Search Documents

By J. P. Dunford

This U.S. Bureau of Mines report describes the development of a yielding steel post for underground mine support. The report covers concept development, laboratory tests, modifications, and field evaluations. The objective of this work was to develop a stiff support member capable both of supporting high loads and yielding when excessive amounts of mine entry closure were present. The 6-to 7-ft steel post was designed to yield nearly 2 ft while maintaining a 45-ton (force) load. The post is a three-piece unit consisting of top and bottom telescoping legs and a separate foot bracket. It develops its load-carrying characteristics when the lower pipe, with an attached interference ring, is forced into the larger top pipe. Laboratory tests were used to determine critical loads and post performance for various post lengths. Field tests showed that the posts could perform in actual mining conditions. The post has the ability to provide support in highly yielding ground and also, because of its slender profile, enhance ventilation and provide more area for travelways and escapeways. The design is simple enough to allow for fabrication at most mine shop facilities.

Jan 1, 1989

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By A C. Chieregati, A Heberle, F L. S P Villanova

Since the publications of Gy’s initial work, many authors have discussed the approaches to estimate the variance of the fundamental sampling error (FSE). Experimental tests suggested by Pitard and François-Bongarçon determine the sampling parameters K and a to calibrate Gy’s formula. The heterogeneity test and the sample tree method are well known and broadly used for many commodities. However, prior to the analysis, the collection of a representative sample is an intriguingly difficult task. The composite for the heterogeneity tests often consists of run-?of-?mine material or processed ore on a conveyor belt. In most cases the final sample does not have enough mass, mixes different geological units, represents a rare blend and does not characterise the deposit. In order to obtain a reliable composite for trace elements and low-grade ores, sampling practitioners suggest at least half a ton of material.To prevent the common representative pitfalls in the FSE, this case study focuses on a single gold-?bearing geological unit collected in situ. With this unit being structured by the mine geologists, but with the interaction between engineers and chemists, it was possible to validate the reconciliation suggested by Pitard (2015). The heterogeneity test and the sample tree method were performed using 500 kg of a smoky quartz from a single geological domain and the results were compared to Gy’s formula. The logging practice by the geologists was modified, emphasising the definition of the size of the gold nugget or its cluster, number of grains and association. Finally, a mineralogical study was conducted on the geological unit to define the liberation factor. All the information is compiled in this paper, showing the need to fully understand the mineralisation to correctly define representative samples and proper analytical techniques.CITATION:Villanova, F L S P, Heberle, A and Chieregati, A C, 2017. Heterogeneity tests and core logging – a final reconciliation, in Proceedings Eighth World Conference on Sampling and Blending , pp 107–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Gheorghe Marin, Franco Chiesa, David Levasseur, Bernard Duchesne

Over the past 20 years, pressure die casting has evolved to a point where structural parts can now be produced by this process. This has been made possible by the development of vacuum die casting and by the development of die-castable, low iron content alloys. This resulted in the production of low porosity, weldable die-cast parts on which heat treatment may be applied. In the present paper, the influence porosities on the tensile properties of as-cast A360 tensile test bars was evaluated. This was done by casting 24 clusters, comprising three 6mm diameter test bars each, in a 280T cold chamber pressure die casting machine after a steady dynamic equilibrium had been reached. Modeling of filling allowed to explain the differences in porosity observed in the 3 samples of a same cluster while the results of solidification modeling were related to the microstructure. Tensile samples were radiographed on a real time X-cube apparatus and separated into 2 lots: samples where no porosity defect were visible and samples with visible defects. By measuring the tensile properties of the 2 lots it was possible to quantify the drop in tensile properties brought about by porosity, which is the most common defect observed in pressure die-cast parts.

