Search Documents

By Vincent A. Scovazzo

"The most significant study on the effects of longwall mining on gas and oil well integrity was completed by a consortium of coal and shale gas industry participants. A field study was conducted in 2013 and 2014 and is referred to by its location on Well Pad NV-35. The experiment site was located at the CONSOL Enlow Fork Mine in Washington County, Pennsylvania.The experiment was completed to verify John T. Boyd Company (BOYD) calculations and studies completed under contract by for the Pennsylvania Department of Environmental Protection Gas Well Pillar Study Update. The findings of the original study were presented by BOYD at the 32nd Conference, while numerical analysis of the Well Pad NV-35 field study was presented by Dr. Su at the 35th Conference.This paper addresses the findings of the experiment and how it confirmed the conclusions of the original study.INTRODUCTIONA field study was conducted in 2013 and 2014 by a consortium of coal and shale gas industry members to test the effects of longwall-induced ground movement on the stability and integrity of wells drilled through a gateroad abutment pillar. The project was initiated to test initial John T. Boyd Company (BOYD) findings of the Gas Well Pillar Study Update (Scovazzo and Moran, 2014), completed for Pennsylvania Department of Environmental Protection, Bureau of Oil and Gas Management (PDEP). Background and initial findings on this project were presented at the 32nd Conference (Scovazzo and Moran, 2012). The field work and numerical analysis were spearheaded by CONSOL Energy, Inc. (CONSOL) with participation by Chevron, EQT, Noble Energy, Range Resources, Marcellus Shale Coalition, and the Pennsylvania Coal Alliance.Dr. Wen H. Su of CONSOL was the leader of the field experiment with input from the participants. Dr. Su also completed numerical analysis of the results and model casing deformation. Analytical results were presented by Dr. Su at the 35th Conference (Su, 2017)."

Jan 1, 2018

By E J. Sellers, A Cocker

Movement of the fragmented rock mass is an inevitable consequence of open cut blasting. Uncontrolled, unaccounted movement from blasting commonly causes ore loss and dilution from waste mixing. Therefore, the prediction of the post-blast location of both ore and waste is vital in grade control and of direct interest to mining geologists. Direct measurement techniques have matured significantly over the past decade, but their use remains expensive and labour intensive. Access and safety issues are further disincentives to regular movement monitoring. What is needed is a combination of direct measurement to establish baselines and reliable predictive modelling.The W H Bryan Mining and Geology Centre of the University of Queensland has pioneered 3D blast movement modelling using ‘physics engines’ to handle in-flight collisions and predict the final resting place of blasted material. Open cut metalliferous mines are a demanding environment for this style of modelling as they can involve complex geometries and variable buffering, which leads to inconsistent confinement. A version of the model designed to deal with these complexities is under development. A well-controlled field trial was needed to validate this new version.A validation trial was completed at a gold mine in South-East Asia. The aim was to increase throughput by increasing the blast powder factor without losing grade through dilution and mixing with waste. Four blocks were blasted to identify the effect of bench height and face confinement on ore movement, fragmentation and process throughput. The powder factor and blast timing were kept constant. Movement of the broken rock was measured by placing blast movement monitors at known positions in the block and then locating them after the blast. The majority of sensors were recovered, providing a unique insight into blast movement dynamics and generating a substantial data set for model validation.The model (called ‘MetaMove ‘) was calibrated for one blast and applied to investigate the extent of grade loss and possible mitigation strategies. Conventional mining techniques that involved firing across the strike of the orebody, and no post-blast boundary adjustment of the ore/waste boundaries prior to digging, were found to cause up to 44 per cent loss of high-grade ore, depending on the grade distributions. Post-blast adjustment of the ore/waste boundaries can negate this loss. The model indicates that altering timing and ensuring that the block boundaries are well confined can further constrain the movement of ore/waste boundaries. Thus, the model can be successfully applied to minimise grade dilution and limit misclassification of ore as waste whilst using higher powder factors to increase mill throughput. Application of a calibrated model to move ore/waste boundaries prior to digging will enable the production geology team to add significant value to the mining operation.CITATION:Cocker, A and Sellers, E J, 2014. Modelling blast movement for grade control at an open cut gold mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 377–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By G. Pan

A geostatistical approach is proposed for the design of infill drilling programs. The method is consisted of three major steps: developing geological favorability models, delineating mineralization and ore envelopes, and classifying reserves or resources. Geological modeling aims at developing favorable geological zones in which drilling is designed. Modeling mineralization and ore envelopes establishes criteria on potential blocks to be drilled. Top target blocks should be those included within ore envelopes. The framework of resource categories includes five types: probable reserves, indicated reserves, indicated resources, possible resources, and barren. Indicated reserves or resources are the top priority to be drilled for the definition of minable reserves. Possible resources may be considered as targets for further exploration. The algorithms involved in the analysis include indicator favorablity analysis, ordinary kriging, and indicator kriging. A case study presented here involves a gold deposit of Carlin type. The deposit was delineated by a sparse drilling program with 230 feet of average spacing. The infill drilling program designed by the new method suggests a significant reduction on the number of holes from a regular-grid infill drilling pattern.

