Search Documents

By L. A. Neumeier

The Bureau of Mines evaluated the properties of zinc alloys containing 25 to 40 wt pet Al and 0 to 0.7 pet Mg. Microstructures, hardness, and tensile properties were evaluated for material as extruded at 285° C, solution treated at 300° to 400° C, and subsequently aged at 100° to 200° C. The alloys without magnesium are characterized by low hardness and strength with high tensile elongation and reduction in area. It was verified that magnesium effectively retards the Zn-Al eutectoid transformation below 275° C and markedly increases hardness and strength with decreases in ductility. Solution treating at 350° C results in large grain sizes and gross embrittlement. Subsequent aging of the Zn-Al-Mg alloys at 200° C restores ductility substantially and stabilizes the structures, but strengths are considerably reduced. Combined strength and ductility properties are better for the as-extruded condition than for any heat-treated condition. There is usually little advantage in overall tensile properties from increasing magnesium above 0.1 pct.

Jan 1, 1971

By Mathew Avery, Colby Barrett

In November 2016, a 7.8-magnitude earthquake caused more than 100,000 cubic meters of rock and debris to tumble down and bury the transportation infrastructure below Ohau Point in New Zealand. All routes between the northern and southern portions of South Island were severed. To undertake the rebuilding efforts, the New Zealand government established North Canterbury Transport Infrastructure Recovery (NCTIR) – an alliance to repair the road and rail networks between Picton and Christchurch. NCTIR’s aim was to have the road open by Christmas 2017, but work also continued into 2018 to complete a number of safety improvements along the highway. The presentation will review the initial remediation attempts, the necessity to re-evaluate the original efforts, the need to incorporate techniques that were “outside-the-box” and different from traditional methods, and the logistics and planning that were required to complete the work safely. INTRODUCTION Shortly after midnight on Monday 14th November, a magnitude 7.8 earthquake struck the small South Island settlement of Waiau in North Canterbury, 100km north of Christchurch. The quake was the largest in New Zealand since the magnitude 7.8 Dusky Sound earthquake in 2009 (GNS 2016). While shaking was widespread with over 15,000 recorded ‘felt reports,’ the worst shaking occurred about 50 seconds after the quake rupturing started. The energy of the tremor progressed north over several minutes with surface rupture recorded on a total of 21 faults. The length of all the fault ruptures combined was close to 100km (GNS 2016). The degree of ground shaking was high, recorded as Modified Mercalli Intensity Scale (MMI) Level 8 – Severe. This level of shaking causes considerable damage in ordinary buildings with partial collapse including fall of chimneys, factory stacks, columns, monuments, walls, etc. At a human level, people experience difficulty standing; while furniture and appliances shift. Geologically, the damage depends on the geological setting. In Kaikoura and the surrounding area, especially the coastal highway State Highway 1, north and south of the town, many of the slopes consist of over steepened weathered, fractured greywacke. During the quake, the shaking caused significant and widespread damage with a total of 26 major slips (and many smaller slips); closing both State Highway 1 and the Main North Rail Line between Picton and Christchurch.

Jan 1, 2018

By Glenn A. Shirey

The objective of this contract as to prepare a detailed, readily usable handbook on dust control techniques for longwall mining operations. Information was gathered from available literature, and through contacts with industry and government personnel. The handbook describes those methods of dust control applicable to today's longwall mining systems, and contains sufficient design elements to assist operators with problems in testing or implementing new control procedures. Complete reference lists are presented at the end of each chapter to direct the reader to additional information.

