Search Documents

By J. Kittl, D. Arias

THE decomposition on cooling of the high-temperature ß bcc phases in copper- or silver-based binary systems usually takes place by a martensitic. massive, bainitic, or pearlitic reaction depending upon the particular conditions of each system. The AgAl system is one of these systems in which a massive or a martensitic transformation can occur upon cooling from the 3 phase field. Recently Hawbolt and Brown1 observed both massive and martensitic transformation products in a 22.7 at. pct A1 alloy. In the present work the massive and the martensitic transformations were investigated in a number of alloys for the composition range between 23.2 and 27.9 at. pct Al. The alloys were prepared using high-purity silver, 99.999 pct, supplied by ASARCO and aluminum, 99.999 pct, supplied by ALCOA. The metals were melted using a graphite or a sintered alumina crucible which was sealed in quartz tubes under an argon atmosphere. The alloys Were remelted to reduce segregation and homogenized in the 13 phase field for 24 hr. The weight of the alloys after homo-genization compared with the initial weight indicating the alloy composition to be within k0.1 pct of the in- tended composition. Chemical analysis of several samples confirmed the estimated alloy composition. All metallographic observations were performed on samples electropolished with ac current using a 10 pct solution of KCN and a stainless-steel electrode. The samples were cut into -1-mm-thick slices, polished, heat-treated in the ß phase field, and quenched in air, ice water, or iced brine. Some heat treatments consisted of a 2-min anneal carried out in air to allow maximum quenching speeds. Other samples were heat-treated in a vacuum of 10"4 torr and quenched using a helium blast in a quenching apparatus described elsewhere.&apos; In both cases, no appreciable losses of silver or aluminum were noted at the sample surface by sectioning and electropolishing. Table I summarizes the microstructure resulting from the various quenching treatments. The composition of the alloys investigated is also indicated on the equilibrium diagram in Fig. 1. The <, hcp phase, typical of a massive ß — cm, transformation, was observed in all alloys. A minimum temperature of 450°C was estimated for this transformation based on preliminary cooling experiments. the results being included in Fig. 1. In these

Jan 1, 1970

By Sheldon Rideout, E. L. Kamen, B. S. Lement, Paul A. Beck, W. D. Manly

The 1200°C isothermal sections of the following ternary phase diagrams were investigated: Cr-Co-Nil Cr-Co-Fe, Cr-Co-Mot and Cr-Ni-Mo. In all these systems the u phase was found to form extended solid solutions. Two new ternary phases of unknown structure were identified. The existence range of intermediate phases of transition elements was correlated with 3d electron vacancy concentrations. THE occurrence of extensive ternary d solid solutions in the Cr-Co-Ni and in the Cr-Co-Fe systems was described in a brief note.&apos; More recently d- solid solutions were also found in the Cr-Fe-Mo system by two independent groups of investigators.2,3 The existence of binary d phases in the V-Co and V-Ni systems, predicted in ref. 1, was experimentally discovered recently by Duwez and Baen and independently by W. B. Pearson, J. W. Christian, and W. Hume-Rothery.5 Duwez and Baen stated two general conditions for the occurrence of the d phase in alloys of the transition elements: "(1) The atomic diameters of the two metals do not differ by more than 8 per cent. (2) One of the two metals has a body-centered cubic structure while the other is face-centered cubic, at least in one of its allotropic forms." In the course of an extensive research program conducted at this Laboratory under the sponsorship of the NACA, several ternary systems, containing d solid solutions and also certain new ternary phases, were investigated. The present report describes the investigated portions of the 1200°C isothermal sections of the following ternary phase diagrams: Cr- Co-Ni, Cr-Co-Fe, Cr-Co-Mo, and Cr-Ni-Mo. It was found that the range of existence of the d phase in these four ternary systems, as well as in one of two ternary systems which were investigated by others, can be fairly consistently described in terms of electron vacancy concentrations. This supports the suggestion of Sully and Heal" that the d phase is an electron compound. Experimental Procedure The ternary alloys were prepared by vacuum induction melting in zirconia and alumina crucibles. Lot analyses of the metals used are given in Table I. Specimens of all alloys were annealed at 1200°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. Alloys consisting mainly of

