Search Documents

On Dec. 20, 2013, an 8-m (26.2-ft) diameter Robbins hybrid single shield/earth pressure balance tunnel boring machine (EPB TBM) was launched to bore the Grosvenor decline tunnel for Australia?s Anglo American coal mine. The machine was built using onsite first time assembly (OFTA) in order to fit within a tight project schedule. Assembly at the remote jobsite near Moranbah, Australia took about four-and-a-half months, and then the machine was walked down into a launch tunnel. Two decline tunnels, at grades of 1:6 and 1:8, will be used for mine access to new coal seams. The hybrid machine is tackling mixed ground conditions ranging from sand and clay to varying types of sedimentary hard rock up to 120 MPa UCS, as well as coal seams. Methane gas is expected to be present throughout the tunnel, so the machine has been designed as explosion-proof-compliant to ERZ-1. ?Grosvenor is the first underground coal mine in Queensland to use a TBM for drift construction,? said Glenn Tonkin, Grosvenor project director. ?We are proud to be pioneering this technology.? Only about 300 m (984 ft) of ground in each decline tunnel is expected to require EPB mode, while the rest of the tunnel will be bored in hard rock mode. Thus, the design was optimized toward hard rock excavation.

By J Caron, M Athayde, F Lavoie, R Joyce

Decarbonisation has become a major challenge for the global steelmaking industry, turning towards new technologies aimed at carbon footprint reduction, which on its own accounts for approximately 9 per cent global emissions. The iron and steel industry represents a ‘hard to abate’ sector, where much of efforts are currently being deployed into initiatives aiming to decarbonise the ironmaking through the use of green hydrogen, carbon capture utilisation and storage and state-of-the-art operation of current technologies, while little efforts being deployed to find carbon-efficient solution to iron ore burden preparation, where high-grade iron concentrate will increase in importance to ironmaking regardless of the chosen reduction route. Quebec Iron Ore (QIO), a subsidiary of Champion Iron Limited (Champion), produces high-grade hematite concentrate with one of the lowest carbon global footprints. Still, QIO is partnering with its clients to the development of burden solutions to minimise CO2 emission, in the seek for a decarbonised steel. In a strong technological partnership, Binding Solutions Limited (BSL) has developed a novel, coldbinding technology to provide a cleaner, more cost-effective alternative to induration. The technology allows miners and steel producers to reduce Capex significantly and reduce energy consumption and CO2 emissions by 90 per cent. QIO and BSL have partnered to adapt the disruptive cold binding technology developed by BSL to QIO’s concentrate to produce a high-quality low emissions iron ore agglomerate. This paper describes the efforts taken to further develop BSL’s cold binding technology and its application to QIO’s high-grade iron ore concentrate to produce a hematite cold bonded briquette (hCBB) showing comparable performances with high quality seaborne fired pellets.

Nov 8, 2021

By Kelsall D. F, Trahar W. J

The size by size batch flotation behaviour of copper activated sphalerite from synthetic mixtures with quartz was determined. In terms of recovery of sphalerite, the size fractions could be grouped into coarse, intermediate, and fine ranges. The behaviour of the coarse and fine ranges was significantly poorer than that of the intermediate range in both the extent and rate of flotation.Each size fraction had a fast and a slow floating component.The main effect of changing the copper sulphate addition was to alter the proportion of any size fraction which was fast floating. No correlation could be found, between the amount of copper on the spha:lerite andeither the flotation rate of the mineral or the amount of copper added to the system. It was found that fine particles did not appear to consume greatly disproportionate amounts of copper sulphate during conditioning. A modified conditioning procedure was found to lead to a higher rate of flotation and recovery of coarse sphalerite and to make poss1ble substantial savings of copper sulphate.

