Search Documents

By L. H. Cadoff, L. M. Adelsberg

The layer growth method has been used to investigate the reaction kinetics of liquid titanium and hafnium with carbon and the [liq] - [liq + TiC] and [liq] - [liq + HfC] phase boundaries at temperatures above 1800°C. The equipment and experimental procedures used in this investigation are basically identical to those described in an earlier paper' on the Zr-C reaction. Temperature control, however, was improved significantly by connecting a Latronics Colo-Ratio automatic pyrometer and a controller to the power source. The subsequent temperature variations were ±10°C; previously ±20°C was obtained using manual controls. The absolute accuracy of the pyrometer, however, must be considered to be only ±40°C.* The spectrographic analyses of the materials used in this study are listed in Table I. The isothermal reactions of titanium (1800° to 2700°C) and hafnium (2300" to 3000°C) with carbon (graphite crucibles) resulted in the formation of carbon-saturated liquid metal and layers of Tic and HfC, respectively. The thicknesses of the carbide layers, determined from metallographic measurements at 100 times, as a function of carburization time and temperature are given in Figs. 1 and 2. At each temperature, parabolic growth behavior for these reactions was observed and could be expressed as x2 =Kpt, where X is scale thickness (corrected for heating and coolingL), Kp the parabolic growth constant, and t the isothermal carburization time. Values of Kp as a function of temperature for the carbides are shown in Fig. 3 and listed in Table 11. The growth constants are expressible as: kpTiC = 0.2 exp(-61,800/RT) sq cm per sec for Tic and Kp HfC = 2.62 exp(-95,300/RT) sq cm per sec for HfC. The liquidus phase boundaries were determined from metal samples treated in graphite crucibles for different times ranging from 4 to 100 min at each of the temperatures indicated in Table 11. Metallographic examination revealed that the carbide precipitates were distributed uniformly throughout the frozen metal matrices. This is attributed to the rapid cooling rates (800°C per min) and the small difference in density between the precipitated carbide and the liquid metal.

Jan 1, 1968

By M. C. Cheney

The active development of the vast East Texas oil field, the attendant effects of the rapidly increasing flow from its prolific wells and the efforts to bring order out of chaos precluded or dwarfed other oil development in Texas during 1931. In a paper by Dr. F. H. Lahee1 presented at the October, 1931, meeting, the early history of the East Texas oil field is described and the sequence of events in connection with its development and efforts to control its production up to Sept. 25 is narrated. At that time the Railroad Commission of the state reduced the production of the field to a maximum of 400,000 bbl. per day by restricting the allowable daily production per well to 185 bbl. By further reduction in the daily production per well to 100 bbl., the field was held below that maximum figure during the remainder of the year. Meanwhile, as a result of an injunction against the Railroad Commission, its authority in the field was superseded on Oct. 13 by the Governor of the state, and after that date production was controlled directly by his orders issued under authority of martial law. Suits to contest this authority were brought in the Federal courts and were pending at the close of the year. On March 5, 1931, as a result of the East Texas production, posted prices for Mid-Continent 40' A.P.I. crude slumped from $1.07 to $0.67. As East Texas production continued to mount, posted prices in East Texas were reduced to $0.37 on June 3 and $0.22 on July 8, although in that field most of the oil was sold for much less, bringing the producer and royalty owner as low as $0.025 per barrel. Northeast Texas To the information contained in Dr. Lahee's paper, it can now be added that the East Texas field has produced over 105,000,000 bbl. and registered about 3700 successful completions during 1931. There may be some merit to the recent prediction that a large part of the field will have passed its flowing period by the middle of 1932 unless

Jan 1, 1932

By R. M. Caitlin

QUITE a number of years ago in looking for basic facts, it seemed obvious, in view of an unquestion-able supply of raw material and an extensive requirement probable in the near future, that the funda-mental requirement of any shale-oil industry was mass production 'by a continuous process. This decision greatly simplified matters, as it eliminated all considera-tion of externally-heated retorts, and all batch processes, which only utilize a part of the capacity of the interior space because, unless the ashes are removed as rapidly as formed, the space occupied by them is dead, instead of being occupied either by shale in active distillation or in drying out and heating up preparatory thereto. A second imperative and basic necessity soon appeared as a natural sequence, namely, the fixed carbon of the spent shale must be utilized to supply the heat for the eduction of the oil. PRODUCTION OF THE CRUDE As the production of the crude oil is the first and most important step in the utilization of oil-shale, being the only source from which the multitude of possible by-products can come, each by a special treatment of the crude oil, I will devote the time allotted to me to the subject of crude oil production-its cost expressed in terms of tons treated per man per shift. The costs of mining the shale and refining the crude shale oil vary with local conditions and are not specially influenced by the source of the crude. But the cost of distilling the shale in terms of tons per man shift seems to be the basis of any proper comparison of costs. After considerable experimenting, ranging from laboratory tests up to and including quantities of fifteen to twenty tons, it was evident that a plant might be made up of an indefinite number of units operating in concert. The economic size of the units, however, would .have to be determined by experiment. The general theory of our process contemplates a regulated combus-tion of the fixed carbon in the spent shale, in its incan-descent condition after all the oil has been driven out of it; and a transfer of the resultant heat to the mass of raw shale above.