Jan 1, 2015

By Franco Oboni, Iain G. Bruce

The design of tailings containment structures relies on well-understood engineering methods being applied consistently. Unfortunately, not all facilities are designed or managed to the same level of competency. To standardize procedures, the Mining Association of Canada (MAC, 1998) prepared a “Guide to Tailings Management.” It recommended review of designs and an assessment of the risks associated with tailings impoundments be implemented during all phases of amine life. This paper describes how the quantitative risk assessment (QRA) process can be used to define risks associated with the design, construction and operation of a tailings management facility. And it discusses how, once the risk tolerability curves (RTC) are defined for a project, they can assist the risk management (RM) process.

Jan 1, 2002

By A. Taghavi, I. Hassan, A. Solecki

"The Eglinton Crosstown Light Rail (LRT) Project is part of an $8.4 billion investment to expand transit in the Toronto, Canada area and is the largest transit project initiated in Province’s history. Settlement control and impact to over 1400 adjacent structures due to tunnelling was identified early as a critical project risk. The ground conditions along the 10km tunnel alignment consist of water bearing soft ground deposits (clays, sands, silts) which required careful analysis and control during design and construction. This paper will describe the process used to analyze settlements along the numerous of adjacent structures and evaluate achieved settlement results to those used during design. The paper will demonstrate that with the appropriate design specifications, selection of modernized EPB machines, and contractor performance, settlement can be maintained well below typical industry (volume loss) standards, expanding the application and suitability of soft ground tunnelling in sensitive settlement areas. INTRODUCTION The Eglinton Crosstown Light Rail Transit (LRT) Project is part of an $8.4 billion (2010$ CND) investment from the Ontario provincial government to expand transit in the Toronto, Canada area. The project is being developed by Metrolinx, an agency of the Government of Ontario to provide 19 kilometers of dedicated LRT service connecting the City of Toronto from the west to east along Eglinton Avenue. Upon completion in the year 2020, the Crosstown will be the first LRT constructed in Toronto. It will link regional and local transit, cut travel time along the route by half and provide over a thousand jobs during construction."

Jan 1, 2016

By Henry M. Harris

A study was made by the Bureau of Mines to determine if shapes of oxide-glass compositions could be roll-formed at high temperatures, and to find the conditions required for adequate formability. A unit with directly connect' furnaces and heated rolls that allowed forming of most of the compositions developed. Glasses of the feldspar type were chemically unreactive with the alumina grains, and allowed the best roll forming. Optimum forming was attained at temperatures of 1,400° to 1,530° C, with compositions containing 30 or 40 percent feldspar and 60 or 70 percent alumina. Formability was better when compositions contained minus 325-mesh materials, rather than coarser or finer powders. In many cases, roll-formed shapes had physical properties equal to or better than the normally sintered shapes of the same composition.

Jan 1, 1967

By C. G. Storm

Permissible explosives are those that have passed the tests pre- scribed by the Bureau of Mines for explosives intended for use in coal mines, and are therefore recommended by the bureau as suitable for this class of work when used under the prescribed conditions. The tests for permissible explosives and the conditions prescribed for their use are described in Miners' Circular 6 of the Bureau of Mines. Up to June 1, 1915, 168 explosives had been classed as per- missible explosives; 133 of them were then on the bureau's "per- missible list" and 35 had been withdrawn by the manufacturers. In addition to the required physical tests, each explosive is sub- jected to a complete chemical examination in order that its exact composition may be known and also that the composition of future samples of the same explosive collected in the field may be compared with that of the sample which originally passed the bureau's tests, for by such comparison it may be possible to ascertain whether or not the explosive as supplied to the miner is still "permissible." This bulletin is published primarily for the purpose of informing manufacturers of such explosives as to the methods used by the Bureau of Mines in the analysis of samples received for tests to determine their permissibility. Such information may be of value in cases of possible controversy over the results obtained in the analysis of a field sample as compared with those obtained in ana- lyzing the sample originally tested by the bureau. Also, a descrip- tion of the methods used by the Bureau of Mines in the analysis of explosives should be of assistance to the many chemists engaged in similar analytical work.

