Search Documents

By J. N. Ong

The oxidation of tantalum is assumed to occur by four simultaneous first-order chain reactions; solution of oxygen in the metal, nucleation and growth of a suboxide phase at the metal surface and two phase boundary processes which give rise to two different modifications of Ta2O5. A rate equation is then formulated which accounts for all principal details of oxidation behavior, unifies and correlatss the results of the principal investigations, and expresses the rate as a function of pressure, temperature, and time. For purposes of practical application, the expressions: may be used below and above 700T respectively to determine the regression rate of tantalum in cm per hr, where T is to be expressed in "K and P in atmospheres pressure of oxygm. The equations will reproduce within a factor of two all reported experimental rates in the temperature range 475" to 1400°C and pressure range 0.000026 to 40.8 atm 0. 1 HE oxidation kinetics of tantalum have been investigated thoroughly in the temperature range 50" to 1400 and pressure range 1.32 x l0-' to 40.8 atm pressure of 0,and as a result, the principal features of the oxidation of tantalum are known and have been described in considerable detail. The exposition of the characteristics of the behavior of tantalum in oxygen has been largely descriptive, with considerable attention being devoted to elucidating the structure, composition, and morphology of the resulting oxide products. The weight change vs time results have usually been reported graphically. With the exception of the linear rate below 700 C and the process of diffusion of interstitial oxygen into the metal,6'9 no effort has been made to characterize the reaction rates in functional form. It is the purpose of this paper to demonstrate that when the fundamental principles of chemical kinetics are rigorously followed, the results of the principal investigations will be correlated and unified and the oxidation rale may be expressed as an analytic function of pressure, temperature, and time. In addition to accounting for the temperature and pressure dependency of the oxidation rate, the following minor features will be accounted for as a result of the basic analysis: the initial period of nonline-arity in rate at low temperatures, which decreases with increasing temperature;3'5'7 the rate vs temperature cusps obtained at constant pressure"5 the concentration gradient of oxygen interstitially dissolved in the metal.5'7 The analysis will also be consistent with the overall chemistry of reaction and with all visual, microscopic, and X-ray observations. DEVELOPMENT OF RATE EQUATION As a fundamental basis for the treatment of metal-oxygen reaction kinetics, it will be regarded that the rate of reaction is determined by the concentration and not the activity or chemical potential. It is further assumed that all metal-oxygen reactions are first order complex chain reactions" whose rate is dependent on the concentration of an intermediate species which is a complex function of the oxygen concentration, or oxygen pressure, only. The basic rate equation is therefore: is the weight of oxygen consumed by the reaction, A is that portion of the area of the metal over which the reaction is occurring (cm2), t the time (sec), kf the rate constant for forward reaction, C the intermediate species concentration and f '([Oz]) and f (Po,) are complex functions of oxygen concentration and Oxygen pressure respectively. Reverse reactions may usually be neglected in metal-oxygen systems since a large negative free energy generally accompanies these reactions. Eq. [I] takes different forms when the rate of reaction is controlled by diffusion into or through a phase or at a phase boundary. For diffusion into the metal phase, the rate is given by1' Di is the diffusion coefficient of species diffusing into the metal phase (cm2/sec), and Q is the corre-

Jan 1, 1962

By L. A. Wilson, N. H. Harrison, R. R. Clay, R. L. Reed. D. W. Reed

Experiments have been performed in a linear near-adiabatic system for the purpose of extending data on reverse and forward combustion from atmospheric pressure to 1,000 psig. Results obtained from reverse combustion appear to conform qualitatively with the existing description of the process when reaction kinetics are suitably modified to account for the increase in pressure, i.e., increasing tbe pressure decreases the peak temperature and increases the combustion zone velocity. Forward combustion appears to be a fuel dominated process wherein peak temperature and combustion zone velocity are not very sensitive to changes in pressure. The moderate effects of pressure that do exist at low flux virtually disappear at high flux providing all oxygen is consumed. With this provision. increasing the pressure decreases the frontal velocity and increases the peak temperature. Results me shown graphicaIIy which demonstrate the effects of presswe on peak temperature, rate of advance, oil recovery, air/oil ratio, carbon oxides produced and temperature distributions. INTRODUCTION Numerous field tests of oil recovery using the technique of underground combustion are now in progress. Operating pressures used are always substantially in excess of atmospheric pressure. Nevertheless, the literature contains no laboratory data pertaining to the effects of pressure except for those of Martin, Alexander and Dew.1 Unfortunately, these data appear to reflect heat losses which may have obscured some of the effects of increased pressure. The underground combustion processes are exceedingly complex, and general concepts relating to them have necessarily been described in relatively simple terms. Particularly with regard to forward combustion, the interaction between multiphase fluid flow, heat transport and various rate mechanisms is so involved that to date a rigorous treatment is not available. In this paper a linear near-adiabatic system is described which was found capable of operating at pressures up to 1,000 psig and temperatures of at least 1,100 F. Using this equipment, experiments on both forward and reverse combustion were accomplished at elevated pressures and the data presented as a function of air flux or temperature. It will be assumed that the reader is familiar with the papers of Wilson, Wygal, Reed, Gergins and Henderson on forward combustion and that of Reed, Reed and Tracht3 on reverse combustion, so that it is not necessary to repeat the details of the two processes. EQUIPMENT AND PROCEDURE It was decided to study the effects of pressure over the interval 0-1,000 psig using a near-adiabatic system. Since satisfactory operation of such a system requires very thin tubing walls, it proved necessary to insert the entire combustion tube and heater assembly into a high pressure jacket in such a way that the internal tube pressure could be counterbalanced by pressurizing the annulus. This meant that the numerous heater and thermocouple wires had to pass through gas-tight seals that required considerable effort to maintain effective. An unexpected difficulty arose in connection with the nature of the annulus pressuring gas. It turned out that the composition of this gas critically affected the functioning of the adiabatic control system. Operation of the equipment at elevated pressures was not particularly difficult. The problems that did arise were a direct consequence of the large numbers of connections and seals involved. EQUIPMENT The equipment consisted of the combustion tube which fitted within the pressure jacket. This jacket was in turn mounted on a wheeled carriage which facilitated movement and provided for rotation of the

