Search Documents

By Frank Cook

As in other areas of the country, surface coal mine productivity in the Central Coal Province--primarily Illinois, Indiana, and west Kentucky--has declined steadily since 1969 (figure 1). Productivity, as measured in tons of clean coal produced per man-shift, dropped 35 percent during the period 1969-1975. Unwelcome at any time, this phenomenon is particularly untimely now, when increased coal production is a national goal. The U.S. Bureau of Mines has been working with the coal industry to develop new operating methods and equipment to enable increased productivity and improved reclamation performance in surface coal mining. Several projects have involved identification and evaluation of existing overburden handling and reclamation practices, and development of means to improve operational procedures. Some results of one of those projects, as they apply to the Central Coal Province, are summarized in this paper.

Jan 1, 1977

By Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie

In the present study, the oxidation process of vanadium and chromium bearing hot metal was investigated by using CaO-FetO-SiO2 slags at 1653K in MoSi2 furnace. The results indicated that both the vanadium distribution LV and chromium distribution LCr were of the orders of 2.2~2.4 with the basicity range of 1.32~1.78 and FeO weight percent range of 28%~45%. Both LV and LCr decreased with increasing basicity and decreasing FeO weight percent. The phosphorus distribution LP was of the order of 1.34~1.56. However, LP increased with increasing basicity and decreasing FeO weight percent. The oxidation ratio values of V and Cr in hot metal were above 84% and the values of P were nearly 50%. In other words, it means the addition of CaO in vanadium slag provided a certain ability of dephosphorization along with keeping high oxidation ratios of V and Cr.

Jan 1, 2015

By Rustu S. Kalyoncu

A major goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. In support of this mission, a survey of the state of the art of chemically bonded refractories has been made, covering the scientific literature, government reports, and patents. This review includes research and development results for phosphate, silicate, oxychloride, oxysulfate, and other bonding agents used in refractories manufacture. A significant finding of the review was that references on bonding mechanisms, bond formation kinetics, and other important process parameters and conditions were few and universally vague. As a result, recommendations are made to expand research efforts to investigate the kinetics and mechanisms of reactions in chemically bonded refractories.

Jan 1, 1982

By Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Jian-jun Hu

It could significantly increase the leaching rate of refractory gold concentrate containing sulfur and arsenic by roasting pretreatment with adding certain amount of sodium sulfate, and the mechanism of that was systematically researched with DSC, XRD and SEM in this paper. Results indicated that the mechanism of Na2SO4 on double refractory gold concentrate at roasting pretreatment can be summed up in the following three aspects：Firstly, Na2SO4 can react with SO2 and SO3 which is produced by the oxidation of sulfides and generate Na2S2O7(l), which plays buffer effect on sulfides exothermic oxidation, avoiding the secondary-encapsulated of gold. Secondly, the liquid phase of Na2S2O7 can cover mineral particles' surface that possesses a sintering effect, it leads to internal cracks of the particles. Finally, mineral particles will gather with sodium sulfate particles as the center that can improve the permeability of the layer.

Jan 1, 2015

By Rob G. Jeffrey, Ken W. Mills, Jesse W. Puller

"A coal mine in New South Wales is longwall mining 300m wide panels at a depth of 160-180m directly below a 16-20 m thick conglomerate strata. As part of a strategy to use hydraulic fracturing to manage potential windblast and periodic caving hazards associated with this conglomerate strata, the in situ stresses in the conglomerate were measured using ANZI strain cells and the overcoring method of stress relief. Changes in stress associated with abutment loading and placement of hydraulic fractures were also measured using ANZI strain cells installed from the surface and from underground. This paper presents the results of in situ stress measurements and stress change monitoring undertaken as part of the hydraulic fracturing program.Overcore stress measurements have indicated the vertical stress is the lowest principal stress so that hydraulic fractures placed ahead of mining form horizontally and so provide effective pre-conditioning to promote caving of the conglomerate strata. Monitoring of the full-scale hydraulic fractures has confirmed the hydraulic fractures grow horizontally.Stress changes monitored during hydraulic fracturing formed part of a broader program to investigate fracture geometry and growth rates to confirm the characteristics of the hydraulic fractures placed. This monitoring showed that vertical stress in the conglomerate strata was being increased by up to 1 MPa in close proximity to the hydraulic fracture and had the effect of tending to promote asymmetrical growth of subsequent fractures about the injection borehole.Monitoring of stress changes in the overburden strata during longwall retreat was undertaken at two different locations at the mine. The monitoring indicated stress changes were evident 150 m ahead of the longwall face and abutment loading reached a maximum increase of about 7.5 MPa. The stresses ahead of mining change gradually with distance to the approaching longwall and in a direction consistent with the horizontal in situ stresses. There was no evidence in the stress change monitoring results to indicate significant cyclical forward abutment loading ahead of the face consistent with the observations of face conditions underground adjacent to both measurement locations. The forward abutment load determined from the stress change monitoring is consistent with the weight of overburden strata overhanging the goaf indicated by subsidence monitoring."

