Search Documents

By W. W. Yankie, A. T. Chatas

This paper is written as a discussion of the paper, "Buckling of Tubing in Pumping Wells, Its Effects and Means for Controlling It" by Arthur Lubinski and K. A. Blenkarn, which war published in the March, 1957, issue of Journal oP Petroleum Technology. An analogy is drawn between the buckling of tubing in pumping wells and a fiube, fitted with frictionless pistom, linked by an inelastic rod, and which is subject to an internal pressure. A simple derivation shows that the critical internal pressure exerts a hydrostatic force on the pisfon which is close to the Euler load for compression buckling of the same tube. While the results agree with those of Ref. I, the basis of calculations has been changed and clarified. The presence of internal upsets at the pistons is discussed. INTRODUCTION In the Appendix, Lubinski and Blenkarn state that a tube with ends closed by frietionless pistons connected by an inelastic rod (Fig. 1) will behave as a column loaded with a force equal to the tension force in the rod. They note that, while the fluid may not resist a shear force, the moment in every cross section is piston force multiplied by the elastic line deflection (c.f., the loaded column). Since the equations of the elastic lines are similar in the two cases, the solution is carried over from the loaded column. On the contrary it is suggested that while the method of solution remains unchanged from the column case, the actual stress distribution is different, a fact which is taken into account in this note. A simple method of approximating the buckling pressure is given, and their reasoning in our mathematical language is continued. GENERAL EQUATIONS The equation of an elastic line, initially straight in the x direction (Fig. 2), is given by In the case of a loaded column, this may be written: For the pressurized tube it was shown, by analogy with the loaded column, that tion has a solution that, for P, = EI/P, any deflection is stable (a criterion for buckling). An attempt will be made to describe more precisely, the forces acting on the tube, and to analyze the buckling condi,tions. DISCUSSION If the tube assumed a deflected position, the volume between the pistons would increase so that in deflecting, the energy of the fluid would decrease. When the increase in elastic energy of the tube (due to bending) is equal to the decrease of fluid pressure energy, buckling conditions exist. Analyzing the forces on the tube (Fig. 3), two transverse forces, T,, T,, exerted by the pistons, are balanced by a resultant of the pressure elements which are linearly dependent on the local curvature of the elastic line (Fig. 4). Unlike most buckling cases, the forces depend on the shape of the elastic line, a condition that makes a rigorous mathematical treatment difficult. Several approximations may be used to clarify the problem.

By H. R. Hendricks

THE ore of the Iron King Mine, being very hard and having a very fine crystalline structure, presents many problems in milling that are not present in ordinary lead-zinc ores. This very fine crystallization causes much interlocking of minerals and is most prevalent between the gold and pyrite and the sphalerite and pyrite. The recovery of gold is extremely important in the economic value of the ore and therefore constitutes a large part of the metallurgical problem to be solved. All of the gold is free but it has not been observed in any of the mill products except under very high magnification. Some of the gold is tarnished, and this condition also makes recovery difficult. The gold values have been determined to be highest in association with chalchopyrite and arsenopyrite. The silver occurs mostly in association with galena and tennantite. A small amount of native silver has also been observed occasionally. The galena, being softer than the other minerals, frees much better in grinding. Some oxidation of galena is present in the ore, as the nonsulphide lead content amounts to approximately 10 pct of the total lead. Some oxidation of sphalerite is also present in the ore. Microscopic examination of the zinc concentrate shows many grains in the minus 325-mesh to be half pyrite, together with the fact that some of the zinc is marmatite, makes production of a high-grade zinc concentrate very difficult unless recovery is sacrificed. In the grinding, it has been determined that the flotation feed must be maintained at 85 pct minus 200-mesh to free the minerals sufficiently to make the best economic recoveries. Table I illustrates the effect of fine grinding. It shows that the bulk of the recovered minerals is in the minus 325-mesh size and is the part of the minerals that is more readily freed. The pyrite concentrate is not given in the table because it contains practically no minus 325-mesh. DEVELOPMENT OF PRESENT FLOWSHEET AND MILLING PRACTICE The first milling operation started in 1938, with a mill capacity of 140 tons daily, producing a bulk gold-silver-lead concentrate. After several stages of expansion and changes of the mill flowsheet, the mill is currently treating 380 tons of ore daily and three separate concentrates are produced. In order of their importance and value, these are: (1) lead concentrate, (2) zinc concentrate and (3) pyrite concentrate. The present average grade of mill heads is: gold 0.11 oz, silver 4.00 oz, lead 2.50 pct, zinc 7.60 pct, copper 0.22 pct, iron 22 pet and 30 pct insolubles. Specific gravity of the ore is 3.8. During the period when bulk flotation was practiced, the flowsheet was very simple. The ore was ground fine enough to liberate as much gold, silver and lead as possible. Necessary collectors and frothers were added in sufficient quantity

