. Shih

The isothermal formation of martensite is studied in Fe-Ni-Mn and Fe-Mn-C alloys under conditions where the athermal transformation is completely avoided, there being no martensite present at the beginning of the isothermal reaction. The initial rate of martensite formation is extremely low under these conditions, but it increases greatly as soon as some martensite is formed. It appears that true initial characteristics of the isothermal reaction can be studied only in samples wherein the formation of martensite on cooling is completely eliminated. THE phenomenon of isothermal martensite formation is well established1 -" but the observations have been made in the presence of varying quantities of athermal martensite. Complete avoidance of athermal martensite and the formation of martensite under pure isothermal conditions have been reported by Kurdjumov and Maksimova2 in an Fe-Ni-Mn alloy (23 pct Ni, 3.4 pct Mn, and the balance Fe) and have been confirmed by recent experiments of Cech and Hollomon in a similar alloy. In each case, the isothermal transformation rate was a maximum at the beginning of the transformation and decreased as the reaction proceeded. These initial transformation rates were used by Fisher7 for the confirmation of calculated nucleation rates based on classical nucleation theory extended to include the effect of elastic strain energy. Cech and Hollomon have admitted, however, that up to 3 pct martensite formed on cooling in their samples and thus was present at the initiation of their isothermal runs. In this paper, experiments on similar alloys are described, except that care was taken to remove the incidental martensite developed at the surface prior to the isothermal reaction. It is shown here that the reaction rate at the beginning of the strictly isothermal reaction is very low. As soon as some detectable amount of martensite is produced, the transformation rate increases rapidly but ultimately decreases as the reaction proceeds. When martensite is allowed to form isothermally in the presence of about 2 pct of prior martensite, the apparent initial reaction rate is a maximum and corresponds to the observations of Kurdjumov and Maksimova and Cech and Hollomon. It is evident that the cooperative nature of the martensitic reaction results in a significant stimulating or autocatalytic effect on the isothermal reaction rate. Experimental Procedure The chemical compositions of the alloys used in this investigation are listed in Table I. The Fe-Ni-Mn alloys A and B were melted in an induction furnace, cast into ingots 2 in. diam by 4 in. long, and forged into % in. diam rods. The manganese steel (alloy C) was melted in an arc furnace and cast into ceramic molds 1/4 in. diam by 5 in. long. The rods were sealed in evacuated Vycor tubes and homogenized at 1175" to 1200°C for 50 hr. The long homogenization resulted in some manganese loss from the surface, producing a thin layer of transformed material. This surface layer was removed by grinding and the specimens were then swaged to 0.050 in. diam wire. Measurements of electrical resistance were made with a Kelvin double bridge to follow the course of the martensitic transformation. A small permanent magnet was also useful in scanning an entire specimen for small localized quantities of martensite. This test is almost as sensitive as the electrical resistance method in detecting the presence of martensite (which is ferromagnetic in these alloys) and it was especially useful in deciding whether a specimen was completely free of martensite. The wire specimens (0.050 in. diam by 2.5 in. long) were sealed in evacuated tubes and austenitized for 5 min at 1150°C. The specimens were quenched into water and, unless otherwise stated, stress-relieved for 1 hr at 650 °C in order to induce greater uniformity in the subsequent martensitic transformation. As dem-

Jan 1, 1956