Search Documents

By R. R. Lowery

An analysis of three 1-1/4-diam manufactured wire ropes of 6x19 classification was done to identify and describe reference conditions of new rope. Reference condition is of value when examining tested or retired ropes. Measurements of strand and rope pitch and of wire and rope diameter confirmed adherence of all ropes to those construction specifications. Mechanical properties of strength and ductility were determined by accepted methods for the ropes and wires from the ropes. Individual wires from one rope failed to meet minimum wire ductility values. Wire chemical composition varied in average carbon levels, from 0.70 to 0.78 wt pct, and in manganese content, from 0.45 to 0.80 wt pct. One manufacturer's product contained 1 to 3 wt pct Ni and Cr. Heavily wrought pearlitic steel microstructures were porous and contained inclusions. Cold work variations were evidenced by wrought grain width. Recorded anomalies reflected the condition of the manu-factured products. The report provides data that compare the three wire ropes studied, but cannot verify the effects that these conditions or anomalies have on rope service life.

Jan 1, 1983

By Joseph J. Wallace

1. The Pittsburgh is the most important bed in Washington County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 4,181 million short tons as of January 1, 1954. Of this total, 4,132 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By E. C. Foster

The project objective of this contract is to design, develop, and demonstrate a dust collecting system for auger head miners, used in coal seams 40 inches or less in height, which will reduce respirable dust below the limits established by the Federal Coal Mine Health and Safety Act of 1969. This system was to be incorporated into 3 Wilcox Mark 20 continuous miner. In order to accomplish this, the objective was divided in three main areas. First: To develop a dust control system which would remove by isolation, respirable dust from the face area and areas where miners work. Second: To develop a dust scrubbing system to remove and collect float dust before the air reaches the return airway. Third: To reduce the overall noise levels to which the miners are exposed.

Jan 1, 1974

By Erle C. Donaldson

Bureau of Mines engineers examined the chemical and biological treatment of sewage water designed in one case for reuse and in another for subsurface injection. In the first case discussed, approximately 6 million gallons per day of sewage are treated by the activated sludge process followed by tertiary treatment that includes ion exchange. The renovated water is used in the industrial complex. Liquid industrial waste is sent to a waste disposal facility where it is treated for injection into a deep subsurface formation. In the second case, a community of 3,000 people is using a lagoon sewage treatment system followed by subsurface injection of t- treated effluent. Subsurface disposal is used to avoid growth of algae and weeds in a nearby lake to which the treated effluent was originally discharged. The renovation of municipal water for reuse provides a source of water for industries in a semiarid region and may also provide a source for domestic use in densely populated regions where domestic water requirements have priority over industry needs. In addition both waste treatment systems provide examples of the use of subsurface waste disposal to avoid pollution of surface streams.

Jan 1, 1971

The ore treatment expansion programme at Mount Isa Mines required the erection of a new lead-zinc concentrator to be known as No. 2 Concentrator. This concentrator was designed by Western-Knapp Engineering Company in conjunction with staff of Mount Isa Mines Limited. Metallurgical design followed conventional wet milling practice, but the size of many plant units is larger than previously used at Mount Isa. The. total capacity of the new plant is 150,000 tons per four weekly period, and the plant is designed to operate in two equal parallel sections.Erection was contracted on a turnkey basis, and the plant was commissioned as a production unit on 23rd June 1966.The existing concentrator, No. I, was converted to treat all copper ore, and the total capacity of the two plants is now 390,000 tons per four weekly period.

Jan 1, 1968

By F. C. Grensing, W. R. Crib

Copper-15 Nickel-8 Tin alloy is a relatively modern material, having been discovered in the 1970’s. It has complexities with casting, hot working and interdependent solid state phase transformations. A key to the high reliability manufacture of wrought rods, bars, plates and tube is the casting technology, which limits segregation, promotes microstructural uniformity and enables hot working. The EquaCast® continuous casting process has enabled the production of a broadening variety of wrought forms with typical yield strengths ranging from 100 to 180 ksi (690 to 1241 MPa) depending on size, shape and temper. This paper reviews the characteristics of wrought Copper-15 Nickel-8 Tin products which have registration in AMS specifications (4596 and 4597) and MMPDS-04 (CN-1) for use in aircraft. The design limits, microstructures, fracture characteristics and tribological behavior will be examined. This alloy system is emerging as a material of choice for aircraft bearings, corrosion resistant oil and gas exploration components, machinery and demanding off-road equipment applications. ToughMet® 3 is an alternative or upgrade to conventional moderate and high strength aluminum bronze bearing alloys.