Jan 1, 1947

By A. W. Bitner, A. W. Asman

An analysis is made of three different types of section production units that represent the manner in which most of the nation's bituminous coal is produced. The general delays and production characteristics of these sections are presented along with a method for evaluating section performance based on actual and theoretical production characteristics. THE forerunner of the modern mechanical loading machine first entered the mines in 1890—a Stanley header with a conveyor. Since then progress has been substantial, both in the design and application of mechanized production units. Mechanization is almost a necessity for survival in the economy of today. In this paper an analysis is made of three types of sections, and a method for evaluating section performance based on present production characteristics and theoretical characteristics is presented. In mechanical loading mining sections the loading machine is the unit directly responsible for production. If the face preparation units provide a plentiful supply of properly prepared coal and the transportation system is coordinated and adequate, the loader will be idle a minimum of time. If either of the above do not perform adequately or other delays occur, the effect on production will be reflected in the performance of the loading machine. Therefore, attention is focused on the loading machine and factors that affect the overall performance of the production unit. Three complete mechanized production units are presented for analysis: A track section, a trackless section using battery-powered shuttle cars, and a trackless section using cable-reel shuttle cars. These particular sections were chosen for the following reasons: 1—The daily tonnage and mining conditions are approximately the same. 2— Production in each is 10 to 20 pct above the daily average. 3—The production characteristics and delays are average and typical. 4—They represent the manner in which the most of the nation's bituminous coal is produced. A. W. ASMAN, and A. W. BITNER, Members AIME, are Chief, and Research Assistant, respectively, Div. of Mining, The Pennsylvania State College, State College, Pa. Discussion on this paper, TP 3140F, may be sent to AIME by Oct. 31, 1951. Manuscript, Feb. 22, 1951. St. Louis Meeting, February 1951. Section A Fig. 1 is a layout for the track mining section showing the development to date, the projected plan and the cuts loaded on the shift studied. The seam mined averages 96 in. in thickness with a fireclay bottom and a roof of 10 in. of drawslate topped by sandstone. The mineability is considered good, and roof support is not a difficult problem. Two locomotives are used in the section to minimize the losses occurred in trip changing. The places are driven 20 ft wide, and the crosscuts are angled to permit fast tramming of the equipment. Table I lists the equipment and labor that make up the section. ANALYSIS Production Characteristics: The average loading rate for eight loading machines studied of this type is 1.81 tons per min. This one at 2.78 is considerably above average.

Jan 1, 1952

By G. H. Anderson

Cadmium-coppeR precipitate, a byproduct of the purification stage of the zinc plant, is composed mainly of zinc, cadmium and copper in varying amounts depending on the efficiency of precipitation and the cadmium and copper contents of the impure solution treated. The composition range is approximately: cadmium 10-12 pct, copper 6-8 pct, and zinc 3&35 pct. As received at the cadmium plant, the precipitate is a dark gray to black press cake produced by filter pressing the flocculent cadmium-copper precipitate formed when impure zinc solution is agitated with zinc dust. The details of the cadmium-copper precipitation are to be found in the paper "Electrolytic Zinc at Risdon, Tasmania," by W. C. Snow. Transactions AIME, 121, 501. The treatment, in addition to recovering cadmium as metal, yields a copper product as a residue for realization and recovers in solution for return to the zinc plant, the excess of zinc dust used during purification. The recovery of cadmium metal is approximately 200 tons† per year, but, with the amount of copper residue recovered, varies with the zinc production tonnage, composition of the original concentrates, degree of roasting and other operational factors. The operations involved in the recovery of the foregoing materials are carried out in a building adjacent to the purification section of the zinc plant and can best be described by dividing the process into the following stages: 1. Oxidation and Grinding of the cadmium-copper precipitate. 2. Leaching and Filtering. 3. Precipitation of cadmium. 4. Oxidation and Grinding of the precipitated cadmium. 5. Leaching oxidized cadmium precipitate and Purification of leach solution. 6. Electrolysis. 7. Melting, Casting and Packing. A feature of the process is the use of two distinct solution circuits. Spent electrolyte from the zinc plant circuit containing about 10 pct sulphuric acid is used as the primary solvent of the cadmium and zinc present in the oxidized precipitate. When the cadmium is later separated by precipitation and filtering, the filtrate, originally zinc plant spent electrolyte and now fortified in zinc, is returned to the zinc plant. The precipitated cadmium, after oxidation, is redissolved in spent electrolyte from cadmium electrolysis which solution is in closed circuit within the cadmium plant except for discards to the zinc plant circuit as mentioned in Section 5 hereinafter. (Fig 1.) Details of the various operations follow. I. Oxidation and Grinding of the Cadminm-copper Precipitate The precipitate having had a preliminary drying by compressed air in Dehne filter presses in the zinc plant is trucked to a storage platform of sufiicient length to store 3 to 4 days' production separately. After 48 hr exposure to atmosphere, oxidation is sufficient to enable all cadmium and zinc but only a portion of the copper to be dissolved in dilute sulphuric acid. The oxidized precipitate is shovelled into trucks and, after weighing and sampling, is broken in size by means of

