Search Documents

By J. J. Wallace

This report describes the initial phase of Bureau of Mines research in the hydraulic mining of bituminous coal. The mining site and equipment are described, and the test procedures and results obtained with a bar-mounted monitor are given. Tests showed that hard Pittsburgh-bed coal can be mined hydraulically from a solid face at water pressures of 4,000 pounds per square inch.4 Coal was penetrated to a depth of 4 feet in 20 seconds with 225 gallons of water per minute coming from a 3/8-inch nozzle at 4,000 pounds per square inch pressure. Some difficulty was encountered in cutting the binders occurring in the coal; it was not possible Lu penetrate directly the overlying draw slate.

Jan 1, 1961

By F. Ajersch, A. R. Hekmat

Apparent viscosities of hypo-eutectic (Al-7% Al) and hyper-eutectic (Al-35% Si) binary alloys were measured in the semi-solid state using a Couette type viscometer at variable shear rates. Analysis of the microstructural evolution demonstrates the differences in the rate and degree of attrition of the primary phase particles which are characteristic of the thixotropic nature of the semi-solid alloy. It was observed that the Si primary phase in the hyper-eutectic alloy is much more difficult to fragment than the dendritic a-Al phase in the hypo-eutectic alloy. For the case of the a-Al, the dendritic structure is broken down by attrition and fracture of the dendrite arms whereas the fracture of the Si hexagonal crystals in the hypereutectic alloy occurs along the {100} and {110} cleavage planes. Results are presented for fixed solid fractions of the primary phase at isotherm condition for each type of alloy.

Jan 1, 2006

By Lennart Mukka

The Kiruna Mine in Sweden currently has three ventilation systems. The first two (a new and old system) serve the production areas. The third system is used for the facilities on the former main haulage level 775. That area includes offices and workshops for load haul dumpers (LHD) and drill rigs. The third ventilation system also covers the crushing and haulage on level 1045. At the present time, the total airflow for the mine is 1,600 m3/sec(3.4 million cfm). The current system serves the levels above the 775 level. The new one is for the levels between 775 and 1,085 m (2,540 and 3,560 ft), which are needed for the new ore body. When all of the production is below level 775, the old ventilation system will be closed down.

Jan 1, 2002

By James R. Cosby

This report describes work performed for the Bureau of Mines to evaluate available portable instruments for their effectiveness in detecting and locating damaged metallic shields in Types SHD and SHC cables. A second phase of the program is also covered wherein several instruments of a type which show promise are purchased for modification and testing to verify their performance.

Jan 1, 1980

By E. C. Olsen

This paper describes the unusual hazardous conditions encountered in mining thick, inclined coal beds under heavy cover in Carbon County, Utah. This description includes heavy roof conditions, sloughing ribs, steep pitches, and severe bouncing experience. Emphasis is placed on the top bench system of mining and development in the top half of a 16-ft seam, under the roof rock, which is bolted, and the recovery of the bottom coal on retreat; success of bolted roof and ribs; and shuttle car haulage on pitches up to 25%. The use of protective cages for operators of face equipment, the guarding of belt conveyor systems to prevent injury associated with deliberate entry, and the positive lockout of electrical equipment is described and illustrated. Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that in- fluence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25% and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development. MINING PRACTICES Mining has generally been confined to the Lower Sunnyside Seam which measures from 7 to 16 ft in

Jan 1, 1963

By Jeffrey M. Listak

This report describes a study, conducted jointly by BethEnergy Mines Inc. and the Bureau of Mines, to assess the effects of longwall front abutment loading on various supplemental support materials utilized in a predriven recovery room. The purpose of the predriven recovery room is to reduce longwall equipment transfer time by eliminating the premove preparation associated with conventional recovery methods. In addition, the room provides a large area in which face salvage equipment can maneuver. Results of four recovery-room study areas show the progression and influence of the front abutment on the longwall panel and supports and their subsequent behavior. The best performance (i. e. the support that most facilitated recovery) of support material was achieved through the use of a concrete mixture which had a sand content of 35 percent by volume. The longwall transfer time was reduced by 30 percent which translates to a production advantage of 37,000 raw tons of coal per panel.

