Search Documents

By J. P. Morris

A diphenyl ether calorimeter for measuring high-temperature heat contents of ferrous alloys and iron-and steelmaking slags was constructed and calibrated with specimens of molybdenum, alumina, and platinum that were heated to temperatures ranging from 1,720° to 1,875° K. The standard deviation of the calibration measurements was 0.37 percent. By measurements of the enthalpy of delta and liquid iron, the heat of fusion of iron was found to be 3,298 ±100 cal per mole.

Jan 1, 1966

By V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pet natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pet of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 11 a in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F.

Jan 1, 1949

Professor Skeats said: I wish at the ,outset to express my appreciation of the h0!-l0ur conferred on me by my election as President of this Institute for the ensuing year. The selection of a geologist for this position by a body of mining engineers andmetallurgists may be taken as an indication of the recognition that the subject is one which may play a useful part in the great metal industry. Among the records of primitive man the finding of implements of bronze and of iron indicated one of the important, advances made in human civilization, and shows that...

Jan 1, 1924

By James A. Schneider

Selection of resistance factors within Load and Resistance Factor Design (LRFD) requires accurate assessment of uncertainty and bias in load and resistance. To date, many studies have focused predominantly on the assessment of uncertainty, while the potential for bias appears to be the dominant factor in design for consistent levels of reliability under a variety of situations. Bias comes from factors which have been ignored in design method development but significantly influence resistance when extrapolating from conditions typical of databases to those at a given site. Uncertainty and bias can be quantified as the coefficient of variation and mean (or median) of a data set, respectively, for statistical assessment of load and resistance factors. This paper first presents an overview of statistical assessment of resistance factors, and then discusses factors that influence uncertainty and bias when extrapolating to situations outside of conventional databases of driven pile axial capacity.

Jan 1, 2009

According to the Darcy?s law, filtration rate should increase with increasing pressure drop (?P) across a filter cake. In centrifugal filtration, ?P is created by the free water present on the surface of a filter cake. Thus, ?P can become negative when the free water disappears from the cake surface, which makes it difficult to achieve low cake moistures. In the present work, we have developed methods of overcoming this problem by either increasing the air pressure inside or applying vacuum outside a centrifuge. Laboratory dewatering tests conducted using these provisions showed that the moistures of various minerals and coal fines can be reduced to the level that can obviate the need for thermal drying. The new concept has been successfully tested both at pilot- and full-scale, which lead to commercial deployment through Decanter Machine, Inc., under the trade name Centribaric® centrifuge. Keywords: dewatering, hyperbaric centrifuge, pressure drop, Darcy?s law, Centribaric® centrifuge

Sep 1, 2012

By Roger Best

In the mining industry, where some of the vehicles are larger than a one-story house, tire maintenance cannot be accomplished by the tire shop alone. It takes an army of people to maintain a fleet of 100 trucks that may be transporting gold, iron ore, oil sand, copper or coal from an openpit to a refinery and eventually delivering the product to a customer. Everyone working in and around these mammoth machines has a duty to help with the maintenance of the tires, whether they know it or not. These responsibilities comprise observation and reporting hazards up to and including changing out a tire and recording the information in a tire-tracking program such as TreadStat.

Jan 2, 2010

By Erich K. Bender

This report summarizes work performed under Phase I of USBM Contract No. H0366024, Noise Reduction of Jumbo Mounted Percussive Drills. Four drills -Gardner-Denver D93LAR and DH123 and Ingersoll-Rand 0475 and VL120 models were measured at the two manufacturers? test sites; data are given in terms of characteristic noise and vibration levels. A survey of percussive rock drill users is reported. The rationale for the choice of a demonstration drill, the Gardner-Denver DH123, is given and a desired noise reduction goal is established.

