Search Documents

By R. H. Roberts

The Environment Weipa is located at 12° south latitude on the west coast of Cape York Peninsula, North Queensland, Australia. The climate is tropical with most of the 1 600 mm. average annual rainfall falling between November and March. During the short winter months (May/ August) the weather is clear and pleasant, with temperatures seldom exceeding 27°C.Throughout the remainder of the year, conditions are frequently oppressive due to consistent high ambient temperatures accompanied by high humidity. The terrain is of low relief, and generally not more than 6 to 10m. above mean sea level adjacent to the coast. The coastline features numerous short estuaries which discharge run-off from the heavy rains collected by creeks and rivers. The whole area is covered by an open forest, the predominant species of which is Eucalyptus tetradonta. These eucalypts have only limited commercial value and are heavily infested with termites. Despite the fact that Weipa is close to the location of the first reported sighting of the Australian coastline by a European (William Janz - 1606), it remains very isolated. There is no developed road or rail connection to centres of population, so that transport of practically all products, personnel and materials to and from Weipa is by sea and air. Cairns (population 49 000) is 580 km. by air and 670 nautical miles by sea; Brisbane, the

Jan 1, 1977

By H. Verakis, M. J. Sapko

The Pittsburgh Research Laboratory (PRL)1 of the National Institute for Occupational Safety and Health (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) Technical Support Center has devised a prototype hand-held instrument which can provide a direct assessment of the potential explosibility of a coal and rock dust mixture. Current Federal regulations require that rock dust be applied in all underground areas of a coal mine to mitigate the propagation of a coal dust explosion. To determine compliance with the Federal regulation, mine inspectors collect dust samples from sections of underground coal mines for an MSHA laboratory analysis of incombustible content. However, the laboratory analysis may not be completed for more than a week or two, during which time the mine area from which samples are taken may be inadequately protected. The operation of the Coal Dust Explosibility Meter (CDEM) is based on the difference in optical reflectance between light rock dust and dark coal dust. For a given coal volatility, the optical reflectance of such mixtures is relatively constant at the limit of explosibility, independent of the coal dust particle size. The CDEM is not intended to replace the current MSHA laboratory analysis of coal mine dust samples for incombustible content, but to serve as a supplemental device for enhancing mine safety through improved rock dusting practices.

Jan 1, 2006

By William L. Crentz

This Investigation of the preparation characteristics of the coals in Armstrong County, Pa., is the third in a series of Bureau publications by counties appraising the practicability of upgrading marginal deposits to metallurgical standards. Earlier investigations covered the washing characteristics of the coals occurring in Cambria County, and the principal reserves remaining in Indiana County. In Armstrong County, the Upper Freeport bed is the major source of production, the Lower Kittanning bed being of secondary importance. The Lower Freeport bed is mined to some degree, but it is usually too thin and spotty in occurrence to support large-scale operations. The remaining production is taken from the Pittsburgh, Middle Kittanning, and Upper Kittanning beds, but the quantities are insignificant. Table 1 shows the county's coal production) by beds, during 1948. The coals of Armstrong County are not generally considered to be of metallurgical quality because of the high sulfur content. The raw coals usually analyze more than 2 percent sulfur, and more than 4 percent sulfur is not uncommon, especially in the Lower Kittanning bed.

Jan 1, 1951

By Nan Zhou, Jixiong Zhang, Qiang Zhang

"Mining activities under hard roof could easily induce rock burst. Based on the geological conditions of widespread hard roof in China, this paper discusses the type, mechanism of occurrence and prevention of rock burst caused by hard roof from energy evolution point of view. It analyzed the interaction between the solid backfilled body and roof under different backfilling ratios. And by establishing and applying the mechanical model, the deformation of hard roof and energy evolution of the panel under different backfilling ratios were determined, revealing the control effect of solid backfilling on disaster-causing energy. As a result, an innovative method using the solid backfilling method was proposed as a solution to the hard-roof-induced rock burst hazards. Moreover, mine trial was conducted in Panel 6304-1 of Jisan Mine. The result shows that the stress concentration factor of the front abutment stress was only 1.44; the coal dusts in drill holes didn’t exceed the limits and microseism of large energy didn’t occur during mining mining, indicating that solid backfilling mining could be applied as an effective method for preventing rock burst caused by hard roof.INTRODUCTIONSHard roof refers to the thick strata above the coal seam or thin immediate roof. It is strong with poor joint development. After mining, instead of immediate caving, it will overhang for a large area in the gob, resulting in high stress in front of the face and difficulty in gas dispersion. As a result, the face spalls, the roof exposes and the gas accumulates in the gob. With the continuing advance of the face and increase in area of overhang, the stress in the hard roof will eventually exceed its ultimate strength and cause a large area of caving, followed by quick release of energy concentrated in the roof and coal seam, which may cause rock bursts and other dynamic disasters in the mine as well as serious equipment damage and casualties. Therefore, the hard roof becomes one of the main factors causing rock bursts at the face.Hard roofs in China varies in conditions. It ranges from dozens of meters to hundreds of meters in thickness. However, coal reserve under hard roofs accounts for about 1/3 of the total reserve; moreover, nearly 40% of the fully-mechanized coal mining panels are those with hard roofs and more than 50% of the mining areas are associated with problems of hard roofs. Aiming at this problem, researchers at home and abroad have proposed many solutions, e.g. coal pillar support, strength weakening and forced caving, to prevent rock bursts caused by hard roof. These solutions have been employed in some cases with good results. However, due to the variability in geological conditions of mining and hard roofs, the application of the above solutions is limited."