Jan 1, 1989

By S. Eck

In previous work the influence of the casting speed on the flow field and the shape of the solidification front in an industrial 0.82 x 0.25 x 0.8 m³ bronze caster had been investigated. Both numerical and experimental model represented 1:1 the real caster geometry. A comparison of the results of both numerical and experimental models for the flow during the casting process showed a good agreement in the qualitative velocity fields (flow direction and vortex formation). This work represents a parameter study of the numerical model with variations of the turbulence conditions at the inlet in order to clarify their influence on the flow field in the caster. In order to find the best boundary condition at the inlet, the numerical calculations for water have been compared with the measured flow fields in the water model. The new boundary conditions were then applied to the numerical model of the bronze casting process.

Jan 1, 2009

The epithermal Au-Ag deposits of the Hauraki Goldfield have formed in the convergent plate margin setting of the Coromandel Volcanic Zone (CVZ). The deposits form as siliceous lodes in the upper parts of geothermal systems associated with andesitic and rhyolitic volcanism. Two types of low sulphidation epithermal mineralisation are recognised in these volcanic terranes. Vein deposits within the rhyolitic terrane in the east and south of the CVZ (Whitianga Province) are typified by Chalcedonic Silica-Adularia-Illite type mineralisation. The veins are hosted by both rhyolite-dacite volcanic rocks and the underlying andesitic basement. The mineralisation formed by episodic violent decompressional boiling of deeply circulating meteoric water, with some magmatic fluid contribution; this boiling was associated with hydraulic fracturing and hydrothermal eruptions in geothermal systems where the piezometric surface of the deep geothermal reservoir lay near-surface. Such episodic boiling provides chalcedonic veining, banding and brecciation textures, adularia stability, bladed calcite, and extreme loss of H2S gas from the fluid to cause major gold deposition.   Crystalline Quartz-Illite-(Adularia-Kaolinite) type mineralisation is widespread in the andesitic terrane forming the northern and western portions of the CVZ (Kuaotunu Province). There is a spatial association with weak mineralisation of the high sulphidation (Vuggy Silica-Alunite-Kaolinite-Illite) epithermal type and porphyry eu-Au type. Crystalline Quartz mineralisation is probably formed by the mixing of shallow acidic groundwaters with the ascending deep geothermal fluid in geothermal systems beneath andesitic stratovolcanoes. The piezometric surface to the deep geothermal reservoir in these systems is likely to lie at considerable depth, with acidic gases rising from the geothermal reservoir condensing within the overlying vadose zone. The cooling effect, oxidation and pH decrease accompanying mixing apparently overcomes the dilution effect, and results in quartz deposition, illite (and locally kaolinite) alteration, and precipitation of gold. A high level of base-metal sulphide precipitation also enhances gold deposition. Violent boiling of the mixing fluids may occur at local structural dilation sites, producing high grade "bonanza" gold mineralisation.

