Search Documents

By C. W. Elder

"INTRODUCTION This report describes a method of horizontal drilling in an oil-producing formation underlying a 400-acre, approximately square plot of land in the Franklin Heavy oil field in Sugar Creek Township, Venango County, Pa. The method, which was developed on two previous projects in Ohio, 3/ consists of sinking a shaft to the bottom of a shallow oil sand and drilling holes in a general horizontal plane outward from the chamber in a pattern similar to that of the spokes of a wheel. The project was undertaken by the Venango Development Corporation in an attempt to find an efficient method of recovering oil from partly depleted sand formations.The Venango Development Corporation is composed of the following oil-producing and oil-refining companies and individuals: South Penn Oil Co., Forest Oil Corporation, Kendall Refining Co., Minard Run Oil Co., Quaker State Oil Refining Co., The Pennzoil Co., Alliance Oil Corpo¬ration, United Refining Co., Franklin Creek Refining Corporation, Canfield Oil Co., Pennsylvania Refining Co., Page Oil Co., Freedom Oil Co., D. W. and D. S. Grant, and J. P. Herrick, C. M. Davison and N. V. V. Franchot. Engineering features of the project were supervised by a committee off three engineers A. J. Saxe, chairman, W. M. Shoemaker, and C. N. Pfohl, who supervised the excavation of the shaft and the drilling of the first two holes by alternately spending a week at a. time at the project. The drilling method was under patent license from Leo Ranney, who served as technical advisor to the Venango Development Corporation; in addition, he furnished the design for the shaft and work chamber."

Sep 1, 1944

The principal source of funding the working capital requirements of gold miners has traditionally been equity. However in the 1980s, with a substantial increase in activity in the exploration for, and the production of, gold the traditional sources of equity finance became no longer sufficient to meet demand. With the often high cost of raising equity, the need for developing alternative financing structures became critical, especially since the stockmarket crash of 1987 which at least until recently, adversely affected the amount of equity capital available for investment in mining.

Jan 1, 1994

By Terry A. Lee

The grade of mineral resource estimates underpin all major economic considerations of mining prospects. While there are reporting requirements to satisfy when stating a mineral resource estimate, an examination of NI 43-101 style reports suggests that authors believe that there are a number of ways of addressing these requirements. As a reader of these reports, some processes are helpful and others are not so in getting a real appreciation of how realistic is the mineral resource estimate. Critical to the quality of the mineral resource estimate is how realistic is the economic mineral concentration component. In many cases, this parameter is called grade. The industry experiences increased difficulty in achieving realistic grade estimates as the sample grade variability increases. The level of transparency in a mineral resource estimate is very much a function of the competence of the author. An objective presentation of the critical data, such as grade sampling variability can assist a reader in determining if the geology of the mineral concentration is adequately understood and how realistic is mineral resource grade estimate. This paper has considered 75 NI 43-101 style reports released in the past 2 years. The review demonstrates features that were helpful in determining how realistic the mineral resource grade estimate is. If there is insufficient transparency in a report, there is a high probability that the mineral resource grade estimate will not be realistic.

Apr 1, 2005

By A. W. Frolli

This paper, describing the open-cut mining milling, and cyaniding methods and costs at the Yellow Aster gold mine, is one of a series being prepared by the Bureau of Mines on similar practices in the United States. It is presented primarily to show methods and costs of mining and treating low-grade gold ore on a large scale.

Jan 1, 1940

The Aluminum Company of America (Alcoa) announced that the second unit at its experimental facility at Palestine, Tex. would begin production -in 1979, increasing the capacity of the facility to 30,000 tons per year. The plant uses an experimental process based on the electrolysis of aluminum chloride and reportedly uses 4 to 5 kilowatt hours per pound of aluminum produced, compared to an industry average of about 7 to 8 kilowatt hours per pound. Alcoa has reportedly signed a letter of intent with the Chinese government under which Alcoa will conduct feasibility studies on two new integrated aluminum projects and modernization of an existing aluminum plant. If the study results are favorable, Alcoa Engineers Inc. and the Import and Export Company of the Chinese Ministry of Metallurgical Industry could negotiate agreements to provide Alcoa technology and services for the projects.

