Search Documents

A symposium on the health hazards of respirable dust in the mining and milling of talc was held on May 8, 1973, in Washington, D.C. The results of medical effects on both human and animal subjects were presented. Methods for identification and classification of talc minerals were also presented. Analytical techniques discussed included X-ray diffraction, scanning electron microscope observation, electron probe, and optical microscopy.

Jan 1, 1974

By Dr Karsten Galipp, Kai-Julian I. Hendler, Prof. Manuel G. Pinheiro, Dr Peter J. Bourne-Webb

With a share of approximately 11% of global greenhouse gas emissions, the construction industry contributes significantly towards climate change. This is why construction projects should not only be assessed on costs and technical solutions, but also on their carbon emissions. Life Cycle Assessment (LCA) is a tool which can quantify the environmental impacts of a construction project over its entire lifetime. The objective of this study was to determine the carbon footprint of three types of quay wall structures, namely sheet pile combi-walls, open piled decks and caissons using an LCA approach. Each of these quay walls were studied under the same boundary conditions, such as design life, ground conditions, dimensions, location and so on. The analysis showed that the sheet pile wall has the lowest carbon footprint whereas the open piled structure has the highest. Furthermore, it could be shown that the largest share of greenhouse gases (approximately 80%) is emitted during the production of construction materials. The transportation of materials and construction activities each contributed under 12% to total emissions. The sensitivity analysis showed that with innovative approaches, such as adapting the concrete mix design, the carbon footprint could be reduced by 26% to 40%.

May 1, 2022

By T. Hart

Nuclear gauging is used world-wide in almost every industry. From mining and ore-grading to finished product, the metallurgical industry is one of the biggest users of nuclear sensors for inventory, process control, and quality assurance. This paper will discuss the basic theory of gamma transmission gauging techniques found useful in mining, milling and metal production. Techniques to be discussed are gamma transmission for level and density. A major new technique will also be discussed. This technique is called gamma backscatter. The uniqueness of this technology, how to apply and the differences between transmission and backscatter will be accentuated.

Jan 1, 2011

By Balasivanadha Prabhu, Prasad P. Shanmugasundaram, Narayani Narasimhan

"The grain refinement and mechanical properties of 6061 aluminium alloy produced by equal channel angular pressing (ECAP) have been analyzed in this present study. A innovative triple shear ECAP die was developed for the processing.It was observed that the grain refinement takes place for greater number of passes. It was also found that reducing the process temperature gives fine grain and high microhardness and hence improved propertiesIntroductionTechnological changes in manufacturing industries have depended heavily on development in materials processing and process technologies. Modem industries need high performance materials for severe service conditions. Hence, it is necessary to improve required material properties to achieve better performance and greater service life. As mechanical properties of the materials strong! y depend on grain size ( d) - Hall-Petch relationship [ 1-4], the ultrafine grained (UFG) materials offer superior mechanical properties based on the above relation.Synthesising massive nanocrystalline materials presents a challenge to basic research as well as to application-related processing efforts. Production of ultrafine gram microstructures in metals and alloys having different crystal structures but always an initially coarse microstructure using severe plastic deformation can significantly enhance the physical and mechanical properties of materials. Severe Plastic Deformation (SPD) is an efficient method to induce ultra fine grained structure in materials by deforming it to large strains. Traditional techniques for introducing deformation of higher strains, such as forging, extrusion, drawing or rolling do have the inevitable limitation on required equipments of exerting enough load or pressure to cause uniform nanometer level grain refinement."