Jan 1, 2015

By C. R. Dale

IT IS the purpose of this paper to point out a number of the most common causes of crooked holes; to outline methods of drilling and straightening which to my personal knowledge have proved successful in numerous cases; to describe some of the characteristics of holes which, though not crooked in an exaggerated sense, may still cause serious mechanical trouble if not recognized and properly remedied; and to define clearly the part of oil-well surveying in the concerted effort operators generally are making to keep their wells straight from spudding to completion

Jan 1, 1931

By Frank D. Lamb

"INTRODUCTION The use of beryllium and its alloys has come into prominence in the last 15 years and increased considerably during the war. In contrast to other light metals, such as aluminum and magnesium, beryllium is relatively hard, has a high melting point (1,285° C.), and other properties that make it resemble steel in many respects. It has a specific gravity of 1.85, is only slightly heavier than magnesium (specific gravity 1.74), and is appreciably lighter than aluminum (specific gravity 2.7). Its lack of ductility prevents its use as a structural material, but this difficulty may be overcome in the future by the use of various alloy forms. The only important commercial alloy in which beryllium is used today is with copper. The addition of small percentages (1/2 to 2 percent) of beryllium to copper imparts properties to the alloy that make it desirable for use in springs carrying electrical current, particularly at high temperature. Many other uses of berylliam are known, and new uses are being found constantly that make the metal of increasing interest.Possibly the main factor preventing the use of more beryllium is the lack of a large source of beryllium ore. Many beryllium minerals are found as minor constituents of natural deposits, some of the more common ones being beryl (Be3Al2(Si03)6), chrysoheryl (Be A1204), helvite (3(Mn, Fe) Be Si04. MnS), and phenacite (Be2Si04). Of the known beryllium minerals, beryl is by far the most common and has been found distributed rather widely throughout the world. It usually occurs associated with granitic rocks and is commonly found as a constituent of granitic pegmatite."

Mar 1, 1947

By D. Bernabe

The mine scheduling process defines a mining sequence across the life of the mine and stipulates the amount of ore, waste, and specific blocks to be mined each year so that the highest economic return can be obtained under a number of constraints. There are a number of mine scheduling software packages available. Each claims to be the best scheduler by maximizing Net Present Value (NPV) or by minimizing overall mining costs. These mine scheduling programs follow different procedures and scheduling philosophies based on either mathematical or heuristic principles. There was no study in which the mine production scheduling procedures applied by these packages were discussed and compared. This paper evaluates four open pit mine scheduling programs recently developed and compares them in order to determine if significant differences exist among them. The same input data, which consist of a 3-D block model, an economic set of parameters, and the initial surface topography for a operating copper mine in Southern Peru, was used to test each technique. The following programs were investigated with respect to their ability to optimize the NPV for the case study. 1) M821V1 Scheduler by Mintec; 2) NPV Scheduler by Earthworks; 3) Milawa Scheduler by Whittle Programming; and, 4) Fundamental Tree Scheduling Method (FTSM) developed at the Colorado School of Mines. The results from this case study demonstrate that the scheduling software packages, Mintec, Earthworks, and Whittle obtained similar NPV’s, while FTSM scheduler gave a six percent higher NPV than the other schedulers.