Jan 1, 1979

By Michael Rieber

The increase in f.o.b. mine prices of coal from $5/ton to over $18/ton in five years [1] has increased the significance of transportation costs. Coals produced in the vicinity of the consumer bear a much lower transport cost than those produced in the west. This differential may be used for flue gas desulfurization, other cleaning, or further processing of local coals. To the extent that western coals are cheaper to produce and have a lower sulfur content, they offset the locational disadvantage. To the extent that they have a lower heating value, the disadvantage is exercabated. Given the other conditions, an accurate analysis of transport costs will help suggest the location of coal mining and the moue of transport both transport costs and tariffs have risen. Together they have increased delivered coal prices, altered the balance between the use of coal and other fuels, helped to alter the location of mining activity, and put pressure on consumers to examine the cost effectiveness of alternative transport modes. Transportation options for long distance coal movements include rail, barge, pipeline, and EHV transmission lines. A summary of system parameters is shown in Table 2.1. Barge transport, pneumatic and slurry pipelines are discussed elsewhere in this report. Together with EHV, they have been the subject of previous studies [2,3,4]. Slurry pipelines have been shown to be especially useful where rails are not available [2] but the technical problems of dewatering, handling, and utilization of lines [5] remain unresolved. They are discussed in Section 3. Barge transportation depends on the location of the mine and consumer with respect to the waterway system. One drawback of barge shipment is interruptions due to winter, and low or high water conditions. Mine mouth power generation followed by EHV transmission of over 500 miles has been shown to be the most expensive means of delivering an equivalent amount of energy to consumers [2].

Jan 1, 1977

By Walter R. Storms

"INTRODUCTION The New Mexico potash exploration described herein was begun in February 1944 with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the Reserve and in the immediate vicinity.The Potash Reserve is in secs. 26; 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of Carlsbad, as shown on figures 1 and 1A, Drilling was done in secs. 26 and 35 of the Reserve, in section 14 to the north, end sections 2 and 56 to the east. All work was done on Governnent-owned, unleased land.The Reserve may be reached from Carlsbad by traveling to the north-east by automobile for about 14 miles on the paved U. S. highway 62. This highway passes through the southern part of the Reserve. Other parts may be reached by a State highway that passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Santa Fe Railroad also passes across the southern part of the Reserve enroute from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the project and 22 miles from Carlsbad."

Aug 1, 1947

By Maurice Deul

This bulletin summarizes the work conducted under the Bureau of Mines methane control research program during the years 1964 to 1979. This research effort was directed toward improving existing methods and developing alternative methods of reducing the explosion hazard during mining. The research was performed in three general areas: (1) basic factors that control the emission of methane into coal mines, (2) methane control during mining, and (3) methane drainage in advance of mining. Topics discussed in this bulletin include the magnitude of the methane problem; the equipment and instruments developed; the geological, chemical and physical parameters that control the movement of methane in coalbeds; the direct method of determining gas content; the estimates of gas content from adsorption data; and methane drainage, through shafts, through horizontal boreholes, through vertical boreholes, or through slant holes. Improvements in ventilation, control of methane in gob areas, and water infusion are also discussed, as is the potential use of coalbed methane as a supplement to natural gas supplies. This bulletin provides a comprehensive source of information on the accomplishments of the Bureau's methane control research program, on the technology developed, and on the direction of further research.

Jan 1, 1986

By Murillo Romero da Silva

Ligas com memória de forma (LMFs) são ligas metálicas capazes de recuperar o seu formato e tamanho original após deformação plástica quando aquecidas acima de uma temperatura crítica. Diversos casos de possíveis aplicações paras as LMF têm sido justificados no campo científico, com alguns poucos casos identificados para aplicação em massa, existindo uma ausência na literatura de uma análise crítica da aplicabilidade das mesmas que leve em consideração aspectos industriais e de mercado. Dessa forma, se faz necessário um estudo mais aprofundado que correlacione as ideias científicas geradas com a produção industrial e com a comercialização de LMFs. Nesse contexto, o trabalho visa através de levantamento e análise de patentes e artigos científicos, assim como por contatos industriais, estabelecer uma relação entre o desenvolvimento científico e o comercial das LMFs. Mais de 11 mil artigos e mais de 7 mil patentes foram produzidos nos últimos 16 anos, sendo observado uma tendência crescente da criação de conhecimento de LMF, o qual já vem sendo aplicado na indústria, justificando assim os esforços observados no campo científico. A área biomédica se destaca como a mais bem estabelecida no campo das LMF, com destaque para a utilização das ligas a base de NiTi.