Jan 1, 1916

By E. R. Maize

[he scconG rcport of :his st?rI.org 8cdt with o3servatioi:s of conver- gence of roof an4 floor at t!x*re: ?.cc.-.tioris iri til~ ClVucible mine of kke Cru- cib1.o Fuel Co. Data on sl:'ociacnce ?.rd Lztcrcl mwe:~cnt cf the surface were .:lven for two of these areas, a-12 it was mentioned that ~lr~~ilar data were being obtained on a ?art of Pe:sc:rlvtzr.ia Fii~l?trr.y FE:, ~i!lic;l pcser: over the third area. 'I'hie hichw~ :LEO FasseE over t!lc ITenncoli::. :.line of the Bnckeye Coal Co. 9 milcs to ';he so-lth, cnd at P. l~tcr C'..att: ~.nr?r.,cc?r:cntS *.rere mnd.e to make similar observati on3 there. This y: pr mrnmri:.c n Czto obtnino? at those two locetionn,]

Jan 1, 1941

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009

All previous attempts to cut rock in boring by means of revolving steel cutters have failed, chiefly in consequence of the mis-shapen teeth grinding the rock and themselves simultaneously, until, after a very few revolutions, the points of the cutters were so worn that it was impossible to force them into the strata. The diamond drilling plant being cumbrous, complicated, and costly, and seeing that fully 70 per cent of the boring generally needed is in what is known as the" milder strata," it will be readily understood that much of the work done will not pay a dividend on the outlay, so great is the cost of removal, the wear and tear of the machinery, and the loss of diamonds. The Calyx Drill, however, invented by Mr. F. Harley Davis, has been constructed so as to overcome these difficulties, and will penetrate quickly and .at a low cost this 70 per cent. of the milder strata. The Drill has taken ten years' hard work and thought to bring it to its present state of perfection, and it will now drill with steel cutters the 70 per cent of the work performed by the diamond drills at a greater speed and at about one third the cost of the latter.The utility of the diamond drill for certain work is undeniable, but it cannot by any means be described as a machine of general popular usefulness that is to say, it is quite beyond the reach of the great masses of mankind.

By Taylor G. H

The Triassic Ipswich (SE. Queensland) coals are of bituminous rank. The more exact rank of individual samples was determined by measuring the reflectance of the vitrinite. While in general the rank of the coals increases with stratigraphic depth, minor reversals, probably related to igneous intrusions, occur.The Ipswich coals form a coherent group so far as petrographic type is concerned. All are comparatively rich in vitrite and clarite, cutinite being the common maceral of the exinite group. The mineral contents of all the coals are comparatively high, clay and quartz being most abundant. The coals appear to be of essentially autochthonous origin, and to have been formed under conditions of fairly rapid subsidence.While the use of the coals is at present restricted to combustion, most have pronounced coking properties, as would be predicted from their petrographic composition and reflectance. However, the high mineral content of the coals would be a limiting factor in their use for coke-making.INTRODUCTIONDuring the last ten years, the Division of Coal Research, Commonwealth Scientific and Industrial Research Organization has carried out an extensive investigation of Australian coals, providing a wide range of analyses of most of the important of them. Special attention has been given in recent years to Queensland coals.Most seams were sampled as a number of subsections, enabling the internal variations, as well as the overall properties, to be assessed. The lenticularity of many of the mineralrich layers may tend to limit the significance of the samples, particularly in respect of ash yield, but although the vertical distribution of mineral matter may vary considerably from one sampling position to another, the lateral variation of the total mineral matter in the whole seam may not be great.Apart from extensive chemical analyses and utilization...

Jan 1, 1963

By Paul J. Axtell

The results of in-situ geophysical cross-hole tests on improved soil by soil mixing (SM) and jet grouting (JG) are described. This testing was conducted on soil improved by SM and JG columns constructed in the downstream free-field of Tuttle Creek Dam near Manhattan, Kansas as part of the seismic retrofit. Results of similar geophysical testing performed on untreated soil in the vicinity of the Downstream Test Program (DTP) area, as well as beneath the embankment at several locations, are also described and used for comparison purposes. In-situ shear moduli are also compared with those determined in laboratory resonant column tests. The increase in stress wave velocities and associated shear moduli by SM and JG treatment are presented for use in liquefaction potential and seismic deformation analyses of SM or JG treated soil. This data is required to determine the decrease in liquefaction potential and earthquake-induced permanent deformations due to SM or JG with respect to that of untreated soil.