Jan 1, 1927

By Ole Singstad

The legislatures of New York and New Jersey, determined in 1919 that a vehicular tunnel should be built under the Hudson River. On July 1, 1919, an engineering staff was organized with the late Clifford M. Holland as chief engineer. After preliminary investigation it was decided to build the tunnel from Canal St., New York, to 12th St., Jersey City, which is the center of the heaviest traffic across the Hudson River. It was also decided to build two tunnels—one for west-bound traffic and one for east-bound—the tunnels to be of cast iron, built up of segments and bolted together, each tunnel to have a roadway 20 ft. wide and a clear head room of 13 ft. 6 in. The tunnels have an exterior diameter of 29 ft. 6 in. The interior lining is of concrete, the sidewalls, tiled with a vitreous white tile, and the roadways are paved with granite block. The entrances and exits at both ends are separated by two blocks so as to reduce traffic congestion. Basis of Ventilation It was recognized very early that one of the most important problems confronting the engineers was a proper ventilation system. It was estimated that each tunnel as planned would have a traffic capacity of 1900 vehicles per hr. The tunnels are 8500 ft. long between portals, and it was considered that the ventilation should be based on all of these vehicles being operated by gasoline engines. That presented a problem in ventilation unlike any other either in magnitude or character. There have been vehicular tunnels built in Europe, principally in London, but they are shorter and have a smaller traffic capacity. Up to the present time, at least, they have handled a very large percentage of horsedrawn vehicles so that the necessary ventilation has been provided for by the natural draft through the portals and open shafts. Within the last few years, however, a small mechanical ventilating plant has been installed in the Blackwall Tunnel, which has been in operation about 27 years. I might mention that at the time this work was started, it was considered by many that the problem of ventilation was insuperable and it

Jan 1, 1927

The opening session of the Institute was held at Hazle Hall, Tuesday evening, October 27th, with a large attendance of members. President Raymond called the Institute to order, and after a few introductory remarks, introduced Mr. I. Lowthian Bell, President of the Iron and Steel Institute of Great Britain, and Honorary Member of the American Institute of Mining Engineers. Mr. Bell was received with great applause, and made his acknowledgments in a brief speech, of which the following is the substance: He desired to thank the Institute personally for the honor conferred upon him in his election to membership, and also for the invitation extended last year to the body of which he was President. The difficulty felt by many members of the Iron and Steel Institute, of leaving for a long journey the works of which they had charge, aggravated by special industrial troubles at the time of the invitation, had obliged them to conclude that it could not then be accepted in a fitting manner. The iron .manufacture of this country is a subject of great interest to Englishmen, who look with pride upon the achievements on this side the water of the descendants of a common ancestry. His own reception in this country had far surpassed in cordiality even the well-grounded anticipations he had formed from the assurances of the President and other friends. Notwithstanding the flattering manner in which his friend, in introducing him to the Institute, had spoken of his contributions to the science of iron metallurgy, he could not take to himself alone the significance of this welcome. He knew it was a recognition of the services rendered by the body which he had the honor to represent; and he was glad to see present a member of that body, Mr. Thomas Whitwell, who had fortunately been able to make the journey at this time, arid whom he had had the pleasure of meeting on the shores of Lake Champlain. He had been requested to say something of his impressions of the American iron industry. It was not easy to digest so soon the vast

By Zay Jeffries

THE history of the development of our great iron and steel industry has been recorded in many publications, not the least important of which are the TRANSACTIONS of the American Institute of Mining and Metallurgical Engineers. During the life of the Institute, of less than 60 years, the annual production of pig iron in the United States has increased more than 23 times. Such a rate of growth may seem small when compared with that of the automotive industry, which has increased 100 times in the last 20 years, or when compared with the growth of other industries of recent birth. The comparison appears less unfavorable, however, when the fact is taken into consideration that the iron and steel industry has existed on the earth in some form for thousands of years. The trade journals, the Department of Commerce and technical societies keep us currently informed concerning technical and corporate developments and the statistics of the American iron and steel industry. Merely to describe the high spots of the industry as it exists today would require a book of no small size. It involves the utilization of about 900,000 people, the payment of $1,400,000,000 in annual wages and salaries, the-investment of $14,000,000,000, the mining annually of 70,000,000 tons of iron ore, 15,000,000 tons of limestone, and 120,000,000 tons of coal. It results in the production of 40,000,000 long tons of pig iron and 50,000,000 long tons of steel ingot. In addition, the industry includes ownership and operation of railroads and steamship lines, the production of cement, timber, coke, gas, by-products, and many other activities. The leading part played by the iron and steel industry in promoting the confidence of the public in corporations and corporate management is well known. The industry has also provided worthy examples of vertical integration and mass production. The social activities within the industry have been no small factor in promoting the fuller development and greater happiness of the American working man-and his family. In this connection I advise reading a paper by Theodore W. Robinson,1 which