Jan 1, 2002

By G. R. Hopkins

For several years prior to about the middle of 1928 both the number and capacity of natural-gasoline plants showed a steady increase; this resulted from a material gain in the supply of casinghead has due to the discovery of a number of flush fields with relatively high gas-oil ratios. From 1928 to date some form of proration has been continually in force, with a consequent curtailment in the supply of wet gas. This decline in available gas and a severe decrease in prices, due largely to the increasing competition of light refinery products, has eliminated virtually all of the weaker units during the last 5 years, with the result that the number of plants declined from 1,155 on January 1, 1928 to 19035 on January 1, 1930, to 909 on January 1, 1932, and then to 859 on January 1, 1934, The struggle of the small high-cost producers to exist is illustrated further by the trend in the number of shut-down plants, which has increased from 36 on January 1, 1930 to 100 on January 1, 1932 and to 128 on January 1, 1934. The increase in the number of plants prior to 1929 resulted in a material gain in the total capacity, but the decline in number between 1929 and 1932 was not followed by a corresponding decrease in capacity, as gains resulting from the construction of a few very large plants overbalanced the loss due to the dismantling of a large number of small ones. However, the low prices of 1932 and 1933 supplied little incentive for new construction, and the total capacity declined in approximately the same ratio as the number. Thus the total capacity declined from 11,387,000 gallons daily on January 1, 1932 to 13,060,000 gallons daily on January 1, 1934, Of the latter 9,181,000 gallons (91 percent) represented the capacity of the operating plants and 679,000 gallons (9 percent) the capacity of the idle plants.

Jan 1, 1934

By Kíssia Carolina Bertoluci Cardoso

Para a fabricação de peças de grande porte, o forjamento em matriz aberta é o processo mais utilizado. Porém, se seus parâmetros não forem bem estabelecidos, defeitos metalúrgicos poderão surgir; esses, em sua maioria, provindos do material bruto de fusão, como rechupes e vazios. Para sanar tais defeitos, a deformação imposta na peça deve ser a mais homogênea possível. Neste estudo, a simulação numérica foi utilizada para verificar a relação entre a largura de contato matriz-peça e a espessura da parede de peças vazadas, com o objetivo de analisar o conceito de razão de mordida para esse tipo de geometria. Utiliza-se um billet cilíndrico inicial de 450 mm de comprimento, 360 mm de diâmetro externo e 120 mm de diâmetro interno, de material AISI 4140. As razões de mordida estudadas variam entre 0,2 e 1,4, sendo impostas variações de tempo em cada processo. Após análise, pôde-se verificar que as geometrias que apresentam distribuições mais homogêneas de deformação utilizaram razão de mordida de 0,4.

Aug 16, 2017

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed, to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke regardless of preparation. This report is one in a county series that describes the preparation characteristics of the coals of Mingo County, W. Va.

Jan 1, 1956

By R. Bitmead, R Barker, A. Drake

The opencut coal mine is located about 50 km west of Brisbane, the capital city of Queensland in Australia and produces about 140 000 tonnes per annum of high grade steaming coal utilising a small team (ten) of personnel to mine remnants of the Aberdare and Bluff seams left by previous underground mining. This, in itself, is not remarkable except that one of the seams has commenced spontaneously cornbusting resulting in temperatures in excess of 55’C commonly being encountered with portions of the p’it being wreathed in steam. To extend mine life, the mine required a blasting system that would: . Safely blast in temperatures below 100°C . Significantly reduce overall unit costs . Not increase the current vibration impacts on nearby housing . Not increase flyrock.

Jan 1, 2002

By A. Peake

Background The CSIR Division of Mining Technology assumed responsibility for the operations of the Hoist Rope and Mechanical Test Laboratories at Cottesloe in April 1999. The laboratories were previously the responsibility of the CSIR’s Division of Manufacturing and Materials Technology, before which they fell under the National Mechanical Engineering Research Institute (also of CSIR). As the focus of this conference is on safety in mines research institutes, it was thought appropriate that this paper should review some of the activities at Cottesloe and its role in supporting mine safety strategies.

Jan 1, 2003

By R. A. Nemchek

Over the years, concentrator plant design has evolved from a large number of small grinding mills to a small number of large mills. In many cases, all of the tonnage runs through a single mill (typically a large SAG mill), so that the plant?s performance hinges on the productivity of this one machine. Industry specifications attempt to address the critical nature of today?s grinding mills in a manner that is often overly complex, neglects economics, and is not clearly focused on the end user?s goals. This paper surveys current industry practices, and proposes an improved approach to standards writing recognizing that product design, procurement, manufacturing, and quality are all inter-related in contributing to a project?s success. The lessons learned here can be extended to specifications for all types of machinery.