Jan 1, 1975

By John R. Craynon

Science and Sustainable Development Each of the ?pillars? of sustainable development are directly impacted by mining. We need science to understand exactly how mining contributes to each. Overview of presentation ? History of mining and sustainable development ? Role of stakeholders in measuring/accepting contributions of mining to SD ? Identified ?shortfalls? in understanding mining and SD ? Science needs

Aug 1, 2013

By E. F. Schnitzer, D. R. Haight, G. T. Krogman

The 1997 New Year’s Day Rogue River flood near Medford, Oregon, USA, entered historic channels, eroded a 150-foot-wide buffer, and captured an inactive gravel pond located within the channel migration zone. Channel redirection caused by pit captures threatened adjacent inactive gravel ponds. In response to this capture, a stakeholders group of concerned individuals and organizations was formed. This group ultimately developed a rehabilitation plan, which conformed to the Rogue River’s geomorphic trends. A two-dimensional model, FLO-2D, was used to evaluate channel splits, flood storage, backwater, and future conditions. Modeling results coupled with trend analysis were used to create a stable design where stream barbs, gravel redistribution, a channel outfall spillway, bendway weirs, bank reshaping, and revegetation were integrated into a single plan for a three-mile reach. The quick action by the stakeholders group averted further damage to the Rogue River system and surrounding environment. The project has preserved three miles of mainstem habitat, one mile of side channel habitat, and protected ten gravel ponds from pit capture.

Jan 1, 2006

By R. S. Dean

"Interest in the nitrogen content of steel has increased sharply in the last few years. Investigations have indicated that its presence in steel has an important bearing on high temperature brittleness3, magnetic properties4, room temperature hardening5, and shock resistance. The steel producer may therefore look forward with certaintly to the necessity of controlling this element in a considerable proportion of his product. The literature, however, reveals a great many contradictory statements concerning the percentage of nitrogen which must be present to produce given effects on the properties of iron and steel. Most of these arise from a misunderstanding of the nature of the iron-nitrogen diagram near the iron end and a lack of recognition of the effect of state of aggregation on physical properties although both have been fairly well worked out.My thanks are due to Mr. J. L. Gregg, Prof. R. H. Dowdell, Mr, R. F. Mehl and Mr. H. C. Vacher for suggestions in connection with the preparation of this paper, and to Mr. C. H. Hefty and Mr. G. T. Motok for furnishing a valuable bibliography and translations of articles by Must and Duhr.The iron-nitrogen diagram in the solid state, so far as it concerns the nitrogen content of commercial iron and steel, consists simply in a solubility curve increasing with temperature. The important thing about this solubility curve is that without cold wore the iron nitride when precipitated does not go into solution on heating for long periods below 300°C. This slowness of solution is probably due to the fact that iron nitride when present as a separate phase has at these temperatures an equilibrium pressure of several thousand atmospheres7 and that therefore each particle of iron nitride surrounds itself with a layer of nitrogen. The precipitation of such an unstable crystal presents points of interest thermodynamically but we can not go into these here. It is quite well established that it precipitate. It can not diffuse then unless this layer is broken through or the temperature and pressure are increased to a point where the nitrogen is absorbed at an appreciable rate in the surrounding iron. This rate will depend on the degree of unsaturation of the iron and the excess pressure of the nitrogen above equilibrium pressure. The degree of unsaturation is determined by the temperature alone so that the temperature at which the rate of solution of the nitride becomes appreciable will depend on the pressure of nitrogen developed. This, in turn, will depend on the balance between rate of decomposition of the nitride and the rate o: flow of the iron. In annealed iron, this temperature of appreciable solution rate is between 300 and 350°C.8 By cold work, however, the elastic limit of the iron is increased, and conditions for the nitride to go into solution are reached at a much lower temperature, giving rise to the so-called blue brittleness. This brittleness and hardening is due to iron nitride going into solid solution and is not precipitation hardening."

Mar 1, 1931

The major factors limiting the establishing of vegetation on the shale and sandstone wastes at Minto are high exchange acidity and low pH (shale pH 4-5, sandstone pH < 4). In the first revegetation program (1967-74), 3.8 million trees were planted without grading on 4,000 acres (red, jack and scots pine and black locust). White dutch and sweet clover, birds-foot trefoil and red top were established in selected areas, and ponds were stocked with brook trout. In the second phase of reclamation, beginning in 1979, a comprehensive plan will be initiated which will allow for forest production, wildlife development and recreational activities.