Jan 1, 1950

By L. T. Larson, M. L. Picklesimer

The relationship between the apparent angle of rotation of monochromatic plane polarized light and the tilt of the basal pole from the surface normal has been experimentally determined for zirconium over the wavelength range of 500 to 655 mp. This relationship allows the determination of the spatial orientation of the basal pole of an individual grain in a polycvystal-ling zivrconium specimen to within ±3 deg by three simple tneasurements with a polarized-light metallurgical microscope. The method of measurement is discussed in detail. THE optical anisotropy of materials having noncubic crystal structures has long been used to reveal features by polarized-light microscopy. Petrographers have used measurements of certain optical properties to identify and classify transparent or translucent minerals. More recent work (i.e., Cameron1) has extended such measurements to opaque minerals in reflected light. Few attempts have been made to make similar measurements on noncubic metals. Couling and pearsall2 have reported that a sensitive tint plate can be used in a polarized-light metallurgical microscope to determine the position of the basal-plane trace in a grain of polycrystalline magnesium. Reed-Hill3 has reported that the same technique can be used for zirconium. We have found that the precision of measurement can be increased to about ±0.5 deg by using a Nakamura plate4,5 to determine the exact extinction position after the sensitive tint plate has been used to locate approximately the basal-plane trace. This report describes a method for measurement of another optical property, the apparent angle of rotation. This measurement permits determination of the angle between the basal pole of a grain of a hcp metal and the normal to the surface of the specimen. When the two measurements are combined, the orientation of the basal pole in space can be determined from three simple measurements on a single surface. One to two hundred such determinations will permit plotting of a basal-pole figure for the polycrystalline material with reasonable accuracy. When normally incident, monochromatic, plane-polarized light is reflected from the surface of an optically anisotropic material, the light may be converted to elliptically polarized light, the plane of vibration may be rotated, or both may occur. The el- lipticity, the angle of rotation, and the reflectivity can be related to the indices of refraction and the absorption coefficients of the material.6,7 Ellipticity values can be determined with an elliptical compensator, but not with the ease and precision desirable for the present purposes. Measurement of the angle of rotation requires only the determination of the angle from the crossed position (90 deg to the polarizer) that the analyzer must be rotated to obtain extinction when the trace of the optical axis in the surface is at 45 deg to the vibration direction of the polarizer. The angle of rotation of the analyzer is approximately 6/5 that of the true angle of rotation of the light as reflected from the specimen because there is a small amount of additional rotation produced during the passage of the reflected light through the mirror of the microscope. Since we are presently interested only in determining the tilt of the basal pole, the angle of rotation of the analyzer (the apparent angle of rotation of the light, i.e., uncorrected) can be used. Precision of the measurement can be increased substantially by the use of a Nakamura plate4,5 in determining the extinction position. In an optically uniaxial material (hcp or tetragonal crystal structure) the angle of rotation depends only on the optical properties of the material and the orientation of the optical axis of the grain relative to the plane of incidence of the plane-polarized light.7,8 Thus, in a metal such as zirconium, the apparent angle of rotation at the 45-deg position in any given wavelength of light is a direct measure of the tilt of the basal pole from the normal to the surface. If the optical properties vary with wavelength, the apparent angle of rotation for any given tilt of the basal pole will vary. None of the required information exists in the literature for zirconium nor for any other non-cubic metal. MEASUREMENTS ON SINGLE-CRYSTAL ZIRCONIUM A single-crystal sphere of zirconium 9/16 in. in diam was spark-cut from a single-crystal rod grown from iodide bar by an electron-beam zone-melting process.9 The damaged surface was removed by chemical polishing in a 45/45/10 mixture (by vol) of water, concentrated HNO3, and HF (48 pct) and then electropolishing at 50 v in a bath1' of methyl alcohol and perchloric acid (95/5 by vol) at -70-C. The single-crystal sphere was mounted in a five-axis goniometer stage having a removable eucentric X-ray diffraction goniometer head for the two inner orientation axes. The basal pole of the single-crysta sphere was aligned parallel to a third axis of the goniometer stage by using the sensitive tint method to determine the basal-plane trace at several rotational positions of the sphere. The alignment was then checked by removing the sphere and eucentric gonio-

Jan 1, 1967

By M. J. Hordon

Measurements of the 103 yield stress of ordered and disordered poly crystalline Cu ,Au were related to the ordered antiphase domain size determined by resistivity measurements. For undeformed material, a yield stress maximum wa obtained at a critical domain diameter of about 40A. Plastic deformation resulted in a marked increase in the yield stress and electrical resistivity of the ordered alloy compared to the disordered, the strain hardening rate increasing regularly with initial antiphase domain size. Order hardening was accompanied by a sharp reduction in size of the initially large domains. It has been observed that the yield stress of ordered and partially ordered Cu3Au alloy varies sensitively with antiphase domain size aid degree of order.ly2 In addition, ordering of the lattice leads to a marked increase in the strain hardening rate (order hardening) as compared to the rate for the disordered alloy. In the present investigation, changes in the electrical resistivity and yield stress of ordered polycrystalline Cudu with varying initial domain diameters were measured after tensile plastic deformation in order to examine the effect of cold work on the antiphase domain size. EXPERIMENTAL PROCEDURE Au-Cu alloy of 99.99 pct purity analyzing 50.85 wt pct Au-balance copper was obtained from the Handy-Harmon Co., N. Y., in the form of 0.061 in. diam drawn wire. Wire specimens 3 in. in length were given the following annealing treatment in nitrogen: 500" for 72 hr, 820" for 15 hr, and 450" for 5 hr, followed by a water quench. The annealing sequence resulted in a completely disordered structure with a grain size of about 0.2 mm. The disordered specimens were then reannealed at 360' in nitrogen for periods varying from 10 min to 150 hr followed by quenching to produce ordered structures with varying domain sizes. The degree of ordering and variation of domain size was followed by electrical resistivity measurements made at room temperature using a low resistance precision Kelvin double bridge apparatus. The specimen resistance was determined over a length of 4.0 cm between two brass knife-edge contacts while the specimen was immersed in an oil bath to minimize temperature variations. In addition, the current flow in the circuit was minimized by a current pulse technique in balancing the bridge in order to avoid heating the specimen. Using a sensitive galvanometer to detect the bridge null, the accuracy of the resistance measurement Wire specimens were plastically strained in tension with an Instron tensile unit at strain rates in the range 5 x 10"5 sec-' to 2 x 10"4 sec-'. Stress and extension data were fed into the Instron chart drive amplifier to obtain the actual stress-elongation curve from which the yield stress at 10"3 strain was determined. The maximum resolution of the apparatus was approximately 50 psi stress and 3 x 104 strain. At various plastic strain levels, deformation was interrupted and the electrical resistivity determined after removing the stress. RESULTS AND DISCUSSION 1) Yield Strength of Ordered Cudu. In order to determine the effect of the ordered antiphase domains on the initial yield stress, specimens were prepared with varying domain sizes ranging from zero for 5 completely disordered structure to about lo5A for a completely ordered structure by suitable annealing treatment. Domain sizes were estimated by comparing room temperature electrical resistivity data with the original data of Jones and sykes3 as modified by rdle.' In agreement with previous work, the resistivity varied sensitively with domain diameter and degree of order, decreasing from approximately 11.6 x l0- ohm-cm for the disordered structure to about 5.9 x l0- ohm-cm for ordered domains above 10"3 cm in diameter. Fig. 1 shows the change of the 103 yield stress with ordered domain size. It is evident that the maximum