Jan 1, 1985

By R. F. Pilgrim

"This first chapter of the SPOC Manual 1s intended as a general introduction to all the other chapters in which the mineral process evaluation and optimization methodology is presented. This chapter also provides a brief description of available software for mainframe and m1crocomputers and provides information on its distribution by the Technology Information Division. CANMETRESUMECe premier chapitre du manuel SPOC est un guide général qui présente les autres chapitres ou l'on traite de la méthodologie d'évaluation et d'optimisation des procédés miméralurgiques. Le lecteur y trouvera aussi une description sommaire des programmes de calcul développés pour ordinateurs centraux et pour micro-ordinateurs ainsi que la façon de les obtenir de la Division de l'information technologique du CANMETComputer simulation of mineral processes has slowly emerged as an established branch of activity in A&D centres and in several teaching institutions after decades of slow progress. Substantial efforts to develop application software based on years of research on process modelling are being pursued in many countries ( 1 .2,3,4.5). The late BO's should see a flurry of success stones about significant leaps of productivity achieved in several plants through systematic process evaluation and computer simulation studies.In Canada. the SPOC project (Simulated Processrng of Ore and Coal) was initiated at CAN MET in 1980 with the obJective of developing and transferrrng to the mineral rndustry a computer-based methodology for process evaluation and optimization. The proiect deliverables include:- an engineering manual covering most aspects of off-line computer simulation:- a bank of FORTRAN software accessible through data communication lines for user familiarization and distributed at a nominal cost in source form by CANMETThe yearly progress reports of the project contain detailed information on the project elements since 1980 16). The context of SPOC can be summed up by quoting Gordon Agar""s 1975 statement during a workshop on research needs in the mineral industry: ""What is needed is a joint effort between the academic community and one or more enliglitened industrial concerns. The effort will have to be an iterative one with data collection followed by testing the model modification of the model (s), more testing prediction, modification. data collection and so on (7). A few parallel in1- t1atives had been reported in papers or research contract reports (8, 9) but there was an obvious need for CANMET to bridge the gap between the R&D and the production sectors by undertaking a project that would document past applications and induce a new generation of initiatives through the consol1dat1on and transfer of suitable manuals and software. The effort took shape as the CANMET SPOC pro1ect in which methodology transfer was to play a key role (10)."

Jan 1, 1986

By S. Weiss, E. Espinoza

The El Sauzal gold-silver deposit is a high-sulfidation, epithermal precious-metals deposit hosted by an east-dipping sequence of dacitic and rhyolitic pyroclastic and debris-flow units of probable Oligocene age. Total gold production since startup in late 2004 is approximately 450,000 oz. of gold. Above the sulfide boundary gold is mainly disseminated as small grains interstitial to alunite, kaolinite and quartz. The majority of the ore is found in quartz-alunite-kaolinite altered rock that mantles tabular to irregular silicic cores of vuggy, residual quartz ±kaolinite ±dickite. Grade domains are modelled as subhorizontal to east and southeast-dipping. Higher-grade domains cut across alteration zones and also coincide with transitions from vuggy quartz to quartz-alunite-kaolinite. The highest grades are commonly found marginal to vuggy quartz in transitional, hematite-rich quartz-kaolinite and quartz-alunite-kaolinite rock.

Jan 1, 2007

This Bureau of Mines report is a reference manual of procedures used by the Bureau's Twin Cities Mining Research Center for obtaining rock properties. Included in the report are discussions on the usage of each property, descriptions of the general test methods for obtaining the properties, and instructions for performing the tests. The Instructions embrace details of the specimen configuration, test apparatus, test procedure, test conditions, and calculations needed to achieve satisfactory results. Although the procedures presented in this reference manual generally conform to recommendations of the ASTM Administrative Committee on Standards, they are not purported to be standards.

Jan 1, 1974

By Christopher Mark

Dr. Christopher Mark serves as Team Leader of the Rock Mechanics Section in the Rock Safety Engineering Branch of the NIOSH - Pittsburgh Research Laboratory. In this position he leads a multi-disciplinary team and conducts individual research directed towards fundamental ground control safety issues affecting miners. Dr. Mark is recognized as one of the country?s leading authorities on coal mine ground control. Through his research, he has made numerous important contributions to mine safety that have been widely adopted into mining practice. He is a highly original researcher, and has often developed new and innovative methods to tackle extremely complex problems in his field. In recent years Dr. Mark has also achieved wide international recognition. Five research projects in Canada, Australia, and South Africa have been based largely on his work.