Aug 17, 2017

By R. S. Dean

As set forth in the decision of the Trail Smelter Arbitral Tribunal, dated April 16, 1938 This Tribunal is constituted under and its powers are derived from and limited by the convention between the United States of America and the Dominion of Canada signed at Ottawa, April 15, 1935, duly ratified by the two parties and ratification exchanged at Ottawa, August 3, 1935 (hereinafter termed "the Convention") . . . The duty imposed upon the Tribunal by the Convention was to "finally decide" the following questions: (1) Whether damage caused by the Trail Smelter in the State of Washington has occurred since the first day of January 1932, and, if so, what indemnity should be paid therefor? (2) In the event of the answer to the first part of the preceding Question being in the affirmative, whether the Trail Smelter should be required to refrain from causing damage in the State of Washington in the future and, if so, to what extent? (3) In the light of the answer to the preceding Question, what measures or regime, if any, should be adopted or maintained by the Trail Smelter? (4) What indemnity or compensation, if any, should be paid on account of any decision or decisions rendered by the Tribunal pursuant to the next two preceding Questions? In this decision reported to the Government of the United States of America and to the Government of the Dominion of Canada, the Tribunal answered the first question in its entirety and reserved decision on the other three questions in accordance with the following extract from their decision

Jan 1, 1944

By A Hollweg, K H. Esbensen, M Lischka

Two new splitter designs for intercepting moving streams of matter are presented, the variable cross-stream splitter (vCSS) and the rotary stream splitter (RSS), which are intended for implementation in a fully automated modus. The vCSS facilitates obtaining up to three subsamples with different splitting ratios from automated laboratory flow paths, while the RSS divides the intercepted sample into 16 equal analytical aliquots. The splitters can process a wide range of dry, granular and free-flowing materials (<5 mm). The required weight for each subsample can be set without mechanical adjustments in the case of the vCSS. Typical applications are subsampling/splitting for X-ray fluorescence pelletisation (or fused beads) or splitting for average shift composite sampling or grain size analysis. The vCSS combines the advantages of riffle splitting (three user-defined subsample masses) with miniature bed blending and can accept up to 15 kg in total incoming sample mass. In practice, the automated vCSS can deal with unlimited ingoing mass fluxes, while the RSS is designed to operate at a user-defined fixed subsampling rate (1/16th in the tested version). Both splitters have the potential to be optimised and evaluated according to an application/user-defined total sampling error (TSE) + total analytical error (TAE) threshold. Both splitters were tested under adverse conditions and with compositions involving three components with properties representing typical mass fluxes and components concentrations in industrial and technological systems: phosphate concentrate 89.00 per cent (<500 µm), slag ten per cent (>2 mm) and glass spheres one per cent (750–1000 µm). The slag particles vary widely in particle shape, aspect ratio and surface roughness, while the glass spheres are extremely prone to bouncing and segregation (spillage). This test system is extremely difficult to split and thus constitutes a realistic worst-case scenario. While the vCSS does not comply strictly with Theory of Sampling demands for correctness, both splitters may well be able to deliver fit-for-purpose representative results if/when tested properly. Average relative mass deviations ranged from 1.89 per cent for phosphate concentrate (relative standard deviations of 20-fold repeated splitting) to 4.72 per cent for glass spheres and 13.04 per cent for slag. For the RSS, the average replication experiment splitting variation was 2.89 per cent for phosphate concentrate, 4.82 per cent for glass spheres and 11.1 per cent for slag. Both new automated online splitters would therefore appear to be able to be tuned to fit-for-purpose representivity (defined here as maximum relative reproducibility <5 per cent) for many non-extreme materials; however, it is always imperative to test every new type/class of material empirically. There is a wide commercial potential for important materials and commodities sectors, including food, feed, drugs (pharmaceutical), secondary raw materials, recyclates, agricultural products and seeds.CITATION:Lischka, M, Hollweg, A and Esbensen, K H, 2017. New online/atline splitter designs for laboratory automation – feasibility results, in Proceedings Eighth World Conference on Sampling and Blending , pp 159–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By R. A. Isberg

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75o coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 1, 1981

By Parkhurst D. H

It is shown that a differential colorimetric technique can be used as a routine method for the estimation of titanium in beach sands, and their ore dressing products. The method will tolerate the presence of most of the other elements usually found in beach sands. The accuracy is shown to be within the limits of ±0ò31 per cent for concentrates containing more than 95 per cent titanium dioxide and ±1 per cent for tailings containing 0ò2 per cent titanium dioxide. The method is described for use with a Hilger "Spekker" absorptiometer.