By S. J. Rothman, J. J. Hines, D. Rokop, R. Bastar

Self-diffusion has been measured along each principal axis of mosaic-structured and relatively perfect a uvaniuln single crystals. The anisotropy reported before,' D[loo] = D[001] » D[010 , has been confirmed. and is shown to represent volume diffusion. Diffusion along the dislocations in the imperfect crystals increases the measured value of D significantly without changingr either the shapes of the penetvation plots or the anisotropy. SINCE a uranium is orthorhombic, the diffusion coefficients along the principal crystallographic axes need not be equal. A previous measurement of self-diffusion in three mosaic-structured a uranium single crystals1 showed that Dil00| =D[001 >>D[010 This result was deduced from penetration plots similar to those in Fig. 1. That is, the plots for diffusion along [loo] and [001] were the straight lines expected from the solution of the diffusion equation for the boundary and initial conditions of the experiment, while the plot for diffusion along [010] was curved so that the part near X = 0 had a much steeper slope than the straight lines did. The observed anisotropy could have been due either to volume diffusion or to diffusion along the very large number of dislocations in such crystals, according to the model proposed by aart.' The authors of Ref. 1 argued that the latter possibility was unlikely, but did not exclude it. To settle the question, a simultaneous measurement of self-diffusion in mosaic-structured and mosaic-free crystals was carried out. This paper reports the results, as well as a measurement of the temperature dependence of self-diffusion in a uranium. EXPERIMENTAL The single crystals of a uranium used in this experiment are listed in Table I, together with other experimental details. '(Mosaic structured" here means crystals grown by solid-state phase change.3 The Laue spots from such crystals spread over about 6 deg of arc, which indicates that the density of dislocations is very large. "Perfect" crystals are ones grown by Fisher's grain-coarsening tehnique; the Laue spots from these are quite sharp,4 which shows that the dislocation density in these crystals is much lower. All of the crystals were made from high-purity uranium; a typical analysis is given in Ref. 1. The actual diffusion directions were within a few degrees of the nominal. The thin layer-sectioning method was used. The experimental techniques were similar to those described in Ref. 1, except the sectioning. Crystals Za, 2b, 2c, 4a, 4b, and 4c were sectioned on a lathe. Crystals 3a, 3b, and 3c were sectioned by grinding on glass plates, with 1 p diamond powder in butyl alcohol as the abrasive. The use of glass plates eliminated the crowning noted in Ref. 1, and the use of butyl alcohol as a lubricant simplified the chemical processing of the sections. Material from the sides of these three crystals was removed by spark machining before sectioning. The sectioning of crystals 4a and 4c was botched. A small cylinder of metal was extruded from the center of crystal 4a while turning off material from the side of the sample. Crystal 4c was misaligned by 2.1 x 10"3 cm because the dial gage jammed during the alignment. Notwithstanding these errors, useful data were still obtained from these crystals. The points

Jan 1, 1967

By Bengt Helmerson

A new tankhouse was started in January 1959 at the Copper Refinery of the Boliden Co., Skelleftehamn, Sweden. In early 1961 a semiautomatic machine for looping and straightening of starting sheets was introduced to substitute previous manual operations. The machine as well as consequent, racking and handling is described. Finally, economic benefits achieved and new constructions for the future are discussed. HISTORY Tankhouse operations at the Boliden Co. 's Smelter in Skelleftehamn started in 1932 on a scale that since then has been gradually increasing. In order to rationalize the operations, a new tankhouse was erected. It went into production in January 1959 and was designed for a yearly production of 35,000 metric tons at a current density of 16 amps per sq ft. Already from the beginning, however, the tankhouse has been run with a current density of 21.5 amps per sq ft, corresponding to a maximum capacity of 50,000 tons a year. During the time of planning of the new tankhouse, due consideration was given to the possibilities of mechanizing the operations. New ideas could be and were actually tested on full or pilot plant scale in the old tankhouse. In that way we developed a system for the cathode handling including washing, weighing, and transportation. A system using forklift trucks in combination with trailers and overhead cranes has been developed for transportation and racking of anodes and also for handling of anode scrap. With respect to the electrolyte, circulation and temperature control are partly automatic. Special attention was paid to the production of starting sheets, which operation normally requires a great number of man hours, and it was made the object of a particular survey as to the best ways of straightening starting sheets, attaching loops to the sheets, and so forth. As a result, a machine was designed during 1957-58 and built in our own shops. After a period of tests, the new equipment was put in operation commercially on the 10th of April, 1961. Since this date the machine has produced about 2 million starting sheets without interruption and has been the only source of looped starting sheets for the tankhouse. GENERAL DESCRIPTION Fig. 1 shows all the major parts of the system. These parts are: slitting machine with feeding table (I), standard roller leveler, type Ungerer (2), tilting roller table (3), conveyors for sheets and suspension bars (4, 7), storage of suspension bars (51, punching and stitching machine (6), two lift-turn-tilt tables (8) for discharging the starting sheets, two rack conveyors (9) for sheet assemblies. Included are a hy-daulic pump station and panels for pneumatic and electric controls. SLITTING AND STRAIGHTENING The machine is fed by hand by a man sitting in front of the slitting-machine table, Fig. 2. This operator inserts one sheet at a time into the slitter. After being trimmed, the sheet is automatically conveyed to the following step of handling, straightening. The slitting machine cuts away about 8 mm of the upper and lower parts of the sheet (in relation to its original position in the stripper section) for two reasons. The first one is to give the machine sheets of uniform dimensions; the second one is a matter of quality. Normally the starting sheets as stripped have a thick edge at the bottom end. This part would collect anode slimes and might also cause short circuits when inserted in the cells without trimming. The straightener used is of German construction