Jan 1, 1977

By Luis Orna

En el 2017, con un capital de prototipo de $35 000, un retorno de inversión de 7 meses y una contribución adicional de reservas Au en 2018 de 3 612 331 onzas (37% adicional del estimado en exploración de Yanacocha en un año), se implementó una solución robótica para la evaluación óptima de reserva de minerales, gracias a la que se logró incrementar la ley promedio de 0.35% a 0.93% Au, así como la precisión de bloques en depósito de mineral, de 69% a 89%, sin sustituir la mano de obra (como ingenieros geólogos), sino brindándoles una herramienta precisa adicional. Asimismo, al utilizar al robot en la exploración y prospección de minerales, se logró reducir campañas de exploración de 4 años a 1.5 años, así como los costos, de $5M a $2M por campaña de exploración. Finalmente, el robot también se implementó en el ambiente de seguridad ocupacional, de manera que se logró mantener en cero los accidentes por derrumbes.

Sep 20, 2019

By J. E. Dutrizac, J. B. O'Reilly

"Zinc is a relatively abundant element which occurs as both high-grade sulphide ores {sphalerite ZnS) and oxide ores which the ancients collectively termed ""calamine"" (smithsonite ZnC03 and/ or hemimorphite Zn4Si201(0H)2 - H20 and/ or hydrozincite Zn5(C03) 2(0H)6). Although oxidic zinc is readily reduced by carbon, the process becomes thermodynamically viable only at - 1000°C, and at this temperature the zinc is released as a vapour (B.P. 907°C). Casual cooling of the vapour results in its re-oxidation by excess combustion air or even the carbon monoxide product of the reduction reaction. ZnO + C = C09,, + Zn vapom Only fairly rapid quenching of the zinc vapour and the isolation of the reduction products from the combustion gases will yield metallic zinc; these conditions were not produced deliberately until the advent of distillation technology. Until quite recently, the principal use of zinc was in brass manufacture; galvanized iron was not discovered until the 19th century and zinc casting alloys are a relatively recent invention. As will be seen, brass could be produced without recourse to a pure zinc intermediary, and the discovery of brass preceded that of zinc by many centuries. The purpose of this paper is to outline the discovery and early development of both zinc and brass with special reference to the European scene."

Jan 1, 1999

By Stefan Basista, Janusz Tomala

Modern constructions of electric ferroalloy furnaces are still based on applying in the lower "liquid" areas the standard carbon materials. What can be illustrated by the experience from several years, in the part of tap hole, hearth walls and bottom, is that so-called carbon or semigraphite microporous materials are successfully being applied. These materials, compared to the standard carbon, give better resistance to the attack by liquid metal and other wear factors. Generally this group includes materials characterised by considerable share of pores of diameters below1µm (significantly exceeding 90% of total porosity). The microporosity increases the resistance to the infiltration of the liquid metal. The effect of microporosity can be obtained by introducing silicon (or its compound) additive to materials based on electrically (or gas) calcined anthracites, electrographite and binder. Moreover, by introducing other ceramic additives, the microporous materials are more resistant to dissolution by the liquid metal. Observing the trends of "improving the materials" in the last years, it is clearly seen that the share of non-carbon additives is bigger and bigger, so we can reasonably speak of rather carbon-ceramic materials. In this paper, the survey of the most important quality criteria, which must be met by the carbon furnace linings, as well as the new testing methods will be presented.

