Search Documents

By G. E. McElroy, A. S. Richardson

"The Bureau of Mines, in cooperation with the Anaconda Copper Mining Co., has conducted a series of experiments an air measurement in fan-pipe installa¬tions in a Butte mine during the fall and winter of 1922-3. The chief purpose was to determine the friction factors for different types and sizes 3f fan piping, but much attention was devoted to methods of air measurement, not only with respect to the methods used for friction factor tests, but also to com¬parison with other methods.The air flow was measured simultaneously at two points 380.6 feet apart in six different fan-pipe installations, each over 500 feet in overall length, in a rock cross cut adjacent to an air shaft,The air pressure was regulated by two sinoco multivane fans, driven by 7 ½ h.p. motors, the fans being connected in tandem so that one discharged into the intake of the other through a short connector and the latter discharged into the line through a straight connection equipped with a honeycomb of 4-inch squares or S radial vanes to prevent spiral flow of air, At each point where it was desired to measure the air flow, measuring sections equipped with piezometer rings pierced for easy insertion of pitot tubes, thermometers, etc. Piezometer static pressures were used in all the tests as standard, and dynamic or total pressures only were obtained with the pitot tubes, except for purposes of comparison.The tubes had special guide blocks, designed especially for underground work. To insure greater accuracy two tubes were used simultaneously, in order to obtain the velocity pressure at the center of the section simultaneously with that nearer the circumference, so that the mean velocity would be determined as accurately as possible. The tubes were held in proper place by means of flat guide boards. Velocity pressures were measured in manometers."

Sep 1, 1923

By Richard Harrison, Frank Lim

Deepsea Mining will soon become a reality with Nautilus Minerals getting their equipment ready to mine SMS at Solwara 1 off the coast of Papua New Guinea. The vertical transport system (VTS) adopted by Nautilus consists of a riser hanging ‘freely’ from the mining production vessel with a lifting pump unit suspended at its lower end. A compliant jumper connects the pump to the seabed crawler without restraining its movements. In this free-hanging VTS arrangement, the vessel can be re-positioned to follow the crawler should it want to extend the mining area and start stretching the jumper. A recently proposed alternative to this is a free-standing VTS whereby the riser is grounded on the seabed with a base and maintained in an upright position by distributed buoyancy modules or a buoyancy tank at the top. A compliant jumper connects the seabed crawler to the riser base, and another connects the riser top to the vessel. In this free-standing arrangement, the entire VTS can be lifted clear of the seabed for relocation to a new mining area. This paper will describe the important features of the two options and discuss the advantages and disadvantages in respect of riser dynamic behavior, water depth, weather and mining windows, pump maintenance, installation and retrieval, continency measures, etc. The two systems will also be appraised separately for mining SMS and SMnN deposits.

Jan 1, 2018

By Claudio Pereira Diogo

Bobinas de aço laminadas a frio galvanizadas com recobrimento do cromo foram empregadas para a produção de telhas e calhas d’água. Entretanto, o fabricante destes produtos teve problemas com as superfícies obtidas, que mostraram sinais de marcas de deformação/estiramento. O problema é que, na aplicação desejada, uma aparência superficial que não seja brilhante e lisa é muito indesejável. Este trabalho foi feito a fim de descrever as condições que levaram o material para se comportar como visto pelo usuário (fabricante de telhados e calhas de chuva) com base em sua aparência e comportamento mecânico. Foram empregadas observações em microscópio estéreo e curvas tensão-deformação, obtidas a partir de ensaios de tração. Com base nos resultados, são apresentadas algumas opções para minimizar a ocorrência de marcas citadas durante a utilização do que as bobinas.