Jan 1, 1957

By Ed D. Thimons, Douglas E. Pollock, Andrew B. Cecala, Gregory J. Chekan, Jay F. Colinet, John A. Organiscak

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers’ soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

By H. C. Fowler

Technical developments in the American petroleum industry as regards exploration, drilling, production, and transportation were characterized by many anomalous conditions during the half decade 1914-19. A review of the literature of that period discloses the striking fact that individual geologists, engineers, and other technologists were surprisingly well versed concerning the occurrence of natural hydrocarbons and methods of extracting them and were acquainted with many of the physical and chemical characteristics that influence the behavior of fluids in natural reservoirs. However, the industry as a whole knew little of the correct application of recognized fundamentals; indeed, judged by present standards certain expediencies of self-styled "practical' operators seem cumbersome, if not evidences of ignorance.

Jan 1, 1941

By K. K. Kelley

This work is both a revision and an elaboration of Bureau of Mines Bulletin 371, which was published in 1934 and included data available to October 1933. During the intervening years, a large number of new experimental, high-temperature, heat-content data have become available through continuous, systematic efforts of the Pacific Experiment Station of the Bureau of Mines and the Laboratory for Inorganic and Physical Chemistry of the University of Groningen (Netherlands), coupled with various individual investigations at many institutions. In addition, calculations from spectroscopic and molecular constant data have been extended and applied to a wide variety of gaseous substances. This bulletin purposes to collect and correlate all available high-temperature heat-content and specific-heat data for inorganic sub-stances and to formulate tables and algebraic expressions for their representation. It is hoped in this manner to remove some of the tedium of thermodynamic calculations for industrial metallurgical research workers and engineers who often have available only an inadequate library in this field. It is expected also that this bulletin will have value to those teaching courses in metallurgical and chemical thermodynamics.

Jan 1, 1949

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

In this study, the dissolution behavior of copper and arsenic from five different copper concentrates containing 21-34.7 %wt. of Cu, 1.3-7.3 %wt. of As and 15.6-27.5 %wt. of Fe were investigated under high pressure oxidative leaching conditions. Leaching experiments were conducted using different leaching reagents such as ferric sulfate, sodium chloride, deionized water, sulfuric acid and ferric sulfate-sodium chloride mixture in order to compare the effectiveness of each on the dissolution of copper and arsenic from copper concentrates. The effects of ferric sulfate (0.1-1 mol/L), sodium chloride (0.1-0.5 mol/L) and leaching temperature (100-180C) were investigated under 1 MPa autoclave pressure , particle size >45 m, pulp density of 100 g/L, stirring speed of 750 rpm and leaching time of 60 min. Results showed that the most effective leaching reagents for the dissolution of copper are 0.34 M NaCl and a mixture of 0.1 M Fe2(SO4)3 - 0.34 M NaCl, in which As extraction did not exceed 7%. The copper concentration in the pregnant leach solution obtained after leaching using 0.1 M Fe2(SO4)3 - 0.34 M NaCl was 13-30 g/L, while the concentration of As and Fe were in a range between 0.3-1 g/L and 0.2-10 g/L at 160C. INTRODUCTION Copper sulfide minerals, such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and covellite (CuS) are used for the production of copper in mining and metallurgical industries worldwide. The conventional pyrometallurgical processing followed by electrorefining is a common process for the production of high purity copper (Moskalyk, & Alfantazi, 2003; Padilla, Aracena, & Ruiz, 2012). However, the degradation of copper content and an increase in the amount of metal impurities, especially arsenic (As), antimony (Sb) and bismuth (Bi) in copper concentrates cause serious problems to the production of copper and environmental pollution (Basha, Selvi, Ramasamy, & Chellammal, 2008; Long, Peng, & Bradshaw, 2012). Hydrometallurgical processes are used to recover metals from refractory ores, concentrates and tailings by leaching (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018). During the last decades, hydrometallurgical processing for the recovery of copper from enargite-bearing copper ores and concentrates has been extensively investigated due to its relatively more environmentally benign and less capital costs than the conventional pyrometallurgical processes (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018; Choubey, Lee, Kim, & Kim 2018). However, several issues facing the hydrometallurgical processing are incomplete extraction of copper associated with the coprecipitation of iron compounds, difficult stabilization of toxic impurities and production of a contaminated copper product (Dreisinger, 2003; Safarzadeh, Moats, & Miller, 2014). Hence, a number of studies have been conducted on the selective dissolution of copper from copper ores and concentrates or selective removal of arsenic leaving a clean copper residue using various leaching reagents or lixiviants (Safarzadeh, Moats, & Miller, 2014; Mihajlovic, Strbac, Zivkovic, Kovacevic, & Stehernic, 2007; Tongamp, Takasaki, & Shibayama, 2009). More extensive studies on the selective extraction of copper from enargite- bearing copper ores and concentrates are much needed to improve copper recovery.