Jan 1, 2007

By Lijun Xu, Jan M. Mutmansky

"Mutmansky, J.M. and· Lijun Xu, 1989. Some observations on particulates collected in underground coal mines using diesel and non-diesel equipment. Min. Sci. Technol., 9: 207-218.The results obtained when sampling twenty underground coal mine sections, each in a different mine, are outlined. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a fairly detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons of the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines lising diesels only for outby utility haulage. Particulates in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be drawn from the limited data, a more detailed study of particulates may provide a better picture of particulate loadings.IntroductionThe subject of particulate emiss1ons from underground diesel equipment is currently a very important topic as health concerns and regulation of diesel particulate emissions have created new environmental problems for mine operators. The amount of particulate matter originating from diesels has not been extensively measured and problems of differentiating coal and mineral dust from diesel particulates make existing data questionable.However, it is necessary to make an assessment of the problem in order to solve it. It is known that particulates from diesel engines are solid aerosols formed in the combustion process. Technically, this places the particles in the category of fumes. It is also known from tests where no mineral dust could be a factor in the measurements that about 90% of diesel particles are less than 1 µm in aerodynamic diameter [3]. To measure the diesel component of a coal/diesel particulate to measure, Johnson et al. [2] have developed procedures for utilizing laser Raman spectroscopy. The determination of diesel content in a coal/diesel mixture is difficult due to the chemical similarity of the two organic materials. However, laser Raman spectroscopy, which is often used for identification of organic materials, has potential if the Raman spectra for the two materials are different and unique. The study concluded that an accuracy of ±~% could be achieved for mixtures containing up to 55% diesel particulate. The method is relatively complex and would need further development for routine application."

Jan 1, 1990

Plant for the production of sulphuric acid from pyrites flotation concentrates was commissioned at Cockle Creek during 1956, to meet increasing demands for commercial acid and superphosphate. Pyrite was chosen as raw material because of the uncertain supplyposition of imported brimstone and the desirability of utilising domestic sulphur.Desulphurisation of the pyrite is performed by two 40-ton per day roasters of the Turbulent Layer type operated under licence from the Badische Analin and Soda Fabrik (B.A.S.F.) organisation. These units are the first of their kind commissioned in the southernhemisphere. Pyrite is fed to the roasters in the as-received un-dried condition. Waste heat steam production is coupled with electricity generation within the plant. Sulphur dioxide is produced at comparatively high strengths and cleaned by conventional cyclone and hot electro-filter equipment.The acid unit has a capacity of 100 mono tons of sulphuric acid per day and includes cooling and wash towers, mist precipitators, a single stage drying tower, 4-pass oxidation section and absorption system.INTRODUCTIONSulphuric acid has been manufactured at Cockle Creek Works since 1913, when the first chamber nitration plant was commissioned. The raw material was brimstone roasted in Herreschoff furnaces. Since that time three additional chamber units have been constructed and have produced acid from brimstone, zinc concentrates, pyrites and -spent oxide, according to changing economic and supply factors.Three chamber units are still in operation. Contact processes have become increasingly important since the first Schroder-Grillo unit was commissioned in 1923. Six of these 5-ton per day units were operating in the mid-thirties, but have since been demolished. Two 15 ton Chemico hot gas contact units commenced operation in 1937 and 1938, and although modified, are still in service.The increasing demand over recent years for sulphuric...

Jan 1, 1957

By Lumley G, Rowlands D

The overburden slusher (OS) is proposed as a stripping tool that is expected to find application in overburden stripping operations including open cut coal and oil shale mines. OS is expected to combat the effects of increasing depth on the productivity of conventional dragline stripping.Although previously developed stripping techniques have included the use of drag scrapers the OS is sufficiently different as to constitute a new stripping method.A study undertaken at the University of Queensland during 1985 is believed to be the first major study on the use of the OS and preliminary economic results are very encouraging. It appears that the OS has the capacity to remove overburden at a cheaper unit cost than the equivalent powered dragline stripping machine at any comparable depth of overburden. The OS is not adversely affected by increasing stripping depth to the same extent as a dragline. In addition, the action of the OS machine allows for the lowering of spoil face angles, thereby reducing spoil slope stability problems encountered in deep open cut strip mines.