Jan 1, 1991

By A. J. Geldenhuys

This paper will focus on two topics, namely (1) an innovative process for the neutralization and partial sulphate removal of acid streams produced during coal mining and processing and (2)optimization of this integrated neutralization process by adding small amounts of synthetic organic polymers. The integrated lime and limestone process has been developed to neutralize acid mine water and to remove sulphate (to less than1 200 mg/l), magnesium and metals. Limestone and lime treatment is the most cost-effective technology for neutralization and partial sulphate removal of acidic/sulphate-rich water to sulphate levels of less than 1 500 mg/l due to precipitation of magnesium and removal of the associated sulphate fraction (through gypsum crystallization). Neutralized mine water of this quality may be suitable for irrigation. The process consists of the following stages: 1. Limestone (CaCO3) neutralization to raise the pH to 7 and CO2-production. 2. Lime (Ca(OH)2) treatment to pH 12 for Mg(OH)2precipi-tation and gypsum (CaSO4.2H2O) crystallization. 3. pH adjustment with CO2recovered from stage 1 and CaCO3 precipitation. Retention times of 1 hour, 4 hours and 1/2an hour were required by stages 1, 2, and 3 respectively. The sulphate level was reduced to 1 094 mg/l, which is less than the original aim of 1 200mg/l. Chemical costs associated with neutralization, using limestone instead of lime, are reduced by 69% in the integrated limestone/lime process. The overflow water from the clarifier of each of the above stages generally contains a wide variety of colloidal impurities that may cause the water to appear turbid or may impart colour. This results in very slow sludge settling rates that cause overflow water with a high degree of turbidity and colour. There are a number of successive or simultaneous stages involved in the agglomeration of particles. To get optimum neutralisation of the acid water and partial sulphate removal to below the saturation level of gypsum (i.e. 1 500mg/l), maximum sludge recovery is needed. The higher the concentration of seed crystals, the larger the surface area. Therefore, effective removal of suspended and colloidal matter from the overflow of each stage is required and can be achieved by coagulation and flocculation. The polymers PAC6 and 3095 were effectively used as coagulant and flocculant respectively. The addition of these polymers resulted in a clear overflow in each of the above stages with a very low turbidity.

Jan 1, 2003

By Jan E. Nesset, Colin Hardie, Peter Radziszewski, Donald P. Leroux

"The successful introduction of new high intensity stirred milling technologies (e.g. IsaMill, SMDetritor) to the mining industry in recent years prompted Noranda-Falconbridge to initiate a study comparing these technologies to the conventional technologies of ball milling and existing vertical stirred mills (e.g. VertiMill). The study was unique in that it utilized the same material (Brunswick Mine zinc cleaner regrind mill feed), the same sizing instrument (a Malvern laser difractometer) and sampling protocol, and media size and type (for the high intensity stirred mills). The paper compares the net energy efficiency (kWh/t) of the various technologies, their power intensity (kW/m3) and product size distribution spread (P80/P20). A key finding is that media size is critical to achieving optimal performance. As part of the performance comparison, an analysis of the four methods of power measurement was made (Prony brake, shaft torque, grinding chamber reaction torque, “no-load” correction) and followed-up with an experimental test procedure using three of these methods. The findings include divergent results for power measurements and some explanations based on the observations are proposed. The direct shaft torque and Prony brake calibration methods are shown to be the methods most suitable for stirred mills.INTRODUCTIONThe motivation for the investigation reported here was the lack of a suitable comparison within the available literature of relative grinding efficiency for the emerging crop of new industrial fine grinding technologies. Such comparisons are potentially fraught with inconsistency, from ore samples and grinding media used, to testing methodology, to size measurement techniques, to the power measurements themselves. The collaboration of the industrial suppliers (at the time MIM Technologies and Svedala, now Xstrada Technologies and Metso Minerals) and McGill University (P. Radsiszewski) were sought in order to ensure as valid a comparison as possible. The work was performed between October 2000 and November 2002, led by the mineral processing group at the Noranda Technology Centre (NTC) in Pointe-Claire, Quebec. The paper is presented in two sections; Part A considers the different power measurement methods and a comparison of the results for the SMDetritor (SMD) technology, while Part B reviews the grinding performance of the 5 technologies investigated using the selected performance criteria."