Jan 1, 1967

By R. Simon, L. Yarborough

This paper presents a correlation for predicting the critical pressures of gas-solvent-reservoir oil systems of the type encountered in gas and solvent injection processes. Experimental data from 14 systems were used to develop the correlation which expresses critical pressure as a function of composition, C7+ mol weight, and C7+ characterization factor. Critical pressures predicted by the correlation for the 14 gas-solvent-reservoir oil systems have an average deviation of 2.8 per cent of the experimental values. The correlation war used to study a wide variety of other hydrocarbon mixtures reported in the literature whose critical conditions are in the range of interest in oil recovery work (100 to 280F and 2,000 to 6,000 psia). Critical pressures predicted by the correlation had an average deviation, expressed as per cent of experimental value, of 5 per cent for 20 miscellaneous mixtures from the literature, and 6.4 per cent for I7 methane-butane-decane mixtures reported by Sage and Lucey. INTRODUCTION Predicting critical points of hydrocarbon mixtures is an important part of phase behavior calculations. If the critical point can be predicted for a specific mixture, the separation between the bubble-point and dew-point regions will be defined, and physical properties of the mixture can be calculated by using the principle of corresponding states. Numerous correlations for predicting critical points of hydrocarbon mixtures have been published. Six of these correlationsl-8 were for light hydrocarbons, and two correlations7,8 ere for high boiling-point petroleum distillates. Organick9 And Eilerts" presented correlations which combined the published data from both light and heavy mixtures, and these correlations became the only available methods for predicting critical pressures for wide boiling range mixtures. In the course of the authors' work on secondary recovery by gas and solvent injection, experimental data were obtained for 14 mixtures of dry gas, ethane-propane-butane solvents, and various reservoir oils. The critical pressures and critical temperatures of these gas-solvent-reservoir oil systems were in the range of 1,900 to 4,800 psia and 180 to 265F. The critical pressures predicted for the 14 mixtures by the correlations of Organick and Eilerts had an average deviation from the measured values of about 13 per cent. The authors felt that it was necessary to develop a better correlation for engineering calculations and the resultant correlation, which is presented on Figs. 1 and 2, predicts the critical pressures of the 14 mixtures with an average deviation of 2.8 per cent. The validity of the correlation was tested by applying the correlation to other hydrocarbon mixtures reported in the literature. This subject is discussed later in the paper. The authors feel that there is also a need for an improved critical temperature correlation for gas-solvent-reservoir oil systems. However, developing a critical temperature correlation is a significant study in itself and is not included in this paper. EXPERIMENTAL DATA The compositions and critical points obtained by the authors for 14 gas-solvent-reservoir oil mixtures are shown on Table 1. The methane concentrations in these mixtures varied from 20 to 63 mol per cent. The intermediate hydrocarbon group, consisting of ethane, propane, and butane, varied from 20 to 64 mol per cent, and the concentration of the C,, fraction from 10 to 20 mol per cent. The physical properties of the C,, fraction covered the range from light, paraffinic, nonasphaltic (Mixtures 5, 6, 7, 8, 9 and 10) to heavy, aromatic, and asphaltic (Mixtures 13 and 14).

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the Ger- man techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low- cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first German assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission- to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high- cost coke and anthracite for the production of water gas. Although varying degrees of success have been achieved and the water gas produced generally has been higher in calorific value, in only a few isolated in- stances has there been any sustained use of bituminous coal for water-gas production for public utility uses after the shortages of anthracite and coke have been lessened.

Jan 1, 1946

By C. H. Samans, G. F. Tisinai

HARDENING and embrittlement of the ferritic chromium stainless steels at temperatures near 885 °F have been known for a long time.' However, no satisfactory explanation has been given. Both ordering and precipitation hardening have been suggested. Fisher, Dulis, and Carroll2 discovered a chromium-rich body-centered-cubic precipitate in embrittled alloys. Subsequently, Williams' and Wright4 also have found evidence of this body-centered-cubic constituent. William's hardness, electrical resistance, and magnetic studies led to his proposal of a new constitutional diagram for the Fe-Cr alloys. The new feature of this diagram is the eutec-toidal decomposition, below about 970°F, of the s phase into two stable body-centered-cubic solid solutions, one rich in iron and the other rich in chromium. An observation of Heger5 that the amount of s phase has increased and the amount of chromium-rich body-centered-cubic phase decreased in the interval 5000 to 32,600 hr at 900°F, even though the alloy increased in hardness, casts some doubt on this diagram. If precipitation hardening causes the embrittlement, the precipitate probably is always coherent with the matrix, since no evidence of overaging has been reported. It cannot be stated positively, however, that Fisher's body-centered-cubic constituent is the embrittling phase. According to Preston's data,6 such a chromium-rich phase should have a parameter less than about 0.5 pct larger than that of the iron-rich matrix lattice. Moreover, the constitutional relationships whereby Fisher's constituent forms, and whether it is stable, metastable, or a transition phase, are not yet completely clear. The recent studies of Wright4 and of Lommel,7 as well as the earlier studies of Becket8 and of Hochmann,9 have shown that 885°F hardening occurs in relatively pure Fe-Cr alloys. No evidence of its occurrence or absence in chromium itself has been reported. The rate of hardening in high purity alloys seems appreciably slower than that in alloys containing larger amounts of impurities (chiefly carbon and nitrogen). This may be due merely to the absence of hardening and straining effects from precipitated carbides and/or nitrides. These observations on high purity alloys make it seem unlikely that 885 °F hardening is caused by a constituent containing other than iron and chromium atoms, e.g., carbides and/or nitrides. Wright,4 Lommel,7 and Lena and Hawkes10 emonstrated the accelerating effects of a finely dispersed precipitate of (probably) chromium nitride on the hardening reaction. This appears to be evidence that lattice straining increases the rate of nucleation of the hardening constituent. Some new observations on 885°F hardening are reported here. They show an effect of preheat treatment that should contribute to a better understanding of the 885°F hardening phenomenon. They also clarify a discrepancy which exists in the literature. Some investigators have reported most rapid hardening at 885", whereas others have reported it at 930°F. The present work also shows that 885°F hardening does not occur in electrolytic chromium, and that any long range ordering type of reaction affecting any sizeable part of the volume is unlikely. Materials Studied Table I shows the currlposition of the alloys used in this investigation. In these alloys carbon and nitrogen are present in roughly similar amounts. Presumably both elements precipitate, as carbides and/or nitrides, during the heat treatments given.

