Search Documents

By Irving Hartmann

1. Under the conditions of the tests described herein, the proper use of an incombustible stemming plug of the type discussed prevented ignitions of gas in all tests during the firing of 21 single shots of permissible explosive in cool. In two tests with multiple blasting (four and five shots each) no ignitions resulted. 2. The results of a few tests in this investigation and of numerous tests made previously indicate that fire-clay stemming of the same weight as an incombustible plug provides about the same degree of protection as the plug against gas ignitions during blasting of coal by permissible explosives. 3. The hazard of gas ignition on firing charges of non-permissible 40-percent gelatin dynamite in coal was reduced but not eliminated when the shot holes were stemmed with one or two incombustible plugs or with an equivalent weight of fire clay. 4. On the basis of this investigation, the Bureau of Mines considers the proper use of incombustible stemming plugs of the design tested, under the conditions of the tests described in this paper, to be of equivalent safety as the same weight of fire-clay stemming. This report does not constitute approval or disapproval of the incombustible stemming plugs by the Bureau of Mines. 5. The test data indicate that misfired charges in shot holes stemmed with the incombustible stemming plug cannot be disposed of with certainty by the procedure recommended by the manufacturer. In this investigation the misfired charges failed to detonate in 30 percent of the trials.

Jan 1, 1950

By K. Zenger, J. Kaartinen, J. Huuskonen, S. Torttila, S. Lähteenmäki, J. Pietilä

"Pyhäsalmi Mine in Finland has a long history of continuous process development. The concentrator processes Cu-Zn-sulphide ore with high recoveries. An on-line flotation simulator has been developed to maintain and further improve the flotation performance. Consisting of a flotation kinetic dynamic model, and interconnected with process control software, the simulator can be used for training new control room operators in various scenarios. For daily operation, the model parameters are continuously adapted to take into account the changing process conditions. On-line simulator tracking the process can provide the process operator new information in several ways: a) values of unmeasured process variables are obtained by displaying the corresponding simulator values, b) predictions of future process states and outputs are calculated and displayed, c) information of changing process parameters can be used as an indicator of e.g. change in the processed ore type. This paper describes the adaptive simulation system and its usage at the Pyhäsalmi concentrator.IntroductionPyhäsalmi massive sulphide orebody is located in central Finland. Operation of the mine started in 1962 and it is currently producing copper (Cu), zinc (Zn) and sulphur (S) concentrates. The concentrator control and optimization system has a long history of successful continuous development during the past decades (see e.g. Huuskonen & Moilanen, 2010). An on-stream analyzer has been a part of the automatic process control since 1968 (Lähteenmäki, Miettunen & Saloheimo, 1999). First control algorithms based on a flotation mathematical model were developed in 1971 (Koivistoinen & Miettunen, 1985). In 1990’s the development of a froth machine vision systems started (Kaartinen, 2009; Kaartinen, Roine & Hätönen, 2009). More recently Pyhäsalmi Mine Oy has been involved with several national development projects dealing with particle size distribution measurements (Kaartinen & Tolonen, 2008), spectral analysis of flotation slurries (Haavisto, Kaartinen & Hyötyniemi, 2008), and dynamic simulation of flotation processes. The latter topic is further elaborated in this paper."

Jan 1, 2015

By A. Ebrahimabadi

Roadheaders are very versatile excavation machines used in tunnelling, mine development, and mine production for soft to medium strength rock formations. Performance prediction is an important factor for successful roadheader application and generally deals with machine selection, production rate and bit consumption. Among many different parameters, brittleness is also one of the material properties related to breakage characteristics and can be used as a cuttability parameter from a mechanical excavation point of view. The main objective of the research study is to contribute the brittleness of rock excavated to construct a new empirical equation for predicting the performance of roadheaders in different material and operational conditions. In this regard, a new performance prediction model for medium duty roadheaders based on a brittleness index (BI) is presented. In this study, rock mass brittleness index (RMBI) is defined in order to investigate the influence of BI on roadheader performance. RMBI is an index which can be used to relate the intact and rock mass characteristics to machine performance. Results demonstrated that RMBI is highly correlated to instantaneous cutting rate (ICR) (R²=0.94). Moreover, through the further analysis and normalization, the pick consumption index (PCI) was introduced as a parameter having a good relation with pick or bit consumption rates (PCR) (R²=0.79). Finally, the new predictive models for ICR and PCR showed very good correlations with the actual measured values. Keywords Performance prediction, roadheader, brittleness index, mechanical excavation.

