Search Documents

By A. F. van Weele

In general cast-in place piles will have an irregular pile shape. However, it is possible that these irregularities are so large that they may lead to pile deficiencies. It is very rarely possible to examine the pile foundations visually. Also the performance of a static or dynamic load test on each individual pile is not practical and much too expensive. This is the reason why pile integrity tests have been developed: to reduce the risk of inadequate pile foundations by performing a simple test. Pile integrity tests are non destructive tests which are carried out after a pile has been installed. Over the years a number of techniques have been developed of which the most important techniques are briefly described in this paper. Of all pile integrity testing methods, Sonic Integrity Testing is the most widely used method in western Europe. This method has been developed by TNO some 15 years ago. Since then the method has been improved, largely due to advances in micro-processing. A major improvement was made by the introduction of digital signal processing techniques. This made the Sonic Integrity Testing method more accurate (smaller defects can be detected), faster (more than 200 piles can be tested on a single working-day) and more reliable (the results are easier to interprete). A few cases will be presented which will show the usefulness of the Sonic Integrity Testing method. In one of these cases, a helpful tool for interpretation of the results is explained: the Sonic Integrity Testing Simulation program TNOWAVE. Notwithstanding the fact that Sonic Integrity Testing is a powerful method, it has also some strict limitations. These will be discussed at the end of the paper.

Jan 1, 1987

By G. Castillo, G. Thies, C. Bissue

"Newmont’s Phoenix mine began gold production in 2006 and has since experienced difficulties in reaching design throughput due to variability in ore hardness. In 2010, a debottlenecking study was conducted, generating multiple options to increase throughput of the existing Phoenix Mill through a series of phased expansions. An option was selected in early 2011 to increase the current concentrator capacity by approximately 25% through two phases. The first phase of the project was the installation of a secondary crushing and screening circuit in order to reduce SAG feed size from a P80 of 6 inches to 2 inches. The second phase focuses on downstream unit operations in the concentrator aiming to relieve existing bottlenecks such as flotation. This paper analyzes the design, commissioning, and operation of a recently installed SAG Pre-crush circuit (Phase 1). The design discussion will focus on concept development, flowsheet design, design criteria, process models, design limitations, and control philosophy. Discussion on the integration of operating data and flowsheet into design during engineering will be presented. Actual operating data of major equipment is gathered from the commissioning and operation of the circuit and compared to the initial design models. Conclusions will be drawn on equipment design factors used during engineering, and the success of model integration into operation. The paper concludes on the successes of the project and where improvements can be made during design.INTRODUCTIONThe Phoenix mine is located within 25 miles of the town of Battle Mountain, Nevada. The mill processes copper, silver, and gold ore. Production started in 2006 and has since struggled to reach the designed tonnage of 33,600 stpd due to the variability in ore hardness. In production year 2010-2011, the Phoenix mill average daily throughput of 33,000 stpd. In 2008, a larger primary crusher (FLS 60/89 gyratory crusher) was installed to operate in parallel with the originally supplied primary crusher (Metso 50/65 gyratory crusher), in order to provide additional capacity upfront in the circuit so that the primary crushing circuit could keep up with the mill.In 2010, a mill debottlenecking study was completed to assess the various options that could be implemented to increase the current mill capacity. The study was completed in late 2010 and contained four tonnages that Phoenix could achieve through various expansion scenarios. A single option was selected in early 2011 to increase the mill capacity from 33,000 stpd to 48,000 stpd. The selected option looked at a four phased expansion that would increase the capacity of the Phoenix mill and address the mill’s current bottlenecks:"