Jan 1, 1952

By William Romanoff

As you are no doubt aware, virgin copper, tin and zinc are strategic metals today and little, if any, is available in the manufacture of brass and bronze ingots. The source of alloys used in the manufacture of implements of war are, therefore, from ingots made almost exclusively from the refining of available scrap. It is amusing to hear of the unusual physical properties of various alloys because they mean nothing unless the foundryman is able to produce good sound castings. A discussion therefore means little unless something is said about the relative foundry practice of the various brass and bronze alloys. Among the factors that influence the quality of castings produced are: (I) improper gating, (2) wrong pouring temperatures, (3) poor sand conditions, (4) bad melting practice, (5) faulty pattern equipment, (6) metal. It seems to be the consensus of opinion that about 95 per cent of defective castings can be attributed to the first three causes. Metal while a source of trouble at times, is probably the least responsible for foundry difficulties. As you all know, a molder never makes a bad mold. His first thought is to blame the "damn" metal as this is the path of least resistance. Let&apos;s consider the "damn" metal and how it is made. In the manufacture of ingot, scrap is collected at various sources and is shipped to the refiner either directly or through the scrap dealer or broker. It is usually sorted, although not always. In working toward a specified chemical analysis, weighed amounts of various grades of scrap metals are melted, and then oxidized by blowing air through the molten bath to rid the metal of detrimental impurities or reduce them to within specification limits after which they are skimmed off with the aid of some added fluxes. The bath of metal is then poled with wood, chemically tested before and after additions are made to bring it up to required specifications, and finally poured into ingots, after which a final chemical and physical examination is made. As mentioned above, the impurities have either been eliminated or reduced to the point where they meet the specifications of all Government Agencies or Technical Societies. Therefore, why worry as to whether castings are to be made from strategic virgin metals or secondary ingots from available scrap. Tests have continuously been made and it is a proven fact that physical properties are no better from virgin metals than from secondary ingots of the same composition. It is definitely more fool-proof to make castings from secondary ingot than from virgin metals because if an error is made in weighing the copper, tin, lead or zinc of the latter, the analysis is off balance. If an error is made in weighing secondary ingots, you merely have more or less metal but the analysis remains constant. Furthermore, when pure copper is melted. it is susceptible to reducing gases as well as oxides. Secondary ingot is already alloyed with natural deoxidizers such as zinc, etc., and the volatilization of the latter also tends to eliminate reducing gases mechanically.

Jan 1, 1943

By John W. Bell

In the introduction to an excellent pamphlet, John Gross&apos; makes the following statements: Although marked progress has been made along mechanical lines, the theory and conception of underlying principles have not advanced so rapidly. This lack of advance in theory may be attributed to the unfortunate situation resulting from the controversy as to whether the Rittinger or Kick law is applicable to crushing. Many pages of the technical literature are burdened with theoretical discussions in favor of one or the other of these laws, which have tended to cloud rather than to clear the atmosphere. Realizing the situation, the Milling Committee of the American Institute of Mining and Metallurgical Engineers, through its secretary, E. A. Hersam, studied the milling industry and, because of the apparently hopeless lack of agreement in the Kick versus Rittinger dispute (5, 13, 14, 0, i8, 19, 21, 22, 23. 24, 30. 34), concluded that a foundation for the theory of crushing was of primary importance. The numbers in the paragraph quoted refer to papers listed by Mr. Gross in his Bibliography on Crushing and Grinding.1 One is obliged to infer that these papers show "hopeless lack of agreement in the Kick versus Rittinger dispute." No. 22 is a paper by Arthur O. Gates2 and No. 23 is one by the writer.3 Employing the subject matter contained in papers Nos. 22 and 23 2,3 the writer will show that their authors formulated identical conclusions, based solely on experimental evidence. Exactly the same defect in the Stadler hypothesis was described in each of the two papers, although entirely different experimental methods were employed in uncovering it. Both of the authors, independently, formulated the conclusion that Rittinger&apos;s was a true hypothesis and Stadler&apos;s false. The evidence in a third paper4 will be employed to prove that Stadler&apos;s hypothesis, when examined experimentally, is worthless. STADLER&apos;S HYPOTHESIS WORTHLESS It is the writer&apos;s opinion that the evidence available in 1915 and the corroborating evidence in 1916 was amply sufficient to eliminate the need for any further consideration of Stadler&apos;s hypothesis. Certainly the evidence produced in 1918 dealt this hypothesis its coup de grace. It follows, therefore, that in the year 1918 there was only one credible hypothesis left-the Rittinger hypothesis. Gates&apos; Opinion What information is available in Mr. Gates&apos; paper?2 His conclusions are not consecutively summarized, none the less they are perfectly clear. On page 876, Gates says, and it is a very significant utterance: But my results show, among other things, that many more of Stadler&apos;s energy units are obtained per foot-pound-applied in coarse than in fine crushing. This suggests a doubt as to the correctness of his unit, since one would expect a foot-pound-applied to produce the same number of "energy units," whether the feed and resulting product were coarse or fine. When Rittinger&apos;s theory is applied, the number of mesh-tons (my unit of surface produced) is