Jan 1, 2011

By Luis Valentim, Terry Cousins

The goal of a mine is to produce ore at the lowest possible cost with due regard to safety of pemonnel and equipment. The mining process consists of a number of discrete operations such as planning, drilling, blasting,excavation, transportation and crushing. These processes are interrelated and cannot be considered as separate activities when optimising output and minimising cost. In order to optimise the global costs it may therefore be necessary to increase cost in one area such as blasting design and management beyond the norm.

Jan 1, 1998

By Thomas Varley

[For a year or more, statements have appeared in the technical press, and Especially in various trade journals, indicating that valuable metals such as gold, silver, platinum, and other rare metals, have been found and also have been successfully extracted from oil shales. These reports stated tat decarbonization and special methods of chlorination treatment, leaching and subsequent Precipitation, also cyanidation followed by table concentration of the residues after cyanidation, all indicated that told ad silver and other metals could be, and were, successfully recovered. Such articles have caused much misunderstanding, and as the correctness of some re of the statements made in them were questioned by some of the technical journals and by various chemists and metallurgists, an investigation of the subject. was begun by the metallurgical division of the Bureau of Mines, in order, if possible, to determine to what extent, if any, metals of value do occur in oil shales, and if so, the feasibility of attempting their recovery by tie processes said to have been used for teat Purpose. Inasmuch as the Bureau's station at Salt Lake City is investigating the recovery of oil from oil shales, the investigation of too recovery of metals from oil shales was assigned to my direction as superintendent 'of that station. An agreement had been entered into with the owner of m extensive oil shale deposit in Wyoming whereby I would personally collect the samples' of shales for use in the investigation.]

Jan 1, 1922

By Z. Zhang, M. -Y. Liu, X. -G. Chen, F. Breton

"The microstructures of AlSi10Mg foundry alloy in permanent mould (PM) and high pressure vacuum die (HPVD) castings were analyzed and compared. The as-cast microstructures of two castings mainly consisted of eutectic silicon particles, primary Mg2Si and Fe-rich intermetallic phases. The surface layer in HPVD castings, which has a unique feature and different structures, was carefully characterized. The dimension variation of microstructural phases along the cross section in PM samples is less than that in HPVD samples, although the size of microstructural phases in PM samples was much larger than that in HPVD samples. The mechanical properties of PM and HPVD samples were evaluated on as-cast and T6-treated conditions. The tensile properties of HPVD castings are remarkable better than those of PM castings on the as-cast condition. The T6 heat treatment greatly improves the tensile strength of PM castings while it has limited impact on the tensile strength of HPVD castings.INTRODUCTION The AlSi10Mg alloys are widely applied to the high pressure die casting (HPD) and high pressure vacuum die casting (HPVD). In the HPD process, the melt is injected into the die cavity under a high speed (30–50 m/s in the gate velocity for aluminum alloys), and solidified under a high pressure (up to 200 MPa in the cavity) and with a high cooling rate (up to ~103 Ks–1) (Gourlay, Laukli & Dahle, 2007; Ji, Wang, Watson & Fan, 2013). This results in a unique microstructure feature that is different to other casting processes under gravity. One major concern in HPD castings is porosity due to trapped air in the cavity (Ji et al., 2013), which seriously restricts the application of a heat treatment on the improvement of mechanical prosperities because of the formation of blisters on casting surfaces. For the process improvement, the high pressure vacuum die casting was developed in 1980s (Uchida, 2009). In this process, the melt is injected into the die cavity under reduced pressure (vacuum), which greatly reduces gas porosity in castings due to effectively avoiding the trapped air. Consequently, HPVD castings are heat-treatable without the formation of blisters on castings surface during heat treatment. The HPVD process has been widely applied to produce high quality structural castings in recent years attributed to reliable vacuum system development (Uchida, 2009). However, the microstructure features of HPVD castings are not systemically characterized yet."