Jan 1, 2013

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

Inhibition of Bubble Coalescence by Salts and Sugars

Sep 13, 2010

Producers with Zero Reportables 2007!: ?New Horizon Mine, Western Fuels Colorado LLC ?Isaacs Run HWM, ICG ADDCAR Systems, LLC ?Savage Mine, Westmoreland Savage Corporation ?South Hallsville No 1 Mine, Sabine Mining Company ?Black Butteand Leucite Hills, Black Butte Coal Company Black Butte and Leucite Hills, Black Butte Coal Company ?Buckskin Mine, Kiewit Mining Group ?Coal Creek Mine, Thunder Basin Coal Company, LLC

Jan 1, 2008

By Randall M. Gennan

Generally sintering is focused on the bonding of particles at high temperatures; possibly with simultaneous densification. However, an important aspect of sintering occurs during heating at relatively low temperatures where polymer processing aids are removed via control of the atmosphere, heating rate, or hold time at intennediate temperatures. New insights into burnout processes show impact from the polymenype, particle size, amount of polymer, atmosphere, part geometry, and thermal profile. This presentation focuses on the key parameters to demonstrate improved mechanical property levels are available in traditional powder metallurgy alloys by proper selection of the processing polymer and proper care in its thermal extraction. The focus is on mechanical property, where gains up to 40% are demonstrated due 10 changes in the processing polymer. Further, atmosphere control during polymer burnout provides a benefit by allowing formation of desirable carbonitrides, giving strength levels over 3 GPa (over 400 kpsi). Insight is? gleaned from powder injection molding, where high polymer contents mandate proper processing control.

Jan 1, 1996

By L. Ou

This paper reports on research on leaching pyrite in a germ-free system. The effects of mineral particle size, pulp potential and various oxidation agents on pyrite leaching were studied. The results indicated that a smaller mineral particle size leads to a higher leaching rate of pyrite. The optimum results were obtained with a mineral particle size of -0.037 mm. The pulp potential reflected the leaching process and an increasing pulp potential improved pyrite leaching. The leaching rate rapidly increased with the addition of oxidation agents such as Fe3+ and H2O2. However, the precipitate generated by ferric ion coated the surface of the pyrite and prevented further leaching.

Jan 1, 2007

By H. Sevim

In this paper, the research effort in simulating the operation of underground coarse-coal hydrotransport systems (UCCHS) is summarized. The equipment of the system to be simulated is already optimally selected by using an analytical optimization model. The purpose of the simulation model is to test the performance of the system and to obtain the distribution of the operating parameters such as water and power consumption, amount of slurry delivered to the preparation plant, etc. Knowledge of the distribution of these parameters is essential for the efficiency of the design and the operation of the system.

Jan 1, 1985

By Y. Miron

Previous studies at the Bureau of Mines outlined the hazards of ammonium nitrate-fuel oil (AN-FO) mixtures in the presence of pyrite-bearing ores. The recent trend in the mining industry to strengthen AN-FO by the addition of aluminum metal raised the question regarding the effect of aluminum in AN-FO in the presence of pyrite-bearing ore. Laboratory work, similar to that done previously, demonstrated that the temperature of a self-sustaining reaction in the presence of AN-FO ore-aluminum is not lower than that for a comparable AN-FO-ore mixture. However, as might be expected from known thermochemical data, once initiated, the resulting reactions between AN-FO, aluminum, and pyrite are much more vigorous than those observed for AN-FO and pyrites alone. The temperature required to produce a self-sustained reaction for the combinations tested in this study is 250°±20° F while in the previous Bureau study, reactions were noted, in some instances, at 150° F. The different pyritic ores may be the cause of this variation.