Jan 1, 1958

By Carlos E. Roggero

The influence of high temperatures on the zinc roasting practice has been investigated by full-scale tests in fluid bed reactors operating at temperatures from 950° to 1150°C. It was definitely shown that, throughout the range, an increase in tem perature resulted in a 2 to 3 pct increase in zinc solubility because of decreased content of zinc fer-rite and lowered sulfide sulfur. The former is attributed to thermal decomposition of ZnFe,O,, and the latter to increased oxidation rates, ad longer retention times. Data on the gveatly increased volatilization of lead, cadmium, and silver above 1000°C, are presented. A considerable fraction of the iron present in the feed was also transferred at high temperatures from the coarse roaster discharge to the flue dusts. AS part of its metallurgical complex1-3 situated in a 12,000 it Andean valley at La Oroya, Peru, Cerro de Pasco Corp. (a wholly owned subsidiary of Cerro carp.) operates a 150 short ton per day electrolytic zinc refinery. Electrolysis is carried out at a cathode current density of 65 amp per sq ft with an electrolyte content of 55 g per liter of Zn and 150 g per liter of su lf uric acid. Due to the high iron content of the marmatitic concentrate used, a large fraction—about 15 pct—of the zinc reports in the leach residues. To minimize such losses, efforts have been exerted toward improving calcine solubility. One method, as noted in the literatre,, is to retard zinc ferrite formation by decreasing the roasting temperature. Unfortunately, such a procedure tends either to reduce the roaster throughput or increase the sulfide sulfur in the calcine. Consequently, this approach was discarded in favor of experimental work in the opposite direction, i.e., high temperature roasting. Full- scale tests were promising and resulted in the granting of a patent to Cerro de Pasco carp.' After a brief account of plant equipment and operating procedure, this paper describes the tests made and attempts to assess the results obtained. GENERAL PLANT LAYOUT AND OPERATION The Roasting Plant, see Fig. 1, comprises an agglomerating plant feeding three fluid bed roasters with a combined capacity of 10,000 tons per month. The Peruvian patent rights on this process were purchased from the New Jersey Zinc Co. The concentrate, assaying: is pelletized to a -3 +14 mesh product and fed to the fluid bed roasters. The roaster exhaust gases pass through a waste heat boiler, cyclones, a fan, and an electrostatic precipitator. Approximately half of the dust collected in the cyclones returns to the pellet-izing plant as one of the binding ingredients, the remainder joins the cooled bed discharge ('overflow') and is conveyed to the grinding plant. The -35 mesh product obtained, together with the dust collected in the electrostatic precipitator constitute the feed to the leaching plant. Batch leaches are made in vessels with mechanical and air agitation, the residues are separated and washed in Burt Filters, and pumped to storage ponds. THE FLUID BED ROASTERS Two reactors are as shown in Fig. 2, and the third,' of about the same configuration, is approximately 40 pct smaller. The total grate and freeboard (just below the gas outlet) areas measure 170 and 426 sq ft respectively. The feed, continuously weighed and controlled by Merrick Weighto-meters fitted with variable speed motors, enters the reactors at the top of the expanded bed level. The coarse calcine overflows through the opposite end by

Jan 1, 1963

By J. W. Martin, L. K. Singhal

Grain boundary M23CB precipitates have been shown to form by a process involving the migration of an austenite grain boundary, and each plate of precipitate is in parallel orientation with one of the austenite grains constituting the boundary. The carbide distribution and morphology appear to be sensitive to grain boundary mis orientation. Some areas of austenite grain bowzdary permit the development of an array of M,C, particles, some of which are in parallel orientation with one grain and some with the other grain constituting the boundary. Massive carbide at grain boundary triple points is also shown to be in parallel orientation with one constituent grain. PREFERENTIAL precipitation during aging of carbides of the type (Fe,Cr)23C6, usually written MZ3C6, in grain boundaries of quenched austenitic stainless steels has been widely recognized. M23C6 has a complex cubic crystal structure' which contains ninety-two metal atoms and twenty-four carbon atoms per unit cell. Less energy is involved in forming grain boundary precipitates than in the formation of intragranular precipitates, and the process is further enhanced by the accelerated diffusion rates in the boundaries and by the probability of segregation of chromium atoms and carbon atoms to the region of the grain boundaries during prior solution heat treatment in order to reduce lattice strain. Early electron micrographic studies2, 3 involving either extraction replica or normal replica techniques established the geometric or dendritic form of the carbide particles, although this approach led to dis- pute as to whether the particles grew within the plane of the boundary or grew into the matrix.4-6 More recent thin-foil studies' have claimed to identify a discontinuous precipitation process involving M23C6 at grain boundaries, and the object of the present work was to attempt to clarify the situation using modern electron micrographic and diffraction techniques. 1) EXPERIMENTAL 1.1) Material. The steel selected for this work had a base composition of 24 pct Ni-25 pct Cr-3 pct Ti and contained about 0.04 pct C. The full analysis if given in Table I. This alloy was in the form of strip which had been hot- and cold-rolled to a thickness of 0.6 mm. 1.2) Heat Treatment. Specimens 4 cm long by 1 cm wide were solution-heat-treated for 3 hr in argon at 1150°C, followed by water-quenching. Specimens were subsequently aged in vacuo at 750°C for periods up to 500 hr. 1.3) Preparation of Electron Microscope Specimens. The heat-treated strips were cut bv spark machining into discs of 3 mm diam and 0.6 mm thickness. he-discs were dished on both sides using an electrolytic jet of 15 pct HCl electrolyte at 80 v. Final electro-polishing of the discs was carried out using 10 pct perchloric acid, 20 pct glycerol, and 70 pct ethanol at 10 v. The current density was kept below 300 ma. cm"2 by cooling the electrolyte to 0" to 5°C. As soon as a small hole appeared, the electropolishing was stopped and the specimen was quickly washed with ethanol.