Jan 1, 1976

By J. H. Brophy, M. H. Kamdar, J. Wulff

A constitutional diagram for the Ta-W-Re alloy system is presented. Rhenium dissolves in the complete range of solid solutions between tungsten and tantalum up to 48 wt pct in tantalum 'to about 30 wt pct in tungsten. Intermediate x and u phases only are found. X-ray diffraction and fluorescence, metallography and melting-point measurements were employed. THE constitution diagram of ternary alloys of tungsten, tantalum, and rhenium for temperatures above 1000°C is reported in this paper. Alloys in this system rich in tantalum and tungsten are of interest for high-temperature applications, and those rich in rhenium for electronic applications. No ternary phase diagram appears to be available in the literature. The three-component binary diagrams have been previously established1-3 and the present ternary data are consistent with these. EXPERIMENTAL TECHNIQUES Commercially pure tantalum (99.7 pct), rhenium (99.99 pet), and tungsten (99.9 or 99.95 pct) powders were purchased from Fansteel Metallurgical Corp., Chase Brass and Copper Co., and Fansteel or Westinghouse Electric Corp., respectively. These powders were pressed without binder and arc-melted under helium. The preparatory and analytical techniques employed were identical to those used for the Ta-Re system investigation carried out in this laboratory.324 These included X-ray diffraction and metallographic phase identification, X-ray fluorescent and wet chemical analyses, solidus determinations and heat treatments in a resistance-heated tantalum-filament vacuum furnace. For microstructural examinations standard mechanical polishing techniques were used through diamond laps. Polished speciments of all compositions were etched by swabbing with 4 parts HI?, 4 parts HNO3, and 1 part H20. Since the microstruc-tures of alloys containing one or two phases closely resembled their counterparts in the respective binary systems, typical examples are omitted in this presentation. In all the alloys examined, it was possible to observe the number of phases present. Particularly when there were small amounts of one phase involved, it was possible to identify it only by a combined conclusion based on X-ray diffraction, position of an alloy in a composition series, and the phase rule. A total of 100 different alloy compositions was arc-melted and studied in the as-cast condition metallographically and by X-ray diffraction. Specimens of each of these compositions were heat-treated at 2680, 2530, and 2020°C for 1, 2, and 4 hr, respectively. Those which were treated at 2020 were given a preliminary homogenization treatment at 2500°C for 1 hr. Specimens of 25 alloys were heat-treated at 1200o C for 168 hr. Solidus temperature measurements were made by the detection of incipient melting in eighteen alloy compositions. The metallographic and X-ray diffraction results are summarized in Table I. Graphically, this information appears in the isothermal plots of Figs. 2 and 3. Within the accuracy of the experimental methods, two such plots are sufficient to locate these data, since the results for 1200°C were similar to 2020 and those at 2530 resembled 2680

Jan 1, 1962

By Rudolph Emmel

THE mines operated by the South American Development Co. are located in the Zaruma mining district of southwestern Ecuador. They are near the old mining town of Zaruma, which is the only important city in the canton of the same name. The district is situated in the upper end of a valley lying between two spurs of the Cordillera, one of which may be considered the Coast Range and the other an intermediate range. The mining camp proper, known as Portovelo, and the plant are 2.4 km. south of Zaruma, on the north bank of the Amarillo River, a tributary of the Tumbes River, which flows southwestward through Peru to the Pacific. Portovelo is difficult of access; it is reached from Guayaquil by means of river steamers and muleback. Embarking at Guayaquil, the route is down the Guayas River, across the Jambeli Canal, and up the Santa Rosa River to Santa Rosa, a distance of 177 km. From Santa Rosa, the road or trail follows the Santa Rosa River, then across the summit of the Coast Range into Portovelo, a distance of 74 km.-a two-day trip on muleback. The mining property of the South American Development Co. comprises 297 lode claims and 142 placer claims. The combined lode claims cover an area, roughly rectangular in shape, 9000 m. long from north to south by 4000 m. wide; the northern edge of the rectangle is about 3000 m. north of the central plaza of Zaruma. Mineral lands in Ecuador are held by virtue of an annual tax per claim paid to the central government, no surface rights being included.