Jan 1, 1930

By William Sharp

DISCOVERY of new ore in the Eureka district, Nevada, as a result of bold and persistent exploration based on a geologic interpretation of structure has recently aroused wide comment in mining circles. It may therefore be of interest to the profession to have a summary of the historical background and an account of the recent program of development. The mines of Eureka, discovered in the late 1860's, were the first important silverlead mines in the United States. They have a production record of more than fifty-one million dollars.1 After the ore bodies were apparently bottomed in the 1880's, repeated attempts to find new ore were unsuccessful until 1940, when a diamond-drill hole cut a 40-ft width of sulphide ore 1409 ft below the 841-ft level of the Locan shaft. The next hole cut 30 ft, of ore and three additional holes drilled in 1943 and 1944 showed the ore body to be continuous, Shaft sinking to reach and open up the ore body has been in progress since 1945. GEOLOGY Stratigraphy The ore in the Eureka district occurs in a series of Cambrian sediments which is exposed through a thickness of over 6000 ft. The stratigraphic column is as follows:2 [THICKNESS, FI ORDOVICIAN Pogonip limestone (upper part). Thin bedded limestone with some chert. UPPER CAMBRIAN: Pogonip limestone (lower part). Thin-bedded limestone (with shaly limestone and chert).... 425+ Dunderberg shale. Shale (clay and calcareous shale) and thin bedded limestone340+ Hamburg dolomite. Dolomite and limestonegoo+ MIDDLE CAMBRIAN: Secret Canyon shale. Shale and thin-bedded limestone1,035 Geddes limestone. Carbonaceous, flaggy limestone with some shale partings 335 MIDDLE (?) AND LOWER CAMBRIAN: Eldorado dolomite. Dolomite and limestone2,000 LOWER CAMBRIAN: Prospect Mountain quartzite. Quartzite with occasional inter calated conglomerate and shale 1,660+ The Prospect Mountain quartzite has been subdivided into two formations: Upper part, Pioche shale. Shale, quartzite with some intercalated limestone (Lower Cambrian fossils)-200 ft. Lower part, Prospect Mountain quart zite proper-I,460+ft. Total thickness6,695+] Much the most productive of these formations has been the Eldorado dolomite, which yielded more than $42,000,000 at Ruby Hill and an additional amount

Jan 1, 1947

By R. H. Tien

This paper presents an analytical solution of the problem of freezing of a semi-infinite slab with constant surface temperature; in this analysis accoz~nt is taken of the heat evolution during the solid-state transformations in the frozen skin. The regions where transformations occur are treated as plane isothermal heat sources; i.e., the rates of transformations are assumed to be infinite. In the model considered, three plane heat sources are assumed to be present in the frozen solid. The solution yields the temperature distribution in the solid, the rates of movement of the heat sources , and the rate of movement of the solidification front. It is shown that, although the sum of the heats of transformations in the solid is about 20 or 43 pct of the heat of fusion of iron or manganese, respectively, the effect of the heat evolution in solid-state transformations on the rate of solidification is insignzficant. IN several recent mathematical studies of solidification of liquid metals'-3 no account was taken of the heat evolution accompanying the solid-state transformations. In the case of, for example, steel, there are several phase transformations 6 -y, y -a, and the magnetic transformation. Whether or not a significant error is introduced into the mathematical simulation of solidification processes by the omission of the heat effects associated with these phase transformations is not known. The purpose of the present study is to investigate the effect of these phase transformations on the temperature distribution and the rate of solidification based solely on the heat transfer point of view. That is, for the sake of simplicity, freezing of a pure metal with solid-state transformations will be considered. The mathematical model which represents the present problem includes four moving heat sources representing freezing and phase transformations, 6— y — a — ferromagnetic. The thermal properties such as conductivity and specific heat, and so forth, are different from one phase to the other. But they are considered to be uniform over any particular phase. The usual Fourier heat flow law is employed. The concept of conservation of energy is applied at every heat source in order to estimate their rate of movement. The temperature distribution in the solid and the positions where transformations occur are expressed analytically in terms of error function solutions and four coefficients which are determined from four nonlinear algebraic equations. These coefficients can be calculated either by trial and error or by any numerical method. MATHEMATICAL ANALYSIS Fig. 1 is a schematic diagram showing the zones of different phases 1, 2, 3, and 4 in the solidified portion of a semi-infinite pure liquid metal. The heat is subtracted from the system at x = 0 which is maintained