Jan 1, 2015

By Bruna de Camargo Lemos

O objetivo deste trabalho compreende a realização da síntese de SnO2 dopado com aditivo Sr2 contendo diferentes quantidades molares de SrO (X)SnO2+(1-X)SrO, em que o cátion Sr2+ foi introduzido através do nitrato de estrôncio variando de 5 à 50 % em mol para uma mistura tanto em meio aquoso quanto em meio alcoólico, seguida da calcinação do pó resultante que é feita à 700°C com uma taxa de 10°C/min. Análises de caracterização como difração de raios X, área específica, calorimetria exploratória, picnometria a gás e determinação do ponto isoelétrico das suspensões aquosas foram realizadas de modo a verificar qual o agente dispersante mais apropriado para as características ácido-básicos da suspensão em questão. A partir deste determinar o potencial zeta do composto estudado através da eletroforese. Compostos intermediários a base de estanato de estanho foram identificados, e a deposição por eletroforese foi realizada com sucesso, uma vez que foi possível obter uma suspensão estável a partir dos pós cerâmicos produzidos.

Aug 16, 2017

By PHILIP A. ZANG

The rapidly increasing use of motor vehicles in the United States has introduced an entirely new problem in the proper ventilation oftunnels , subways , and other confined spaces through which such machines must pass . This problem was brought to the attention of the Bureau of Mines by the New York and New Jersey State Bridge and Tunnel Commissions with reference to the ventilation of the proposed vehicular tunnel under the Hudson River . This tunnel , consisting of twin tubes 29 feet in diameter and 8500 feet long between entrance and exit , presented an unprecedented problem in ventilation both on account of its length and on account of the traffic density , which is expected to reach a maximum of 1900 vehicles per hour . An exhaustive study by the tunnel engineers of all available data on the amount and composition of automobile exhaust gas disclosed very little information on the percentage of carbon monoxide in motor exhaust gas from the average run of automobiles and trucks under actual operating conditions on the road. It was well known that carburetor adjustment and other operating factors changed the percentage of the poisonous constituent , carbon monoxide , from practically 0 to 12 or 13 per cent ; but no safe estimate could be made of the most probable figure without further investigation .

Mar 1, 1921

By Sandeep K. Sharma

The U.S. Bureau of Mines has been investigating new techniques to improve the of mineral to recover water lost in the waste slurry, and to produce dewatered solid dewatering s suitable for disposal. As part of this investigation, a study was undertaken to investigate the feasibility of dewatering Alaska placer effluent. Based on the laboratory tests, preliminary field tests were conducted on three placer mines in Alaska. At these mines, the water recovered from the placer effluent (250 to 23,000 NTU) exhibited turbidities of 20 to 240 NTU. In the second year of the project, a large-scale dewatering unit was set up at a mine located in the Livengood district. The feed, at flow rates up to 935 gpm, was mixed with dilute PEO solution in a flexible plastic hose with and without static mixers. Feed to the dewatering unit generally ranged between 300 and 26,500 NTU and required PEO dosages of 0.02 to 0.14 lb per 1,000 gal to produce water from the screen underflow with turbidities of 20 to 50 NTU. During this period, a small unit was also operated at Dow rams of 10 to 25 gpm at sewn sites throughout Alaska, with the effluent from four of the sites being dewatered successfully.

Jan 1, 2010

By Michael Murphy, Khaled M. Mohamed, Berk Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in underground coal mines to reduce rib fall accidents and fatalities. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified.This paper presents a coal rib model to simulate the mechanism of coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff Mine in Australia. Fracturing of the coal rib was defined by critical VALUES (of plastic shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data.INTRODUCTIONCoal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face failure and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities (MSHA, 2015)."