Jan 1, 1995

n the early days of the Hauraki goldfield (1866 to 1889) almost the only system of ore treatment was wet crushing followed by copper plate amalgamation. A further saving of bullion was in most cases obtained from the tailings by means of pans or berdans. Though this system was not always as efficient as might have been desired it answered fairly well for the bulk of the gold-bearing quartz of the Thames and Coromandel districts, where the gold occurs chiefly in the form of visible particles, and there is not a great deal of silver. It failed, however, with most of the ore found in the Upper Thames or Ohinemuri district, especially in the Karangahake and Waihi portions of the field. In those days the cyanide process was not, and the usual prescription of the mining " expert" was smelting. At Karangahake, many attempts were made to discover a payable method of treatment for the so-called" refractory" ore, but on thewhole with very 'little success, and the district struggled along for a number of years without adding very materially to the production of gold in New Zealand. At Waihi, the Martha Co.'s stamp battery treated by wet crushing and copper plate amalgamation some 18,000 tons from the Martha Reef, worth probablyat least £4 per ton, but the average return was considerably less than £1 per ton, a sum which barely paid working, expenses, and consequently the shareholders were glad...

Jan 1, 1903

By S. Malhotra

Processes for the recovery of manganese contained in low-grade domestic sources are evaluated. Conclusions are based on analysis of literature, technical evaluation and cost analysis. The Nossen Nitric Acid Process, the Sulfuric Dioxide Process rind the Ammonia Leach Process should be developed further as they offer the hunt opportunity for commercialization.

Jan 1, 1984

By Robert G. Lenz

Control of ground water for construction purposes is an everyday occurrence in the U.S. Thousands of pumps are in service at any given time. Most of these applications simply consist of pumping water out of an excavation, generally with the aid of sumps. Modern hydraulic and electric submersible pumps permit these procedures because of their ability to pump solids and take air without losing their prime. These procedures work fine up to a point and permit the contractor to control his ground water problems adequately and at minimal cost. When that point is exceeded, the ground water problems sometimes are compounded. Over-application of open pumping techniques can result in slope failures, cofferdam instability, bottom heaving, boils, loss of ground, damage to adjacent structures and utilities, and assorted other maladys which could and should be avoided. This paper will deal with the options involved in ground water control, a discussion of the unwanted side effects of dewatering, and examples of ground water control projects in various cities around the U.S.

Jan 1, 1988

By A. S. Gendron

A brief description of Inco's ORC copper refinery tankhouse and the electrowinning tankhouse is followed by a comparison of the requirements for the production of the high-quality copper in both systems. The description will focus on both tankhouses, with emphasis on experience to date in the electrowinning tankhouse. Particular attention will be paid to sensitivities of each tankhouse to process upsets which can. significantly afject the quality of the product cathodes.

Jan 1, 1977

By S. L. Lebo, J. D. Gargulak

Lignin, the second most abundant natural polymer and bi-product of the pulp and paper industry, has been commercially available in a number of forms since 1940. This growing industry is fueled by demand in traditional applications. Reagents that offer unique solutions in various mineral process applications are examples of advanced uses that also fuel growth. These applications include flotation reagents in fluorspar, bastnäsite and potash, as well as in the zinc pressure leach process. Due to the fact that no concerted effort has been made to find applications for modified lignosulfonates, it is quite possible that this natural material will find use in other benefication processes.

Jan 1, 2002

By W T. Yen

Pyrrhotite crystallises as either a hexagonal or monoclinic structure, both of which can occur in ore deposits. In general, pyrrhotite is not considered as a valuable mineral unless it contains considerable amounts of other metals like nickel or copper. In fact it causes numerous problems in flotation including intensive oxygen consumption, which results in poor selectivity among sulphide minerals in the processing of complex sulphide ores. Also, because of its high sulphur content, pyrrhotite is a major contributor to environmentally detrimental sulphur dioxide (SO2) emissions from smelters. Pyrrhotite also interacts galvanically with grinding media via electrolyte species present in the flotation pulp, resulting in media corrosion. The most effective way to reject pyrrhotite is through a separation stage, which may be difficult when both types of pyrrhotite are present in the ore. In this regard depression of pyrrhotite through a flotation stage may be applied. Pyrrhotite depression by either intensive oxidation or by using sodium cyanide has been practiced. Results present in this work show that NaCN can depress pyrrhotite effectively when combined with an alkaline environment and low collector concentrations.