Jan 1, 2008

By W. R. Ingalls

THE following chronology presents the history of lead-mining in the United States in a brief form and is a useful reference in connection with the statistics of production 1621. Lead was mined and smelted near Falling Creek, Va., to supply the local demand for bullets and shot. This was the first mining and smelting of lead in what is now the United States. 1632. In a report made on the minerals of New England, lead-ore is mentioned. (Bishop, I., 470.) 1650. Supposed beginning of mining by Jesuits in Pima county, Ariz. 1651. Grant of lead-mine at Middletown, Conn., to Gov. John Winthrop.

Jan 9, 1907

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By J. E. Hoffman

The operation of the U .S Metals Refining Company, USMR Co. is defined below by the description of a variety of unit processes and operations the author encountered during his tenure with the operation, 1955 - 1978. The operations discussed include: sampling and sweating of radiators, processing of Indian Coin, treatment of insulated wire, baghouse and converter dust treatment, blast furnace and converter operation, the electric arc furnace, antimony control, selenium and tellurium products, electrolyte liberation with soluble anodes, and the precious metals refinery. These operations, although peripheral to the primary copper production circuit, were critical to the company's technological and economic base.

Jan 1, 2000

By Richard E. Thill

The Bureau of Mines' Oil Shale Data- Bank (OSDB) was created in 1976 to serve as a centralized source for the storage, retrieval, and dissemination of technical literature, patents, and information on research projects in oil shale. Thousands of bibliographic references, patents, and research projects relating to the mining of oil shale have been identified, abstracted, and indexed according to selected keyword topics. The resulting data bank listings are contained in three sections, each with a separate keyword breakdown for use in rapidly identifying references pertaining to a specific subject. All references cited in the OSDB were published prior to an established cut-off date of May 1, 1981, when a redirection of Bureau of Mines programs resulted in the loss of project funds and the subsequent phasing-out of data bank operations. ACKNOWLEDGMENTS The oil shale data bank listings are the result of a team effort of the project staff. The contributions of Jimaleen Jansma for keypunching, information acquisition, and data entry, and John Brandenburg and Sandra Brake for keywording and information acquisition are gratefully acknowledged. Appreciation is expressed to the staff members of the Smithsonian Science Information Exchange, Washington D.C. for their cooperation in supplying data on recent research projects in oil shale for inclusion in the OSDB listings. Appreciation is extended also to the staff of the Gallegos Research Group for assisting with computer services to obtain the final printouts and transfer of files onto magnetic tape.

Jan 1, 1982

The role of a project metallurgist is diverse and covers input into the resource definition, mining studies, metallurgical test program development, process engineering and plant design, cost estimate preparation and financial analysis aspects of project feasibility studies. Mining project schedule and cost overruns can often be attributed to cutting short metallurgical test work, engineering and cost estimating leading up to commitment to development. In a significant number of cases this may result from the lack of understanding and commitment by the project proponent to the requisite metallurgical and processing studies required during the various pre-commitment stages of a mining project. Metallurgical test work, process development, engineering and cost estimating requirements for each stage of pre-commitment development are described together with a summary of the ongoing role of the project metallurgist during detailed engineering and commissioning of a process plant.

Jan 1, 2008

By Bowen Li

Andalusite is an excellent raw material for refractory applications due to its high aluminum oxide content and phase transformation to mullite at high temperature. Granular andalusite in particle sizes of about 1 to 2 mm was traditionally utilized for the manufacturing of refractory brick. However, if powder andalusite in micron particle size is utilized in high-alumina refractory products, reinforcement on the refractory brick can be obtained and the sintering temperature can be decreased. The phase transformation of powder andalusite plays a key role for the difference.

Jan 1, 2006

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018