Jan 1, 1969

By K. K. Kershner, W. A. Calhoun, C. W. Funk

Future resources of aluminum may require the utilization of low grade ores to provide a more permanent protection for the nation. Aluminum minerals such as cloy, shale, and high iron laterites may become important sources. An evaluation of reserves is given. New laboratory results are reported on the Vereinigte desilication process. THIS report on future resources of aluminum metal emphasizes the necessity for investigating utilization of low grade potential ores to provide more permanent protection for the nation. Partial or complete interruption of the importation of high grade aluminum ores must be given consideration. Ultimately, aluminum minerals such as clay, shale, and high iron laterites may become the principal sources of aluminum. The development of extractive processes for treating these low grade materials is a step in long-range national preparedness that should receive more attention. In formulating such processes, the application of beneficiation methods for the purpose of classifying the several types of minerals before subjecting each type to the more expensive extractive procedures should be considered, and a careful survey of the basic factors of power sources, transportation facilities, and sources of raw material should be made. Domestic Bauxite Resources Of the domestic supply of current, treatable-grade bauxite, 95 pct comes from Arkansas. The present reserve of Arkansas bauxite suitable for metal production, including abrasive-grade, Bayer-grade, and modified Bayer-grade ores, is 34,000,000 tons. The total reserve of bauxite of all grades is approximately 75,000,000 tons. Reserves are estimated on a mined and dried basis. Data available to the Bureau of Mines in 1948 to 1949 were used in preparing Table I, which shows a breakdown by grades of bauxite for about a half of the reserves of the state. The modified Bayer ore, 10,555,500 long dry tons, is based on a cutoff of 8 to 15 pct silica. The sub- marginal 10,074,700 long dry tons is assumed to contain more than 40 pct gibbsite, more than 15 pct silica, and less than 32 pct available alumina. A considerable amount of this low grade material was consumed in 1949 and 1950. Additional tonnages of bauxitic and kaolinitic clays are indicated by the Bureau of Mines drilling project.' Applying a 50 pct factor to arrive at long tons mined and dried, the results of this project are approximately 31,500,000 tons kaolinitic clay at +35 pct Al²O3 and 11,800,000 tons kaolinitic clay at 20 to 35 pct A1,0,. Total reserves of kaolinitic clays are probably quite extensive—several times the reserves shown in the Bureau's work. Total reserves of bauxitic and high iron clays from the drilling program and previously established figures are 63,980,000 tons. The mineral dressing methods,' the lime-sinter process, he lime-sinter modification of the Pederson process," the lime-soda sinter process,"-' and the Alcoa combination processa. have been described in the literature and will not be elaborated upon here. The less familiar Vereinigte Aluminium-Werke process used by the Germans during World War 11 may require some amplification. It was used to bene-ficiate boehmite ores containing 12 to 18 pct silica for a feed to the European Bayer process. Ore was

Jan 1, 1952

By P. F. Gnirk, J. B. Cheatham

An experimental investigation has been made to study the effects of tooth angle and confining pressure on the force required for indentation of dry rock samples under confining pressure. In these experiments static single-tooth indentations were made on two standstones, a limestone, a schist and a slate under confining pressures of 5,000 to 15,000 psi. Sharp wedge-shaped teeth with included angles ranging from 30°to 105°were used. In all cases the force-displarenzent curves are approxinlately linear for rocks tested under confining pressure, as contrmted with the discontinuous curves obtained for silnilar rocks at atmospheric conditions. Photonzicrographs of thin sections through the craters indicate very little evidence of chip formation during indentation. In general the experimental data lie between calculated values for perfectly rough and perfectly smooth tooth-rock interfaces. INTRODUCTION The variables associated with ctrilling at depth are numerous and, in many instances, are not easity isolated and controlled. Also, many of these variables are interdependent; however, if the variables which are sufficiently independent of each other are held constant and are appropriately introduced, the dependent variables can be more easily studied and evaluated. It is the purpose of the present investigation to study experimentally the simplest case of bit tooth-rock interaction. In essence, the experiments have involved the static loading of sharp wedge-shaped tools on the surfaces of effectively semi-infinite dry rock samples subjected to confining pressures. During this investigation the following quantities have been maintained constant: 1. Pore pressure: atmospheric (i.e., the rock is dry). 2. permeability: although the rocks may be permeable, they are "jacketed" in such a manner that the fluid is not permitted to flow through them. 3. Temperature: 75F. 4. Rate of loading: essentially static (approximately 0.002 in./second). 5. Bit tooth: a sharp wedge-shaped tooth loaded normal to the rock surface. 6. Rock surface: smooth and flat. 7. Drilling fluid: hydraulic oil. In addition to the above conditions, the rock surface was free of a layer of cuttings. There was no indexing to previously indented surfaces, and the influence of corners of the borehole was neglected because the rock samples were effectively semi-infinite. The following quantities have been varied, and the resulting effects have been studied: 1. Rock a) Type (e.g., limestone, sandstone, etc.). b) Mechanical properties ) Necessarily dependent c) Porosity on type of rock. 2. Bit tooth (included angle of wedge-shaped tooth). 3. Depth of penetration. 4. cobfining pressure. On the basis of laboratory experiments which have shown that many rocks exhibit ductile behavior at confining pressures corresponding to depths usually reached during drilling,'.' a theory has previously been advanced which predicts the force required for penetration by a single sharp wedge tooth into a ductile* material.' The material is assumed to be isotropic, homogeneous and rigidly plastic (no elastic deformation) and to obey the Coubomb yield criterion (Figs. 1 and 2). Equations governing the force required for penelration are given for two extreme cases:** 1. A smooth, perfectly lubricated tooth-rock interface (fridionless boundary), in which the solution gives a minimum value for the penetrating force: in which F = force of the tooth, b = length of tooth edge,

By H. R. Stahl

The ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classi- fiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9½-in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 52¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1¾ in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges

Jan 1, 1947

By H. R. Stahl

The ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classi- fiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9½-in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 52¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1¾ in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges

Jan 1, 1947

By J. Wade Watkins, E. S. Mardock

The accurate evaluation of reservoir-performance characteristics in the secondary recovery of petroleum by water flooding requires use of a water tracer that may be injected into water-input wells and detected at oil-production wells to supplement data obtained from core analyses, wellhead tests, and subsurface measurements. Radioactive iodine has been used successfully as a water tracer in field tests to determine: (I) relative rates and patterns of flow of injected water between water-input and oil-production wells and (2) zones of excessive water entry into oil-production wells. Laboratory evaluations of potential water tracers, previous tracer studies, the value of using a radioactive tracer, general field procedures, and the use of surface and subsurface instruments for the detection of the emitted gamma radiation, are summarized. Data from the field tests are presented graphically and discussed in detail. It is concluded that the radioactive-tracer method, using radioactive iodine, may be used successfully to measure either the relative rates and patterns of flow or zones of excessive water entry into wells under conditions of comparatively rapid transit time between wells. INTRODUCTION Extensive use is made of data obtained from core analyses, wellhead tests, fluid characteristics, and subsurface measurements in evaluating the sweep efficiency of water injected into oil sands for the recovery of oil. Theoretical flow rates and patterns may be calculated from those data using radial-flow formulas, if it is assumed that the physical conditions in the productive formation are homogeneous. Unfortunately, homogeneous conditions rarely, if ever, exist in oil-productive formations. The use of a tracer that may be injected into an oil sand and detected quantitatively, or even qualitatively, at offsetting oil-production wells provides basic data that may be used in determining more accurately the subsurface rates and patterns of flow of injected water between wells than is possible by theoretical calculations based on assumed conditions. Consideration of the data obtained by using a water tracer assists in the application of remedial measures to water-input wells, such as plugging of channels, or selective plugging of highly permeable zones, thereby effecting a more uniform flood and a greater ultimate oil recovery. A water tracer should have the following characteristics: (1) low adsorption on solid reservoir material; (2) high solubility in water; (3) low or negligible solubility in crude petroleum; (4) a wide range of solubility of compounds that may be formed by chemical reactions with ions present in reservoir rocks or waters; (5) high detectability in low concentrations by portable apparatus; and (6) general availability at low cost. Additional desirable characteristics are that the tracer should be nonhazardous in nature under normal working conditions and quantitatively detectable in the well bore, as well as at the surface. Review of Previous Tracer Studies The need for a water tracer has been recognized for many years. As far back as 1906, Dole1 described the use of fluorescein in flow-rate studies made in France in 1901. In 1921, Ambrose" discussed in detail the use of organic and inorganic dyes, chlorides, nitrates, and other anions, lithium salts, and the Slichter electrical

Jan 1, 1955

By J. S. Kasper, R. M. Waterstrat, B. F. Decker

THE existence of v phase in the Mn-Mo system was discovered in this laboratory several years ago,' but neither the conditions of its formation nor its composition were known, and preliminary attempts to reproduce the phase were unsuccessful. We wish now to specify the information appropriate to phase formation on the basis of experiments performed since that time. The starting materials were in every case electrolytic manganese and high purity molybdenum. Two methods of preparation were employed: l—arc-melting varying combinations of the elements in an inert atmosphere and subsequent heat treating, and 2—sintering compressed mixtures of finely divided powders of the elements. In the latter method, the powders were first passed through 200 mesh screen and then compressed into cylinders of % in. diameter and % in. length, which were sintered at elevated temperatures in an atmosphere of dry hydrogen. For some samples, the sintering temperature was 1200°C (for 1 hr), and these were then heat- treated at lower temperatures for times up to 24 hr. Eventually it was found, for the proper composition, that essentially pure a phase could be produced by sintering at 1125°C for 3 hr. Quenching to room temperature was effected by means of a stream of cold, dry hydrogen in a water-cooled chamber. The arc-melting procedure was found to be unsatisfactory after an investigation of many samples at different compositions and temperatures. Large quantities of manganese were vaporized during melting and none of the products were homogeneous or contained extended regions of pure phase. Nonetheless, these experiments established that no formation occurs in the Mn-Mo system below 1115oC, and indicated, at least roughly, the composition range of interest for further exploration. The more definite results obtained from samples produced by the second method are given in Table I. A portion of sample 2 heated for 16 hr at 1000°C in a Vycor tube transformed to molybdenum plus unidentified phases of complex X-ray pattern. From these few results it appears that the region of phase is quite narrow in composition. It is of interest that the composition is such as to make for difficulties in correlating this structure on an electron atom basis with other a structures of iron, cobalt, and nickel. In that respect Mn-Mo shows the same anomaly as Mn-Cr and Mn-V systems.' A second feature is that in common with the two other known molybdenum (Fe-Mo and Co-Mo), Mn-Mo v exists only at elevated temperatures. The X-ray powder pattern of the pure a phase of Mn-Mo is given in Table 11. It agrees well with the patterns established for other structures, especially with that for Fe-Mo as given by Goldschmidt.An attempt is being made to establish whether an ordering of the respective atoms occurs and such information will be reported in a future publication. Acknowledgment The authors acknowledge gratefully the assistance of Mrs. J. R. Belanger in some portions of this work. References 'J. S. Kasper, B. F. Decker, and J. R. Belanger: Journal of Applied Physics (1951) 22, p. 361. 2 A. H. Sully: Journal Inst. Metals (1951) 80, p. 173. H. J. Goldschmidt: Research (1949) 2, p. 343.

Jan 1, 1954

By S. I. Liu

THE effects of strain histories, consisting of several prestrains in opposite directions, on the flow and fracturing characteristics of metals determined in a final test have been investigated previously.'" Such strain histories vary from a single prestrain in tension or compression to the number of strain cycles leading to fatigue failure.' Between these two limits, various strain histories could be visualized and some can be attained readily. One such example is a strain history consisting of a first prestrain in tension of various magnitudes and a second prestrain in compression also of various mag-nitude. In this investigation the strain history was extended to the combination of these two limits, i.e., a single prestrain in tension or compression followed by balanced strain cycles of a selected magnitude e, = k0.12. It was found in this case that only compressive initial prestrains could be investigated with sufficient accuracy.* Such strain histories can be considered also as (low cycle) fatigue tests of a metal subjected to various amounts of cold working. It appears from previous publications that cold working within a wide range of reductions usually raises the un-notched fatigue strength of many metals.'-' This effect, however, has been found to be inconsistent and sometimes reversed for other metals?.7 Furthermore, Ludwik reports that the yield strength of cold-worked specimens may be reduced by cyclic strains, while that of materials without cold work is generally increased in the initial cycles." " In addition to the above tests, a study was made of the effect of intermediate re-solution heat treatment on low cycle fatigue behavior. Such anneals should eliminate the strain hardening induced by the cyclic strains. As far as their effect on the fracture characteristics is concerned, a few previous tests seemed to indicate that the damage resulting from cyclic strains is retained only partially after heat treatment." A further investigation was made in which one specimen was subjected to repeated unbalanced tension cycles in which the strain interval was approximately $ 0.013. This repetition of plastic tension damages the material slightly. This result appears to confirm Ludwik's observations." " Commercial 3/4-in. rod of the aluminum alloy 24ST4 was selected for this investigation. The material was subjected to the following treatments before machining: 1—Re-solution treatment at 920" ± 10°F for 45 min, 2—water quench at room temperature, and 3—aging for four days at room tem-perature.? The treated material then was machined to desired specimen contour and tested. A coolant was used during machining to minimize any artificial aging effects of heating during machining. In some cases the 24ST4 specimens were reheat treated after having been strained. In these cases, the heat treatment was the same as the re-solution heat treatment described above. Procedure As shown in Fig. 1, threaded end specimens with a minimum diameter of 0.266 in. and a contour radius of 2 in. were used for prestraining to an axial compressive strain ranging from 6, = —0.10 to E, = —0.48. For large prestrains, two consecutive corn-