Jan 1, 2002

By E. H. Crabtree

This paper, describing the milling practices at the White Bird concentrator, Picher, Okla., is one of a series on milling practices being published by the Bureau of Mines. The concentrator of the White Bird mine, Canam Metals Corporation, is located in almost the geographical center of the present Picher mining cam' in the Tri-State district, one-half mile east of the town of Picher, 1 mile south of the Kansas State line, and about 18 miles west of the Missouri State line.

Jan 1, 1930

By Robert A. Clifton

This Bureau of Mines report discusses the mineralogy of zeolites, the properties that make them commercially valuable, the conditions of formation of both natural and synthetic zeolites, and present and potential markets.

Jan 1, 1987

By T. E. Leontis

The specific effect of various rare-earth metals on the room- and elevated-temperature properties of magnesium has been evaluated. Alloys containing didymium exhibit the highest tensile and compressive strengths at room and elevated temperatures. All the rare-earth metals increase the creep resistance of extruded magnesium at temperatures in the range of 400° to 600°F, but the degree of enhancement depends on the temperature and on the concentration of the added metal. THE effects of rare-earth metals on the properties of sand-cast magnesium were discussed in some detail in earlier paper by the author.' The present paper deals with the effect of the same alloying elements on the properties of extruded magnesium. This investigation also had as its aim the development of a wrought alloy having a better combination of room-temperature strength and ductility and elevated-temperature strength and creep resistance than is found in magnesium-Mischmetal-manganese alloys, which have been reported earlier.2-5 The only known attempt to study wrought magnesium alloys containing pure cerium instead of Mischmetal was made by Mellor and Ridley.6 They found that in the form of rolled bars there is a definite, optimum cerium content for creep resistance at 200 °C and that the creep resistance of these alloys at 200 °C is significantly Improved by heat treatment at 550" to 580"C. In the present investigation the compositional variation in mechanical properties of the following alloy systems is presented: I—magnesium-Misch-metal. 2—magnesium-cerium-free Mischmetal. 3— magnesium-didymium. 4—magnesium-cerium. 5— magnesium-lanthanum. Alloys containing predominately praseodymium are not included in this series because of the lack of this material. Experimental Procedures The alloying ingredients used in preparing the alloys described herein are the same as those reported in the earlier paper.' Cerium-free Mischmetal is the rare-earth mixture remaining when the cerium is removed from Mischmetal, which contains all the rare-earth metals as they occur naturally in mon-azite sand, the ore from which Mischmetal is produced. Removal of both cerium and lanthanum from Mischmetal leaves what is commonly called "didym-ium," consisting predominantly of neodymium and praseodymium. Although the composition of the particular batch of each metal used may differ somewhat from the analysis presented previously, these differences are not great enough to warrant repeat- ing the specific composition of each material. The electrolytic magnesium used as the starting material in these alloys has the same typical analysis as that given in the earlier paper.' The alloys were prepared in small laboratory melts applying all the necessary precautions for alloying rare-earth metals with magnesium described by Marande.' Most melts were large enough to cast one 3 in. diam billet 10 in. long. In a few cases, particularly the didymium-containing alloys, the lack of sufficient amounts of the rare-earth metal limited the size of the billet to 6 to 8 in. All billets were scalped to a diameter of 2 15/16 in. and faced to a length of 9 ¼ in. as limited by the size of the extrusion container. The alloys were extruded into ½ in. diam rod on a 500-ton direct-extrusion press using a 3 in. container. The details of the extrusion step are: billet preheat, 925°F (2 hr); container temperature, 900°F; die temperature, 900°F; extrusion speed, 10 ft per min; reduction ratio, 36:1; and percent reduction, 97.3. The lower melting point of alloys containing didymium' necessitated reduction of the extrusion speed to 5 ft per min in order to prevent hot shorting during extrusion. Adequate lengths were cropped from both ends of each extruded rod to assure that all the material used for tests was extruded under uniform conditions. Tensile and compressive properties at room temperature are reported in the several conditions of heat treatment. The ASTM designations are used to distinguish these conditions as follows: T5—Direct age at 400°F (16 hr) T4—Heat treat at 950°F (4 hr) for alloys containing didymium T4—Heat treat at 1050°F (4 hr) for all other alloys T6—T4 + age at 400 °F (16 hr) The lower heat-treating temperature for alloys containing didymium is necessitated by the lower melting point of these alloys. All heat treatments were conducted in electrically heated, circulating-air furnaces. A protective atmosphere containing 0.5 to 1.0 pct sulphur dioxide was used for the high temperature heat treatments. Tension and creep specimens 6 Yz in. long and compression specimens 1½ in. long were cut from the extruded rod. A reduced section of ? in. diam was machined on the tension specimens, whereas on the creep specimens a reduced section of 0.450 in. diam