Jan 1, 2016

By A. C. Mulholland

The electrical control of three-electrode submerged-arc furnaces suffers from a number of complexities, mostly due to the nature of the furnace electrical circuit providing power to the furnace where the three electrodes are interconnected within the furnace through the molten metal bath. This gives rise to what is known as the interaction effect 2, where variations in one electrode?s current can cause comparable changes to the currents in the other electrodes, particularly in larger furnaces with low power factor. Resistance-based control of the electrode penetration has largely alleviated these problems, since the resistance encountered by each electrode is predominantly dictated by the length and conductivity of the current path from the electrode?s tip to the molten metal bath, which acts as the three-phase circuit?s floating neutral point. Hence resistance changes due to tip position or conductivity changes beneath one electrode do not affect the resistances beneath the others, effectively decoupling the control of the individual electrodes1. Although resistance-based control is therefore generally accepted as superior to current-based control for the regulation of submerged-arc furnace electrode penetration, a few furnace operators still prefer to use current control under specific furnace conditions. This paper presents the results of analysing the performance of both current and resistance-based control in typical scenarios encountered on industrial furnaces, taking into account a number of factors including electrode penetration, power distribution, efficiency and asymmetry of the electrode currents. In order to accomplish this, three typically encountered scenarios were simulated. The results obtained show that resistance control provides more benefit in all cases, however, the uneven electrode current distribution generated by resistance control when electrodes are on top stops may cause some concern if baking of the electrodes is required in this scenario.

Jan 1, 2009

By J. Richter, D. Schulze

J. Richter and D. Schulze (Deutschen Akademie der Wissenschafte zu Berlin)—Introduction. In a recent paper R. G. Garlick and H. B. Probst reported on experimental results of investigations of room-temperature slip in zone-melted tungsten single crystals.17 In the paper it was pointed out that slip lines could be detected with an optical microscope only after about 10 pet plastic strain of the crystal. In our investigations we could observe slip lines in tungsten single crystals of defined orientations already with an elongation of 0.02 to 0.03 pet.18"9 Experimental Technique and Results. The tungsten single crystals were produced from 4 to 5 mm sintered rods* as starting material by electron- beam zone melting. With single-zone-pass melting a speed of 0.5 mm per min was used, while three-pass melting could be handled at a speed of 3 mm per min. Crystal axis orientations were located in the shaded area of the stereographic triangle, see Fig. 6. Orientation 1 is located at about 18 deg and orientation 2 at about 5 deg on the great circle from [011] to [ill]. This corresponds approximately to the orientations P and M referred to by Garlick and Probst. Our single crystals had a length of about 70 mm and were profiled solely by electrolytic means, leaving grip ends at both ends of the crystals. Between the latter, a cylindrical crystal of 45 to 50 mm length and about 2.4 mm diam was obtained. The crystals were deformed at room temperature in a commercial tensile-testing machine to obtain a strain of 0.02 to 5 pet. The average strain rate e = eP/t for all tensile tests amounted to approximately 10 -6 to 10-5 per sec, with ep representing plastic strain and t the duration of applied stress. In Fig. 7 a crystal is shown elongated by 0.03 pet. The picture was obtained by means of an optical microscope. Figs. 8 and 9 give electron-microscopic pictures of slip lines of crystals elongated by 0.07 and 1.1 pet, respectively. For crystals with the orientation 1, see Fig. 6, only the two main slip systems (101)[111] and (110)[111] were found. With the crystals of group 2 the two main slip systems are again evident, with

Jan 1, 1965

By R. Anthony Hodge

1. Today?s Reality: Voisey?s Bay EIA Activities of the Canadian Environmental Assessment Agency The Tulsequah Chief Decisions The Bank of Montreal The World Bank World Business Council on Sustainable Development The Government of Canada Many company policies

May 1, 2002

By S. Tuttle, R. Sisson

"Suncor Energy Inc. has proposed a 2.2 billion dollar expansion to the current oil sands operation, which will more than double the productive capability of the facility. As part of the application for this expansion, a comprehensive closure plan had to be developed and filed.Closure planning includes a systematic evaluation of the area to be developed, the development activities planned, the goals and objectives of the corporation in re-establishing landforms and ecosystems at the same time as running an effective operation. As early as is practical during the mine development, surface contouring is completed, soil is reconstructed, and vegetation, surface drainage and wetlands are re-established. Once active reclamation is complete and vegetation has been re-established, Suncor monitors maturation of landscapes and ecosystems to provide the submission basis for reclamation certification"