Jan 1, 1963

By B. F. Oliver, F. Garofalo

Gas-metal heterogeneous reactions and zone-lrelting were sinultarneously employed to produce several high-purity irons with low interstitial contents in a levitating- zone melter. Successive zone-tneltitzg pusses were made in carious sequences of atmospheves which included prepuvified tank hy-drogeta, water vapor hydrogen, palladiuril-purified hydrogen, and vacuunm of 2 x 10-6 Torr. Different irons ranging in purity from 99.89 to 99.996 pct with residual curbon contents of 17, 8 to 10, and 3 to 5 ppm have been Drepared. No measuvable gradient in the residual carbon content was observed along the entire zone-melted length (6-10 in.) in I-ilz.-diameter bars. The absence of a carbon-concentration gradient in the solid indicates an apparent distvihution coefficient of 1, an unusual condition. Internal friction, solid-state extraction, and hot-hardness results indicate that the level of mobile carbon in a iron depends on the gas-metal heterogeneous reactions employed. Purification under an oxidizing atmosphere resulted in the immobilization of nearly all of the carbon present at leuels of 10 ppm or less. Continuation of purification in a reducing atmosphere veturued the carbon to a state of mobility which was aguin reversed by further purification in all oxidizing atmosphere. The immobilization of curbon at "vesidual levels " is believed to be associated with a strong interaction between carbon and oxygen atoms. frons with low carbon and nitrogen contetzts which did not exhibit a hot-hardness peak were produced after zone ynelting in vacuum. CARBON, nitrogen, and oxygen have strong and well-known effects on many properties of iron. These effects persist even at concentrations of 5 to 20 ppm. The intent of the present investigation was to establish procedures for the preparation of high-purity iron with concentrations of these elements in the range of 5 to 20 ppm and lower. The results reported here deal with the procedures employed to prepare high-purity iron, and with observations on the behavior of certain elements at "residual levels": particularly carbon. The details of the (levitating) zone melter in which the final purification steps are performed and the necessary control of the pertinent solidification variables have been described previously.1,2 MATERIALS AND PROCEDURES Commercial electrolytic iron was induction vacuum-melted and cast into 30-lb ingots. Melt additions and ingot analyses for carbon, oxygen, and nitrogen are noted in Table I. All ingots were melted in stabilized zirconia crucibles conditioned with one iron wash heat. Middle sections of the ingots were forged to 1-1/4-in. rounds, machined to 1-in.-diameter bars, then cut to 36-in. lengths. The zone-melting operations were performed on six iron bars (A to F) at a freezing velocity of 2 in. per hr with the freezing interface rotating2 at 200, 300, or 400 rpm. Liquid zones were passed through the bars in various sequences of atmospheres, Table 11, including prepurified tank H2, palladium-purified Hz, wet H2, and system vacuum of 2 x 1018 Torr. Wet-Hz atmospheres were obtained by bubbling palladium-purified Hz through water exhibiting a resistance of 3 megohms. This water was heated with a platinum-immersion heater and was degassed prior to use. Zone melting in a wet-HZ atmosphere resulted in oxidation of the elements which are oxi-dizable with respect to iron. Fine oxide particles were observed on the surface of the liquid zone, and were encased in the bar surface with the passage of the molten zone. Between each zone pass, the surface of the bar was removed by filing and deep etching; this was continued until the oxide formation ceased. The filings were magnetically separated and the residues analyzed by optical spectroscopy. These were especially high in silicon and manganese. Samples were removed from the iron bars, with few exceptions, following each zone-melting operation. A 0.08-in.-thick disc was cut with an Al2O3 cut-off wheel at a point 1/2 in. above the beginning of freezing. Material from each disc was used for hot-hardness measurements, resistivity-ratio measurements, and carbon, nitrogen, and oxygen analyses. Analyses for most other elements were