Jan 1, 1986

By H. B. Hill

Virtually from the date of its discovery in December 1928 the Oklahoma City oil and gas field, Oklahoma County, Okla., has attracted national and international attention. The history of the field has been associated closely with rules and regulations pertaining to production control and proration practices. Early development was rapid, and Oklahoma City soon attained the distinction of being the first major field in which the producing wells were over a mile in depth. Before the structural features of the reservoir had been disclosed every outpost well was considered a "wildcat", so complex appeared the underground geology, The wells not only were deep and the reservoir pressures high, but the production from the early wells was a high A.P.I. gravity oil, accompanied by large volumes of gas. Several "blow-outs" and fired occurred during the early development, and the close proximity of these now unusual events to a large city gave the field much publicity, both local and national. Later, when its production threatened to demoralize the market for oil and its products, the Oklahoma City field again attracted wide publicity. The then little understood geology of the underground reservoir and the diversity of ownership of the land overlying the producing structure made orderly development and production difficult to enforce. Proration was enforced with difficulty., and the, rate of production from the field continued to increase until, on August 4, 1931, martial law was declared in all prorated fields of the State, and most of the wells in the Oklahoma City field wore shut n. On October 9, 1931, permission was granted t o reopen and prod e the wells in the Oklahoma City field. The order permitting production of the wells provided that during the period beginning October 10 and extending to October 20, 1931, all wells in the field that hid not produced more oil than specified under the earlier proration orders and that had been shut in for the required 55-day period were permitted to produce 5 percent of their last potential during that 10-day period. On November 7, 1931, the Corporation Commission of Oklahoma issued an order which divided the Oklahoma City field into the Wilcox, Arbuckle, and Lower Simpson zones for proration purposes. Wells producing from the Wilcox zone were allowed to produce 4 1/2 percent of their potential5/ from November 1, 1931, to January 1, 1932; Arbuckle limestone wells were allowed to produce 250 barrels of oil daily; and Simpson sandstone wells which had a potential of over 2,000 barrels per day or which made 3 percent or more water were allowed to produce 200 barrels of oil per day.

Jan 1, 1937

By Gerald M. Bandholz

Exxon Minerals Company, a division of Exxon Corporation, has been exploring for base metal deposits in the Precambrian volcanic rocks in northern Wisconsin since 1970. Aerial electromagnetic surveys of the area, conducted in 1974, reported an anomaly, near Crandon, in Forest County. In the summer of 1975, the first diamond drill entered the anomaly, representing the 25th prospect Exxon had drilled in Wisconsin. This first hole revealed significant mineralization containing zinc and copper. Subsequent drilling confirmed the discovery of a sizeable zinc-copper massive sulfide are body. 1.1.2 Location The deposit is located in northeastern Wisconsin within a topographical high called the Northern Highlands region. The deposit lies about 5 miles directly south of Crandon and about 2 miles east of State Highway 55 on Sand Lake Road (see fig. 1). Other local communities include Rhinelander 28 miles west, Antigo 45 miles south, and Iron River and Iron Mountain, in Michigan, 75 and 44 miles east and north of Crandon respectively. In relation to the lakes and streams, the deposit lies 0.25 miles north of Little Sand Lake, and about 1 mile south of Swamp Creek.

Jan 1, 1981

By Donald M. Liddell

ALTHOUGH the midday lunches of business associations have been re-echoing the phrases that re- search would lead us out of the depression and that the last place to economize is on research, nevertheless most executives apparently concluded that it was their neighbor who ought not to economize in research, and that in their own plants what had been discovered in 1929-30 was sufficient to lead them out of the wilderness. At any rate, I have discovered much less that seems worth noting, and compared with 1931, the report volume of the committee members is off about 40 per cent, and compared with 1929, about 80 per cent. Evidently there is some hookup with the +tee1 industry as to output, and the Report Reading Committee should investigate this and the relative use of commas and periods.

Jan 1, 1933

By Bowen Li

Silicon Carbide is an excellent refractory material. Its physical properties make it extremely useful, particularly in applications where corrosion resistance and wear are important considerations. Commercial silicon carbide refractory is frequently manufactured by bonding silicon carbide particles with clay; however, clay may cause problems in the sintered products. This study investigates the potential of replacing a portion of the clay with andalusite powder. The results show that micron size andalusite powder can improve not only the strength of the refractory but also the sinterability. The mechanisms for these improvements are discussed.