Jan 1, 2018

By J. A. L. Napier

This paper presents an overview of work carried out by the CSIR Division of Mining Technology and formerly by the Chamber of Mines Research Organization (COMRO) to quantify the behaviour of the stope fracture zone near deep level goldmine stopes. The motivation for this work is first reviewed in the context of the unsatisfactory status of current mine layout design criteria. Numerical methods to represent failure processes are reviewed briefly. Specific studies of microfracture processes are described as well as physical modelling experiments that can yield insights into deformation mechanisms. Modelling of stope scale deformation mechanisms are presented and considerations relating to elastodynamic modelling of the rock mass are described. The implications of this understanding in relation to prospects for active fracture zone ?engineering? are outlined and finally, the directions of future research work are proposed.

Jan 1, 1997

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to ma e these questionnaires as complete as possible.

Jan 1, 1963

By J. O. Lewis

In its efforts to reduce waste, and increase efficiencyin oil production, the Bureau of Mines is investigating methods of increasing the recovery from the underground sources of supply, which are the foundation of the petroleum industry and the many allied industries wholly or partly dependent on it. In the face of a demand that is increasing faster than the production and that, in the consensus of opinions of well-informed authorities, is soon likely to outstrip the productive capacity, it is well to consider whether it is not possible to extract more oil from the known sources of supply. It is universally acknowledged that by the usual production methods much oil is left underground, the general opinion being that at least 50 per cent of the oil in a field remains unrecovered when the field is abandoned as exhausted. From the writer's own investigations he believes the average recovery is even less, and if any considerable portion of this oil being left underground could he made available it would have a tremendously favorable influence on the petroleum industry and all the industries dependent on it. In this publication are considered the principles involved in increasing recovery and methods of extracting more oil from the oilbearing formations than by the usual ways of producing. These methods are: The use of gas or vacuum pumps, forcing compressed air or gas through the oil-bearing formations, displacing the oil by water, and better utilization of the natural pressures in the oilhearing formations. Especial attention is being given to a processcommonly known as the Smith-Dunn-for forcing compressed air through oil-bearing formations because it is believed to hold most promise for the future.

Jan 1, 1917

By Cornelius F. Kelley

DURING the war, events moved with unprecedented rapidity. Situations, industrial, economic and financial, arose over night that stressed to the uttermost the ingenuity and ability of those who dealt with them. It was essentially a time demanding action rapid and concentrated, and not one for discussion, either academic or polemic. As a result, matters of importance were necessarily transacted without the desirable opportunity being afforded of enabling a general understanding to be gained as to the relative merit or demerit involved, and in some instances, legislation essential to enable the consummation of an important matter was passed without attracting the public attention then deeply engrossed in the larger aspects of the situation. The result was that so long as the public mind was occupied, little or no concern was given to questions that ordinarily would have invited immediate attention; and in some instances, only when as an aftermath of war a particular subject has become a matter of discussion, criticism not altogether fair is made without first obtaining accurate knowledge as to the conditions that prevailed, the purpose sought to be accomplished, or the results obtained by the action taken.