Aug 16, 2017

By Leandro Mendes Pinto

Este artigo apresenta um estudo de analise da viabilidade da substituição de 1 motor padrão utilizado em uma torre de resfriamento por 1 motor de alto rendimento Premium acionado por um Inversor de frequência interligado ao controlador de temperatura. Nas Torres de Resfriamento, ao implantar uma solução que pode a variar a velocidade dos ventiladores de acordo com a temperatura ambiente e a exigência de resfriamento do processo, pode-se obter grandes ganhos em economia de energia. Neste cenário, os motores elétricos têm papel determinante pelo amplo uso na indústria devido a sua versatilidade e eficácia. Por isso, melhorias e inovações são sempre necessárias para otimizar processos e aumentar a lucratividade.

Sep 25, 2017

By Toshiro Kuji, Masakazu Fujita, Tetsuji Saito

"The magnetic properties of the magnetic materials were deeply dependent on the microstructures. In this study, the novel technique to produce the desired microstructures in a controlled manner was proposed. The technique consisted of the production of the amorphous alloys and the control of the crystallization process. The technique was applied to improve the magnetic properties of Nd-Fe-B permanent magnets. The microstructural control of the magnets exhibited the excellently high energy-products of higher than 430 kJm-1. The relationship between the magnetic properties and the microstructures of the Nd-Fe-B permanent magnets was discussed.IntroductionThe intrinsic properties of the materials are basically determined by the properties of the constituent elements or the compounds. However, it is often noticed the difference between the observed properties and the theoretical values expected from the intrinsic properties of the materials. This indicates that the observed properties of the materials are determined not only by the properties of the constituent elements. In other words, the observed properties of the materials are also strongly dependent on the morphology of materials. This means that the microstructural control may creates a great improvement of the properties of materials.In Nd-Fe-B permanent magnets, the superiority arises from the uniaxial intermetallic Nd2Fe14B compound which has a large saturation magnetization and a high anisotropy field [1,2]. The magnetic properties of the Nd-Fe-B permanent magnets are dependent on the microstructure, that is, the size, shape and degree of the crystallographic alignment of the Nd2Fe14B phase. Currently, the Nd-Fe-B permanent magnets have been produced by either sintering or melt-spinning [3,4]. In the sintered magnets, alignment of the Nd2Fe14B phase is achieved by the prior green compaction of the crushed ingot powders in an applied magnetic field [3]. In the melt-spinning approach, alignment of the Nd2Fe14B phase is achieved by hot deformation [5]. Amorphous melt-spun ribbons are comminuted and then are consolidated into bulk form by hot pressing before hot deformation. As-hot-pressed magnets have randomly oriented Nd2Fe1~ grains [6]. Subsequent die upsetting of as-hot-pressed magnets gives rise to the crystallographic alignment of the Nd2Fe14B phase."

Jan 1, 1998

By R. M. Damodaran

The flotation performance of Florida phosphate rock was evaluated in terms of the mixing behavior of reagents with particulates during anionic conditioning of phosphate slurries. The various conditioning variables that influence mixing, namely, solids loading, agitation speed and the conditioning time were investigated to determine their effect on reagent coating on the particles. The phosphate recovery was used to monitor the conditioning efficiency. The mixing characteristics of the phosphate feed were evaluated in terms of the ratio of the mixing power P, to the minimum power Pm' required to keep the slurry in suspension. It was found that mixing conditions govern the conditioning time required to obtain high recovery. Reagentization was slower at lower P /P m ratios. At higher P /P m ratios, the flotation recovery was optimized and the agitation speed was found to have no significant effect on it. Optimum mixing conditions were obtained for a 74 wt% slurry at an agitation speed of 450 (47 rad/s) rpm. Under the optimum conditions of mixing, recovery was improved at low collector dosages and short conditioning times.

Jan 1, 1995

By Dhyemila de Paula Mantovani

Hoje em dia, a necessidade de utilizar materiais ecologicamente corretos tem aumentando em paralelo com a constante busca de novas tecnologias para produzir materiais renováveis, economicamente viáveis e tecnologicamente avançados, o que justifica esse trabalho. O presente trabalho consiste em estudar o comportamento mecânico de compósitos de matriz poliéster reforçados com fibras de cânhamo e testadas com impacto Izod. Para a realização deste teste, foram feitas amostras com dimensões de 10 mm de largura, 63 mm de comprimento e 12,7 mm de espessura em diferentes frações volumétricas de fibra, 0%, 10%, 20% e 30%. As amostras foram testadas em um conjunto pendular PANTEC na configuração Izod, modelo XC-50 localizado no LAMAV/UENF. A energia de impacto Izod dos compósitos de poliéster de 30% de fibras de cânhamo foi de 169,4 J/m.