Jan 1, 1952

By S. R. Goodman, Hsun Hu, R. S. Cline

The quenching technique has been used to study phase relations in the composition area 2FeO.SiO2-FeO-SiO2-MnO.Si02-ZMnO.SiO2 of the system iron oxide-manganese oxide-silica under strongly reducing conditions such as exist in a gas mixture consisting of equul parts of carbon dioxide and hydrogen. Liquidus and solidus temperatures of most mixtures in the composition area studied are in the range of 1173° to 1345°C. EQUILIBRIUM relations existing among the oxides of iron, manganese, and silicon are of particular interest in two areas of steelmaking: slags and ingot inclusions. Mixtures of these oxides represent about 90 pct of the slag in the acid steelmaking process, and so dominate the chemistry of the whole refining process. These constituents also play an important role in the early slags existing at the time of the "lime boil" in the basic open hearth process. If these slags are liquid, they "wet" the lumps of lime rising from the bottom of the bath, and react with them. A liquid slag rich in CaO is then formed at the very beginning of the refining. Because the temperature is still low, all conditions for a good dephosphoriza-tion are fulfilled at this stage of the operation. Metal deoxidized with ferromanganese or silico-manganese is likely to contain, as inclusions, phases made up from among the oxides of iron, manganese, and silicon. A knowledge of stability relations existing among the phases present in this system, therefore, enables one to predict the hardness of the inclusions encountered. Moreover, because the shape of the inclusions in steel has a profound influence on the physical properties of the metal, it is important to establish whether or not the oxidic material is present as liquid or crystalline phases during heating and rolling of the steel (-1150 to 1350°C). A knowledge of melting relations in synthetic mixtures of iron oxide, manganese oxide, and silica will give a clue to these problems. Methods for determining such relations and the results obtained are described iln this paper. I) PREVIOUS WORK A number cf previous studies have dealt with the three "binary"* systems bounding the system iron oxide-mangar,.ese oxide-silica. The system iron oxide-silica was studied by Bowen and shairerl in 1932. Their data were obtained by equilibration of mixtures in contact with metallic iron. Phase relations for the system iron oxide-silica ill atmospheres of different oxygen pressures car1 be derived from data on the system FeO-Fe2O3-SiO2 as determined by Muan.2 The diagram shown iri Fig. l is a section of this system in an atmosphere of CO2 and H2 in ratio 1:l. The system manganese oxide-silica has also been the subject of several investigations. Most of the early studies suffered from a lack of proper control of the atmosphere under which the equilibrations were carried mt. Phase diagrams for the system at two well defined levels of oxygen pressures have been determined recently. Glasser3 determined stability relations in an atmosphere consisting of carbon dioxide and hydrogen in ratio 5:1, diagram Fig. 2, and Muan4 studied phase relations in the system in air.

Jan 1, 1962

By N. K. Chen, C. H. Mathewson

Single crystals of high purity aluminum of various orientations were carefully documented after plastic extension. Special attention was given to the formation of slip lines, deformation bands, and asterism. An explanation for the geometry and mechanism of formation of deformation bands is considered. WHILE the general process of plastic extension of face-centered cubic metals is well understood,' the accompanying structural changes due to slip and rotation are far more complex than ordinarily assumed. In the case of stretched single crystals of aluminum, the complicated behavior is especially marked by the formation of deformation bands, as first indicated by Collins and Mathewson." Such bands were believed by them and also by others,".'7 who have discussed banded structure in general, to represent one of the important modes of lattice reorientation and to be intimately connected with the recrystallization process. Yet, despite their fundamental importance to the understanding of the mechanism df both plastic deformation and recrystallization, practically no study of the crystallographic features of these bands in their relationship to the conventional slip process has been attempted. This paper describes part of an extensive investigation on the structural behavior during plastic deformation of aluminum single crystals and is especially concerned with the characteristics of deformation bands. The investigation of the subsequent re-crystallization of deformed aluminum single crystals will be discussed in a later publication. Experimental Procedure Single crystal specimens of 99.996+ pct pure aluminum, Yz in. in diam and 5 to 6 in. in length were made both by the Bridgman method5 nd by a modified temperature gradient method.'* Crystals were selected in which the lineage deviation did not exceed 2"; i.e., as determined from the back-reflection Laue X-ray photograms. These crystals were radiographed to insure that no internal porosity was present. The orientations showed good coverage of the whole area of the Taylor and Elam triangle.' Orientations of the crystals were obtained by the back-reflection Laue technique described by Greninger." Crystals so selected were tapered very carefully in a lathe to obtain a linear decrease in diameter from 0.500 to 0.350 in. along a gage length of 3 in. This is considered desirable because it permits a strain gradient to be introduced in a single specimen at one initial orientation. The advantages of tapered crystals for studying the development of slip lines and recrystallized grains have been pointed out by previous investigators." The cold-worked layer resulting from the machining operation was removed by alternate etching in aqua regia and careful polishing with 2/0 emery paper until undistorted Laue back-reflection spots were obtained. A homogenization treatment at 600 °C for 24 hr was then introduced to insure the removal of residual stress. Two of the crystals so prepared were also checked by use of a glancing angle technique. Using a copper target, at 30 kv and 10 microamperes, a monochromatic beam was positioned at right angles to the axis of the crystal about which it rotated. The time of exposure was 24 hr. From these X-ray photograms, it was concluded that the present method of preparation of single crystals is satisfactory. Following this procedure, the crystals were elec-trolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. Intermittent