Jan 1, 1976

By Donald E. Ralston

The Huntsville study area in northeastern Alabama consists of Jackson, Limestone, Madison, and Marshall Counties. Major emphasis was placed on the Huntsville urban area in Madison County to analyze the relationship of urban growth and the minerals industry. Huntsville was delineated into its component urban, suburban, and rural parts for 1964, and the primary area of growth was predicted for 1990. Population estimates were made for the four-county area as a unit and Madison County separately, and projected to 1990. Demand estimates for crushed stone and sand and gravel were made for the same area units and projected to 1990. Analysis of quarry sites in the Huntsville area was made for the present and for the future. The mineral operations of the study area are all located in rural areas; in the case of Huntsville, the mineral sites are located in areas defined as "rural" in the component urban-suburban-rural system. The operations outside Madison County can expect to have minor problems with urban encroachment, while those operations in Madison County can expect major problems associated with urban growth and development. Some of the problems associated with limes tone production can be reduced if producers invest in capital equipment that will reduce the nuisances inherent in this activity. Although urban expansion endangers some quarry operations in Huntsville, topographic and political restrictions which prevent urban expansion can effectively shield quarry operations for some time.

Jan 1, 1970

By Patricia J. Leonard - Mayer

A Bureau of Mines surface resistivity method has been used to determine the joint strike and coefficient of anisotropy of jointed , nearsurface formations at five study areas . The field studies demonstrate the use of rotated , or azimuthal , Wenner-Lee arrays for determining the strike of predominant joint sets . The results of the field studies include the following : in a formation having a predominant , vertical joint set , the maximum value of the apparent resistivity ( pa ) occurs in the same direction ( azimuth ) as the joint strike ; the polar coordinate graph of pa for such a formation is approximately elliptical ; the coefficient of anisotropy ( ^ ) can be calculated from the field data , and values of λ for jointed formations are in the same range of values reported for layered formations ; values of λ are higher at mined sites than at unmined sites . The azimuthal resistivity method and horizontal profiling were used at a site in Pennsylvania to delineate a zone of intensely jointed and fractured bedrock that provided a flow path from a surface stream to a mine . Analysis of the data has been based on a simple model of a jointed formation having a single joint set ; the success achieved to date indicates the need for a more complex model and additional field data .

Jan 1, 1983

By J. Brune, P. J. Coleman, L. Martini

Research in the field of mining safety and health in the United States plays an important part in protecting the lives of miners. The National Institute for Occupational Safety and Health (NIOSH) Mining Program conducts surveillance, studies and developmental work aimed at improving the safety and health of miners. With recent reviews of the Mining Program by the National Academy of Sciences and the Mining Program response (NIOSH, 2008), the importance of setting goals, conducting high quality engineering and scientific research and evaluating the outputs, outcomes, relevance and impacts of these projects has been reemphasized. Surveillance of reported injuries is a first step in deciding on research directions and in designing specific projects. Groups of injuries often share features and attributes that suggest common causes and may respond to similar preventive efforts. Identifying groups of injuries also serves to prioritize intervention efforts. The Mine Safety and Health Administration (MSHA) Accident and Injury database (MSHA, 2008) provides individual case reports of mining injuries, illnesses and certain no-injury accidents (events such as roof falls that stop mine production or miners’ activities for more than one hour). This database is an indispensable resource for researchers and stakeholders needing information on the statistics of these events. From an epidemiological perspective, research projects target groups of miners at risk due to specific patterns of work, equipment, mine settings and the management of safety and health in their mines. Incidence rates are provided by the MSHA data for selected variables, such as surface/underground location, standard industrial classification and state. While incidence rates are the preferred measure for all variables, denominators are not typically available; for example, to more clearly understand the data about injury by occupational type, it would be necessary to conduct demographic surveys. A current survey of the demographics of the mining industry should be complete by 2010, which will allow incidence rates to be developed for a number of variables such as age, occupation and experience. This survey will provide the first update of its kind since the first survey was conducted in 1985. This report describes an alternative method of analyzing and presenting MSHA data for the purpose of identifying high-cost, high-severity injuries and illnesses. Researchers at the NIOSH Spokane Research Laboratory (SRL) developed programs to find the top five most frequent accident classes, natures of injury, types of accidents and other selected variables from the MSHA database. Studying these variables gives a cross-sectional snapshot of the most frequent groups of injuries within a commodity, regional group or time period, and allows researchers to quickly understand developing patterns for new research projects. The primary benefit of this approach is to