Oct 30, 2017

By Matheus Tocchini, Henrique Kahn, Juliana Antoniassi, Carina Ulsen, Eldon Masini

"Sand and gravel are the second and third largest minerals in production in Brazil, and this is increasing noticeably. The extraction of natural sand from river beds is increasingly restricted and most of the sand used in large cities comes in from more than 150 km away, resulting in high transportation costs. As a result, it has become more common to use crushed rock as artificial sand. The main difficulties in this process are controlling the shape of the particles and the content of deleterious materials, such as mica. Within this situation, this paper presents an alternative to using artificial sand for concrete use. Our procedure involves the following steps: a) sampling sand from different production days, b) characterizing the bulk sample by particle size and shape distribution, chemical composition by X ray fluorescence and mineralogical composition by X ray diffraction, c) removing fine grains by air classifier, d) performing intensive attrition with high pressure washing and e) characterizing products. The results demonstrated that this sample contains a huge proportion of fine grains and a notable content of mica, which is distributed along all sieve fractions. The presence of mica makes the use of sand in concrete unfeasible, moreover scanning electron microscopy analysis demonstrated that this phylossilicate is finely grained and associated with coarse fractions. Thus, the removal of fine fractions made possible a partial reduction in mica content. Furthermore, intensive attrition demonstrated that the procedure was efficient to remove most of the mica while also reducing sharp edges, which improved the shape of these particles."

Jan 1, 2014

By Nagy El-Kaddah

One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100µ inclusions are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate ?the capability of the system for producing super-clean metals.

Jan 1, 1996

By David Bassanelli Sampaio

Com a crescente demanda por sistemas distribuídos e multiplataformas, houve uma larga proliferação de métodos, linguagens e tecnologias com o objetivo de atender aos mais diversos requisitos desse ambiente. Com isso, a TI de corporações que possuem desenvolvimento interno de aplicações enfrentam um grande desafio de gerir conhecimento dos profissionais mais experientes e integrar novos profissionais de forma a garantir a qualidade e agilidade na tratativa de incidentes, bem como a capacidade de evolução e criação de novas soluções. Neste trabalho, apresentaremos as diretrizes, tecnologias e processos desenvolvidos na Usiminas, consolidados em uma arquitetura. Esta arquitetura propiciou, entre outros, a estabilidade e continuidade dos sistemas existentes, a padronização da experiência final do usuário, a agilidade na construção das soluções Java, evoluindo a qualidade dos sistemas mantidos pela TI, com resultados efetivos.

Oct 30, 2017

By D. Minney

The quality of resin used in South African collieries is currently controlled according to South African Bureau of Standards, "SABS-1534:2002". It has however been found that resin which passed the SABS tests failed in underground short encapsulation pull tests. An investigation was therefore conducted to determine the characteristics of resins that are currently being used in collieries. A series of in situ short encapsulated pull tests was conducted to determine the effect of expired resin on support performance. The results showed that the longer the time after the expiry date the poorer the resin performance. A series of resin-torque tests has been performed using Anglo Coal's testing facility. The following parameters were investigated on different resins: Spinning speed, Mixing time, and Setting time. An attempt was also made to develop a new quality control procedure for resin. This procedure enables mining personnel to make sure that the quality of resin can provide the required support performance. The effect of spinning speed on resin performance was also investigated. The results showed the resin gelling times of resin decreases as the spinning speed increases. It is found that over-spinning with slow speed roofbolters may result in decreased bond strengths. It was found that a 30-second resin (10-second spin, 30-second hold) should never be spun more than 20 seconds, even with very slow roofbolters (100 rpm).