Jan 1, 1942

By F. C. Sturges

FOR some time mining engineers have been interested in the possibility of using small diameter shafts, sunk by core drilling, as aids to ventilation and as emergency escapeways. The possibilities are interesting to contemplate, but new methods involve unknowns, and interest tends to remain passive until these unknowns are solved. Recently we have completed two 36-in. diam. core drilled shafts, and wish to make the data on these available to the industry. Both shafts were drilled for the McLain Fire Brick Co., one at its Buckeye mine and the other at its Colonial mine. Both mines are in the fireclay underlying the Lower Kittanning coal. Both mines have been in operation for a number of years [ ] and have required expensive maintenance work on return airways. It was decided that considerable savings could be effected by short-circuiting the air to the surface through small shafts. It was also realized that these holes, located near the present workings, would be of added value as emergency escapeways. Originally, 48-in. diam. shafts were considered, but actual computations showed 36-in. diam. shafts were more than ample at both mines. The shaft at the Buckeye mine is 240 ft deep, and that at the Colonial mine 258 ft deep. Both holes were started in the lower part of the Conemaugh formation and penetrated Conemaugh and Allegheny strata. The holes were started through the unconsolidated materials overlying bedrock by constructing a concrete collar with a wall thickness of 8 in. Then the shafts were drilled by the shot-core drill method. An annular groove was cut in the rock by the abrading action of chilled steel shot run under the shoe of the core barrel. The drilling was done in stages, the core barrel drilling the groove for a certain distance depending on conditions encountered, and then the cores broken off and taken out in sections. The core barrel had a 36-in. o.d. and the finished diameter of the shaft measured almost 37 in. The major questions that could not be answered until the completion of the first shaft were, (I) how much ground water would be encountered, how would it hinder the drilling, and how difficult would it be to seal off, and, (2) how would the walls of the hole stand up. The holes of course could be cased or lined, but that is considerable added expense in any shaft.

Jan 1, 1947

By Jesse O. Betterton

In the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200&apos; to 1300" I?. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accomplish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flour of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes. Essentially this process consists of circulating the lead by means of a pump in a kettle through a closed reaction cylinder, gaseous chlorine entering the reaction cylinder with the stream of lead from the pump. Molten zinc chloride is thus produced and is discharged together with