Jan 1, 2011

RICHARD R. HICE, Beaver, Pa. (written discussion *).-The matter of selective. mining is probably of more importance in Pennsylvania than is washing, and perhaps washing would not be necessary at some plants where now practised if proper care were taken in the mining. I have in mind one plant where the sulfur content of the entire bed is more than 2 per cent., yet if the bottom 12 in. and the top 12 or 15 in. are separated, the main portion of the bed, some 6 ft., will not contain more than 1.25 per cent. sulfur; and yet in this mine the entire bed .is worked together, the resultant coke, as a matter of course, not being fit for use in iron smelting. Not sufficient notice is taken of the "Double-thick" Upper Freeport coal in Allegheny and Butler counties. This is a very valuable deposit. Other areas where there is a, top member of the Upper Freeport coal are also known, which add to the value of this bed as a coking coal. This double Freeport coal is especially suited for byproduct coking. I cannot be as optimistic as regards the "low-sulfur" Pittsburgh coal in Greene county as the authors. If the term low-sulfur is to he confined to coal with not exceeding 1.25 per cent. sulfur, there is probably little

Jan 10, 1919

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, the U.S. Mine Safety and Health Administration (MSHA) began requiring the use of continuous personal dust monitors to monitor and measure respirable mine dust exposures to underground coal miners. Mines are currently using the PDM3700 personal dust monitor to comply with this regulation. After the PDM3700’s implementation, mine operators discovered that it interfered with proximity detection systems, thus exposing miners to potential striking and pinning hazards from continuous mining machines. Besides the PDM3700, other electronic devices were also previously reported to interfere with proximity detection systems. MSHA sought the aid of the U.S. National Institute for Occupational Safety and Health (NIOSH) and mining industry stakeholders to determine how the PDM3700 and some other electronic devices and proximity detection systems interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments and conducted laboratory evaluations. Some interferences were observed to be caused by electromagnetic interference from some electronic devices, including the PDM3700. Results showed that there was no significant interference when the PDM3700, as well as other electronic devices, and the miner-wearable component of the proximity detection system were separated by distances of 15 cm (6 in.) or greater. In the present study, it was found that the PDM3700 and the personal alarm device needed to be at least 15 cm (6 in.) apart in order for them to be used simultaneously and reduce potential interference. IntroductionUnderground coal miners are exposed on a daily basis to a variety of hazards, such as coal dust exposures, high noise levels, roof and rib falls, potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is that of operating or working near a continuous mining machine. According to U.S. Mine Safety and Health Administration (MSHA) statistics, 44 miners had been fatally struck or pinned by a continuous mining machine since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating continuous mining machines in underground coal mines, with the exception of full-face continuous mining machines, by 2018 (MSHA, 2015a)."

Jan 5, 2018

By Lawrence F. Rooney

One of Edgar Allan Poe's stories that haunts my subconscious is the Masque of the Red Death. These days, whenever I join a group like this, especially during the cocktail parties, I see myself and others as those mythical swingers seemingly isolated from the plague. The world, but this country especially, has had a ball plundering, spending, and wasting its natural resources for 100 years. And, as in days of yore, it is fitting that we end this ball with spectacular fireworks: trips to the moon, so that our grandchildren, huddled in their caves along the Ohio, will better understand how it all began.

Jan 1, 1970

By Natália Cristina Candian Lobato

A indústria siderúrgica gera cerca de 600 quilogramas de resíduos por tonelada de aço bruto produzido. Estes resíduos, conforme estabelecido pela legislação ambiental vigente, devem ter uma destinação final adequada de forma a não acarretar poluição do meio ambiente. Além disso, a preocupação com a sustentabilidade e a escassez de recursos minerais não renováveis tem feito com que as usinas siderúrgicas invistam cada vez mais no desenvolvimento de meios de produção mais econômicos e menos poluidores e na busca de métodos adequados para a reciclagem ou a reutilização dos resíduos gerados, de forma a minimizar a quantidade de resíduos estocados ou destinados a aterros industriais. Neste contexto, destaca-se a escória e a lama de aciaria LD. Assim, este trabalho, avalia as possíveis tecnologias aplicáveis ao gerenciamento ambiental destes resíduos, apontando as tendências e as alternativas tecnológicas para seus tratamentos, de modo a contribuir para o aumento da sustentabilidade deste setor industrial.