Jan 1, 2005

PRESIDENT MARKS: We have a letter from Mr. Frank N. Cameron, of the Utah Fuel Company, that perhaps I had better read to you. It is addressed to Mr. Shubart, Rocky Mountain Coal Mining Institute (hands letter to Secretary Shubart). UTAH FUEL COMPANY MINE SUPERINTENDENT Castle Gate, Utah, February 9, 1926 Mr. F. N. Cameron, Vice-President & General Manager, Salt Lake City, Utah. Dear Sir: It has now been about nine months since we started the system of having the fire bosses take charge of all shooting and gas inspections at the Castle Gate Mines. We had considerable trouble when we started. Like all other new systems which have been installed, this one was hard to get started and was criticised both by the miners and officials in our own organization, as well as by other organizations in the mines of this county. The older the official and miner was the stronger they seemed to be opposed to the new method. They have no arguments to offer against it, but they know it is not right "because their grandfather did not work it in that way." We know that when some of the other systems were started in the mines of this county, they were fought from all angles. The electrical shooting almost brought the miners at Sunnyside out on strike; their main argument was that they could not make a living if they had to obey the rules that the company was trying to enforce. They also claimed that they could not make enough coal for the day's work by only shooting once at the end of the shift. The same applies to the sprinkling the miners claimed that they would all die of some disease if they were forced to work in a sloppy, wet mine every day. The mining machine was another thing that was hard to install the miners claimed that the company was trying to rob the Door miner out of a chance to make living by installing mining machines to cut the coal. I do not think that the system we have at our mines is perfect-there is still room for improvement in the shooting and inspection of the mines, but I do really think that for safety and efficiency, the inspection department at our mines, working under the new system, is as good if not better than any other inspection department working under the old method in the other mines. I am giving some of the arguments in favor of the new system and would like to hear the arguments against it-if there are any. In cutting the men from monthly to day wages, I do not think it is only the company that benefits by the arrangement, but the fireboss is the one that gets the best of it by the change. How often have we heard the fireboss complain of the hours he had to put in just because he was a monthly man? Under the new wage scale he is paid for every hour he puts in the mines, and when the mines are working every day he makes considerable more than when he was being paid a monthly salary. When the mines are working slow, there is generally some work that has to be done on idle days, or in slow times the force could be cut to a point where some of the work could be done on idle days, and thus the fireboss could be given the preference in this extra work and in this way, his wage could be kept up to the standard monthly salary he was getting before. Under this arrange-

Jan 1, 1926

By F. E. Block, Robert R. Brown, A. W. Henderson

The chlorination of Cr₂ 03 (chromic oxide ) in the presence of carbon with CC14 (carbon tetrachloride ) and COCl2 (phosgene ) chlorinating agents was investigated by employing the radioactive tracer carbon By tagging carbon mixed with Cr₂ 0з , the chlorination reaction was evaluated in terms of the competitive reaction of the elemental carbon and the carbon contained by the chlorinating agent . A unique gas - analysis train was used to separate the chlorination product gases ; CO , CO₂ , and COC12 . The C¹ activity of the gases was determined and used to calculate the reactivity of each source of carbon . Reactivities were determined for the temperature range from 600 ° to 900 ° C. The results of the investigation show that each source of carbon reacts significantly with the Cr2 03 and that the reactivity of each form of carbon depends on the reaction temperature , and each form is independent of the other . Radioisotope and gas - analysis techniques are discussed and a description of the experimental apparatus is given .