Jan 1, 1965

By F. I. Grace, L. E. Murr

The mechanical responses and residual defect structures in 70/30 brass and type 304 stainless steel following explosive shock loading and cold reduction by rolling have been studied. A distinct relationship was observed to exist between the residual mechanical properties and micro structures observed by transmission electron microscopy. Shock-loaded brass deformed primarily by the formation of coplanar arrays of dislocations and stacking faults at lower pressures, and twin-faults (deformation twins and €-martensite bundles) at higher pressures (> 200 kbar). The micro -structures of cold-rolled brass were characterized by dense dislocation fields elongated in the rolling direction. Stainless steel was observed to deform by the formation of dense arrays of stacking faults at lower shock pressures and twin-faults at high shock pressures (>200 kbar). Lightly cold-rolled stainless steel deformed similar to low Pressure shock-loaded stainless steel, but transformed to a' martensite in heavily cold-rolled stainless steel. Discontinuous yielding was observed for the heavily cold-rolled stainless steel, and stress reluxution in the weyield region for cold-rolled and shock -loaded stainless steel was interpreted as an indication of the ability of twin-faults and stacking faults to act as effective barriers to dislocation motion. A simple model for the formation of the planar defects and a' martetnsite is presented based on the propagating of Shochley partial and half-partial dislocations. A considerable effort has been expended over the past decade in an attempt to elucidate the response of metallic-crystalline solids to the passage of a high velocity shock wave (e.g., smith,' Dieter,2 and zukas3). While it has been possible to obtain relevant information pertaining to the residual defect structures and mechanical properties, there have been few rigorous attempts to draw a direct comparison between these structures and properties. In addition, numerous investigators have recently observed the occurrence of deformation twinning in shock deformed fcc metals (e.g., Nolder and Thomas,4 and Johari and Thomas5), but little attempt has been made to elucidate the mechanisms of formation of these defects. Comparative data for metals deformed by shock-loading and the same metals deformed by more conventional modes of deformation such as cold-reduction by rolling is also generally lacking. The present investigation therefore has the following objectives: 1) to examine the mechanical properties of some explosively shock loaded and cold-rolled fcc metals of low stacking-fault energy as a function of their residual substructures; 2) to present a simple model for the formation twin-faults and related defect structures in the low stack-ing-fault energy materials of interest (70/30 brass, ySFg= 14 ergs per sq cm; and 304 stainless steel, ySF = 21 ergs per sq cm); 3) to make some deductions with regard to the residual characteristics of dislocation and planar defect substructures in cold rolled and shock loaded 70/30 brass and type 304 stainless steel. In particular, it was desirable to characterize the residual hardening effects of particular deformation substructures. I) EXPERIMENTAL PROCEDURE Sheet samples of 70/30 brass (0.005 and 0.15 in. thick; annealed at 659°C for 2 hr) and type 304 stainless steel (0.007 in. thick; annealed 0.25 hr at 1060°C) of nominal compositions shown in Table I were cold-rolled in one direction only to produce reductions in thickness of 15, 30, 45, 60, and 75 pct in the brass; and 5, 15, 25, 35, and 45 pct in the stainless steel. Identical sheet samples in the annealed (unrolled) state were subjected to plane compressive shock waves to various peak pressures ranging from 0 to 400 kbar in the brass and 0 to 425 kbar in the stainless steel; and with a constant peak pressure duration of approximately 2 microseconds. A detailed description of the shock loading technique has been given previously.6 Tensile specimens 1.0 in. in length and 0.125 in. in width were cut from the cold-rolled sheets (tensile axis parallel to the rolling direction), and the shock-loaded sheet specimens. Stress (load)-strain (elongation) measurements on the tensile specimens were made on a Tinius-Olsen load-compensating tensile tester using a strain rate of 2.7 x 10-3 sec-1. Tensile tests were repeated at least twice, giving essentially the same results. Stress relaxation measurements in the preyield region were also made using an initial strain rate of 5.4 x 10-4 sec-1. In addition to tensile and stress relaxation measurements, Vickers microhardness measurements were made on all samples. A total of 100 microhard-ness readings were obtained for each specimen following a light electropolish to ensure uniform surface conditions for all tests. The hardness averages ob-

Jan 1, 1970

By G. R. Leverant, C. P. Sullivan

To evaluate the effect of a dispersion of nondeform-able, incoherent, second-phase particles on high-strain cyclic deformation and fracture, recrystallized TD-nickel (Ni-2ThO2) and a commercially pure nickel, Ni-200, were fatigued under strain control at total strain ranges varying from 0.009 to 0.036. Relative to the Ni-200, the slip at the surface of the TD-nickel was more wavy and discontinuous due to the presence of the thoria particles. This made crevice formation (incipient cracking) within slip bands more difficult in TD-nickel than in Ni-200. Both materials cyclically hardened to a constant (saturation) flow stress which increased with increasing plastic strain amplitude. Cellular substructures were developed in both materials during cycling. The cell size in TD-nickel was controlled by the thoria particle distribution and was independent of plastic strain amplitude over the range investigated. The cell size in Ni-ZOO was larger than that in TD-nickel at similar plastic strain amplitudes and was a function of plastic strain amplitude. These results, together with the cyclic stress-strain curves for both materials, are discussed in terms of a model for fatigue strain accommodation at saturation recently proposed by Feltner and Laird. NUMEROUS fatigue investigations have considered the interrelation of slip character, dislocation substructure, and cracking in pure metals and solid-solution alloys. However, except for the studies of the low-strain fatigue of internally oxidized copper alloys1 and cast, dispersion-strengthened lead,&apos; little is known about the effects which small, incoherent, nondeform-able, second-phase particles have on cyclic deformation and cracking processes. Effects due to the particles alone are often obscured by a dislocation substructure introduced during thermomechanical processing of dispersion-strengthened metals. In the present study, recrystallized TD-nickel and a commercially pure nickel, Ni-200, were employed to evaluate the effect of a thoria dispersion on high-strai fatigue deformation and cracking at room temperature. I) MATERIAL AND EXPERIMENTAL PROCEDURE The TD-nickel was supplied by DuPont as a 5/8-in.-thick stress-relieved plate which had been subjected to a proprietary schedule of thermomechanical treatments, and the Ni-200 as 3/4-in. bar which was subsequently annealed for 2 hr at 850°C in argon resulting in an average grain diameter of 0.05 mm. The compositions of these materials are given in Table I. The microstructure of the TD-nickel consisted of elongated grains parallel to the primary working direction with an average width of 0.16 mm, Fig. l(a). Many fine annealing twins were present indicating that the starting material was in a recrystallized condition; this supposition was confirmed by the absence of of any extensive dislocation substructure, Fig. l(b). Sheetlike stringers parallel to the rolling direction were occasionally seen both within grains and at grain boundaries. Some approximately spherical particles about 2 in diam, which may correspond to exceptionally large thoria particle aggregates, were also present. The average Young&apos;s modulus of the plate material in the rolling direction was 21.8 X 106 psi which is consistent with a {100}<001>recrystalliza-tion texture3&apos;* being prominent. In transmission microscopy, the 2.3 vol pct of thoria particles generally appeared to be uniformly distributed although some clusters, 0.1 to 0.3 in diam, of larger particles were observed as previously reported for TD-nickel sheet,5 and stringering of particles was present in some areas as welt. The average diameter of the thoria particles was 450A with a calculated mean planar center-to-center spacing of 2100A, as determined by quantitative metallographic analysis.= The 0.2 pct offset yield stress was 36,000 psi which agrees with the value predicted by the modified Orowan relation7 for edge dislocations bowing between thoria particles of the size and spacing observed in the present investigation. Fig. 2 illustrates the specimen design employed for the axial high-strain fatigue testing. Adapters were screwed onto the threaded portions of each specimen so that testing could be performed in the same manner as that reported for buttonhead specimens.8 Stressing was coincident with the working direction for both materials. The gage section of each specimen was electropolished and lightly etched prior to testing. The total strain was controlled, being varied between zero and a maximum tensile strain ranging from 0.009 to 0.036. In addition to these tests, a circum-ferentially notched TD-nickel specimen was cycled over a total strain range of 0.0075. The same strain