Jan 1, 1968

By R. A. Corley, W. R. Wilcox, J. R. Teviotdale

Chemical vapor deposition of hafnium carbide yielded whiskers, needles, dendrites, faceted crystals, and adherent coatings. The gas stream compositiom and the mass transfer conditions determined the habit of the deposit. The deposits were obtained at temperatures ranging from 1100" to 1800°C. HAFNIUM carbide has the highest melting point of any binary compound; therefore, its various potential applications are a subject of vital interest to the aerospace industry. The experiments described herein were performed to investigate the chemical vapor deposition of hafnium carbide with particular interest being placed upon the possible production of high-strength single-crystal whiskers for composite materials. In 1931 Moers 1 used a gaseous mixture of HfC14, Hz, and toluene to vapor deposit crystalline hafnium carbide on a tungsten filament heated to 2400°to 2800°C. More recently Lepie 2 deposited hafnium carbide on graphite using HfC14 and methane in a helium gas carrier. The pyrolytic depositions described here were accomplished in graphite tubes by using various gas mixtures and dopants. The resulting crystal habits included whiskers, needles, needle dendrites, bulbous dendrites, faceted crystals, and smooth, adherent poly-crystalline layers. EXPERIMENTAL The depositions were carried out in an induction-heated graphite tube, 1.2 cm ID, which was contained in a vertical 9-cm-ID quartz tube. (A more detailed account of the experimental procedures and results is given in Ref. 3.) Refractory oxide fiber and tubes and graphite felt were utilized jointly and singly for therma1 insulation. A typical temperature distribution is shown in Fig. 1. The reactant gases were introduced at the top and removed at the bottom of the tube. Table I summarizes the experimental conditions and results. Many deposition habits were obtained. X-ray analyses showed that they possessed the hafnium carbide structure. Almost invariably these formed well above the point of maximum temperature in the graphite tube. The habit depended strongly on the gas composition. In a series of runs (e.g., run A) using HfC14 and toluene in H 2, hafnium carbide coatings, Fig. 2, were reproducibly obtained at the position where the tube wall was 1400°C, and bulbous dendrites, Fig. 3, were

Jan 1, 1969

By T. J. Nowak

The heat flow processes determining the injection and shut-in temperature logs in a water injection well have been analyzed and the theoretical basis for determining the water injectivity profiles from the temperature logs has been presented. Both the injection and the subsequent shut-in logs are necessary to resolve the injection interval into relative water intake strata; the former, to provide an accurate estimation of the thicknesses of the strata, and the latter to indicate the major and minor intake rates into the strata. A procedure is described for estimating the injectivity profile from the temperature logs and is applied to several temperature logs. For a water injection well, a comparison is made of the injectivity profiles obtained from the core analysis, the spinner survey, and the temperature logs. INTRODUCTION In secondary recovery of oil by water flooding, the injectivity profile is needed to obtain diagnostic evaluation of water intake distribution over the injection interval. If the distribution is unfavorable among the various strata, corrective measures can be taken to provide better control. Numerous methods have been developed for determining the injectivity profile from water velocity measurements in well bores. Often, dependence is placed upon core analyses and/or electric logs for estimating the relative water intakes over the injection interval. In many cases, the temperature log method described herein will give results more diagnostic than those obtained through use of the other available methods inasmuch as it is based upon the study of temperature disturbances in and around the well bore as a function of water flow in the well bore and in the formation. This method is the result of analyses of a number of temperature surveys made in water injection wells to determine the point of entry of the water into the formation. The material in this paper is presented in two sections: the first deals with the theoretical study of temperature survey data, and the second deals with the field application. PART I — THEORETICAL TREATMENT OF TEMPERATURE LOG DATA Before discussing the various aspects of heat flow relative to temperature log data, the phenomena that give rise to well bore temperatures — namely, the indigenous formation temperature and the associated rates of heat flow — will be considered. Geothermal Gradient The geothermal gradient is defined as the increment of depth at which the indigenous subsurface temperature increases by l°. It is caused by the continuous flow of heat outward from the interior of the earth. The flow of heat is an equilibrium process between the heat sources, the thermal conductivities of the formations, and the mean surface temperature. Therefore, there is no accumulation of heat energy in the path of heat transmission, and the geothermal gradient for a given formation will depend upon its thermal conductivity.