Jan 1, 1964

By J. D. Price, W. M. Bertholf

One of the chief difficulties with which the operator of a coal washing plant has been forced to contend is the handling of the very fine coal. First he has the problem of separating the fine coal from washery water. This is usually accomplished by the use of settling cones or Dorr thickeners: in either event the separated fine coal contains a high amount (40 to 80 pct) of water and, somewhat loosely, dependent upon the size of the coal particles present, may be known as sludge or slurry. His second problem is the satisfactory further dewatering of such separated sludge and/or slurry. At the coal washing plant of the Colorado Fuel and Iron Corp., washed coal from the Deister Plat-O tables is sluiced to a stationary inclined de-watering screen provided with 3/16 by 1-in. slots, and the coarse coal passing over this screen is conveyed by a Baum-type elevator and a flight-type distributing conveyor to a battery of Carpenter centrifugal driers. The fine coal and water passing through the openings of the primary dewatering screens, plus the fine coal passing through the screens of the centrifugal driers (and no small portion of which is the result of the disintegrating action of these driers) is pumped to two 30-ft Link Belt settling cones. The sludge recovered as underflow from these cones was formerly dewatered on stationary screens having 1/16 by 1-in. slots and discharged on top of the coarse washed coal in the Baum drainage conveyor; but after a relatively few hours of op eration the circulating load of fine coal on this conveyor built up to a point where it became necessary to reduce the quantity of feed to the washing tables. The original arrangement of our coal washing and dewatering equipment is shown in Fig 1. In order to regain the loss in active throughput which had been caused by this circulating load, an installation of six vibrating filters was made during the year of 1936. This resulted in an increase in normal tonnage of washed coal from 1430 to 1750 tons per 8-hr shift, a gain of slightly over 22 pct. This increase in throughput has made a very substantial decrease in the " conversion cost" per ton of washed coal. Since the vibrators were installed, we have gained about 2,000,000 tons in production, compared to what would have been produced in the same number of shifts at the former rate. Putting it in slightly different form, we have saved in the past 12 yr the cost of 1400 operating shifts in the washery. Fig 2 shows the location of the vibrating filters as applied to the original flowsheet. It will be noted that the sludge from the bottom of the settling cones is passed through a distributing box and thence to the filters. The de-watered coal from the filters is de-livered to the conveyor receiving the dried coal from the Carpenter driers.

Jan 1, 1950

By Gislan William Guimarães

Neste trabalho avaliou-se o efeito de diferentes ciclos térmicos na microestrutura e propriedades mecânicas de um aço Dual Phase revestido por imersão a quente, da classe de resistência de 800 MPa, a partir de simulações em escala piloto no equipamento HDPS (Hot Dip Process Simulator), ensaios dilatométricos, tração à temperatura ambiente e flangeamento. Nas simulações de recozimento contínuo foram experimentadas duas temperaturas de encharque no recozimento intercrítico (740°C e 780°C) e três temperaturas de patamar isotérmico no resfriamento rápido (610°C, 560°C e 510°C). A caracterização microestrutural evidenciou que a temperatura de encharque de 740°C não foi suficiente para dissolução completa dos carbonetos formados na laminação a quente, resultando em frações reduzidas de segundo constituinte. Com isso, o limite de resistência mínimo de 800 MPa não foi alcançado. Além disso, os resultados de ductilidade e flangeamento se mostraram aquém dos obtidos nas simulações com encharque a 780°C. Nas simulações com temperatura de encharque a 780°C e isotérmicas de 510°C e 560°C no resfriamento rápido foi atendido o limite de resistência mínimo, com capacidade de expansão de furo ligeiramente superior à obtida nas simulações com encharque a 740°C.

Aug 16, 2017

By John S. Carman

Our industry is in trouble. Real trouble. It has never been an easy, secure business. But to-day it is engulfed in revolutionary currents. No longer can there be reliance upon the checks and balances of market forces. Supply and demand largely dictated the economics of business enterprise in simpler days. To-day politics, in particular nationalism become increasingly dominant. And as governments expand and put out tentacles of interference in the direction of the mining industry, far too little understanding is evidenced as to how that industry works. Then there is something which is relatively new -stagflation. As the prices of minerals falls, the capital investment required for new extractive facilities soars at rates which far outdistance those which are cited by governments to indicate the magnitude of inflation. To illustrate; 1) In 1971 it was calculated that $355 million would be required to bring the Cuajone property in Peru into production. Five years later that stage was reached at a cost of $680 million. 2) With the Caridad mine in Mexico, estimated capital investment doubled between 1971 and 1976. 3) The requirements calculated for Cerro Colorado in Panama have risen in two years from $560 to $800. 4) The budget of $240 million for Sar Chesmeh in Iran in 1971 had become $500 million by 1976.