Jan 1, 1969

By R. G. Patterson

The usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired sue and shape, and in one method1 a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averag- ing a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer&apos;s knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. Method The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or dia-magnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. Description of Apparatus Of many alternating-current bridge methods applicable,3 the one shown in Fig. 1 (Owen&apos;s bridge&apos;) was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by PlL1. It is connected to the bridge by about

Jan 1, 1946

By R. G. Patterson

The usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired sue and shape, and in one method1 a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averag- ing a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer&apos;s knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. Method The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or dia-magnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. Description of Apparatus Of many alternating-current bridge methods applicable,3 the one shown in Fig. 1 (Owen&apos;s bridge&apos;) was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by PlL1. It is connected to the bridge by about

Jan 1, 1946

By T. E. Tietz, J. E. Dorn

Activation energies for creep of copper at intermediate temperatures, where crystal recovery was negligible, were determined by the simple technique of rapidly alternating the test temperature between and T2 (T2 = TI + about 10°K) throughout a constant stress creep test. The activation energy for creep H was found to be 37,000± 3,000 cal per mol, independent of stress and strain. The same creep laws as have been previously established for high temperature creep were found to be valid for creep at intermediate temperatures. But the AH was found to be lower than that for self-diffusion in the intermediate temperature range whereas it is known to be equal to that for self-diffusion at high temperatures. IT is now well established that creep at high temperatures can be correlated by the functional relationship&apos;-" e = f(?) s = constant [I] where E is the total plastic strain, f is the function that depends on the stress, ? = f e -- dt, t is the duration of test, e is the base of natural logarithms, AH is the activation energy for creep, R is the gas constant,T is the absolute temperature, and s is the stress. Thus, identical values of are achieved during creep under a given stress at two alternate temperatures at the same total strain. At the same strain therefore where subscripts refer to the two alternate temperature conditions of test. Consequently, the activation energy for high temperature creep is readily obtained with the aid of Eq. 2. Activation energies so obtained have been observed to be insensitive to the creep strain at which they are evaluated, the applied stress, grain size, minor alloying additions,&apos;-&apos; cold worked state, and the presence of thermally stable dispersions of intermetallic compounds in an a solid solution matrix Furthermore, the activation energy for high temperature creep is very nearly equal to that for self-diffusion in all cases where adequate data are available for comparison." " The apparent identity of the activation energies for high temperature creep and self-diffusion strongly suggest that high temperature creep arises from a dislocation climb process. This hypothesis is further strengthened by the fact that the energy of activation for high temperature creep is insensitive to the applied stress," and by the observations that the correlation suggested by Eq. 1 cannot be ex- tended to temperatures below those for rapid crystal recovery. When using the activation energy for self-diffusion, Eq. 1 fails to give the required correlations between creep curves at various intermediate temperatures.&apos; This suggests that the dislocation climb mechanism for creep might be superseded by some alternate mechanism in the intermediate range of temperatures. This investigation was initiated in a preliminary attempt to ascertain the type of creep law that might be valid in the intermediate range of temperatures. Special consideration, however, was given to the determination of the activation energy for creep in this range because the Becker-Orowan&apos;, " and the Mott-Nabarro10 theories for transient creep suggest that the activation energy should increase

Jan 1, 1957

By J. H. East, E. R. Maize

Probably no other type of equipment is now being introduced into American underground mines about which less is known and about which there is more misinformation than the Diesel mine locomotive. Any equipment installed underground brings with it hazards that were not present before, and it is the purpose of this paper to show that Diesel-powered equipment can be used with safety in underground mining if certain feasible but very important precautions are taken. Diesel locomotives are not new in underground mining, since they have been used successfully in European mines for at least 19 years, but their use in American mines is exceedingly limited; so far as is known, only five Diesel mine locomotives are operating at present in United States mines. Diesel locomotives were permitted underground in Great Britain for the first time in 1939, and the rapid increase in the number in use in those mines testifies to their safety and efficiency. More than 1300 Diesel mine locomotives are in use in European mines, according to the latest statistics; these locomotives are employed in coal, iron, lead-zinc and mercury mines. SO far as is known, the Diesel mine locomotive has not yet caused an explosion or mine fire, and has not been the cause of any fatalities from toxic gases in the mines in which it has been used. Adjustments of Diesel Engines foR Underground Use A Diesel engine adjusted to work in an underground mine should not be confused with the same engine adjusted for use outside the mine. Adjustment of the air:fuel ratio for engines that are used on the surface is intended to give the maximum fuel economy, and little or no attention is given to the chemical composition of the exhaust gas produced. Many such engines are poorly adjusted and perhaps poorly maintained, with the result that the engine emits smoke in quantity as well as the disagreeable odor familiarly associated with Diesel engines. The air:fuel ratio in the case of Diesel engines operated on the surface is generally around 15:1; that is, 15 lb of air to burn I lb of fuel. Diesel engines adjusted to work underground usually have an air:fuel ratio of about 20:1, as at this ratio the minimum quantity of toxic gases is given off in the engine exhaust. Diesel engines operated underground must be maintained in better condition than similar engines used on the surface; otherwise, the smoke emitted in the exhaust becomes objectionable if not unendurable. Practically normal air is required for safe operation of Diesel engines underground or in confined places; failure to provide virtually normal air for Diesel engine operation is almost certain to result in trouble. Bureau of Mines engineers have determined that the air in which a Dicsel Operates hi confined places should contain less than % pct of carbon dioxide and at least 20 pct of