Jan 1, 1937

By C. L. Horn

All the tunneling machines discussed in this chapter are Calweld machines. I have divided the machines designed for soft-to-medium formations into three groups, correlated with typical formations and estimated compressive strengths: 1) Running sand and silt requiring blade cutters. 2) Chalk and clay, requiring drag-type cutters, for compressive strengths ranging from 0 to 2000 psi. 3) Sandstones, hard clays, and limestones, requiring disk cutters, for compressive strengths ranging from 2000 to 20,000 psi. All of the soft-to-medium-formation machines are powered by electric hydraulic or diesel hydraulic pumps. The pumps in turn drive hydraulic motors for the torque reaction. The soft-to-medium-formation machines are enclosed in a 360º shield with a cutting shoe, a center portion of the shield housing the mechanical equipment, and a tail shield. Tunnel supports are usually required, and the supports are normally erected in the tail shield. Our first machine was built in 1963, and all but five of the machines illustrated in the figures with this chapter were built in 1966 and 1967. Some of the machines manufactured will be discussed in the following sections; specific features as development has progressed will be pointed out. HARD-ROCK MACHINE The Calweld hard-rock machine has been designed along basic and accepted principles for a hard-rock mechanical borer. The features of this machine are as follows: 1) Direct electric motor drive through a planetary gear reduction ring and pinion gear, and then to the cutting head through a hollow drive shaft.

Jan 1, 1970

By Harrison Schmitt

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,&apos; Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

By Harrison Schmitt

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,&apos; Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,&apos; Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,&apos; Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

By Harrison Schmitt

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,&apos; Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

By C. M. Kleeman

All mines have a finite life and the time comes when the ore is depleted, or it has become uneconomical, or for some other reason which may be peculiar to that particular mine, it must be shut down. The operation at that point of time still has some assets such as mining and milling equipment, workshops, and in the case of a gold mine, an unknown quantity of gold which has been trapped in the treatment plant. Recovering this gold can be done at small cost and can be extremely profitable. Recovery of these hidden assets requires a good knowledge of the treatment plant, i. e. , as say values of heads, tails, and of the products produced; and if mercury for amalgamation was used, where? A careful study of available plant records can be extremely valuable in forming a working plan for adequate recovery. In the following paragraphs the various unit operations and equipment where gold can collect are described and suggestions made for its recovery. Subsequently, a case history will be given for dismantling a gold plant which had a complex flowsheet and which had been in operation for many years. Looking for trapped gold in a crushing section would invariably not be worthwhile since crushing is normally a dry process and there would be few areas where free gold could collect. In the milling section, however, many areas can literally become small gold mines in themselves. Material in the bottoms of grinding mill scoop boxes can be high-grade, and even the scale on the sides of the boxes should be scraped off and collected. Mill liners should be removed and all scale, rust, and residue collected. Residue in the bottoms of rake or spiral classifiers, if they have been used, should be removed as should the scale and rust on the sides of pump sumps, launders, etc. The following procedures should be used to extract gold from these collected materials. All steel (ball scats) should be removed, screened out, and reserved. Fine material should be placed in an amalgam barrel, water added and ground with the amalgamation tailings being sampled and assayed. If high-grade, tails should be reserved; if not, discarded. The coarse material that was screened out should be placed in a heap, regularly sprayed with water and allowed to rust. After several months this material should be screened again and the fines amalgamated.

Jan 1, 1981

IN GATHERING material for this chapter on Yerington and the one to follow on Silver Bell, the A.S.& R. project near Tucson, Arizona, I was fascinated at the way the two stories paralleled each other. For example, here are a few instances: (1) The first copper mining in the Yerington district of Nevada was in the late 1860&apos;s; the first in the Silver Bell area in 1873. (2) Each district was served by a branch railroad about 25 miles long from a main line of the Southern Pacific (by quizzical coincidence); and, in each instance, the railroad was later abandoned and torn up. (3) Each district had a sizable blast-furnace smelter ten or fifteen miles from the principal mines, and in each instance the smelter was later dismantled for junk. (4) Up to 1954, the Yerington district was credited with a production of 100,000,000 lb of copper; the Silver Bell district with 80,000,000 lb. (5) In each district the entire production had come from deposits other than the low-grade ore bodies now being exploited. (6) In each instance, existence of the low-grade deposits of the Porphyry type was recognized in the period circa1910-1914 and a substantial amount of exploratory drilling had been done, on one deposit at Yerington and on two at Silver Bell. (7) In each instance, the properties containing the Porphyry ore were acquired by a strong company (Anaconda Copper Mining Company at Yerington and American Smelt-