Jan 1, 1925

Jan 1, 1984

By R. W. Fedors, S. T. Green, G. R. Adams, C. Manepally, L. B. Browning

This paper provides estimates of large-scale temperature gradients that can be used to support modeling of natural convection and cold-trap processes in thermally perturbed drifts. Temperature influences estimates of the quantity and chemistry of water contacting engineered components (e.g., drip shields and waste packages) in a potential high-level waste repository at Yucca Mountain, Nevada. Temperature gradients drive natural convection and cold-trap processes, which could affect the distribution, quantity, and chemistry of liquid-phase water contacting drip shields (waste packages).The confluence of high temperatures, liquid-phase water, and high chloride may lead to corrosion of drip shields and waste packages. An overview of the evolution of environmental conditions in thermally perturbed drifts is presented to provide a context for the estimates of temperature gradients. A mountain-scale conduction-only model is used to estimate temperature gradients and temperature differences for a drift located at the center of a potential repository. Thermohydrologic models and heat transfer algorithms are used to evaluate the reasonableness of the conduction-only results. Estimates of temperature using an in-drift heat transfer algorithm account for the possibility of drift degradation and formation of a rubble pile on the drip shield. Temperature differences between the center and ends of the drift are estimated to rapidly increase to 80 °C soon after repository closure. That temperature difference decreases over time to 15 °C after 10,000 years. Local temperature gradients are generally estimated to be less than 0.2°C/m, though the gradients can be much larger near changes in lithology and near the end of the drift. The estimates of temperature gradients do not account for intermediate- and small-scale variations, such as those influenced by differences in heat loads between waste packages, intra-layer variations in thermal properties of the surrounding fractured rock, or localized drift degradation.

Jan 1, 2004

By Aniruddha Sengupta, Rana Chattaraj, G. R. Reddy, Raj Banerjee

"Earthquake induced liquefaction in saturated granular soils is an important phenomenon which causes severe damage to life and property. In the present study, dynamically induced liquefaction of saturated Kasai River sand is studied in 1-g shake table to assess its liquefaction potential. In the shake table, the soil was subjected to sinusoidal motions of amplitude 0.35g at a frequency of 2Hz. A numerical model using FLAC 2D (Itasca 2005) was performed to simulate the shaking table tests. Reasonably good agreement between the experimental and the numerical results has been observed. Moreover, wavelet analysis has been conducted to identify the occurrence of liquefaction in sand and to correlate the observations found from the experiments. The nonlinear curves used to represent shear strain dependency of stiffness of the Kasai River sand was obtained from cyclic tri axial tests.INTRODUCTIONThe term Liquefaction is used in conjunction with a variety of phenomena that involve soil deformations due to cyclic disturbance in saturated soil under undrained conditions. The generation of excess pore water pressure is the hallmark of all liquefaction related phenomena and the reduction in the volume or the tendency of cohesionless soil to densify during undrained loading condition as prevails during an earthquake is also well known. Use of shaking table tests to understand liquefaction of soils has been demonstrated by several researchers (Ye et al. 2013; Ha et al. 2011). Mohajeri and Towhata 2003 and Towhata et al. 2006 carried out 1-g shaking table tests on soil models prepared in laminar box to study the rate dependent behavior of liquefied soils. Ueng et al. 2010 used a biaxial laminar shear box mounted on shaking table to study the settlements in saturated clean deposits of sand and related the volumetric strain in liquefied sand to the relative density for various shaking durations and earthquake magnitudes. Maheshwari et al. 2012 reported increase in liquefaction resistance of reinforced sand through shaking table tests and concluded that the type and amount of reinforcement in the soil layer has influence on its liquefaction potential.The objective of the present study is to compare the behavior of dry and saturated Kasai River sand when subjected to seismic shaking. The Kasai River separates two growing cities, Medinipur and Kharagpur in the state of West Bengal in India. A number of road and railway bridges exist over the river connecting the two cities. The area being in Seismic Zone III, that is, a zone with moderate probability of earthquake, it is important to characterize the behavior of the Kasai River sand during a possible earthquake event especially when a number of bridges are existing over it. Small scale laboratory model tests and numerical analyses using a commercial finite difference algorithm called FLAC2D (Itasca 2005) have been utilized to study the difference in behavior of dry and liquefied Kasai River sand during dynamic loading conditions."