Jan 1, 2019

By Robert Bachus, Nikolaos Machairasm, Allen Cadden

Data Interchange for Geotechnical and Geoenvironmental Specialists (DIGGS) is a data transfer standard that is gaining widespread acceptance in the geotechnical and geoenvironmental communities. Originally developed using funding from the Federal Highway Administration (FHWA) to efficiently capture data related to geotechnical boring logs, cone penetration test (CPT) soundings, and lab testing results, the data transfer protocol is rapidly gaining traction. It has been shown to have beneficial impacts in other allied areas where disparate parties (i.e., consultants, contractors, vendors, etc.) routinely publish/submit data as part of project deliverables. The historic problem is that many of these submissions use paper copies (i.e., .pdf images) to transmit valuable data for the project… data that may extend beyond the “technical” aspects of the project (e.g., equipment operating conditions, construction production rates, project costs, etc.). These data could be used by multiple parties to assess project performance and safety, as well as to track productivity, etc. Currently, in the limited situations when actual data are compiled and transmitted, the data often are submitted as an author-specific (and often proprietary) software application and must then be re-entered into other software applications (e.g., analysis software, database, etc.) for use beyond simple data collection. An initiative undertaken by the Geo-Institute (G-I) of the American Society of Civil Engineers (ASCE) focuses on exploiting the full potential of DIGGS to geoprofessionals both within and outside of the transportation community. The deep foundations industry represents one community that could benefit significantly from using DIGGS. Data of interest to DFI members include production records, quality assurance information (e.g., verticality and alignment, concrete strength), and, importantly, load test results. When adopting DIGGS, users need not modify how they capture data, but rather will use DIGGS as a vehicle to transfer data to other applications in a standard format where it can be shared, used, stored, and retrieved. This paper and associated presentation will describe DIGGS and demonstrate how DIGGS can be used effectively within the deep foundations community.

Jan 1, 2019

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

This study presents the results of the mineralogical characterization of Ti-Zr ore from the Jiboia deposit, located in the municipality of Brejo Grande, Sergipe State, Brazil. The goal is to identify the main Ti, Zr, and REE carrier phases in the different particle size fractions in order to subsidize the development of a cost-effective processing route for the production of heavy minerals concentrate. The mineral resources are estimated at 31.5Mt @ 3.5% of total heavy minerals (THM) for the Jiboia Ti-Zr deposit, of which 5 Mt @ 3.39% THM were classified as measured and indicated. The mineralogy of the heavy mineral concentrate recalculated to 100% is represented by 22% pseudorutile, 20% ilmenite, 15% zircon, 5% rutile, 2% monazite, and 36% gangue. The ore minerals are preferably concentrated in the 150 × 53-μm granulometric fractions, which represents 80% of the THM and only 27% of the ROM (Run-of-Mine) ore. Therefore, by cutting the ore to 150 μm, it is possible to discard 73% of the ROM mass and recover 80% of the THM, including 100% of the zircon and monazite which are the most valuable minerals present in the heavy mineral concentrate. The global recovery of THM starts to decline rapidly in the fractions finer than 106 μm and the mass disposal (tailing) does not follow in the same proportion. Higher zircon contents in the concentrates of the fractions finer than 150 μm imply a significantly lower recovery of heavy minerals like ilmenite, pseudorutile, and rutile that make the fractions coarser than 150 μm.

Jan 9, 2024

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970