Jan 1, 1957

By E. B. Thornhill

Discussion of the paper of E. B. THORNHILL, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1653 to 1670. D. B. HUNTLEY, Oakland, Cal.-About 15 years ago it chanced to be my lot to cyanide some mill tailings, assaying about $5 per toll in gold and, a few cents in silver. It was in southern Idaho, a. desert region where costs are nearly as large as in central Nevada. We knew that we had a lot of tailings that had been amalgamated and contained about 1 lb. of quicksilver per ton. We knew that we would dissolve some of the quicksilver when we cyanided them with say 0.25 per cent. cyanide solution. We figured (optimistically) that the cyanide would dissolve all of the quicksilver, and we thought to capture all of that, 1 lb. per ton; and we figured out profits as partly gold, partly silver, and partly quicksilver from the recovery in working those tailings. Actually, however, we did this: We had a battery of three large, old-fashioned silver-mill retorts. We retorted our zinc-dust precipitate, recovering about ¼ lb. of quicksilver per ton treated. That was only a loss of 75 per cent. of what we originally had, but still it was profitable by virtue of the conditions. I mention it partly to call attention to the crude old way of doing it, and partly to call attention to how chemical methods for recovering quicksilver have developed in the last 15 years.

Jan 12, 1915

THE Institute of Metals Division of the American Institute of Mining and Metallurgical Engineers appointed a Research Committee in 1925 to de-termine what could be done by the Division to promote research work in the United States on non-ferrous metals. It was recognized that a considerable volume of use-ful research work in this field was being carried on by individual industrial companies as well as by the uni-versities and other research institutions, such as the Bureau of Standards. One need only refer to the recent research literature on non-ferrous metals in the TRANS-ACTIONS of the A.I.M.E., and elsewhere, to be con-vinced of healthful research activity in this field. The appointment of the Committee, however, voiced the impression that what was being done was, however excellent, inadequate for the needs of the industry. It was felt that the Division could usefully devote some of its time and effort in stimulating activity in this field. The deliberations of the Research Committee have not failed to develop wide differences of opinion even on the simple questions: (1) whether the Division can aid in any practical manner in this cause and (2) what the features of such aid might be. However, it was clear that there was only one type of research activity with which it could be very usefully concerned, viz., that on subjects of fundamental interest and general application. It was obvious that research work having special objects and more immediate commercial appli-cation should best be left to the industry itself.