Jan 1, 1952

By J. M. Mutmansky, C. Lee

"Measurement of the size and elemental characteristics was performed on airborne coal mine dust samples collected by multi-stage cascade impactors as well as channel samples of the geologic materials. Size distributions were obtained using precise weighing techniques on the impactor substrates. Elemental analysis on the samples was performed by the proton-induced x-ray emission (PIXE) method, a rapid and non-destructive method of multi-element analysis.The various analyses were performed on 9 major and 21 trace elements. The results indicate the importance of intake air and shuttle car movements as sources of dust. The association of coal dust characteristics with channel samples was investigated using the coefficient of proportional similarity as a statistical measure. Results show a strong relationship between major elements and the geologic material being cut but a similar relationship between trace elements and geologic materials is not consistent.1. INTRODUCTIONThe most significant occupational disease in the coal industry is known ·as coal workers' pneumoconiosis (CW'P). While CW'P has existed for centuries, its mechanism of occurrence and association with coal dust has been well understood for only a few decades. In the 1930s, the significance of this disease led state and government officials in the USA to perform extensive epidemiological and environmental studies in the major coalfields. Study of these results plus later studies in the coal producing countries of Europe eventually led to the dust regulations that appear in the Federal Coal Mine Health and Safety Act of 1969.The impacts of the 1969 act were a productivity decline and increased production cost. Many analysts attributed this in large part to difficulties in complying with the new dust standards (Brezovic 1981). However, compliance was met in most continuous miner sections rather quickly. The remaining problem area is that of longwall mining where the procedures and layout of the minin~ system make it difficult to meet the standards."

Jan 1, 1989

By Fred Leonard

This report is principally concerned with the engineering and economic feasibility of area surface coal mining systems other than draglines. This analysis evaluates shovel/ trucks, shovel/crusher/conveyors, and shovel/rail excavation and haulage systems for an assortment of geologic environments and production rates in the Powder River Basin (PRB). Shovel/trucks, front-end loaders trucks, and shovel/crusher/conveyors were studied in a multi-seam, dipping geologic area of the Four Corners Region. The Texas lignite engineering and economic research involved bucket-wheel excavators (BWE), BWE/backhoes, and scraper/backhoe combinations for overburden and coal excavation. The PRB truck/shovel study utilized the most recent computer simulation available in both the design and cost analyses. Detailed engineering analysis, followed by in-depth operating costs (operating and depreciation), result in a complete evaluation of each mining system. Cost comparisons of the different mining systems under similar geologic and production constraints are presented in the report to illustrate the estimated capital investment and production costs per ton of coal and bank cubic yard of overburden.

Jan 1, 1980

By Muhammet Mustafa Kahraman

Despite technological advancements and organizational adjustments, lost time accidents are major issues in occupational safety. However, there is very limited work that focuses on variables influencing days lost as a result of occupational accidents. In this study, decision tree and artificial neural network methods were used as machine learning techniques to investigate the impact of factors on accident lost day duration. Degree of injury, worker age, and worker activity were found to be the top three variables impacting loss of time from work. It was also identified that the mining method, location, and nature of injury had a moderate influence on duration lost due to occupational accidents. However, worker experience and ore type did not have any significant impact on the duration, which is an unexpected result. These results confirmed that some accident factors that might have a large influence on the number of mine accidents can be less critical when it comes to accident lost day duration.