Jan 1, 1952

By R. B. Rosene, G. L. Foster, A. R. Hendrickson

he properties of some of the common fracturing oils, such as sand-falling rate, fluid loss and viscasity, are a function of the three major constituents of the oil. These are: asphaltic material, parafin waxes and a base oil. The base oil can be either high or low viscosity. Asphaltic material increases viscosity by thickening the oil, decreasing the rate of fall of sand through the oil. at temperatures up to 200" F. When large arnorrnts of parafin wax are present, much of the wax i.s not dissolved, but is present in the form of rnicroscopic crystals. 7'his, of course is limited to temperatures below the melting points of waxe.s. As a result, parafin waxes clo not function primarily as thickener.7, but rother as bullting materials. The functiori of wax, without asphaltic material, in a low viscosity base oil is uniquely unlike that of wax with asphalt coexistent in the oil. The resulting difierence in wax crystal size governs the sand-falling rate to a large extent. An ideal type of fracturing oil is one containing neither asphalt nor waxes. In such cases, the viscosity and resulting low sand-falling rate are apparently due to soluble resin- ous hydrocarbons, which are compatible with formation oils. INTRODUCTION Since the introduction of hydraulic fracturing as a method of stimulating production from oil and gas wells, a variety of fluids have been employed to open the fractures and carry the propping agent. Such fluids include gels, emulsions, and oils. In the latter category, the use of refined oils has increased tremendously, and it is probably safe to assume that such oils represent more than one-half of the total fluid used in fracturing. The general acceptance of refined oils for fracturing can be accounted for on the basis of their relatively low cost and general applicability. To minimize transportation costs, such refined oils are generally obtained within the local areas of operation. As a result there are several kinds of oil used in different areas, with a wide variation in the basic composition. These types may vary from a fair grade of lubricating stock to a highly viscous cut-back asphalt. or road oil. Originally, little attention was paid to the composition of the oils used for fracturing, and any oil which would carry sand was considered satisfactory. Recently, however, service companies and well operators have become more concerned with the type of oils used for fracturing. With this in mind, the present work was undertaken to evaluate and compare many widely used fracturing oils to determine which constituents were most desirable for fracturing purposes. Some of the important properties of fracturing fluids are sand-falling rate, viscosity, and fluid loss. Other properties, that are actually of no less importance, include flash point, pour point, emulsifying tendencies with formation brines, and compatability with the formation oils. This discussion has been limited, however, to the first mentioned properties in order to give some idea of the general composition of the refined oils, how they function, and why. PROPERTIES OF FRACTURING OILS The properties of fracturing oils are a function of the three major constituents of the oil. These may be designated as: (1) asphaltic material, (2) paraffin waxes and (3) a base oil, which may be of either high or low viscosity. The asphaltic material clas-

Jan 1, 1956

By N. V. Peterson, R. S. Mason

The violent explosion of Mount St. Helens in the state of Washington on May 18, 1980 showered volcanic ash over vast areas of the Northwest. It was another eruptive episode in a long history of similar occurrences in the region, which extends from Canada to California and reaches several hundred miles inland from the Pacific Ocean. Pumice, pumicite, and cinders are products of explosive volcanic eruptions. Pumice and pumicite are produced by the violent expansion of dissolved gases in a viscous silicic lava such as rhyolite or dacite. Scoria is the mafic counterpart of pumice. Pumice is a light-colored, cellular, almost frothy rock made up of glass-walled bubble casts. It may occur as coherent, massive blocks composed of highly vesicular glassy lava in either a flow or vent filling, or it may be more or less fragmented by violent eruption. Pumicite, the diminutive of pumice, has the same origin, chemical composition, and glassy structure, differing only in particle size. Particles less than 0.16 in. in diam are designated pumicite. Pumice usually is found relatively close to the vent from which it was expelled, while pumicite may be carried by winds for great distances before settling as an accumulation of fine-grained ash or tuffaceous sediment. Mount St. Helens lofted an estimated 5 billion cu yd of ash and pumicite. The volcano, unlike most of the High Cascade peaks, is composed largely of dacitic material with only minor amounts of andesite and basalt. Volcanic cinders are the reddish to black vesicular fragments which pile up during explosive eruptions of volcanoes of basaltic composition. Most cinder deposits occur as cones or mounds of stratified fragments ranging from a fraction of an inch to several inches in diameter. Individual cones or mounds may be several hundred feet in diameter and up to 500 ft high. Properties and Uses Low bulk density, good heat and sound insulating properties, and excellent abrasive capabilities make pumice and pumicite useful in industrial applications. Cinders, though less cellular and somewhat heavier, also have a variety of industrial uses. The main use of pumice and cinders continues to be in the construction industry as road-surfacing material, railroad ballast, and building block aggregate. Pumicite is used in sizable quantities as a pozzolanic additive to monolithic concrete where it increases workability, strength, and durability of the concrete and reduces the heat of hydration. Volcanic cinders generally are denser and more coarsely cellular than most pumice. Markets for cinders include aggregate for road construction and surfacing and use in lightweight concretes, particularly blocks. Some producers having access to both pumice and cinders offer a variety of blends of the two materials to block manufacturers. Table I lists the principal applications of industrial pumice. Tables 2 and 3 show US sales and uses of volcanic products. Most pumice deposits are unconsolidated and usually have a minimum of overburden. Mining is by open pit and can be easily carried out with conventional loading equipment. Sometimes air drying precedes hauling to a crushing and screening plant which yields the size product desired. Multiple bins at railroad hauling facilities permit blending if desired. Pumice for abrasive use may require more sophisticated processing by fine grinding and air classification before being bagged for market.

Jan 1, 1983