Jan 1, 1927

By J. A. Berger, G. W. Wiener

Several transition metal nitrides have been prepared and their saturation magnetization determined. On the basis of an atomic model of ferromagnetism involving a consideration of nearest neighbor interactions and the assumption that all atomic moments of the metal point in the same direction, it appears that the nitrogen interacts with d-shell of the transition metal in such a way as to reduce the magnetic moment. THERE is a large class of materials having metallic properties which are formed by a combination of hydrogen, boron, carbon, oxygen, or nitrogen with the transition metals. Several attempts have been made to establish the type of metal-nonmetal bonding in these interstitial alloys because it is believed that many of the physical properties of these materials are determined by the characteristics of this bond. Several of these alloys are ferromagnetic, and thus a powerful method is available for investigating the structures in a direct manner by measuring the saturation magnetization. The latter is a fundamental property of ferromagnetic metals and alloys which depends primarily on the electron distribution surrounding the atom. For the first row of transition metals, this refers specifically to the 3 d-shell. Since bonding involves the electronic configuration between atoms, there is reason to suppose that a relationship exists between ferromagnetism and bond type. In the case of the interstitial structures studied in this work, bonding will refer to the distribution of electrons between the transition metal and the nonmetal. Since these alloys have metallic properties, it is further proposed that any bonding interactions will involve the outer p-shell of the interstitial element and the incomplete d-shell of the transition metal. If this is the case, then the relationship between ferromagnetism and metal-non-metal bonding is established qualitatively. In order to investigate the subject quantitatively, certain transition metal nitrides were chosen because they have simple crystal structures, are ordered alloys, and are ferromagnetic. They also have sufficiently high saturation magnetization to be of technical interest. Currently there are two major theories of ferromagnetism, each of which has been applied to the interpretation of the saturation magnetization in terms of atomic structure. They are usually referred to as the band theory and the atomic theory. The former has found widespread application to the study of pure metals and certain solid-solution allays. However, it has not been applied to the interstitial structures or ordered alloys because it does not interpret the properties directly in terms of the crystal structure. The atomic theory on the other hand is especially suited to the study of interstitial structures because it permits an interpretation of ferromagnetic phenomena in terms of the crystal geometry. As has been pointed out previously, the nitrides have simple ordered crystal structures and, therefore, the choice of the atomic theory for the interpretation of the data is a natural one. One of the prime difficulties with the atomistic theory is that its mathematical justification is much more difficult, and for this reason its general acceptance will depend to a large extent on the value it has in explaining and predicting the results of experiment. Before the presentation of the theoretical basis for understanding the metal-nonmetal bond, it is useful to review the ideas existing prior to this work. Four different interpretations have been given to the metal-nonmetal bond. These are summarized as follows: 1—acceptance of electrons by the nonmetal from the incomplete d-shell of the transition metal, 2—transfer of electrons from the nonmetal to the incomplete shell of the transition metal, 3—no exchange of electrons between the two atoms, and 4— a resonating type of bond involving the p electrons of the interstitial atom giving rise to half bonds. Zener&apos;-4 in a recent series of papers has proposed a new theory of ferromagnetism and has developed an explanation of the observed saturation magnetization of iron nitride (Fe,N) using the concept that nitrogen accepts electrons from the 3d-shell of iron. Jack," on the basis of atom size considerations in iron carbonitrides, has proposed that nitrogen transfers or donates electrons to the inner 3d-shell. He found that the effective size of the carbon atom was less than that of nitrogen and thus suggested that the interstitial atoms give up electrons. Kiessling" has studied the borides of several transition metal atoms and proposed that boron loses one p electron to the transition metal. He postulated that the additional electron added to the metal lattice compensates for the loss in metallic properties which results from the increased metal-metal atom separation. GuillaudT3" has proposed similar arguments from some recent magnetic studies he had made on manganese nitride. However, he did not base his conclusions on a quantitative argument. Pauling," in a recent paper, discussed electron transfer in in-termetallic compounds. He classified nitrogen as a hyperelectronic atom which can increase its valence by giving up electrons. He classified the transition metals as buffer atoms which are capable of either accepting or giving UP an electron. He pointed out that two factors are operating which promote electron transfer because they lead to increased stability. The first is an increase in the number of bonds, and the second is a decrease in the electric charges on the atoms. These ideas when applied to the interstitial nitrides would indicate a viewpoint favoring electron transfer by nitrogen to the transition metal. Hagg7s arguments in favor of no exchange are adequately summarized by Wells." Implicitly, Hagg

Jan 1, 1956

By A. H. Cottrel

SINCE metallurgy exists to provide strong, tough, engineering materials it must inevitably be perpetually concerned with the problem of brittle-ness. The steel-making industry was created because chemically unrefined iron is brittle. The steel-working and alloy-steel industries exist partly because hardness and ductility are mutually exclusive qualities in structurally unrefined steel. Yet, in spite of these immense industries, the brittle failure of steel ships hulls, bridges, pressure vessels, and pipelines, is still a contemporary problem. In fact, brittleness is a normal property of most solids, including metals and alloys, at low temperatures. Only face-centred cubic metals are commonly ductile at the lowest temperatures, and even here exceptions are known.&apos;," Expensive are-melting processes. under inert gases or vacuum, have been developed to overcome brittleness in titanium, zirconium, columbium. and molybdenum. Polycrystal-line zinc, magnesium, and uranium have little ductility at room temperature. Beryllium, chromium, and tungsten have even less; similarly for antimony, bismuth, germanium, silicon, intermetallic compounds, and metallic carbides, nitrides, silicides, and borides. Oxides and other ceramics would be ideal creep-resistant materials but for their extreme brittleness when cold, and great efforts have been made to overcome this problem by mixing ceramics with metals. In fact, the traditional use of the name metallurgy for what is really the science of engineering materials is a recognition that most non-metallic solids have so far been precluded, by their extreme brittleness, from use as major structural materials in mechanical engineering. Most of what we know about brittleness in metals has come from studies of structural steel, and it is this material that shall mainly be considered. The things we have learned from it have a wider application, at least to other body-centred cubic transition metals, although the extent to which similar ideas can be applied to hexagonal metals and other materials is not yet clear. Fracture and Plastic Deformation The theoretical breaking strength of an ideal solid, about E/10 where E is Young&apos;s modulus, has been approached reasonably closely in experiments on fibres. But large specimens break at much lower stresses. For example, brittle cracks in large structural steel assemblies have been observed to spread catastrophically at speeds of 6000 ft per sec under stresses of about 10,000 psi, i.e. about E/3000. There are two sources of weakness; stress concentrations, and chemical agents in grain boundaries or on crack faces that lower the surface energy y of the material. Although we shall deal mainly only with the first of these, much of the discussion is also applicable to the second when different values of y are used. Griffith&apos;s well-known formula p = [ 2Ey/p(1 - v2)c]1/2 [1] gives the smallest tensile stress p able to propagate an atomically sharp surface crack of length c or interior crack of length 2c through a thick plate (compared with c) of elastically isotropic material of