Jan 1, 1949

By Henry H. Angst

Tim history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. The elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,000 tons of ore and 18,000 tons of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4 1/2-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. EQUIPMENT On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-dump trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4 ½ -cu, yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1941

By W. M. McCardell, W. O. Winsauer, M. Williams

The mechanism by which an electrical potential difference is developed between two salt solutions separated by shale is shown to be a consequence of the electrical double layer of the shale surfaces. A mathematical derivation is presented to show -the dependence of the potential on the shale characteristic.? and on the concentration of the salt solutions. The equations developed describe adequately the potential-concentration behavior of a long shale core. The equations also describe the variation of potential of sand-shale mixtures with variation of clay content. Ion adsorption i* an important factor in he developments of the surface charge on the shale. and electrical resistivity and ion transference number data are emlployed to estimate the increase of surface charge with concentration. Since the potential is shown to be dependent on the characteristics of the particular .system. water salinities estimated from the potential log by previously proposed methods may be low in some rase;. INTRODUCTION That the electric well log exists today may he attributed to the ingenuity of the Schlumberger brothers who adapted to the logging of wells techniques which were originally developed as surface prospecting methods for the location of ore bodies Empirically it was found that the potential curve of the electric log usually gave values for clean sands which were negative with respect to the values for shales. It was suggested that the potential was responsive to porosity. It was postulated in explanation? that the potential was the sum of a streaming potential, which differed for sands and shales, and of an "electro-chemical" potential of undetermined origin. Mounce and Rust in 1943 showed that the streaming potential is small in most cases and that the potential is generated by a process in which shale and a salinity difference play-essential party. Dickey.:&apos; in the same year, concluded that the potential is dependent upon adsorptive properties of reservoir rock. Wyllie in 1949. and Wyllie and Patnode, in 1950, measured the potential-: between two salt solutions separated by barriers of either naturally-compacted or artificially-compacted shales and concluded that the potential can be expressed by where E is the potential R is the gas content F is Faraday&apos;s constant T is the absolute temperature are the activities of the two uni-univalent solutions These authors postulated that shale. in the ideal case is impermeable to the migration of negative ions. Any potential less than the "ideal" shale potential was considered to be due to imperfections in the shale barrier. Although the studies by Wyllie and Patnode of the development of the shale potential are fairly recent. investigators in fields other than well logging have discussed the mechanisms responsible for analogous potentials over a period of several decades. Although it is evident that much thought has been devoted to the question of the origin of the potential observed in wells, it is also apparent that all of the explanations presented to

Jan 1, 1953

By H. Eyring, J. W. Fredrickson

Many theories have been advanced to explain the phenomena of elastic and plastic deformation. The object of this report is to present a mechanism for deformation, not radically differing from existing theories, but embodying.certain principles and concepts of these theories. This proposed theory cannot be the complete answer to the age-old problem of deformation but it is believed that it will be a step further in the proper direction. The plastic properties of solids have recently been reviewed by Seitz and Read.&apos; ZenerZ has reviewed and correlated the existing work on the anelasticity of metals. With these and others3&apos;4&apos;5 resent theories of deformation are well-known. Of the many theories now extant, those receiving most attention have been proffered by Griffith,6 Becker,l Smekal,8 Polanyilg Orowanlo and Taylor.&apos;&apos; Although differing quite widely in details, these theories are based more or less on a common principle of flaws or dislocations that exist in the crystal lattice. The effect of stress concentrations surrounding a flaw or crack has been treated most recently by Fisher and Hollomon.12 The various authors differ as to the exact nature of the flaws or dislocations, the causes of their appearance, or the manner in which they initiate slip. All of the theories agree that the number of dislocations increases with progressing deformation. It is universally agreed that the shearing process is not a simple gliding of ideally perfect atomic lattice planes. It is also agreed that the "macroscopic" process of gliding, or slip, is brought about by the spreading of a large number of locally initiated "glide steps" through the whole crystal. The occurrence of these "glide steps" is closely related to the presence of some kind of deviations from the "ideal" lattice structure, even in the undeformed crystal. These deviations are overcome &apos;&apos;one at a time," in a manner of speaking, due to some stress-concentrating effect.13 Proposed Theory Many solids show a continuously increasing deformation if subjected to a constant load of suitable magnitude in an extended range of temperature for a sufficient time. This deformation, or flow, may be said to be due, in general, to the tendency of the atoms or molecules in an elastically stressed body to readjust themselves in such a way that if the deformation were kept constant, a release of stress would take place. If rupture does not occur, this process of relaxation causes the rate of flow to obtain a final constant value, as shown in the curve (Fig I) obtained by Taylor and Quinney.14 In this state the release of stress by relaxation exactly counterbalances the increase due to the elastic strain on the test pieces.