Jan 1, 2006

By F. E. Diebold

The methodology for describing the geochemistry of elements in a coal seam have been developed. This has been applied to the Rosebud Coal Seam, which is an economically important member of the subbituminous coals of the Fort Union Formation in Eastern Montana. The method development has involved a detailed study of two popular techniques for determining the metal geochemistry of coal, namely, whole coal analyses and coal physical fractionation. The mathematically contrived element associations (whole coal analyses technique) and the element concentration trends in the float and sink fractions (physical fractionation technique) are considered to lead to only qualitative conclusions concerning the chemical associations of the elements in coals. Additionally, the processes taking place with the coal during low temperature ashing in an oxygen plasma are experimentally investigated and shown to be of sufficeint extent that the use of such low temperature ash for deciphering element geochemistry is questionable. The method developed in this study is a chemical fractionation that involves the sequential leaching of coal with water, 0.5 N HC1, 3 N HC1, 2 N HNO3, and 48% HF. These leach solutions are shown to selectively dissolve the predominate inorganic phases, sulfates, Ca and Mg carbonates, Fe sulfides and K alumino-silicates and quartz, respectively. These phases were identified with the use of XRD, SEM, EM and leaches (water and 0.3 N HC1) of whole coal and low temperature ash. The incorporation of the anion-exchange step in the leaching scheme was investigated and was observed to warrant further study of such intensity to be, at the time, unuseable. The use of this sequential leaching technique on several coal samples from the same seam generates element concentration trends that can be quantitatively interpreted with respect to the chemical associations of the minor and trace metals in the coal seam. The properties of the various seams of economic importance in the Fort Union Formation in Eastern Montana are compiled and presented. The subsequent conclusion is that there is not a large variation in the properties of these coal seams and that the variations within the Rosebud are within one order of magnitude. The chemical fractionation technique, investigated in this study, was applied to composite tipple samples of the Rosebud seam. Each composite sample represented 76,800 tons of coal. A minimum of 32% of the Ca and Mg are present as separate water soluble sulfates. An excess of the sulfate ion in the water extracts shows the predominating influence of the ion exchange capacity of the organic compounds in the coal. Based upon the CO content of the coal and the HC1 leachate data, 25 to 30% of the alkaline earth elements exist as separate carbonates and the remainder are associated with the organic compounds. The small fraction of the illite that dissolves in the HC1 and HNO3 leachates accounts for the K and Al. Slight dissolution of the pyrite in the HCl solvent occurs, the small amounts of Li and As do not relate to any known phase and Mn is present as a separate carbonate phase. Fe and a significant amount of the As exist in the pyrite that is dissolved in the HNO. Se is equally partitioned between the pyrite and the organic compound~. Most of the trace elements are found in the HF solutions. Li, V, and Cr were interpreted to be associated with the clay minerals (kaolinite and illite). Ni and Pb appear to be present as separate phases and 50% of the Hg is HF soluble but is not chemically related to any known inorganic phase.

Jan 1, 1983

By A M. Sherwood

The Otago and Southland lignite deposits represent by far the largest known fossil energy resources in New Zealand. Despite their size they have remained virtually untouched since exploration in the 1970s and 1980s defined their extent. In total there is an estimated 10.9 billion tonnes of lignite in 13 defined fields in Otago and Southland. Much of the exploration work only targeted seams at shallow depth and it is highly probable that there are further resources at depth in the fields that have been explored to date.   L&M Lignite Limited (L&M) holds exploration permits over a number of lignite deposits and is currently engaged in pre-feasibility studies to investigate the potential of the lignites for gasification. L&M is focussing its studies on the Hawkdun and Ashers-Waituna deposits. Coal quality in these deposits, particularly Ashers-Waituna, is highly suitable for gasification. In total the two deposits contain 1647 Mt of potentially recoverable lignite. L&M has engaged a variety of consultants to progress this project. The Hawkdun and Ashers-Waituna deposit databases have been re-evaluated and the resources remodelled. Further drilling has been carried out and the coal quality database has been expanded. The baseline project is to develop a mine to feed a plant that will produce liquids, specifically low-sulphur diesel and naptha, using the Fischer-Tropsch process. The project anticipates a staged development of 10 000 barrel per day units, each requiring mining at the rate of 12 700 tonnes of lignite per day. The production of other products including ammonia-urea, methanol, hydrogen and electric power is also under study.