Feb 3, 2021

By Frank C. Morris

It is generally recognized that the productivity and ultimate recovery of an oil well may be reduced as a result of reduction in permeability of the sand at the well bore by invasion of filtrates and clay particles from drilling fluids. As a means of determining whether a sand has been "damaged" from these sources, several investigators2 3 4 5/ have developed methods of analysis based on the rate of increase in bottom-hole pressure while a well is shut in. Because of growing recognition of the importance of completion practices as related to the quantity of oil that may be recovered from wells, the Bureau of Mines has studied completion practices in California and the Midcontinent area. Well-interference and pressure-buildup tests were completed Ear seven wells in the Scurry Reef field to determine the effective permeability in the reservoir.6/ Also, a study was made of the pressure-decline curves obtained from 35 water-input wells in 5 different production areas of northeastern Oklahoma and eastern Kansas.7/

Jan 1, 1957

By Oliver Bowles

Marble is one of tile most beautiful and enduring materials employed in the construction industries. Because of its diverse colors, decorative patterns, and varying textures, it has furnished material for artistic architectural design for many centuries. The marble industry is described in some detail in Bureau of Mines Bulletin 106, The Technology of Marble Quarrying, which, unfortunately, is now out of print but may be consul ted at most large libraries. Onyx marble and travertine are discussed in Bureau of Mines Information Circular 6751. The purpose of this paper is to describe the main features of a distinctive group of ornamental marbles known as the serpentine marbles or verde antiques.

Jan 1, 1938

By Terry S. Cory

This report describes the results of a measurement program to determine the broad spectral characteristics of both differential and common mode noise on phone lines in three coal mines; and, signal attenuation spectral characteristics on the same broad basis over phone line strings with taps/branches. The frequency range used was baseband -1000 Hz for resolution bandwidth ranging from 100 Hz near baseband to 30 KHz near I MHz. The signal attenuation measurements were performed on all three "legs" of taps where possible and applicable. Results were obtained comparing shielded and unshielded phone lines In one mine. The results include an improved electromagnetic noise chart for coal mines showing variations with types of mines, topology, and location of noise sources; also, fundamental high-frequency limit on untreated phone lines in coal mines is identified

Jan 1, 1981

By R. H. Grau, S. B. Robertson, R. B. Krog

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. Large-opening mine ventilation is unique for the following reasons: (1) it is challenging to keep airflow velocities high enough to effectively remove or dilute airborne contaminants, (2) large air volumes can be moved through the mines with little static pressure drop, and (3) stoppings to direct ventilation airflows are costly to construct and maintain. The research results suggest that by incorporating ventilation planning into the mine planning process, using propeller fans, developing new stopping materials and construction methods, and using long pillars to eliminate crosscuts where possible, the ventilation of large-opening mines can be significantly improved. The ventilation improvements created by incorporating these various techniques into the ventilation plan will help reduce the exposure of mine workers to airborne contaminants in underground large-opening mines.

By Sarah Ramp, Daniel V. Cacciola, Justin Labrozzi, Shafiq I. Siddiqui, Faisal Ahmed

"Construction of embankments up to 34 ft in height for twelve ramps and roadways needed for the New Jersey Turnpike Interchange 14A project required ground improvement. The subsurface conditions, consisting of up to 30-ft thick layer of highly-compressible peat and organic soils, would induce up to 8 ft of primary and 4 in. of secondary consolidation settlements to the embankments over a long period of time. Innovative ground improvement solutions were needed to meet unique challenges posed by the poor subsurface conditions, space and existing utility constraints, aggressive construction schedule, and massive size of the project. A variety of ground improvement techniques were utilized in six different zones of the embankments to limit settlements and ensure stability of the embankments. These techniques included preloading with surcharge and prefabricated vertical drains (PVD), load balancing using light weight fill, and concrete column rigid inclusions (RI). Additionally, augercast piles with load transfer platform were used under an existing bridge with low vertical clearance. An innovative approach consisting of preloading with surcharge and PVDs followed by installation of RI was needed in one of the six embankment zones with the worst, i.e., very soft, soil conditions. The design of the RI was performed by a specialty ground improvement contractor (SGIC) using Plaxis 2D and 3D softwares. The performance of the ground improvement systems was verified and monitored by load tests and instrumentations. This paper presents details of the ground improvement design, construction, monitoring results, and lessons learned, with a focus on the RI.INTRODUCTIONNew Jersey Turnpike Interchange 14A is located within the cities of Bayonne and Jersey City, in Hudson County, New Jersey. The New Jersey Turnpike Authority (NJTA) identified Interchange 14A as an area of mass congestion in need of redevelopment to improve the increasing demand of traffic and roadway safety. The New Jersey Turnpike Interchange 14A project included the construction of twelve (12) new roadways, in addition to the construction of four new bridges. The limits of construction are shown in Fig. 1.The fill height required to construct the roadway embankments varied from 2 to 34 ft. The proposed embankment side slopes varied from 6H: 1V to 2H: 1V. Additionally, mechanically-stabilized-earth (MSE) walls were utilized to retain the embankment fill along some segments of the roadways. As shown in Table 1, the proposed roadways were divided into six zones, based on location, subsurface condition, and embankment height."

Jan 1, 2017