Jan 1, 1999

By L Salvestro

Ventilation on demand (VOD) has been demonstrated to significantly reduce operating costs for ventilation fans, by reducing fan output to meet demand. The most effective method for reducing operating costs is to use variable speed drives to adjust the speed of ventilation fans as required – this achieves significantly larger power savings that damper or vane control alone.However, this mode of control will significantly increase the number of speed cycles the ventilation fans will experience. Fabricated impellers have a limited number of start stop cycles based on the materials and method of construction, and the operating stresses due to centrifugal forces. This means that fans experiencing constant or regular speed changes will experience a reduced fatiguelife compared with fans that are run at constant speed.The fatigue life of fans operated under various speeds using VOD is difficult to predict, as it is dependent on the magnitude of speed changes, and the frequency, which will be varied to meet demand. It is important to be able to estimate remaining fatigue life to assist in maintenance planning and avoid unplanned maintenance activities.This paper will review extensive VOD data on fan operating conditions from two primary mine ventilation fans. This paper will demonstrate how this data can be used to calculate accumulated fatigue and predict the remaining fatigue life, and how this compares with fixed speed or non-VOD controlled fans.The increased maintenance costs for the impellers will also be estimated, and compared to the operating cost savings using VOD, to determine if the savings outweigh the additional maintenance costs.

Oct 12, 2022

"6.1. Mineralogical Techniques ApplicableTo the Platinum-Group Elements6.1.1. IntroductionThe named platinum-group minerals (PGM) usually occur as grains smaller than about 200 microns and, even when present as larger grains as in nuggets, these are often complex multimineral intergrowths. Therefore, the PGM must be examined by microscopic techniques and, because all named PGM are opaque, they are suitable for microscopic study by reflected light. Special techniques for concentrating PGM and preparing suitable polished sections are detailed in Chapter 5. Another characteristic of the PGM is that the majority have very high reflectance at 589 nm, i.e., over 450Jo, but they range from about 38 to 74%. In contrast, micro-indentation hardness has a wider range from - 60 to - 3,000 kg I mm, and the PGM range from brittle to malleable.The small grain-size of PGM imposes certain limitations, or complications, on the usual mineralogical determinative methods of reflectance, micro-indentation hardness and X-ray diffraction. In addition, certain combinations of elements in some PGM render electron-probe analyses difficult. The usefulness and shortcoming of these methods, as applied specifically to the PGM, are discussed in the following sections. These are not, however, meant to be exhaustive descriptions of the techniques, which are fully described in other texts.6.1.2. Micro-Indentation HardnessDetermination of the Vickers Hardness Number (VHN) is discussed in detail in recent publications, such as Bowie and Simpson (1977) and Craig and Vaughan (1981). In addition, the recommendations of the Commission on Ore Microscopy (COM) of the International Mineralogical Association (IMA) are given by Criddle (1980). The usual small grain-size of the PGM, however, precludes the widespread use of this technique and very few PGM have, in fact, had their VHN determined at the COM-recommended standard load of 100 gf (cf. Cabri, 1981b, in Chapter 7). Examination of VHN data reported in the literature reveals that the few PGM whose microindentation hardness has been measured have incomplete VHN data, measured with loads other than 100 gf (Chapter 7). The small grain-size may also result in unreliable VHN data because, even though the correct load may have been applied, a thin grain will give erroneous data due to the matrix, or the grain may even shatter or pop out of the section. On the other hand, micro-indentations may give useful qualitative diagnostic clues. Moncheite, for example, shows fractures near the indentation (Chapter 7, Plate 1). In other cases, intergrown PGM produce different-sized indentations: e.g., froodite-michenerite-gold in Cabri (1972); isoferroplatinumtulameenite in Cabri et al. (1973); michenerite-moncheite in Cabri and Laflamme (1976) and Chapter 7, Plate 1; altaitemichenerite- testibiopalladite in Hudson eta/. (1978) and Plate 1, Chapter 7."

Jan 1, 1979

By A. L. Engel

[Thi;. re:9ort presents re3ults of investigations of problema a3signed as ore-testing projects to the Ore-Dressing Section, t.fetal1urgica.l Div:biion, of the Bureau of Ii.fines at the .fississippi?Valley E>"'1lcrimcnt Station in rtolla, Ho., durine the fiscal year ended June 30, 1940.]