Jan 1, 2010

By George L. Gates

This report presents is an evaluation by the Federal Bureau of Mines of the effect of clay-water, brine, and oil-base drilling fluids on the productivity of test wells drilled on the Umiat anticline in U.S. Naval Petroleum Reserve No. 4 in northern Alaska. Eleven, wells were drilled on the Umiat structure as part of the U.S. Navy's extensive exploration of the Reserve during 1944-53 to determine the possibilities for oil production. The Federal Geological Survey cooperated in the exploration program and has published a comprehensive report3/ on the geology of the area and case histories of the wells. The re¬port also includes the results of special studies by the Bureau in connection with the drilling and coring of well 9 with oil-base mud in hole and was the source of much of the information used in preparing this publication. Of the eleven wells, four were drilled with rotary tools and water-base mud (one of the water-base muds was an oil-in-water emulsion mud), five were drilled with cable tools with brine in the hole, one was drilled with cable tools with brine in the hole and later reamed with rotary tools and crude oil, and one was drilled with rotary tools and oil-base mud. Although all of the wells penetrated sandstones that contained oil and gas, some were productive and others were not. The latter two wells, one completed with crude oil in the hole (with some added brine) and the other with oil-base mud, had the greatest productive capacities. The wells drilled with cable tools and brine in the hole had lower productive capacities. In contrast, two of three wells completed with rotary methods and fresh-water drilling mud and the well com¬pleted with rotary and emulsion mud were unproductive.

Jan 1, 1960

By Fredrick L. Johnson

Tungsten is the principal mineral commodity in the Laurel-McGee RARE II area; copper and molybdenum would be recovered as by-products with the tungsten. Indicated and inferred tungsten marginal reserves at the Hard Point Mine (fig. l, no. 10) are 16,000 tons (14,000 t) averaging 1.0 percent tungsten trioxide (W03). The mine is outside the RARE II area, but the geologic structure that it is on extends into the area. Indicated subeconomic zinc, silver, copper, and lead resources at the Lucky Strike Prospect (fig. 1, no. 7) are nearly 6,200 tons (5,600 t) averaging 5.45 percent zinc, 0.5 oz silver per ton (19 g/t), 0.40 percent copper, and 0.32 percent lead. Although tungsten has been produced at the Tiptop Mine (fig. 1, no. 12), resources were not calculated because of the spotty nature of the tungsten mineralization. Additional exploration at the Tiptop and Hard Point Mines could reveal significant resources. The potential for tungsten resources at the Payday Prospect, Tungsten Prospect, and Morhardt Mine is also high. The Pine Creek Mine custom mill, located about 35 mi (56 km) southeast, could process tungsten concentrates from the area. Tungsten production has been recorded from three properties, the Hard Point, Morhardt, ant Tiptop Mines. Output was about 405,000 lb (184,000 kg) of W03, nearly all from the Hard Point.

Jan 1, 1983

By Stephen C. Tadolini

The anchorage capacity of four types of bolting systems was investigated in two mines with thick coal roofs. In conjunction with the in-mine tests, a simple axisymmetric finite element computer program was developed. Both the field and computer results indicated that thick coal roofs can be effectively supported entirely by the coal member.