Jan 1, 2007

By E Heath, F McDermott, S Turner, P van Calsteren

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath midocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and om, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100 000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50 000 years prior to eruption.

Jan 1, 1995

By R. Cao

Geostatistics was initially developed in the mining sector, but has been extended to other geoscience applications, including forestry, environmental science, soil science, and petroleum science and engineering. This paper presents methods, workflows, and pitfalls in using geostatistics for hydrocarbon resource modelling and evaluation. Examples are presented of indicator variogram analysis of categorical variables, lithofacies modelling by sequential indicator simulation and hierarchical workflow, porosity modelling by kriging and stochastic simulation, collocated cokriging for integrating seismic data, and collocated cosimulation for modelling porosity and permeability relationships. These methods together form a systematic approach that can be effectively used for modelling natural resources.

Jan 1, 2014

By D. Grgic, A. Giraud, F. Homand

RESUME : Le comportement mécanique partiellement saturé du minerai de fer a été étudié à partir d’essais de compression simple sur des éprouvettes à pression capillaire imposée par les solutions salines. Les échantillons restent peu saturés (32 %) même pour une humidité relative de 94 %, du fait de la présence de mésopores. Jusqu’à 90 % d’humidité relative la résistance diminue régulièrement. De 90 % à 94 % une forte chute est observée et pourrait être liée à la fois aux effets capillaires et à l’hydratation de certains minéraux. Le cycle hydrique subit par la roche dans la mine a été modélisé en 1D à l’aide d’un code de calcul entièrement couplé pour les milieux poreux partiellement saturés. Les calculs ont montré notamment une diminution importante en paroi des contraintes totales au cours de la phase de désaturation et une augmentation importante au cours de la phase de resaturation. Ces variations pourraient induire un endommagement du massif et être à l’origine d’instabilités, et soulignent l’intérêt d’une modélisation avec une géométrie plus adaptée. MOTS-CLEFS : mines de fer, partiellement saturé, pression capillaire, résistance, modélisation. ABSTRACT : The partially saturated mechanical behavior of iron ore has been studied from uniaxial compression tests on samples in which the suction is imposed with aqueous solutions. Samples are little saturated (32 %) even for a 94 % relative humidity because pores are too large. Up to 90 % relative humidity the strength decreases regularly. From 90 % to 94 % a great decrease is observed ; it could be explained by the capillary effects and the moisturizing of some minerals. The hydrous cycle imposed to the rocks in the mine has been modeled with an 1D fully coupled code for partially saturated porous media. The computations have shown an important decrease in the total stresses at the wall during the desaturation stage and an important increase during the re-saturation stage. These variations could induce a rock mass damage and instabilities, and highlight the necessity of a modeling with a well-adapted geometry. KEY-WORDS : iron mines, partially saturated, suction, strength, modeling. ZUSAMMENFASSUNG : Das mechanische Verhalten von teilweise gesättigten Eisenerz wird durch einachsige Druckversuche untergesucht. Die Prüfkörper haben einen durch Salzlösungen gestimmten kapillarischen Druck. Sie bleiben kaum gesättigt (32 %), sogar bei einer relativen Feuchtigkeit von 94 %, aufgrund der Anwesenheit von Mesoporen. Bis eine relative Feuchtigkeit von 90 % verringert sich gleichmässig die Druckfestigkeit und zwischen 90 % und 94 % merkt man eine starke Abnahme in Verbindung, möglicherweise, mit kapillarischen Effekten und Hydratation von bestimmten Mineralen. Die nümerische 1D Modellisierung des gezwungenen Wasserzyklus im Stein der Mine ist mit einem für porösen Medien ganz vernetzten Rechnungcode geführt. Sie zeigt besonders ein bedeutendes Sinken der Gesamtspannung während der Entwässerung und eine bedeutende Steigerung während der Sättigung. Diese Veränderungen könnten die Beschädigung des Gesteines herbeiführen und die Grundlage von Unstabilität sein. Sie unterstreichen die Wichtigkeit eine Modellisierung mit einer gut geeigneten Geometrie. STICHWÖRTER : Eisenminen, teilweise gesättigt, kapillarischer Druck, Druckfestigkeit, Modellisierung.