Jan 1, 1941

By Juel H. Stears

Research was done to determine if a hydraulically operated penetrometer developed by the Bureau of Mines could be used to estimate the roof-bolt anchorage capacity of mine roof rock. Tests were conducted both in the laboratory using cement cylinders and underground in shale rock. Hardness readings were measured by the penetrometer around the periphery of the bolt holes at the anchorage horizon. Roof bolts Nere then installed and subjected to an anchorage test. The results showed that the penetrometer readings could be used to determine the optimum stratum for roof-bolt anchorage but could not be used to make an accurate estimate of the anchorage capacity.

Jan 1, 1965

By Janice Zinck, Maziar E. Sauber

"To counter the recent uncertainty in the rare earths market, diversify the supply source, and help meet the future demand in this sector Canada initiated development of several new rare earth deposits. In the past few years, a number of various studies on rare earths plant design have taken place mainly covering process development, process selection, and flowsheet design. The purpose of this paper is to provide an overview of known domestic and potential resources and reserves of rare earths and their status quo with a focus on the metallurgical processes using the information available in the public domain. Plant designs currently under consideration in Canada are reviewed and evaluated. An outline of the areas of opportunity for selective innovation and technology development in the rare earths flowsheet development and the associated risks and rewards is provided.INTRODUCTIONThe rare earth elements (REE) have a very small annual market, but they are categorized as very strategic metals vital to global economic growth due to their indispensability to the development of modern defence system, green technologies and electronic applications. The International Union of Applied and Pure Chemistry (IUPAC) defines the REE as the 15 elements on the lanthanide series on periodic table of elements, plus yttrium and scandium. REE are classified as light rare earth elements (LREE; La to Gd), and heavy rare earth elements (HREE; Tb to Lu). Physical properties and chemical reactivity of yttrium is similar to those of HREE, thus it is categorized as such. Properties of scandium are not similar enough to classify it as either a LREE or HREE (Weng et al., 2015; Sappin & Beaudoin, 2015). However, the mining industry does not always abide to this definitive classification of the split between LREE and HREE. Therefore, in a comparative study of projects, there is a need to pay attention to how the elements are classified."

Jan 1, 2016

By M. Abdellatif

Successful demonstration of The Mintek Thermal Magnesium Process (MTMP) was achieved in November 2004 at the pilot-scale, About 30 tons of magnesium producing recipe was smelted in the DC arc furnace over a continuous operation of 8-days, Twenty-two furnace batching-tapping operations were carried out at a feed rate of 525kg/h and a smelting temperature of 1600-1700°C, The MgO content in the produced slag was as low as 6,7%, and averaged 9,2% MgO, resulting in an overall magnesium extraction of 77%, which reached 87% during good operating periods, Magnesium vapour was extracted at a rate of 70-85kg/h and was delivered to the condenser that was operated at 680-720°C, The magnesium was captured in the condenser crucible in a liquid state, allowing its prompt tapping, More than 3500kg of crude metal were produced over 15 on-line metal tapping operations, On average, a condensation efficiency of 85% was achieved during the entire testwork, which peaked at 87% during steady operations, The quality of the crude metal was similar to, if not better than, that of the Magnetherm's crude magnesium, A pre-feasibility study has indicated that the MTMP has the potential for lower capital and operating costs as compared to the electrolytic process, and therefore Mintek and its consortium partners are exploring opportunities for a commercial production facility.

Jan 1, 2006

By Leslie C. Thompson

The heap leach process used for recovering gold from oxide and sulfide ores is operated as a closed circuit system in which the cyanide process solutions are continuously recy­cled. In a well-designed operation there is little or no dis­charge of cyanide to the environment. Spent leached ore residues are water washed to remove most of the trace cyan­ides and precious metals remaining after completion of cyan­ide leaching. After the washing step, small amounts of cyanide, metal-cyanide complexes and nitrates remain in the residue. Most of the cyanide and nitrate residue constituents exist in the pore water of the spent ore rather than in the solid mineral fraction. More than 90% of the complexed cyanides in a freshly washed ore residue are present as free cyanide or weakly complexed metal-cyanides. Natural volatilization and decom­position rapidly remove most of these easily dissociable cyanides from the spent ore. Only the stable, strongly com­plexed metal-cyanides, such as gold, cobalt or the ferrocyan­ides and other constituents such as nitrates have a long term persistence in the spent ore residue (Towill et al). Despite washing and natural removal mechanisms, spent ore has the potential to act as a point source of com­plexed cyanides and nitrates for soil and groundwater con­tamination if inadequately contained (Huiatt et al). The groundwater contamination is caused by the leaching of the soluble cyanide compounds and nitrates from the pore water of the residue.

Jan 1, 1990