Jan 1, 1986

By Dennis S. Kostick

Salt is a universal mineral commodity used by virtually every person in the world. Although a very common mineral today, at one time, it was considered as precious as gold in certain cultures. This study traces the material flow of salt from its origin through the postconsumer phase of usage. The final disposition of salt in the estimated 14,000 different uses, grouped into several macrocategories, is traced from the dispersive loss of salt into the environment to the ultimate disposal of salt-base products into the waste stream after consumption. The base year for this study is 1990, in which an estimated 196 million short tons of municipal solid waste was discarded by the U.S. population. Approximately three-fourths of domestic salt consumed is released to the environment and unrecovered while about one-fourth is discharged to landfills and incinerators as products derived from salt. Cumulative historical domestic production, trade, and consumption data have been compiled to illustrate the long-term trends within the U.S. salt industry and the cumulative contribution that highway deicing salt has had on the environment.

Jan 1, 1993

By A. Rajoria

A dynamic process model for predicting the fluidized bed roasting of copper concentrates with high arsenic content is presented in this work. Mass and energy balances were performed based on roasting mechanism derived from thermodynamic data of species. The reaction rate data, obtained from pilot plant studies on major reactions, were used in tuning the kinetic parameters of the model. DEAS, a dynamic simulation package, is used in setting up the fluidized bed roaster plant model. The effect of process parameters such as concentrate feed rate, concentrate composition, airflow and cooling water rate on the temperature and conversion of roasting reactions are analyzed. The plant model captures the highly transient conditions occurring during the plant start-up, shutdown and other process perturbations. The application of this model in constructing a virtual plant environment for validating the operating procedures and operator training is presented.

Feb 23, 2014

Development of aggregate resources for use in structural concrete has been encouraged in Japan to support infrastructure improvement and national land conservation. Natural aggregate is a valuable resource necessary for sound economic development, and its importance is growing. After completion of aggregate mining projects, planting and afforestation are implemented. But sandy soil in excavation sites is not optimum for the growth of vegetation, and many years are needed before forests are restored. Planting techniques should be improved to support efficient reforestation in a shorter period of time. For this purpose, problems hampering growth of vegetation must to be solved through application of physical and physicochemical techniques to ensure that the environment and the ecosystem will be conserved in project sites.

Dec 6, 2010

By Ian Martin

A precious metals refinery’s switch to personal computer-based, three-dimensional piping design saved many hours in the design of a South African precious metals refinery. Bateman Minerals and Industrial provided engineering, procurement and construction management services for Impala Platinum Limited-Refineries’ new $60 million refinery in Springs, South Africa. This project is one of the largest platinum refineries in the world. Bateman evaluated a new design method during this project that involved developing a three-dimensional model for the project. The new method saved time by reducing the man-hours required to generate complete project documentation, including plans, sections, isometrics and material takeoffs. The new method also saved design and construction time by allowing designers to detect clashes before construction began.

Jan 1, 2000

By George A. Savanick

The objective of this research is to develop a method for measuring the tensile strength at the interface between minerals in rock. These measurements reflect the strength of the attractive forces operating at crystalline interfaces in rock. Since these forces act in opposition to the forces set up in various rock fragmentation processes, measuring their strength may help in designing more efficient methods of rock fragmentation. The method developed for measuring the strength of intergranular adhesion in rock involves separating a bicrystal from the rock and determining the tensile strength at its solid-solid interface. This technique has been successfully applied to the study of quartz-feldspar interfaces separated from massive pegmatites, graphic granite, and the Rockville granite, yielding average tensile strengths of 5.86, 8.62, and 10.65 meganewtons per meter squared (MN/m2) (850, 1,250, and 1,524 psi, respectively). The data this technique provides indicate that the members of these bicrystals are strongly adherent. Examirtation of bicrystals broken at the crystalline interfaces indicates that the bonds responsible for this adhesion operate over only a portion of the interfacial area. This work conclusively demonstrates that tensile strength tests can be conducted on small selected areas; for example, grain boundaries in rock. The small-scale zones of strength or weakness determined in this way can be related to the overall strength of the rock.