Jan 1, 1953

Homestake's Bulldog Mountain Operation near Creede, Colorado, in the San Juan Mountains at an elevation of nearly 2,750 m (9,000 ft), is subjected to short summers and long cold winters. Creede’s history dates back to 1889 when silver ore was discovered; and by 1892 production of over a million dollars per month was being shipped from mines located along the Amethyst Fault. The Bulldog Mountain Fault remained relatively untouched by the early prospectors. The United States Geological Survey recognized the potential of this fault in 1960, which led to the staking of many claims over the structure. Homestake leased properties in 1963 and in mid- 1964 a tunnel was started at the 2,956 m (9,700 ft) level with encouraging mineralization being encountered. In 1968 a decision was reached to build a flotation mill of 318 mtpd (350 stpd) capacity. The erection of the mill was completed in early 1969, six years after the first exploration was begun. Since initial start-up, extensive drifting has been done on several separate levels. Two underground hoist installations serve the various levels and many thousand feet of vertical mining operations. Due to the unconsolidated nature of the vein, a new unique underhand cut-and- fill mining method was developed. This procedure is the reverse of the normal cut-and-fill and proceeds from the top down under cemented sand fill, which, while expensive, has greatly reduced s toping hazards. Prior to 1977, a considerable quantity of silver was lost in the slime fraction of the ores processed because of oxidation and other inherent characteristics of individual minerals. Due to Homestakefs favorable experience in treating the slime fraction of the Lead, South Dakota gold ores, experiments with leach methods to recover silver from the slimes by Carbon -In -Pulp offered' the potential for additional silver recovery. Work was begun on the Carbon-In-Pulp plant in April 1976 and completed in December of that year at a cost slightly exceeding $2 million. The C. I. P. plant was designed for 136 mtpd (150 stpd) of current plant slimes plus 227 mtpd (250 stpd) of slimes dredged from the old tailings during the summer season. The sand fraction of the flotation

Jan 1, 1981

By W. C. Bednar

In all, 127 producing oil wells, 8 producing gas wells and 212 dry holes were drilled during 1936 in the Central Texas area; 76 wells in Bexar County, 62 in Caldwell County, 44 in Guadalupe County, 22 in Williamson County, 20 in Navarro County and 20 in Frio County. Less than 20 were drilled in each of the other counties and none at all in Ellis, Hill, Bosque, Coryell, Lampasas, Burnet, Llano, Kennedy, Mason, Real, Kinney and Uvalde Counties. The Pearsall-Austin chalk field in Frio County and the Zoboroski field in Guadalupe County were the only new discoveries and there were no important extensions to old fields. In this report Corsicana, Mildred (Elm Ridge), Angus-Edens-Hodge, Burke, and Rice-Oil Ridge, all shallow Navarro County stripper fields, are grouped together under the name of Corsicana. This grouping follows that of the Railroad Commission of Texas, thus facilitating the gathering of production data. A map showing the location of the oil and gas fields in the Central Texas Area was published in Volume 114 of the A.I.M.E. TranBactions, page 380. New Fields Pearsall-Austin Chalk.—The Amerada Petroleum Corporation completed 13 Austin chalk wells during 1936 on the large Amerada-Rycade block in Frio County. Other companies drilled two dry holes to the Austin chalk in this vicinity. Not enough wells were drilled to give control of the structure but it appears to be a nose plunging in a west-southwest direction. A second deep test is being drilled in the Pearsall area and at this writing has cemented off a show of oil and gas in the Edwards limestone. The Humble Oil and Refining Co. is building a 6-in. pipe line from Lytle, Tex., to serve the Pearsall field. Zoboroski.—Actual discovery of the Zoboroski field was made by W. J. Walton et al. in 1931. The discovery well, Anton Zoboroski No. 1, was a small producer making but from 3 to 5 bbl. per day, which was used locally for fuel oil. The discovery of the Darst Creek Extension in

Jan 1, 1937

By E. A. Gulbransen, W. S. Wysong

THE behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotective nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance study 1,2 of the following problems. (11) the oxidation kinetics in the temperature range of 250° to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films, and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 250°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide MoO3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics. time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation The general interpretation of many of these factors has been previously discussed. LITERATURE The oxidation of molybdenum has not been studied critically. Although" many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Culbransen 4 Their results showed that MoO2 is the oxide which is stable in contact with the metallic subgtrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Mo03 is no longer observed, Mo02 being the only oxide found. Hagg and Magneli5 have shown from an X ray study that the a-phase, orthorhombic MoO3 is stable up to 1050°C. Two other phases, ß and ß', with compositions close to Mo02 90 are also obtained The formula for the ß phase is not given but that of the ß' phase is defined as Mo9026. The ß' phase is found to be built upon a monoclinic unit cell. A -?-phase is isolated from a preparation M00275 heated for 17 hrs at 670°C. This phase is