Jan 1, 1949

By Henry Eyring, Jay W. Fredrickson

MANY theories have been advanced to explain the phenomena of elastic and plastic deformation. The object of this report is to present a mechanism for deformation, not radically differing from existing theories, but embodying certain principles and concepts of these theories. This proposed theory cannot be the complete answer to the age-old problem of deformation but it is believed that it will be a step further in the proper direction. The plastic properties of solids have recently been reviewed by Seitz and Read.1 Zener2 has reviewed and correlated the existing work on the anelasticity of metals. With these and othersa3,4,5 present theories of deformation are well-known. Of the many theories now extant, those receiving most attention have been proffered by Griffith,6 Becker,7 Smekal,8 Polanyi,9 Orowan10 and Taylor.11Although differing quite widely in details, these theories are based more or less on a common principle of flaws or dislocations that exist in the crystal lattice. The effect of stress concentrations surrounding a flaw or crack has been treated most recently by Fisher and Hollomon.12 The various authors differ as to the exact nature of the flaws or dislocations, the causes of their appearance, or the manner in which they initiate slip. All of the theories agree that the number of dislocations increases with progressing deformation. It is universally agreed that the shearing process is not a simple gliding of ideally perfect atomic lattice planes. It is also agreed that the "macroscopic process of gliding, or slip, is brought about by the spreading of a large number of locally initiated "glide steps" through the whole crystal. The occurrence of these "glide steps" is closely related to the presence of some kind of deviations from the "ideal" lattice structure, even in the undeformed crystal. These deviations are overcome "one at a time," in a manner of speaking, due to some stress-concentrating effect." PROPOSED THEORY Many solids show a continuously increasing deformation if subjected to a constant load of suitable magnitude in an extended range of temperature for a sufficient time. This deformation, or flow, may be said to be due, in general, to the tendency of the atoms or molecules in an elastically stressed body to readjust themselves in such a way that if the deformation were kept constant, a release of stress would take place. If rupture does not occur, this process of relaxation causes the rate of flow to obtain a final constant value, as shown in the curve (Fig I) obtained by Taylor and Quinney.14 In. this state the release of stress by relaxation exactly counterbalances the increase due to the elastic strain on the test pieces. .

Jan 1, 1948

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie- Illinois Steel Corporation. Clairton By-Product Coke Plant And Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By John E. Conley

THE slate industry of the United States has shown a marked decline in value of products made annually since the peak year 1925, although there has been moderate improvement over the lean years 1932 to 1934. In 1940, the value of all slate products sold was approximately 5 ¾ million dollars for a total output of 473,450 short tons. The quantity sold was a little less and the value a great deal lower than the annual averages for the past two decades. Enormous quantities of waste materials result from the quarrying, splitting and milling of slate. Obviously, utilization of such waste material is desirable, not only from the viewpoint of economical operation but also for the purpose of conserving natural resources. One possible use is to produce expanded or puffed lightweight aggregate for use in concretes. Such concretes are strong enough for specific uses, and the advantage of lightness could be obtained in such structures as the walls and roofs of buildings, suspension-bridge roadways and various other applications where weight is a factor. Conceivably, these uses could consume an appreciable annual tonnage. USE OF WASTE SLATES FOR MAKING AGGREGATES The lightweight-aggregate industry has been discussed elsewhere4.5 and need not be covered in detail in this paper. The materials commonly utilized are naturally occurring aggregates such as volcanic cinder, tuff and pumice; by-product materials, such as ordinary cinders and air-cooled slags; and the specially manufactured products, including Haydite, Pottsco, Gravelite, Cel-seal, Superock and Waylite. Slates, however, have not been given the consideration they merit, especially in the United States. In the British Isles, some work has been done3 on certain Welsh slates by the Building Research Station to stimulate the use of these wastes. REQUIREMENTS FOR RAW MATERIALS As pointed out by Hughes,4 the light-weight-aggregate industry is segregated in regions adjacent to large cities in order to localize the market and avoid the necessity of long freight haulage. Waste slate from the deposits of eastern Pennsylvania, northern Maryland, and Virginia would meet the basic requirement of any low-priced structural raw material. One apparent advantage is attained when slate waste, normally discarded, is utilized in the manufacture of a by-product. Mining or quarrying costs usually have been assessed against the main product. Some additional grinding might be desirable, but this operation would be relatively cheap, as most slates grind easily. It is believed that virtually all slates, when properly heated, will expand to some degree. However, types that will expand from 3 to 7 times their original volume are preferred. Fig. I illustrates the expansion of a Pennsylvania slate. The cube originally

Jan 1, 1942

By A. H. Daane, B. J. Beaudry

The Sc-Ti system was studied by thermal, metal-lographic, and X-ray methods. Scandium was found to transform at 1334 °C from a (hexagonal) to ß which was concluded to be bee since a continuous series of solid solutions is formed between ß scandium and ß titanium at elevated temperatures. There is a minimum in the solidus at 51 wt pet Ti and 1300°C, a monotectoid at 1050°C and 49 wt pet Ti, and a eutectoid at 875°C and 91.5 wt pet Ti. The maximum solubility of titanium in a scandium is 13.5 wt pet at the monotectoid temperature, while the maximum solubility of scandium in a titanium is 6.5 wt pet at 875°C. SCANDIUM, a member of Group 111 A of the periodic table, and now called a rare-earth metal,&apos; has become of interest recently due to its low density (2.99 g per cc) and relatively high melting point (1539°C).Spedding,&apos; et al. have described a method of preparation of pure scandium metal and have made a study of its basic properties. Since scandium is approximately 10 to 12 pet smaller in at. diam than the other rare earths while its electronegativity and valence are the same, a knowledge of its alloying behavior in contrast to these elements should be very helpful to fundamental alloy theory. Since scandium is quite scarce and difficult to prepare in pure form, its use as a structural material by itself seems quite unlikely. However, its use in special cases as an alloying addi- tive to other low-density materials is a possible application; the Sc-Ti system was chosen for this reason and for others of fundamental interest. Scandium was suspected of having a high temperature bee form as do some of the other rare-earth metals.3&apos;4 Since titanium has a high-temperature bee form, a continuous series of solid solutions at elevated temperatures between ß scandium and ß titanium would prove the existence and structure of the high-temperature form of scandium. The existence of a continuous series of hexagonal solid solutions at room temperature was predicted by Burkhanov and Savitskiy,5 but Hias shown to be incorrect in early X-ray studies. EXPERIMENTAL METHODS Materials. The metals employed in this investigation were crystal bar titanium and distilled scandium prepared by the method described by Spedding,2 et al. The major impurities are listed in Table I in PPm. Alloy Preparation. All the alloys examined were initially formed in a nonconsumable electrode are-melting furnace under an atmosphere of purified helium or argon. A curve based on the observed weight loss of 0.6 pet* when titanium was melted

Jan 1, 1962