Jan 1, 2009

By Y. L. Su

Deterministic and stochastic simulation were combined to develop a computer model of an open pit mining system using bucket wheel excavators and related materials handling equipment. The model is closed and dynamic in the sense that information is fed back to control activities at various levels and reservoirs. The results of interaction between unit operations in one time interval determines overall system behavior for the next interval. Equipment performance curves and system profile characteristics rather than time studies are applied to determine the operation of each activity at any time period. For that part of system where performance is dictated by a random variable~ subjective probabilities are employed. Two stages of research were considered to formulate this model. Stage one involved the formulation of equipment sub-assemblies for the sequence of equipment moves along with related assignments and routines for information retrieval. The second stage of research combined all sub-assemblies into an integrated open pit mining simulator. The model is not tailored for any specific open pit operation but is readily adaptable to any system of surface mining including operations having a high degree of complexity. Questions answered by the model include: 1) system design and selection of equipment for a new mining operation; 2) analysis of existing operations for possible changes, additions or general

Jan 1, 1971

By S. Y. Ezz, K. El•Guindi

A vertical tube, 8 m long and 2.5 cm in diameter, electrically heated to 650°C throughout the majority of its height, was used to study the-effect of ore feed rate and hydrogen flow rate on the reduction of fine iron ore particles. A correlation could be obtained between the combined effect of the amount of reducing gas and reduction time and the per-cent reduction. The results suggest that a method based on the reduction of fine iron ores while falling through up-streaming hydrogen cannot be recommended for industrial application.

Jan 1, 1969

By Fathi Habashi

"Hydrochloric acid (HCl), although more expensive than sulfuric, find uses as a leaching agent in reactions involving iron oxide. The reason for this substitution was the discovery that oxyhydrolysis of ferrous chloride by which HCl can be recycled economically. This avoided the pollution of the environment by ferrous sulfate. It was found further that the rate of leaching of sulfides is faster when HCl is used as compared with sulfuric apparently due to the formation of aqueous chlorine. In case of refractory gold ores, HCl leaching under pressure avoids the use of cyanide solution since gold chloride is produced which can be recovered by standard methods. Hydrochloric acid find also uses in the leaching of scheelite and apatite but its use in leaching clay and anorthosite is questionable.INTRODUCTION Sulfuric acid is the cheapest acid and is used as a leaching agent in many hydrometallurgical processes. However, hydrochloric acid (HCl), although more expensive since it is prepared by reaction of sulfuric with sodium chloride, has replaced sulfuric acid in many reactions involving iron oxide. It replaced sulfuric acid for the first time in 1960s in pickling of steel because of pollution problems (Habashi, 2000). Ferrous chloride produced in pickling can be economically decomposed to ferric oxide and HCl according to:2FeCl2 + 2H2O + 1/2O2 ? Fe2O3 + 4HCl (1)which also shows that the acid can be regenerated but ferrous sulfate cannot be economically decomposed to recover sulfuric acid for recycle. Since then, HCl has been used in many leaching processes. Hydrochloric acid is a corrosive acid and is usually handled in rubber-lined equipment. REGENERATION OF HYDROCHLORIC ACID Regeneration of HCl is conducted in fluidized bed or in spray roaster Fluidized bed oxyhydrolysis In a fluidized bed, ferrous chloride solution is introduced onto a bed of hot ferric oxide where heating is provided by the hot fluidizing combustion gases (Figure 1). The solution is fed on top of the bed of oxides. The liquid feed wets the outer layer of the hot oxide particles and is quickly evaporated to form a layer of new solid oxide on top of the existing oxide, thereby producing dense homogeneous particles."