Jan 1, 1959

By Gerald Edmunds

Castings of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, sometimes nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals .primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is developed to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and therefore the position of the grains is more cornplex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicating that thermal contact was better there than in neighboring areas. The nucleus from which a columnar grain grows may be so oriented that its direction of maximum growth rate does not coincide with the direction of the thermal gradient. In this case the long axis of the grain probably assumes an intermediate position. Notwithstanding these minor irregularities, the situation does exist that the long axes of the columnar grains are generally disposed approximately perpendicular to the mold surface. Schmid and Wassermanl and Nix and Schmid2 have determined the orientation texture of columnar grains in castings of several cubic, tetragonal, hexagonal close-packed and rhombohedra1 metals. For zinc and cadmium, they report the basal plane to be parallel to the columnar grain axes, with no preference for any particular direction in this plane to coincide with the grain axes. This texture, termed a ring fiber texture,3 is uncommon in metals; zinc and cadmium are the only ones reported to exhibit it. Generally, it is stated, a simpler texture exists in which a principal, though not necessarily the most closely packed, crystallographic direction is parallel to the direction of heat flow. In cast magnesium (also hexagonal close packed) they report a digonal axis I, [100] direction, parallel to the direction of heat flow. The writer is not aware of any other orientation-texture determinations on cast polycrystalline hexagonal metals. In view of the observations reported in the present paper it is of interest also to note that Nix and Schmid stated that a

Jan 1, 1941

By Gerald Edmunds

Castings of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, sometimes nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals .primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is developed to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and therefore the position of the grains is more cornplex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicating that thermal contact was better there than in neighboring areas. The nucleus from which a columnar grain grows may be so oriented that its direction of maximum growth rate does not coincide with the direction of the thermal gradient. In this case the long axis of the grain probably assumes an intermediate position. Notwithstanding these minor irregularities, the situation does exist that the long axes of the columnar grains are generally disposed approximately perpendicular to the mold surface. Schmid and Wassermanl and Nix and Schmid2 have determined the orientation texture of columnar grains in castings of several cubic, tetragonal, hexagonal close-packed and rhombohedra1 metals. For zinc and cadmium, they report the basal plane to be parallel to the columnar grain axes, with no preference for any particular direction in this plane to coincide with the grain axes. This texture, termed a ring fiber texture,3 is uncommon in metals; zinc and cadmium are the only ones reported to exhibit it. Generally, it is stated, a simpler texture exists in which a principal, though not necessarily the most closely packed, crystallographic direction is parallel to the direction of heat flow. In cast magnesium (also hexagonal close packed) they report a digonal axis I, [100] direction, parallel to the direction of heat flow. The writer is not aware of any other orientation-texture determinations on cast polycrystalline hexagonal metals. In view of the observations reported in the present paper it is of interest also to note that Nix and Schmid stated that a

Jan 1, 1941