Jul 30, 2018

The mining industry, both here and internationally, is continually developing increasingly sophisticated software to compute mineral resource estimates, but these processes cannot compensate for a flawed geological interpretation of the geology of the economic commodity(s) concentrations. Quality assurance and quality control (QA/QC) is becoming increasingly common in association with the sampling and assaying practices within the industry. However, it is rare in the case of a geological interpretation associated with mineral resource estimation. Why? In the context of this paper, QA/QC relates to the use of statistical and graphical tools to show that the geological economic commodity concentrations have been appropriately domained. Domaining is essential to improve the chance of getting a mineral resource estimate right. Commodity value and acceptable concentration variation within a mineral resource can be ingredients that make mineral resource estimation difficult to get right. But it is possible to get it right a very high proportion of the time. It is more likely to occur when inappropriate data consolidation is minimised. In any case, inappropriate data consolidation is significantly reduced when the geological interpretation is strongly consistent with the data and it is demonstrable. To achieve quality global estimates of geological domain concentrations, it is essential that the geology of the prospect is understood sufficiently that the deposit is appropriately domained. Appropriate domaining occurs when sample populations are separated in such a way that only data in harmony with each other within the population contributes to the domainÆs concentration estimate. The paper will use four brief case studies to illustrate how QA/QC can be used to display data and validate the underpinning geological interpretation through its associated domaining to get it right when it comes to a mineral resource estimation.

Jan 1, 2007

By R. L. Clayton

The Bagdad district is 67 kilometers west of Prescott, Arizona, (Figure 1). The area north of the Old Dick and Bruce Mines was originally mapped by Anderson, Scholz and Strobell between 1943 and 1945, (1). The region is perhaps better known for the Bagdad porphyry copper deposit of tertiary age. However, 2 to 5 kilometers south of this deposit are several small massive sulfide occurrences in a eugeosynclinal Precambrian greenschist environment. More specifically, in. the Bridle formation of the Yavapai schist series. Three of these mines - Old Dick, Bruce and Copper Queen - were mined by Cyprus Mines Corporation between 1957 and 1977, and produced nearly 2mm tons of 3.6% copper and 12% zinc. These deposits occur at the interface between andesite and rhyolite and are stratiform in character. Certain structural and textural properties of the Bruce orebody suggest that remobilization of the massive sulfides occurred at some period during the metamorphic history of the area.

Jan 1, 1978

By A. W. Jolliffee

ANY attempt to forecast the mineral resources of a largely unknown region is hazardous and, in the case of the Northwest Territories, such a task is even more hazardous than usual. This is not merely because of the immense territory involved (over a million and a quarter square miles), only a small fraction of which has ever been explored or prospected, but also be-cause both the geology and mineral deposits thus far examined show many unique features, and, finally, because the region is being actively prospected at the present time. However, in view of the present widespread interest in Canada's mineral resources, a brief compilation of what is known regarding mineral occurrences and geology in the explored parts of the far north seems timely. From these assembled data, a few inferences are warranted as to future mineral production from this region. HISTORY The story of mineral discovery in the Canadian northwest is a fascinating one. As well, it abundantly illustrates the importance of mineral occurrences in indicating future mining possibilities. The same sequence of events has repeated itself too often to be merely fortuitous.? In most cases, the dis-covery of a mineral deposit of possible economic value has been foreshadowed by the finding of the valuable mineral or an associated mineral in the same district, generally in small quantity, by an early explorer or traveller. Thus, John Franklin reported oil seepages from the base of Bear Rock, near Nor-man, at almost the very spot where oil was struck nearly one hundred years later. Again, some would-be Klondikers, deterred by the hardships of the route, remained to prospect around Great Slave lake, and were the first to report the Pine Point lead-zinc occurrences there and the gold-bearing veins on Yellowknife bay. Sporadic prospecting followed at the latter locality for over thirty years before the recent rich strikes were made. Similarly, in 1847, Dr. John Rae picked up a boulder of copper ore south of Rankin inlet, on Hudson bay. More than eighty years later, a body of copper-nickel sulphides carrying values in platinum metals was found at this locality. Also, the report of cobalt bloom on the east coast of Great Bear lake brought back by a Geological Survey of Canada party in 1900 was a factor in the events leading to the discovery of silver and radium there in 1930.