Jan 1, 2017

By Carl Belser

This report on tungsten in Ouray, San Juan, and San Miguel Counties, Colo., is one of a series describing results of studies on the tungsten potentialities in Region III, Bureau of Mines. The San Juan tungsten deposits occur in an area of 250 square miles, centering near the common corner of Ouray, San Juan, and San Miguel Counties (fig. 1). Field work supporting these studies was done in May 1954. Bureau of Mines reports prepared from investigations made during World War II and under the Defense Production Act of 1950 were reviewed.

Jan 1, 1956

By H. S. Auvil

[Coals of low-volatile rank cannot be coked without admixing large proportions of high-volatile cod in the used type of byproduct-coke oven, because they expend excessively and. exert side thrust, which ruins the oven wells. Some medium-volatile coals also give trouble. Since high-rank coals produce a strong, blocky coke, it is desirable to have the rank as high as practicable, particularly in the manufacture of foundry coke. Accordingly, it has become the practice to mix or blend high-volatile shrinking coals with as much low-volatile coal as possible and still have a mixture that mill not deform the walls or cause difficulty in pushing the coke. Occasionally, the safe limit of low-volatile cool has been exceeded and ovens have been damaged. It is desirable, therefore, to have a reliable method of determining the expending tendencies of mixtures before they are charged into the ovens. Furthermore, coal changes somewhat in its properties as mining progresses, end therefore, mixtures found to be safe at one time may cease to be so subsequently, particularly if nearly the maximum allowable percentage of low-volatile coal is being used. ]

Jan 1, 1938

In this paper, uniaxial compression tests were conducted on intact rocks and broken rocks that were reinforced by grouting, and the effects of grouting on the strength of broken rocks were analyzed. The results show that after grouting reinforcement, the bearing capacity of broken rocks with different lithologies increased, and their uniaxial compressive strength recovered by approximately 6%–16%. The results indicated that the stronger the rock, the smaller the strength recovery of the consolidated body formed after grouting. At the same time, using borehole camera observation and deep overburden strata separations, the fracture development characteristics of surrounding rocks of the gob-side retained entry were analyzed and divided into different regions. On this basis, a guided grouting method was proposed; that is, shallow hole grouting was first used in the plastic zone of the broken surrounding rocks to form the isolation layer, and then deep grouting holes were arranged in the elastic-plastic zone of the transition zone to guide the slurry flow to the shallow unfilled zone. Therefore, the broken surrounding rocks were reinforced into an integrated body and selfbearing capacity improved.

Jul 28, 2020

By Merete Tangstad, Kai Tang

The primary aim of the present investigation is to develop a model which permits to calculate/predict the viscosities of ferromanganese slags, typically focus on the MnO-SiO2-Al2O3-CaO-MgO-FeO multicomponent system. The present viscosity model emphasizes the ability of prediction, i.e. using the binary parameters to extrapolate the viscosities in ternary and higher order systems. To this end, a physical sound model is essential. Temperature dependence of viscosity is described by the Eyring?s formalism. The well-known cell model is used to define the SiO44- tetrahedra in the silicate melts. Composition dependence is expressed in term of viscous activation energy, which is characterized by the binary structural units. The viscosities in ternary and higher order systems are hence predicted using the binary activation parameters. The model has been used to calculate the viscosities in the whole liquid composition range of ferromanganese slag.

Jan 1, 2007

By Dale S. Preece

"The computer program DMC (Distinct Motion Code) [Taylor and Preece, 1989a] was developed in 1988 and 1989 to predict the motion of rock following a conventional blast. DMC executes very efficiently on a CRAY type computer due to the high degree of vectorization and also due to the use of spherical elements [TayIor and Preece, 1989b]. Bulking mechanisms developed specifically for use with spherical elements include rotation-induced dilatation and aspect ratio > 1.0 [Preece and Taylor, 19901. Rotation-induced dilatation allows the radius of the sphere to expand as a function ofsphere rotation to simulate the interaction of corners and sides of blocky rocks. An aspect ratio > 1.0 is achieved by kinematically tieing spheres together."

Jan 1, 1991