Jan 1, 2015

By Seth K. Martin, Tony Nichlany, Alan R. Poeppel, Konstantinos Syngros

"This paper presents a case study on bored pile construction in challenging karst conditions below a supertall building in Kuala Lumpur. Innovative design and construction techniques helped keep the project moving through very difficult and unpredictable geological and drilling conditions. The development encompasses about 12,400 square meters and includes a 77-story tower, a 59-story tower, a five-story podium, and four contiguous basement levels. The site is underlain by a residual soil derived from a siltstone/claystone (the Kenny Hill formation), then limestone bedrock. Subsurface conditions are relatively uniform within the Kenny Hill and highly variable at the limestone surface. Extreme cases included 40-meter-tall underground caverns, 40-meter-tall pinnacles, and a 50-meter-tall underground rock ledge. Local piling practice in Kuala Lumpur involves deriving pile capacity entirely in the Kenny Hill formation to avoid the unpredictable limestone surface. However, the massive tower foundation loads and relatively shallow bedrock required the piles to be socketed in the limestone. The 77-story tower will be supported by 2.0- and 2.2-meter-diameter bored piles 50 to 100+ meters long, socketed in limestone, with working loads between 40 and 70 Meganewtons. Two Osterberg-cell load tests were used to develop a site-specific rock socket skin friction correlation with RQD. Exploratory rock probes were drilled at each pile location to design the rock socket length based on the rock quality and sloping rock conditions. The rock mass was pressure-grouted during each rock probe to improve the rock quality and fill voids in the rock.INTRODUCTIONThe Kuala Lumpur City Centre, home of the Petronas Towers and the world’s deepest foundations, will be the future home of a new supertall tower. The 77-story tower will be supported by a piled-raft foundation that relies on piles terminating in the highly erratic, karstic Kuala Lumpur limestone formation. The high building loads coupled with relatively shallow limestone across the majority of the tower footprint forced the piles to extend into the limestone."

Jan 1, 2016

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopic techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relating their inherent properties to properties such as volatile-matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used commercially.

Jan 1, 1970

A series of stemming confinement tests were conducted at a test site near Vernal, Utah. The purpose of the study was to determine the relative performance of various stemming enhancement “plugs”, stem types and loading configurations. The stemming performance was quantified in terms of: . Stem confinement time . Stem ejection velocity . Ground swell velocity . Ground vibration . Air blast . Crater formation Of primary interest was the performance of a new spherical stemming enhancement plug. The initial findings indicate that the hard plastic spheres improved blast performance when used appropriately. Their ability to improve blast performance is reduced when used in over confined or severely underconfined conditions. The study also evaluated the effects of air decking on stemming confinement and explosive performance.

Jan 1, 2000

By Mohammadreza Khanmohammadi, Kazem Fakharian

"AbstractIn driven piles, the gradual dissipation of excess pore water pressure and consequently the soil setup significantly contribute to increasing the pile capacity with time. The question is risen that how the scale differences affect the stress state variations around the pile shaft and at the pile tip? Would the CPT predictions better correlate with End-Of-Drive (EOD) or Beginning of Restrike (BOR) conditions? On the other hand, are the proposed a and ß parameters for clayey soils mostly predicting the EOD or BOR situation? The main objective of this paper is to back calculate the a and ß parameters from CPT profiles, pile Dynamic Load Tests (DLT) at the EOD and BOR as well as Static Load Tests (SLT) and evaluate how they compare with those suggested in literature. Four precast 400 mm square concrete piles driven in North Azadegan Oilfield in Khuzestan Province were selected for the comparisons. CPT test results were available from the extensive geotechnical investigation at the study site. DLT tests using PDA were carried out at EOD, 1 day and 14-day BOR on all the 4 piles. All the piles were SLT tested as well. The UniCone software was used to estimate the tip and shaft resistances using 4 methods including the Dutch, Eslami & Fellenius, LCPC and Schmertmann. The results indicate that the a-method based on the proposed values in literature has predicted a shaft capacity of 90% of the 14-day BOR. This is while the ß-method has predicted a shaft capacity equivalent to 1-day BOR results only. Therefore, both methods have under-predicted the shaft capacities compared to real capacities measured after the significant soil setup in the study area. Two of the CPT methods have underestimated, one has overestimated and one has matched the estimated 60-day capacity."