Jan 1, 2003

By Joel N. Van Sant

An investigation was conducted to study possible sources of Utah refractory and structural clays that could be used for the manufacture of refractories and light or buff burning heavy-clay products. A field study was made and the clay samples tested to determine their firing characteristics. Results of the Bureau's work indicate many small noncommercial deposits of hypogenic clay occur in igneous rocks. Commercial hypogenic deposits are mostly halloysite clay developed by hydrothermal replacement of limestone. The high firing shrinkage of halloysite precludes its use as a refractory, however, halloysite produced at the Dragon Mine south of Eureka, is used for making oil catalysts. Clays and shales suitable for low heat duty refractory products are found in the Manning Canyon shale, in shales associated with coal bearing rocks, and in the Dakota formation. Some of the clays from the Dakota formation are also suitable for high-duty refractory products.

Jan 1, 1964

By P. Pyykkö, E. Peuraniemi, J. Järvi, P. V. Latostenmaa, V. Törölä, S. Junnikkala

"Nickel concentrate smelting started in Harjavalta in 1959. First, flash smelting - Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes. In 1995 the original smelter flow sheet was simplified with the novel DON (Direct Outokumpu Nickel) technology. In Harjavalta with the DON technology, high-grade nickel matte with low iron content is produced in flash smelting furnace directly without subsequent converting stage. The metal values in the smelting slag are recovered in an electric furnace as an iron containing bottom alloy. Main special features in Boliden Harjavalta nickel smelter are smelting of high-magnesia concentrates, the high recoveries of nickel and copper, as well as those of PGM`s and cobalt.Sulfur and dust emissions to air can be seen generally as one main disadvantage of nickel smelting operations. In Harjavalta continuous improvements in environmental performance has been rewarded by minimum sulfur and dust emissions to the environment and working atmosphere. Today Boliden Harjavalta’s nickel smelter is presenting state-of-art-technology at nickel smelting.This paper describes the nickel smelter process and includes recent production and emission data. It describes features required to achieve environmental and occupational hygiene goals and compares environmental performance data to that published on other smelting operations. General description of New Boliden Way is presented and a case example of production stability project is also presented."

Jan 1, 2014

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease with increasing volume, while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. However, as every ventilation instructor knows, the fact that head loss is a negative number (debit) and fan head is an energy addition (credit) is often a stumbling block to student or audience comprehension since the curves seem to reflect the opposite. It is possible to use the intuitively correct curves- pressure losses as negative values and energy additions as positive values - and still obtain the correct operating point. Adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure. With the standard approach, it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1999

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt's design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977

By H. H. Murray

The largest reserves of palygorskite in the world are located in Anhui and Jiangsu Provinces in East Central China. The deposits are Middle Miocene in age and range from 3 to 6 m in thickness. The deposits are the alteration product of basaltic volcanic ash. The Chinese Geological Survey estimates the palygorskite reserves are in excess of 200 million tons. The elongate particle shape results in unique colloidal properties. Large quantities are exported to Japan, Taiwan, Southeast Asia, New Zealand, Australia, and West and Gulf Coasts of the United States. The markets include agricultural carriers, paint, joint tape compounds, animal feed binders, catalyst support, drilling muds, and suspending agents for chemicals, pharmaceuticals, and medicines. The viscosity is high and the quartz content is generally 5% or less.