Jan 1, 1947

By W. G. Pfann

The problem of forming points on wires that were from 0.002 in. to 0.010 in. in diam arose in the recent appearance of silicon and germanium point contact rectifiers as elements in microwave radar.' In these devices a pointed tungsten wire makes a delicate contact with the surface of a semiconductor. Because the quality of such rectifiers is largely determined by the nature of this contact, considerable attention has been given to the formation of the metal point. Reproducibility of contour and freedom from burrs and even microscopic irregularities are considered essential. The operations involved must be simple and rapid enough for mass production. Previously tungsten wircs had been provided with conical points by a grinding method which involved rotating a wire about its axis and causing it to bear at an oblique angle against a spinning abrasive disc. This was later complemented with an electrolytic polishing treatment which removed irregularities from the ground point and also rounded it off at the tip—a desirable feature. Finally, these operations were supplanted by the electrolytic pointing method described here. Mechanism of Point Formation The wires to be pointed are partially immersed in an electrolyte in a vertical position whereupon they are provided with smooth rounded points entirely by electrochemical action. The process is independent of the depths to which the wires penetrate the electrolyte because the points are formed at the surface level. It may be used to point a single wire or many of them simultaneously and is applicable to wires of different diameters within a limited range. Solution of the immersed portion of a tungsten wire is accomplished by making it the positive electrode in an electrolytic cell, as shown in Fig I. While the wire is maintained at constant voltage the current through the cell falls continuously, principally because of the decrease in wetted area which results from solution of the tungsten. This increase in resistance occurs in a reproducible manner and is used as a control in the process. As thc immersed portion of the wire dissolves, it remains cylindrical in shape except for the short section which is wetted by the meniscus. Here the rate of solution is lower and decreases as the top of the meniscus is approached. The result is the formation of a tapered section inside the meniscus. As solution continues, the cylindrical section either dissolves entirely or drops off just before complete solution, leaving only the taper which is now sharply pointed. Further action causes this point to become rounded and then quite blunt, until finally the end of the wire is almost plane. Fig 2 shows the stages in this development. Contour PF is most representative of those used in point contact rectifiers. Thus a variety of point

Jan 1, 1949

By M. T. Worley

This paper reports investigative work conducted to develop a method of estimating the groundwater influx from a homogeneous permeable formation into a vertical mine shaft during sinking. A method of analysis was developed using data obtained from pumping tests and a modification of the Theis non-equilibrium interpretation technique. Excess influx of groundwater into mine shafts has long been one of the more important problems encountered in the development of a mining property. Much work has been done on methods of preventing such influx and on pumping schemes to control inflow if preventive measures fail. The fundamental aspects of the problem, on the other hand, seem to have been neglected. The purpose of this paper is to review the fundamentals of groundwater flow and to propose a rapid method of analyzing hydrologic data in order to estimate influx from a homogeneous permeable formation into a mine shaft. Such an estimate of the quantity of water to be encountered is of value in planning grouting, pumping and other programs designed to control that influx. It is emphasized that the proposed method of analysis should be regarded only as a tool to be used in evaluating the problem before investing the capital necessary to begin development of a property. FUNDAMENTALS OF GROUNDWATER FLOW In order to effectively approach the problem of estimating influx into a mine shaft, a knowledge of the fundamentals of fluid flow through a porous medium is necessary. Darcy, in 1856, developed an empirical relationship to explain the flow of water through sand filters. This relationship V = k (dh/dl), is the basis for all other flow formulae. It has been shown that Darcy's relation is a solution of the Laplace equation and thus is analagous to other natural phenomena such as heat flow. Theis, using the analogy of heat flow by conduction, developed an expression for determining the transient or time-dependent groundwater flow through a homogeneous, isotropic medium. The resulting equation Was also derived by Jacob using hydrologic considerations alone.' The individual terms in the equation are described in Table I. It is important to understand the assumptions upon which this equation is based. 1) The medium through which the fluid flows is infinite in areal extent, homogeneous and isotropic. 2) The well into which the fluid discharges completely penetrates the medium. 3) The characteristics of the medium remain constant at all times. 4) The initial pressure surface is horizontal. 5) The confining media are impervious and horizontal. 6) Fluid is removed from storage instantaneously by a decline in pressure. 7) The diameter of the discharge well is infinitesimal with respect to the drainage radius of the medium.