Jan 1, 1921

By D. Silva-Galvan, R. D. Morales, S. Gonzáelez-López, A. Romero-Serrano, G. Plascencia-Barrera, F. Chavez-Alcala

This work is focussed on lead decopperising by two techniques: conventional top addition of sulfur and injection of sulfur powder. It is found that the first method proceeds under equilibrium conditions and the second one depends on kinetic considerations. Experiments were carried out using 15 kg lead baths at two temperatures, 340°C and 380°C. The carrying gas used for the injection trials was nitrogen at flow rates of 6.3 and 18.6 L min- 1• The results show that 'decopperising process is more efficient at temperatures close to the melting point of lead for the sulfur top addition process, whereas high temperatures produce better copper removal for the injection of sulfur powder. Besides, the sulfur injection with the higher nitrogen flow rate (18.6 L min-1) produced higher decopperising rates. Thermodynamic and kinetic models are used to simulate this lead refining process.

Jan 1, 2000

By J F. Seale

The design of the settling pond for the Malvern Hills opencast coal project was based on a primary requirement to control runoff and sediment generated from the immediate 6 ha mine catchment, which included two seepages from old underground workings. The pond has been particularly effective in controlling turbidity in the outflow water, with the consent limit of 50 NTU being met on all but one occasion and normal levels of discharge less than 10 NTU. Water quality testing carried out at the time of consenting indicated that there were no acid-generation issues with the proposed mine site in dominant mudstone strata of the Broken River Formation, and that water from the old mine workings was near-neutral in terms of pH and well-buffered. However, it became apparent over the very dry summer of 2003 - 2004 that slaking of the exposed mudrocks in the mine batters was resulting in significant acidity generation, and outflow pH levels were well below the consent limit of 6.5 during and following periods of rainfall. Although these acidity problems have been remediated in the short-term by the use of lime products, it is clear that a programme of lithotype characterisation for AMD should have been undertaken and this has now been implemented. Design of long-term acid drainage control measures is being carried out, and will probably be based around the use of hydrated lime for pH control with enhancement of natural wetlands.

Jan 1, 2004

By R. J. Matetic, J. S. Peterson, P. G. Kovalchik

The National Institute for Occupational Safety and Health (NIOSH) has initiated a study of a roof bolter to reduce noise exposure to mine roof-bolter operators. An important segment of this research entails determining the affect of various drilling configurations on the performance (penetration rate) and sound power emissions when drilling into granite. Test conditions included using various combinations of rotational speeds and thrusts, using 2.54- and 3.49-mm- (1- and 1 3/8-in.-) diameter hexagonal and round drill steels, using vacuum and wet conditions and using drill media of differing compressive strengths. This paper details the affects of each of these variables on the performance and sound power level emission. When drilling into granite, it was found that wet drilling generated lower sound power levels and performed better than vacuum drilling.

By L. S. Harner

This paper which describes the milling practice at the Golden Cycle mill is one of a series of similar papers being prepared by the United States Bureau of Mines. The mill of the Golden Cycle Corporation, formerly known as the Golden Cycle Mining and Reduction Co., is located at Colorado Springs, Colorado, and has been operated since 1907. It is now and has been from its inception almost exclusively a custom mill.

Jan 1, 1933

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to make these questionnaires as complete as possible.

Jan 1, 1963

By Flavio Begazo Mamani

Recientemente Southern Perú desarrolló un nuevo proyecto donde se modernizaba la planta de Fundicion y se reemplazaba el convencional horno reverbero por la tecnología del ISASMELT, capturando más del 92% de los gases generados durante el proceso de fusión de los concentrados de cobre. En ese sentido, el presente texto describo los efectos de la modernización de la Fundición sobre la calidad anódica. Antes de la modernización de la Fundición, los ánodos fueron producidos en la planta de ánodos ubicada en la Refinería de Cobre de Ilo. Ahora los ánodos son producidos directamente en la Fundición y como resultado, la composición química de los ánodos ha cambiado, principalmente en el contenido de bismuto, antimonio, plomo y zinc, siendo diferentes a los parámetros de diseño original de la Refinería. Asimismo, este factor impulsó a revisar el proceso de remoción de impurezas y los parámetros de la refinación electrolítica en la Refinería para evitar la contaminación del cobre refinado, logrando mantener la continuidad de la producción de cátodos de cobre de alta calidad superando los estándares interna-cionales de la norma ASTM-B115.