Jan 1, 2014

By J Allen, B Oats, S Palaniandy, M Lollback

The Julius Kruttschnitt Mineral Research Centre has conducted an intensive VertiMill® (VTM) survey program at the Cannington mine concentrator as part of the ‘collaborative research in stirred milling technology’ program funded by Metso Minerals. Since 2003, Cannington has progressively added grinding capacity into the circuit through VTMs operating in secondary and regrinding duties. Cannington was one of the first mines to adopt this technology in secondary duty by installing two VTM-1500-WBs as part of a capacity expansion to produce sub-100 µm rougher feed. Subsequently, an additional VTM-800-WB was installed in the lead regrind circuit to prepare sub-20 µm cleaner stage feed.Several surveys were carried out to evaluate the VTM performance over a range of changed conditions. Among the key changes in operating variables were circuit power draw, feed rate and water addition to the bottom of the mill. The average specific energy for secondary duty was 3.7?kWh/t. The lead and zinc regrind mills consume 8.1 and 15.3 kWh/t respectively. Generally, the VTM installations have successfully prepared feed for rougher and cleaner circuits by reducing the top size into the floatable regime with steeper particle size distribution, which has led to enhanced recovery. The survey results show the success of VTM installations in secondary (receiving feed from autogenous circuit) and regrind duties.CITATION:Palaniandy, S, Powell, M S, Hilden, M, Allen, J, Kermanshahi, K, Oats, B and Lollback, M, 2014. VertiMill® performance updates in secondary and regrind duties at Cannington mine, BHP Billiton, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

This report is the 22d in a series summarizing Bureau of Mines research and technologic work on coal and related investigations.2 3/ A summary of work published during 1957 and of work in progress is presented. Details regarding the subjects treated in the publications may be found by referring to articles cited in the footnotes. The objective of the coal work of the Bureau of Mines is to obtain information that will lead to improved production and utilization of coal, thus conserving a most important national asset.4 5/ Though studies of mining methods and exploration of various coalfields ma; contribute directly to improved production, no less so does the work in health and safety. The many problems relating to chemical and physical properties of coal reflect the need for an understanding of these properties for the most effective use of coal in its various fields of application and for the development of new methods of processing coal. Studies of existing and proposed processes of combustion, carbonization, gasification and hydrogenation of coal are necessary for increased efficiency in its use. Engineering service provided by the Bureau is of direct value in the conservation program in preventing waste. Stations where the main coal activities of the Bureau are carried out are shown in the following list:

Jan 1, 1959

By R. V. Higgins

A computer program is presented to calculate the shape factors and volumes of cells from a potentiometric model, using coordinates of the inter-sections of the stream lines and equal potentials and a few additional coordinates. Shape factors are used in flow computations when the geometry is complicated. The program also includes computer instructions to divide the channels into cells of equal volume and to obtain the shape factor for each of these equal volume cells. An illustrated example using the potentiometric model for the waterflood of a seven-spot well-spacing pattern is presented. The information contained in the report is of value not only to those allied to the subject but also to others, because many of the techniques can be conveniently used in formulating other computer programs.

Jan 1, 1966

By Richard D. Hagni

Although the economically important uranium minerals are difficult to recognize under the ore microscope, they can be identified by a combination of qualitative and quantitative techniques. Useful quantitative techniques include indentation hardness, percent reflectance, spectral reflectance curves, and color coordinates. The latter two properties are especially distinctive for the primary urahlferous minerals uraninite, coffinite, brannerlte, and davidite. Together with the quantitative properties of indentation hardness and reflectance, the character and color of internal reflections are distinctive for many of the secondary uranium minerals. Ore microscopic techniques also provide an excellent means for determining the intergrowths of these minerals with other ore and gangue minerals. Such intergrowths are important to an understanding of the genesis of uranium deposits, and they may be important to uranium extractions.

Jan 1, 1981