Jan 1, 1962

By P. L. De Bruyn, R. J. Charles

THE transfer of kinetic energy of translation into other forms of energy by impact is a fundamental process in most crushing and grinding operations. During and after the impact process the original source energy may be accounted for in any of the following possible forms: 1) Kinetic energy of translation of both the impacted and impacting objects. 2) Kinetic energy of vibration of the components of the impact system. 3) Potential energy as strain energy of the components of the system or in the form of residual stresses. 4) Heat generated by internal friction during plastic deformation or during damping of elastic waves. 5) New surface energy of fractured materials. At any instant during the impact process only the strain energy of the components of the system can contribute directly to the brittle fracture process. If fracture is the desired result, as in comminution, it would seem advantageous to choose or arrange the conditions of impact so that a maximum amount of the original kinetic energy could be converted to strain energy at some moment during a single impact. The present work deals with determination of these desirable conditions for a simple case of impact and application of the principles involved to general cases of impact. Experimental Method: Longitudinal impact of a rod with a fixed end was chosen as the impact system for investigation. The rod was mounted horizontally and the fixed end was formed by butting one end of the rod against a rigidly mounted steel anvil. The rod, of pyrex glass, was 10 in. long by 1 in. diam with both ends rounded to a 6 in. radius. The rounded ends permitted reproducible impacts on the free end of the rod and assured a symmetrical fixed end. Pyrex was selected as the rod material because of the marked elastic properties of such glass and the similarity of fracture between pyrex and many materials encountered in crushing and grinding operations. The frequency of natural longitudinal oscillation of the rod was 10 kc, and thus simple electronic equipment could be used for observation of strain changes occurring in the rod at this frequency. As shown in Fig. 1, impacts on the free end of the rod were obtained either by a pendulum device or by a spring-loaded gun. Relatively heavy hammers (100 to 600 g) of mild steel were used in the pendu- lum impacts, while fairly light projectiles (20 to 80 g) were fired from the spring-loaded gun. One of the main objects of the experimental work was to obtain the strain-time history of the rod as a function of the mass and kinetic energy of the impacting hammers. For this purpose a technique involving wire resistance strain gages and a recording oscilloscope was employed. Five gages were applied at equidistant sections along the rod, and by means of a switching arrangement the strain-time history at any section, and for any impact, could be obtained in the form of an oscillograph with a time base. The equation relating strain and voltage change across a strain gage through which a constant current is flowing is as follows: e = ?v/iRF [1] ? = strain, ?v = voltage change, i = gage current, R = gage resistance, and F = gage factor (from manufacturer's data — SRA type, Baldwin Lima Corp.). With the above equation an oscillograph depicting voltage change vs time on a single trace can be converted directly to a strain-time diagram if a calibration of the vertical response on the oscilloscope screen for specific voltage inputs is available. In the present case the calibration was obtained by photographing precisely known audio frequency voltages on the same oscillograph as that on which a voltage-time trace from a strain gage had been made. Synchronization of the beginning of the single trace with the beginning of the impact was accomplished by permitting contact of the impacting objects to close an electrical circuit from which a voltage pulse, sufficient to initiate the trace, was obtained. The struck end of the rod was lightly silvered for purposes of electrical conduction so that it would form one of the electrical contacts. Markers every 100 micro-seconds on the traces served for a time base calibration. Determinations of the kinetic energies of translation prior to impact were made in the case of the pendulum hammers by measuring the height of fall of the hammer and in the case of the projectiles by measuring the exit velocity from the gun barrel by means of an electrical circuit employing light sources, slits, and phototubes.' During the experimental work it became evident that the time of contact between the impacting object and the rod was an important variable in the impact process. Measurements of the times of contact were made, therefore, for every impact for which a strain-time record was obtained. The time of contact was determined by permitting the impacting components, when in contact, to act as a closed switch and discharge a condenser at relatively constant voltage. The discharge was observed and photographed with a time base on the oscilloscope screen.

Jan 1, 1957

By D. J. Mottern, F. Wald

SEVERAL systems have been investigated by Bates, Wald, and weinstein&apos; to determine the compatibility of pure PbTe with various metals. This was accomplished by experimentally determining the direction of the reaction given by Eq. [I]: The direction of this reaction is very important if alloys of the PbTe system are to be used in thermoelectric generators because the presence of free lead in the matrix, followed by incipient melting in the vicinity of the hot junction, could cause a bonding failure. According to anssen,&apos; the Au-Te system contains only one stable compound, AuTez. The initial alloy which was reacted was therefore of the composition AuTez + 2Pb. Ten-gram samples of PbTe plus 1, 10, 20, 30, 40, 50, and 70 at. pct Au were encapsulated in carbon-coated quartz capsules in vacuo. All materials were of semiconductor (99.999+ pct) purity. Carbon coating was used to prevent reaction of the quartz with any of the alloying constituents (the solubility of carbon in the constituents of the alloys is negligible). Each capsule was then placed in a thermal analysis furnace, melted, and cooled through the transformation region. Thermal arrests were monitored on a strip chart recorder. Each sample was subsequently examined microscopically after standard grinding and polishing techniques were applied. For better contrast between the phases, the samples were etched in Murakami&apos;s etch; however, both phases could be identified without etching. Several of the samples were ground into powder, stress-relieved, and X-rayed in a Debye-Scherrer camera using nickel-filtered Cu-Ka radiation. The phase diagram shown in Fig. 1 indicates that the pseudobinary system exists as a simple eutectic with no measurable (<I pct) solid solubility at either limit. Figs. 2,3, and 4 are photomicrographs of the structures obtained with 20, 40, and 50 at. pct Au, respectively. At higher concentrations of gold (>40 pct) slight divorcement of the eutectic occurred, apparently due to a) the difference in density between gold and PbTe (19.6 and 8.25 g per cu cm, respectively) or b) the nonideality of the liquid as noted by the curvature of the liquidus lines. The eutectic temperature was determined to be 742° ± 5°C. The composition of the eutectic was determined by extrapola-