Jan 1, 2006

By Charles L. Parsons

Early in 1912, from information received by the Bureau of Mines, it became evident that quantities of valuable radium-bearing ore from Colorado were being exported for manufacture in foreign countries and that at least part of the manufactured product was being returned to this country and sold at a price entirely incommensurate with that received by the miner and the prospector. Consequently, in line with its efforts to increase efficiency in the mining and treatment of mineral resources, the Bureau of Mines undertook an investigation of conditions. Results of this preliminary investigation were published, in the summer of 1913, as Bulletin 70,a which gave an outline of the radium deposits of the West, the conditions of mining, the wastes involved, and the status of the production of radium from its ores. At about this time newspapers and medical journals were publishing statements regarding the value of radium in cancer therapy. These reports, although many of them were exaggerated, brought out clearly the remarkable virtue of the gamma rays for the treatment of cancer and other malignant growths. In view of the fact that the largest known supplies of radium ore in the world are in the States of Colorado and Utah and on the public lands of the United States, it was deemed highly important for the Bureau of Mines to study the production of radium in detail. Such study, it was hoped, would enable the prospector and miner to obtain a fairer price for the ores and would furnish information necessary in case Congress appropriated funds to develop methods for extracting radium from ore on the public lands under Government supervision, to be supplied at cost to the hospitals of the Army, Navy, and Public Health Service.

Jan 1, 1915

By Gift Makusha, Dave Minney

Anglo Coal South Africa mines coal for both the domestic and export market using open cast and strip mining methods. To establish a mine, a process is set in place to gather ever increasing amounts of geological and metallurgical data to confirm a proven reserve. Increasingly, geotechnical data are also included in this process to confirm that reserve is easily and safely mineable. The mine design process is an iterative one using a combination of numerical modelling and empirical data to arrive at a mining layout that is both, practical, productive and safe. In South Africa it is a legal requirement to compile a code of practice to combat rock fall and slope instability accidents and these have to be revised annually, reinforcing the iterative process of continual improvement. To ensure best practise occurs, all Anglo Coal operations are subjected to annual 2nd party audits and ad hoc 3rd party audit by independent consultants. This paper attempts to explain the process described above in a concise, but understandable manner. 1.0 GEOLOGICAL SETTING The Ecca sediments date from the Permian period and the coal deposits were formed in glaciated valleys on a basement of Dolomite, Ryolite or Granophyre rock types. The sediments overlying the coal deposits are typically flat lying and multiple bedded. The sediments consist of mudstones, shales and sandstones and are generally capable of forming stable highwalls given the time that they must stand up for. Anglo Coal extracts coal from the Witbank, Highveld and Vereeniging coalfields. The Witbank coalfields contain five seams numbered from the base upwards, 1 to 5 Seam; Highveld coalfield the 2 and 4 Seam and the Vereening area the seams are described as Top, Middle and Bottom seams. Coal deposited over the basement Dolomite formation display very erratic dips, as contemporaneous subsidence occurred in some instances over sinkholes that were forming, resulting in local thickening of the coal deposit and resulting in strata that dips toward the centre of the sinkhole.

Jan 1, 2006

A symposium on pneumatic transportation of solids was held at Morgantown, W. Va., October 19-20, 196&apos;), under the cosponsorship of the Institute ref Gas Technology. Chicago, Ill., and the Bureau of Mines. Objective of the symposium was to present information on developments and projected programs in the technology of feeding, transporting, recompressing, and utilizing gas-solids mixtures Dr. Henry R. Linden, Director, Institute of Gas Technology and Harry Perry, Director of Coal Research, Bureau of Mines, in the initial addresses at the symposium welcomed more than 140 representatives of industry, educational institutions, and government from 16 states, Canada, Great Britain, etc.

Jan 1, 1966