Jan 1, 1937

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

By G. W. H. Norman

INTEREST in the mineral possibilities (gold, copper) of northern Quebec, north of the Quebec-Cochrane branch of the Canadian National railway, has centred for many years in the Chibougamau district (see Figure 1). Since 1934, however, promising gold discoveries in the Rose Lake-Florence River section, 115 miles southwest of Chibougamau lake, have widened the interest, and prospectors have examined other parts of the country between Chibougamau lake and Bell river and the surrounding districts. The object of this paper is to !resent an outline of the geology, and to describe the mineral deposits, o part of this region, or, more specifically, of the part embraced by the Opawica-Chibougamau and Waswanipi map-areas(l), which include the districts about Chibougamau lake and Rose lake-Florence river, where mineral deposits are now in course of development either by surface or underground work. Early discoveries, developments, and explorations in the Chibougamau district are well summarized in the report of the Chibougamau Commission, published in 1911(2). The Commission discredited previous optimistic accounts of mineral discoveries in the area, made initially in 1903, but at the same time they expressed the opinion that, from a geological standpoint, the district promised a reward to diligent and intelligent prospecting. Their general conclusion-that prospecting in the area was not then (1911) commercially advisable in view of its inaccessibility and other handicaps shifted interest from the district until, some years later, valuable discoveries were made in the Rouyn area, and aircraft widened the field of successful exploration. During the past ten years or so, considerable energy has been spent in promoting the development of the district. The net result has been the discovery of a number of prospects, the majority of which have been explored only by trenching and, in most cases, diamond drilling.

Jan 1, 1936

By G. W. Birge, D. E. Wolfson, J. G. Walters

Seventeen samples were carbonized by the BM -AGA pilot - plant test method and in industrial ovens . Chemical and physical properties of the samples were determined , and the physical properties of the cokes prepared by the two methods were compared . Since the capacity of the plants from which these samples were obtained is about 30 percent of the 1959 total for the United States , the data given in this report are indicative of the chemical and physical properties of blends used to produce industrial cokes and the acceptable chemical and physical properties of the resultant coke .

Jan 1, 1964

By Hugh P. Godard, K. Winslow

"AbstractA number of panels of various aluminum alloys in different combinations and secured by steel and three types of aluminum rivets were exposed underground at two locations in a Northern Ontario gold mine for two years and then examined to determine the extent of corrosion. The results indicate Alcan 65S-T to possess considerable advantages over Alcan 178-T, which has been employed in the construction of light skips and cages with considerable success for almost twenty years. Information on the behaviour of these alloys when used with steel rivets and in mixed combinations with themselves was obtained.IntroductionBy the complete substitution of aluminum alloys for steel in the fabrication of mining skips and cages, their weight can be reduced as much as 50 per cent. Lesser savings are possible though its savings are possible through its plates, doors, reinforcing members, etc. Reduced weight leads to economy through increased hoisting efficiency.For a new installation, the basis of design is the rate of production, which thus fixes the live load to be hoisted per trip. A lighter skip permits the use of a lighter rope and a smaller hoist. In deep shafts with high-speed hoists operated in balance, the power required for accelerating is considerable. The hoist size is determined by the weight of skip, load, and rope plus the force required to accelerate or decelerate these three elements A light skip may result in a considerably lighter rope. This is important because, even though the skip can be completely balanced this is not true of the rope. Partial balancing is possible, but conical hoist drums or other devices for this purpose are costly; thus a smaller rope results in a smaller hoist, with consequent general reduction in cost of the whole installation. A reduction in power consumption is also obtained as a result of keeping to a minimum the amount of unbalanced load and the weight of all moving parts which must be accelerated."

Jan 1, 1950

BENEDICT SHUBART: I am rather surprised at one statement of Mr. McKeehan, that he found it satisfactory to bond only one track. It has always been my idea of good practice to bond both tracks and cross bond frequently, so that in case of any break in the bonding of one track, which frequently occurs, there will be no interruption in the circuit.