Jan 1, 1969

By Leonard Greenburg

The American literature in the field of dust sampling and analysis has been growing rapidly since 1915. Studies made since that time clearly indicate that there are three fundamental factors that determine the production of lung pathology due to dust inhalation. These are the duration of exposure, the chemical and mineralogic nature of the dust and the concentration of the potentially harmful dust. In the estimation of the amount of the potentially hazardous dust there are essentially three problems involved: (I) a determination of the size of the hazardous dust; (2) determination of the most satisfactory apparatus and technique of sampling, and (3) the most satisfactory method of analysis. A complete study of the literature shows that industrial dust varies ill size from ultramicroscopic particles to those larger than lop in diameter and that relatively few particles are found over 5u in diameter. Approximately 10 to 25 per cent are less than 0.811 in diameter and the median size as a rule is found to lie between 1.25 and 1.75 microns. From the point of view of lung pathology the particle sizes of most importance lie between 0.5 and 5u. Of all the instruments for sampling dust the Impinger apparatus is the only one that will sample a larger body of air satisfactorily with small control errors and high efficiency in both low and high concentrations of dust. The Owens apparatus has the advantage of being more portable and somewhat easier to use but it does riot permit of the sampling of large volumes of air. It has a low efficiency in high concentrations of dust and does not permit dust weights to be obtained. From the point of dust-counting technique the author points out that in 1922 considerable experimentation with dark field and oblique illumination resulted in the conclusion that such methods were not readily duplicated from day to day and therefore yielded somewhat erratic results. Changes in the amount of illumination produced variations of several hundred per cent in dust counts obtained with dark ground

Jan 1, 1934

By Michael J. Messel

W. P. MOULD*—Has consideration been given to the problem of retreating the 4,000,000 ton tailings pile to recover the very considerable amount of asbestos fiber that was lost over the years due to insufficient operation and poor recoveries? Also, what was known about the possible content of chromite and the sulphides of nickel and cobalt? M. J. MESSEL (author&apos;s reply)—Consideration was given to the problem but nothing concrete has been done up to this time. W. P. MOULD—I am certain the tail- ings contain a very considerable quantity of fiber, not all of which is in the shortest lengths, because in the milling of talc rock from a neighboring location having a common origin with the asbestos bearing serpentine source of the tailings pile, a concentrate carrying 15 pct Ni and Co in complex sulphides and constituting about 4/10 of 1 pct of the talc rock was recovered. In the belief that the tailings also contained an appreciable content of chromite (then in demand, 1937) it was suggested to the management of the asbestos company that a truck load of the current tailings be sent to the flotation plant of the talc company where it would be put over the concentrating tables in an effort to discover the presence and roughly the percentages of chromite, nickel, and cobalt. Preparations for the test were woefully inadequate and the test was completely snarled up by the surprisingly large quantity of asbestos fiber from 1 in. long down to very short fiber, all of which matted up and plugged launders and pumps with disastrous effects and practically the total loss of the sample. If anything was indicaded by the test, it was that a wet process for milling asbestos was worthy of very serious consideration. M. J. MESSEL—A wet milling process for tailings retreatment only, is at present under study at our plant. One asbestos mining company in Canada has constructed a fairly large test plant for this purpose, but as yet no definite results have been obtained other than in a small test unit plant which were in some respects quite encouraging.

Jan 1, 1950

The oil production in Bahrein for the year 1937 was 7,762,264 bbl., a monthly average of 646,855 barrels. Sufficient potential production had been developed in the Second Pay (Main Pay) at Bahrein by the end of 1936 to supply the anticipated crude demand, and the drilling program was changed from straight development to partial exploration during 1937. Two nonproductive wells were drilled to test the Third Pay at a depth of about 2900 ft., or some 900 ft. below the top of Second Pay. As a result of this exploratory work, the normal drilling program was slowed down and only eight new wells were completed in the Second Pay during 1937, making a total of 45 producers from the Second Pay. The deep test was drilling at 5081 ft. at the end of the year. A 550-ft. section (termed Fourth Pay) of porous limestone interbedded with anhydrite was topped at about 4150 ft. Numerous drill-stem tests indicated that the limestone was very permeable and that it carried large volumes of natural gas under high pressure together with a small amount of high-gravity oil or condensate. Drill-stem tests also indicated that the bottom 50 ft. of the 550-ft. section carried an encouraging amount of heavier oil, gravity about 37" A.P.I., with characteristics similar to the oil produced from the Second Pay. A well was started somewhat down-structure from the deep test to better determine the oil-producing possibilities of the Fourth Pay. Some refinements in drilling technique were adopted during the year. All wells started to the Second Pay were drilled with rotary from the surface. The top 1500 ft. of porous limestone section, formerly drilled with cable tools, is now drilled with rotary without circulation, using water to wash the cuttings into cavities. The shale section from this point to the top of the oil horizons is drilled with natural mud circulation. The productive horizons are drilled with oil circulation under pressure control. A second satisfactory method of completing wells was developed when the two Third Pay test wells were plugged back and gun-perforated through cemented casing opposite the Second Pay, with good results.

Jan 1, 1938