Jan 1, 2009

By W. J. Birch, R. Farnfield, S. Hosein, C. Johnson

Modern smart phones include accelerometers based on MEMS (Micro Electro Mechanical System) technology giving the possibility to measure both acceleration and orientation. The widespread use of such phones has driven technological development to such a degree that it is now possible to obtain a triaxial accelerometer unit, that also include signal conditioning and analogue to digital conversion, in a package smaller than 1 cm2 (1/2 sq.in) for a relatively low cost.

Feb 6, 2023

By Virgil A. Marple

The objective of this contract was to conduct characterization, evaluation and/or calibration studies of instrumentation used for measuring the quantity of respirable dust in mining atmospheres. Initially, this work involved the upgrading and detailed evaluation of the aerosol test chamber and the development of impactors with respirable classification characteristics. These were used as standards in the chamber for measuring the quantity of respirable dust based on either the ACGIH or BMRC respirable dust criteria. A program was then conducted to calibrate several photometers. In addition, the mass sensitivity of the GCA RAM-1 photometer to water droplets in the respirable size range was determined. Three additional studies were also made in this program. First, an experimental study was performed to ascertain the effect of crosswind, cyclone orientation and particle size on particle sampling and penetration through the 10 mm Dorr-Oliver cyclone. Second, a theoretical study was conducted to refine the theory used to predict the particle collection characteristics of impactors. Third, filter samples with known quantities of diesel and coal particles were produced and delivered to the B. of Mines for testing a Raman scattering analysis technique to discriminate diesel particles in the presence of coal dust.

Jan 1, 1984

By T. A. Sullivan

The work described in this report was undertaken to evaluate and develop techniques for determining the oxygen content of titanium and titanium alloys. Early investigations of volatilization techniques involving halogenation were unsuccessful. Later efforts were concentrated on evaluating vacuum fusion and inert-gas fusion techniques. Two vacuum fusion methods and an inert-gas fusion method were found to be satisfactory in the 0.02 to 1.00 pct., oxygen range. These methods are described in detail. The coefficient of variation by any of the three methods is approximately 5 pct, While the main portion of this paper is devoted to the vacuum and inert-gas fusion methods, a resume of other suggested methods for analyzing titanium for oxygen also is given. INTRODUCTION The Federal Bureau of Nines has conducted research on titanium metal since 1938. This research included development of the Kroll process for the production of titanium (2)4, various sodium reduction processes for making titanium metal and lower valent titanium chloride-sodium chloride mixtures (17), and a fused salt electrolytic process for Me production of high-purity titanium metal and the recovery of titanium by electrorefining from off-grade materials (20).

Jan 1, 1961

By Fred D. Wright, Philip B. Bucky

FOREWORD By E. D. Gardner[$] THE present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems. INTRODUCTION The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.1 As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining cost. It was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1947

By Phillip R. Moyle

Several deposits in the Sheep Hole/Cadiz Wilderness Study Area (WSA) have small identified or potential for undiscovered gold and silver resources. One prospect area is a potential target for molybdenum. Most base and precious metals and one uranium deposit in the study area are of the fissure-filling, contact metamorphic type associated with late stage fluids of the Cretaceous Cadiz Valley batholith. Some evidence suggests limited Tertiary and Quaternary mineralization. Mineral deposits are controlled by faults, shear zones, and joints which strike northwest and dip northeast or southwest. Although undefined, calcium, sodium, lithium, and strontium brines are inferred within the study area. Some potential for oil and gas and geothermal resources is indicated by the interest private industry has shown in the eastern part of the study area. INTRODUCTION The U.S. Bureau of lines and U.S. Geological Survey conducted a mineral survey of the Sheep Hole/Cadiz Wilderness Study Area (p1. 1) which encompasses approximately 205,000 acres (83,000 ha) in south-central San Bernardino County, California. The U.S. Bureau of Mines studied the mineral resources of mines, prospects and mineralized areas; geological, geochemical, and geophysical investigations were conducted by the U.S. Geological Survey.

Jan 1, 1982