Jan 1, 1923

By Roger T. Laine

"The Carswell structure, located in the western part of the Athabasca Basin, northern Saskatchewan, has been extensively explored since 1967. This exploration has been successful and lead to the discovery, in 1970, of the D sandstone-hosted unconformity related deposit. By the end of 1984, five additional basement-hosted unconformity related deposits had been delineated: the OP and N discovered in 1970, the Claude in 1971, the Dominique-Peter in 1981, and the Dominique-Janine in 1984. The D deposit has been mined out; the Claude open-pit has already produced more than 500 tonnes of uranium, the development of the Dominique-Peter underground mine (first phase) has been completed, and production from the latter started in 1985.All six deposits are located in the southern part of the Aphebian metamorphic core, 18 km in diameter, which has intruded at least 1250 metres of Helikian Athabasca Group sediments during a cryptoexplosion event at 480 Ma, unrelated to the emplacement of uranium mineralization. The metamorphic rocks, affected by the Hudsonian Orogeny, are divided in two lithostratrigraphic units: the Peter River gneiss, aluminous gneiss series, and the Earl River complex, mixed quartzofeldspathic and mafic gneiss series. A well developed regolith profile is recognizable in the south along the contact with the sandstone and inside the metamorphic core sometimes associated with conformable sandstone beds.Basement and sandstone-hosted uranium deposits show many similarities:-linkage to unconformity;-mineralogy and geochronology with a first phase mineralization characterized by a polymetallic sulphide-uraninite-brannerite assemblage dated at 1150 to 1050 Ma, a second phase characterized by a simple sulphide-uraninite assemblage dated at 890 to 820 Ma, and a third phase characterized by a pitchblende-hematite dated at 380 Ma; and,-linkage to early Hudsonian structures with remobilization of these structures during intense hydrothermal alteration resulting in Mg chlorite-illite halos."

Jan 1, 1986

By K. A. Wheeler

To evaluate the effects on groundwater of a proposed in-pit disposal operation at an east Texas lignite mine, the local geologic, hydrogeologic, and geochemical features were thoroughly characterized. Resultant data were used in a flow and transport model (SWIFT) to simulate migration of the ash leachate. Computer simulations indicate that the leachate plume will travel 61-152 meters from the disposal area in 100 years after resaturation of the spoils. A 61-meter buffer zone of mine spoils without ash will surround the disposal area. The proposed landfill operation received regulatory approval and is currently operating as a Class 2 non-hazardous landfill.