Sep 12, 2011

By R. A. Kearns

Biennially the Bureau of Mines issues a list of equipment that has been accepted as approved or permissible during the two calendar years immediately preceding the date of publication of the listing. By so doing the mining industry is kept informed of the availability of the latest equipment for safe use underground. This list supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953; Information Circular 7722, Permissible Mine Equipment Approved During the Calendar Years 1953-54; Information Circular 7840, Permissible Mine Equipment Approved During the Calendar Years 1955-56; and Information Circular 7957, Permissible Mine Equipment Approved During 1957-58. This list includes equipment meeting those standards that have been revised since Information Circular 7957 was .issued. Schedule 16E,4 a revision of Schedule 160, was approved May 19, 1960.

Jan 1, 1961

By B. S. Spottiswoode

Lack of visibility makes it difficult for continuous miner (CM) operators to judge the desired sump depth. The resulting inaccuracies have proven to lead to significant production losses. This problem of measuring the depth of sump has been addressed in the past and a few measurement techniques have evolved. Despite various attempts, a suitable commercial depth of sump sensor does not yet exist. A system using the Doppler effect has been patented, developed and successfully tested. The method is non-intrusive and involves a beam of microwaves being projected obliquely at the roof. The received signal is analysed with respect to the transmitted signal, yielding the desired measure of displacement. Surface tests have revealed an accuracy of a few centimetres. Underground simulation tests on a load haulage dump (LHD) machine have verified the repeatability under the harsh conditions of interest. The system is presently being installed on a CM where it is to undergo a long-term performance evaluation. This paper presents the theory behind such a system, the hardware developed, the signal processing requirements and an analysis of the test results.

Sep 1, 2001

By M. W. Hildyard

The aim of this paper is to demonstrate that active seismic measurements could have an impact in helping solve rock engineering problems experienced in the South African mining industry. The paper presents a variety of experimental and numerical results where seismic waves show clear differences in wave-speed and amplitudes due to different degrees of fracturing. It presents results from the ?Omnibus? project commissioned to develop new ultrasonic technologies for diagnosing fracturing for nuclear waste repositories. This included using models to investigate assemblies of cracks where the effects of crack density and crack size on waveforms are shown to be coupled. Results indicate that these effects can be decoupled in the frequency domain, where the Fourier amplitude aids in estimating crack size, while the low frequency phase-difference has a direct relationship to crack density. Models are also shown to aid interpretation of waveforms by isolating geometric effects from the effects due to cracks. Two rock engineering problems experienced in the South African mining industry are investigated through numerical examples. These demonstrate that determining whether ?crush? pillars have failed and determining the degree of fracturing in the hangingwall of stopes, may be possible through the use of active seismic surveys.

Jan 1, 2005

By A. Mitura

The paper presents the initial investigation of possible energetic applications of chosen wastes from groups: 06, 03, 05 and 01, including coal slimes being secondary product of hard coal processing. These categories of wastes are catalogued according to the polish law, where 06 ? wastes from production, preparation, purchasing and application of products of non-organic chemistry; 03 ? wastes from wood processing and from plates and furniture, celluloid mass, paper and card board production; 13 ? oil wastes and wastes from liquid fuels; 01 ? wastes produced by searching, extracting, physical and chemical processing of ores and other mineral raw materials. The change of combustion heat value was evaluated in produced energetic mixtures containing these types of wastes together with the change of their individual components. All combinations of ingredients were taken into consideration giving 256 various mixtures, from which 36 were selected to investigation. This allowed the performance of statistical factor analysis. For such prepared materials the application of regressive method was proposed in purpose of calculating combustion heat value and then the comparison of empirically determined and theoretically calculated heat values was performed. The change of regressive coefficients can be determined by the nature of Hess law (eq. 1) what was investigated and the attempt of its explication and validation was done.

Aug 1, 2013