Jan 1, 2005

By P. H. Carr, G. G. Marino, K. A. Patel

Extensions to a correctional institution at Wabash Valley, Indiana, required development over abandoned coal-mine workings, at 90 m depth, where subsidence was possible at surface. Backfilling of the flooded mine in critical areas was determined to be the most cost-effective method of limiting the risk of damage to the buildings. Containment grout was first placed in selected entries and cross-cuts of each mine area; the remaining volume was then filled with a readily flowing infill grout. Where a high proportion of an area was taken up by rubble, calcium lignosulphonate was used as a retarder and plasticiser to increase penetration. Grout movement was monitored from adjacent boreholes with an electrical resistivity probe during grouting, while after the work was finished core samples were obtained from verification holes drilled in the backfilled areas

Jun 19, 1905

By Carlos Maurício Fontes Vieira

In the present work a ceramic body, fabricated using a mixture of clays and sand, for roofing tiles, produced in Campos dos Goytacazes, north of the State of Rio de Janeiro in Brazil, was characterized. Characterization was performed by X-ray diffraction, thermo analysis, chemical analysis, particle size distribution determination and plasticity. In addition, technological properties related to water absorption, linear shrinkage and flexural rupture strength were determined in samples fired at 700, 900 and 1100oC. The results showed that the investigated ceramic body has satisfactory plasticity and presents a refractory behavior during firing due to the predominantly kaolinitic nature of the clays.

Jan 1, 2006

By J. E. Cleveland

The major health concern for uranium miners is the release of radon gas and the resultant ingrowth of the short lived daughters in the mine atmosphere. Present methods of control are the utilization of mine ventilation systems for dilution and control of ingrowth time to maintain working levels below those set by regulations. This study examined pressure cycling efforts on the radon emanation. The mechanical ventilation systems were altered to allow pressure changes throughout the mine to increase radon influx during the off shifts and thus deplete the sources of radon gas. Continuous radon working level and environmental monitors, developed by the Bureau of Mines, were employed to monitor radiation and physical parameters in the mine workings. The mine ventilation system was then varied to induce radon flows during off shifts, thus, depleting the radon sources during normal production shifts. Electro-static precipitators were also tested to determine radon daughter collection efficiencies. Both radon and radon daughter concentrations were monitored and evaluated. Major problems were found in the simple mechanical operation of cleaning these units.

Jan 1, 1982

The phosphorus content of the banded iron formation (BIF) and of the associated iron ore deposits in the north west of Western Australia is known to vary widely, a fact which has considerable econ~mic significance. Trendall and Blockley (1970) have described the variety of textural appearances of apatite in the Hamersley Group BlF, and suggest that apatite may account for the entire phosphorus content of the unaltered BIF.A preliminary investigation using an M.A.C. electron microprobe analyser has shown that, at least in some iron ores and in partially enriched BIF and associated shales, the phosphorus occurrence is more complicated than this. A suite of samples was examined from one location which covered the entire Dales Gorge Member and some adjoining macrobands in the Mt. McRae shale, together with samples selected for their high phosphorus content, degree of ore enrichment, and position relative to the enrichment zone. Calcium apatite was not observed in any sample of ore from this sequence, despite its ubiquitous occurrence in the BIF. Silicate mineralogy in the enriched regions also differs from that in the BIF, but this change has not yet been studied in detail.The phosphorus content of goethite in one orebody is often high and appears to be in solid solution in the goethite structure. It shows little or no variability on a micro-scale within a grain, except where theremay be a zoned enrichment near boundaries and solution channels. There is also a limited solubility of phosphorus in hematite (the maximum observed by the author is 0·1 per cent P); but where the hematite is martitic (after magnetite) its phosphorus content is always low or zero. In some bands, martitic hematite has been hydrated to goethite, and this also has a very low phosphorus content. Phosphorus was not found in the silica or silicates in the ore, and even when iron enrichment is just beginning, a limited suite of samples from the BIF suggests that the phosphorus content of the chert microbands is almost entirely in the microscopic goethite nuclei (after riebeckite) scattered throughout the chert. The ability of goethite and hematite to accept phosphorus...

Jan 1, 1973

By J. Z. Cui

In this paper a statistical multi-scale method for the mechanics parameter prediction of the rock mass with random distribution of multi-scale cracks/joints is presented. First the micro-structure of the rock mass with random distribution of multi-scale cracks/joints is represented. Then the statistical second-order two-scale method for the mechanics performance predictions of the rock mass structure with random cracks/joints distribution is presented, including the statistical second-order two-scale expression on the vector-valued displacement, strain tensor and stress tensor, and the algorithm procedure of statistical multi-sale computation for the mechanics parameters. Finally some numerical results for mechanical parameters for the rock mass with random distributions of multi-scale joints/cracks by statistical multi-scale method are shown.