Jan 1, 1994

By Martha E. Smith

INTRODUCTION Radiation is one of the many agents occurring in our environment that is capable of causing cancers. We are all unavoidably exposed to natural background radiation. If we wish to exploit the beneficial uses of radiation in medicine, industry, and for the production of electricity, some further exposures to radiation are almost inevitable. One needs to ensure therefore, that the standards of radiation protection are safely derived and one would want to understand the mechanism by which radiation might cause cancer and genetic defects. In order to study the effects of radiation one can: (1) analyze human data, (2) perform animal experiments, and (3) do molecular level experiments. Indeed all three kinds of information are needed. This paper will concentrate on the steps required to obtain some of the necessary human data regarding health effects, where the concern is about the impact and consequences of long-term low-level exposures to an agent. Such investigations require some knowledge of work histories, dose histories, health "outcomes", and the personal identification of the individual involved. Three inter-related computer systems have been developed at Statistics Canada which have been designed to permit optimal use of a number of different records for our entire country for such health related research. The development of the Canadian Mortality Data Base, the initiation of the National Cancer Incidence Reporting System, and the development of new computer linkage techniques have helped reduce the cost and increase the scale and efficiency of automated follow-up to produce statistics of sickness or death associated with radiation and other carcinogenic agents in mines. These computer systems have already been implemented, and references will be made to studies currently being conducted using these files and facilities (e.g. a study of all Ontario miners, plus various Canadian uranium, fluorospar, salt and nickel miners). We will also look at the kinds of data that need to be collected now, to improve such studies in the future. DELAYED RISKS - THE STUDY SIZE AND COST Delayed effects on human health, as for example industrially caused cancer, can in general only be detected and measured by following-up the individuals to see what eventually becomes of them. What is not generally recognized is that the relatively low levels of individual risk, about which the public is often concerned, usually requires for their detection that very large numbers of "exposed" and "control" individuals (e.g. 10,000 to 100,000 or more) be followed over a period of two or three decades to determine when they die, what they die of, and whether they contracted cancer or some other disease of special concern. Thus, it is frequently exceedingly difficult to make such investigations cost-effective so that they will be undertaken at all, and as a result very real risks to health can remain undetected or unquantified. THE MANUAL PROCEDURES Follow-up of individuals by epidemiologists has until recently been a largely manual and clerical operation. It has used a diversity of source record files; local, regional, and national. Often the tracing of people has involved letters sent through the mails and visits to institutions, physicians, municipal offices, and former neighbours. Only thus could one find out whether the individuals were dead or alive. Such studies were necessarily small, or else very expensive. Death registrations have, by tradition, provided a valuable tool for the identification of harmful influences in the environment. However, with the increasing mobility in the population, death may often occur far away from the place of exposure to such an influence. Thus, no longer will simple manual searches in a single registry office suffice to inform the investigator concerning the deaths that may have occurred in a study population, especially when that population is large. In the past, manual follow-up to locate the relevant death registration normally required some prior knowledge of the province and year of death in question, so that the alphabetic indexes could he used to direct researchers to the appropriate bound volumes of registration forms. To search manually in this fashion for any large number of death registrations, without knowing in which year or province the deaths had taken place, or even whether they had yet occurred, would be impractical, since each year in Canada there are about 170,000 deaths. DEATH AND CANCER AS SPECIAL ENDPOINTS Much of recent effort has been focused on the organization of the "endpoint" files required to do long-term follow-up studies on a national scale, because that is a function which other institutions are unable to perform due to the confidentiality laws governing the use of such information. Outside organizations generally come to us with detailed "starting" point records which relate to some specific group requiring study. We carry out these epidemiological searches on a cost-recovery basis. The analytical interpretation of results is normally

Jan 1, 1981

By Gerardo H. Achurra

During the last years, the Caletones Smelter, like others copper smelters in the world, has evolved from the conventional, inefficient, pollutant and expensive technologies, to modern, environmentally friendly and efficient ones. For this reason' as well as to improve its competitive position this Smelter shut down the reverberatory furnace, started up two big acid plants and has developed some pyrometallurgical technologies. The main facilities of the Caletones Smelting and Converting Process, in the present and the future, are the Teniente Converters, the reactors with a high operational availability that have reached concentrate top process capacities near to 2,400 tpd. These reactors operate in most of Chilean smelters as well as in other smelters in the world such as in Zambia, Peru and Mexico. Since 2000, the Caletones Smelting and Converting Process, has been adapted in two Teniente Converters, four Slag Cleaning Furnaces and four Pierce -Smith Converters. These facilities, together with the operation of two Fluidized Bed Dryers and two Oxygen Plants have allowed to reach concentrate smelting capacities and copper productions of 1,250 ktpy and 380 kfipy, respectively. Associated to EI Teniente Division Expansion Plan, Caletones Smelter, in the first stage, will increase its capacity to 1,440 ktpy in 2004. In the long term, Caletones has different options, such as the processing of 1,600 to 2,000 ktpy of concentrate, producing anodes, white metal or a mixture of them. These options are connected with CODELCO's Smelters & Refineries Strategic Plan, including Mejillones Project. The main challenges of Caletones Smelter are associated to the development and the consolidation of the Continuous and Environmental Friendly Processes, automation and control of different processes and to the improvement of its leadership between other Copper Smelters in the world.

Jan 1, 2003