Jan 1, 1977

By X. Tang, N. Ripepi

The Langmuir model has been widely used for the coal-methane sorption process through an isothermal test. However, even though the temperature-dependent Langmuir model was recognized theoretically and experimentally, the quantitative relationships between the Langmuir constants a and b and temperature have not been clarified and confirmed by laboratory test data. This paper collects 158 methane-coal sorption data under different temperatures that apply the Langmuir model to the relationships between the Langmuir constants a and b and temperature. Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters a and b. The results from these published isothermal tests indicate that (1) there is no consistent relationship between Langmuir constant a and temperature, (2) the Langmuir model is a temperature-dependent model whose temperature-dependent feature is mainly shown by the relationship between the Langmuir constant b and temperature, and (3) the relationship between the Langmuir constant b and temperature can be described by both exponential and linear relationships with dried coal. This paper provides a database for the temperature-dependent Langmuir model that can be used for the reservoir simulation of coalbed methane reservoirs and for the coal seam degasification modeling of underground coal mines, considering the heating effects induced by geothermal and heat injection through factors such as hot water, hot steam and ultrasonics.

Jan 1, 2016

By Breno Totti Maia

Metalurgistas e pesquisadores de aciarias a oxigênio buscam dia após dia o desenvolvimento de parâmetros operacionais com reflexos diretos em ganhos metalúrgicos e no desempenho dos equipamentos, visando aumentar a produtividade e evitando interrupções para manutenção. O principal requerimento para um converterdor a oxigênio é o conjunto de lança com bico de cobre. Recentemente a Lumar Metals apresentou cartuchos com a tecnologia Slagless que podem ser usados para substituir os bicos convencionais de cobre com expressivos resultados de processo. Alguns pontos são fundamentais para se obter um projeto de bico que tenha satisfatória vida útil, como por exemplo, a estrutura do material utilizado, o correto dimensionamento do circuito de refrigeração e o correto dimensionamento dos lavais de saída do oxigênio. O objetivo do presente trabalho é avaliar os efeitos dos parâmetros de processo: pressão e vazão e suas influências no desgaste do bico de lança devido ao mau dimensionamento dos lavais ou quando operando em condições abaixo da especificada. Os resultados mostram que para cada conversor com um perfil operacional único, o projeto do bocal específico é o que garante os melhores ganhos metalúrgicos e aumento da vida útil do bico.

Aug 16, 2017

Jan 1, 1880

By Carolina Person Maschio

Pelotas compostas de minério de ferro, aglomerante e coque foram analisadas quanto à resistência à compressão (a frio e após aqueciemento) e porosidade. Para isso, três lotes de pelotas foram confeccionados, com diferentes teores de redutor, até a quantidade necessária para reação completa com os óxidos de ferro. Após seu preparo, as pelotas passaram por diferentes tempos de cura ao ar. Ensaios de resistência à compressão à frio e porosidade foram realizados em pelotas verdes e com 3, 7, 14, 21 e 28 dias de cura. Após 28 dias, uma série de pelotas foram secas e submetidas a testes de resistência à compressão após serem aquecidas a temperaturas entre 200ºC a 900º. Analisou-se, também, a perda de massa em cada patamar de temperatura. Entre os principais resultados, verificou-se que o comportamento mecânico de pelotas autorredutoras é melhorado com o aumento do tempo de cura e prejudicado pelo aumento do teor de coque e aumento da temperatura. Após 600ºC, a resistência das pelotas cai potencialmente. Além disso, lotes com maiores teores de coque apresentaram maiores valores de porosidade, sendo que este aumento foi mais significativo nos primeiros dias de cura.

Oct 30, 2017