May 1, 2009

By M. -O. Suk, S. -K. Jo, S. -C. Shim, J. T. Kim, S. -H. Kim, C. -W. Seo, J. -S. Kim

An equilibrium study was carried out at 1873 K to ascertain the effect of carbon in CaO-SiO2-Al2O3-MgO-MnO-FetO slag systems on their FetO and MnO activity coefficients, representing the slag?s thermodynamic potential for steel reoxidation. Both ?FetOand ?MnO showed not only a sharp increment, but also a simultaneous slow decrement by increasing carbon content in slag, suggesting opposite roles of the carbon according to its stable forms. XPS (X-ray photoelectron spectroscopy) was introduced to clarify the stable forms of carbon in slag. XPS results prove that carbon dissolves in slag as carbonate, and carbide ions under oxidizing and reducing atmospheres, respectively. It was concluded that carbonate ions increase ?FetOand ?MnO, and that carbide decreases them. This paper suggests an application method of the present results to actual ladle refining processes, in order to enhance steel cleanliness without decreasing (FetO + MnO) content in slag. Keywords: carbon, slag, activity coefficient, FetO, MnO, carbonate, carbide, XPS, reoxidation, cleanliness

Jan 1, 2004

By L. P. James, W. W. Atkinson

Utah has produced about one billion troy oz. (31.7M tonnes) of silver, more than any U.S. state except Idaho. Several very high grade ore systems, now closed, occur within large polymetallic limestone-hosted districts related to plutonic complexes. These Utah mines fed several major lead smelters for nearly a century. Interaction of magmatic chloride-rich fluids with carbonate rocks localized significant bonanzas within these districts. A low sulfidation state was produced in the fluids by their passage through limestones. The Bingham porphyry mine has also yielded more byproduct silver than other porphyry copper-gold systems. Away from exposed intrusive rocks, some large silver-only systems occur in Mesozoic sandstone and in caldera-related veins in volcano sedimentary rocks. Thick permeable latest-Proterozoic basement meta quartzite sequences present beneath western Utah may have been important, as perhaps they were in the Coeur d’Alene district of Idaho, in providing chloride and silver-rich ore fluids. However, it is clear that specific Tertiary magmatic events played an essential role in the evolution of the Utah silver-rich metallogenic province. The largest silver districts in the state are genetically related to porphyritic plutonic rocks.

Jan 1, 2000

By Alfred W. G. Wilson

THE ultimate purpose of the Chemical Manufacturer is to produce consumer products which can be sold to customers. Such production and sales can be continued only if the operations yield a profit to the manufacturer and if the products meet the requirements o the consumer--bath parties to the transaction must be satisfied. There are vast numbers of consumer products, made by chemical pro-cesses. The production of some of these ultimate products may involve the use of several intermediate chemicals, applications of few or many different processes, and the utilization, somewhere in the series of operations, of a variety of raw materials. On the other hand, some ultimate products have a very simple chemical history between raw materials and end products. There are no chemical products in use which are completely independent of the mineral industry. For many, the association is direct and obvious; for others, it may be indirect and even obscure. Analyses of the process and raw-material ancestry of a very large number of consumer products would suggest that many products are derived from Industrial Mineral products directly, that there are many in which the connection is indirect, and that there are only a few products with which industrial minerals are not in some way or other associated. The vast majority of the more important chemical products, and especially the basic chemicals from which other products are made, are directly dependent for their production upon Industrial Minerals or their derivatives. In the preceding part of this paper, for each raw material mentioned some references have been made to the leading chemical products based on this material. This, however, is only part of the story, because in most cases the consumer product can be made from any special raw material mentioned only by the use of other materials or chemicals made from them. The production of consumer chemicals is really possible only through an intricate interlocking of processes, materials, and apparatus.

Jan 1, 1940