Jan 1, 1972

By Ram V. Ramachandran

As an industry with major potential impacts (both good and bad) on water resources and due to the rising costs of process water, the mining and metallurgical processing industry has a key responsibility to contribute to the overall goal of preserving both the quantity and quality of water available within the watersheds they operate in. As we plan for new and existing mining and metallurgical projects, we need to consider a hierarchy of options to minimize our impact within the watersheds we operate; keeping clean water clean by diverting around our operations; reduction in the amount of water we use; reuse of water wherever possible, and improvements to water quality for recycling and/or release to environment. Technology is needed to treat water to improve its quality for reuse or release to the original watershed. While lime precipitation followed by sulfide polishing is effective for removal of most of the metals, it does little or nothing to remove ammonium ions and anions such as chloride, nitrate, molybdate, arsenate and selenite/selenite. Regulations on sulfate limits in treated discharge water has drawn close attention to the treatment of acid mine drainage (AMD). Management of brine and salt disposal is also posing a problem due to strict regulations and cost of disposal. This paper will: (a) address issues associated with managing water with the objective of maintaining water sheds—status quo-during and after operation (b) discuss potential technologies for advanced water treatment plants.

By K. H. Hofer

La mecánica de rocas se basa en el descubrimiento de las leyes que siguen las perturbaciones del estado natural de la corteza terrestre provocadas por la actividad minera. En ese sentido, el presente texto señala la importancia de este proceso en la ciencia de la minería -en tanto revisa el comportamiento de la resistencia de la roca, determina el estado de las tensiones primarias de la corteza terrestre y analiza la repartición secundaria de tensiones provocadas por la formación de huecos y sus consecuencias sobre la roca en el espacio y tiempo.

Nov 1, 1971

By Richard Goodridge, Stephen Thomsqn, S Rodgers, D Tunaley

The mining, quarry and construction industries are facing’new challenges everyday. These challenges can be imposed by economic objectives or through external factors such as extreme geological conditions. Simultaneously, all mines, quarries and construction sites are facing more and more stringent environmental requirements.

Jan 1, 1998

By I. H. Wong

The large diameter caisson foundations and their construction methods for three 50 to 60 storey high buildings in Singapore are described. The caissons are 5 m to 8 m in diameter and 40 m to 100 m deep, excavated either by hand or mechanised excavators or by drilling and blasting. Performance of the 50 storey DBS Building is described.

Jan 1, 2010

By Jean-François Boulanger

The production of rare earth elements from ore usually consists of three steps; the separation of a concentrate of REE bearing minerals; the cracking of the REE minerals to liberate the REE into an aqueous solution and separation of REE into individual elements. This paper describes the results of laboratory tests conducted on a carbonate-rich REE ore containing bastnaesite and monazite. The tests cover the whole processing sequence of beneficiation, preparation of the REE solution using a caustic leach followed by acid leach to break monazite and bastnaesite and liberate REE into an aqueous solution and the partial separation of the REE using solvent extraction. Details on the product quality and process performances (recovery and impurities removal) are given for each studied step. The paper also discusses the economic advantage of separating the REE rather than producing a mixed REO product to be sold to a refinery for REE separation. A mini-pilot plant version of the process is currently planned.

By Robert L. Lagace

This report describes the results of a system study of the factors influencing mine rescue attempts based on the use of electromagnetic VF rescue transmitters by trapped miners and helicopterborne search receivers by mine rescue personnel. The findings cover four main task areas. The first - mine emergency/disaster considerations - concentrates on characterizing the events and key parameters of mine fires and explosions related to trapped miner location and rescue activities. The parameters include critical time periods, affected areas, survival times, response and rescue times, and survival rates. The second - hardware considerations - concentrates on characterizing the relevant properties of VF rescue transmitters, oxygen-type self-rescuers, VF search receivers, helicopter performance, and signal detectability and sensor sweepwidths for helicopterborne sensors. The third - search theory probabilistic model develops a method to identify the most important regions to be searched, and to allocate helicopter-based search effort so as to maximize the number of miners detected in time to be rescued. The fourth - sensitivity analyses and application of the search model - exercises the search model on representative mine emergency/disaster scenarios to assess the impact and effectiveness of helicopter-based searches. Conclusions and recommendations are presented, together with a set of search scenario planning guidelines.

Jan 1, 1982