Jan 1, 2012

By Mine F. J, Woods P. H

The Top End of the Northern Territory lies in the monsoonal zone and receives rain during the November-April period. Initially, at the start of the wet season, rain storms are localised, but, following the descent of the monsoonal trough from below the equator, widespread rain occurs. Overflow incidents at mine sites tend to arise midway through the annual wet season when excess water accumulated in ponds begins to discharge to the external environment. Remote-access monitoring may be undertaken at mine sites using equipment to continuously measure water quality parameters with storage of the information on a data logger. The data is then retrieved by visiting the site and transferring it to a portable computer or by remotely accessing the system using a telemetry system and transmission via telephone, VHF/UHF or satellite. Such systems are readily available and vary in cost depending on the sophistication of the data transfer system. Available sensors for continuous monitoring include those for conductivity, temperature, pH and other ion selective electrodes, eg nitrate, and water level. Of these variables, conductivity is most useful due to its inherent accuracy and stability of reading. Remote monitoring capability is able to provide: (i) more intensive monitoring of key issues; (ii) more timely information; (iii) correct perspective on the degree of environmental problem; and (iv) information from remote locations, which would be difficult to monitor by more conventional methods. Examples are given for applications of continuously logged measurement of conductivity of waters discharging to drains and in creeks at Pine Creek, Ranger, Nabarlek and Woodcutters mines in the Northern Territory. These applications demonstrate the timeliness of the continuous monitoring technique.

Jan 1, 1994

The outlook for suppliers of energy to the expanding economies of the Pacific Basin region is essentially positive, but particularly for exporters of high quality steam coal. This paper argues that economic growth in the Pacific Basin region has exceeded world economic growth for some years and that this will continue to be the case for the next decade at least. It looks briefly at the link between economic growth and energy demand and at the relationship between energy demand and the demand for electricity.Changing preferences in fuel mix for electrical generation in the region are noted and tentative forecasts made about variations in this mix. The pros and cons of various forms of fuel used to generate electricity are considered from the point of view of the consumer.

Jan 1, 1990

By Jim Ploger, Peter W. Johnson

Bus drivers represent a large segment of the US transportation industry and research has shown an association between exposure to Whole Body Vibration (WBV) and the high rates of low back disorders. Impulsive WBV exposures have been recognized as a risk factor for low back injury and new guidelines exist for their measurement and assessment (ISO 2631, Part 5). Methods to accurately and better characterize the impulsiveness of WBV along with the temporal patterns of the exposures are needed. The development of a hardware and software system to measure continuous TWA and raw, impulsive WBV exposures and the design of a subsequent study are presented. Methods Using two Larson Davis HVM 100 as accelerometer amplifiers, small external batteries, and a Pocket-PC (PDA) with 1 Gb of compact flash memory, we can collect up to 16 channels of data for a full day 600 Hz. Tri-axial WBV exposures will be measured and characterized at the frame of the bus and at the driver/seat interface (seatpad accelerometer). Using a repeated measures design, 20 bus drivers will drive on selected routes which include both city streets and highways, and within and between subject components of variability and exposure determinants related to the bus, bus seat, the bus driver, and the route will be identified. Global Positioning System (GPS) data will also be collected and integrated with the WBV exposure data to facilitate the identification of the location, velocity and type of road associated with high average TWA and impulsive WBV exposures. This system may be used to develop administrative (alter speed and/or route of bus, systematically vary type of routes) and/or engineering controls (identify and trigger the need for street repair) to reduce high WBV exposures. Results Our portable Pocket-PC based data acquisition system is up and running and we can collect seven channels of WBV data (seat pan tri-axial accelerometer, bus frame tri-axial accelerometer and GPS data) continuously for a full shift. The software analysis of the data is complex but nearing completion. We have incorporated the vibration dose calculations from ISO 5321, Part 5 and have obtained a Matlab-based routine to appropriately weight the continuous signals. Discussion In summary, the measurement of WBV is complex but new technologies open avenues of collecting and assessing WBV exposures that were previously not possible. The standardization of impulsive WBV exposure assessment methods is needed to further the discipline and better enable comparisons across studies.

Jan 6, 2006

By H Allday

The mining industry’s attention has shifted over the last decade with the recovery from the downturn resulting in greater development of innovation and new work methods in a bid to remain competitive and deliver higher productivity. The emphasis on cost reduction to improve profit margins has primarily been the focus of the “work smarter” campaigns embraced within the industry. But is this strategy holistically the best-for-business, or does it place a ceiling on revenue opportunities and inhibit mining companies from truly maximising value? Businesses need to maintain a balance between active cost management and revenue generation often resulting in cost reduction strategies at site level. These strategies have merit, assessing areas of cost wastage across operations and creating space for opportunity. However, this potentially can create distractions from the goal of enabling growth and lead to the sacrifice of quality and delivery. Focusing too heavily on cost reductions without addressing revenue generation is an unprofitable lens to look through, and the relationships between cost, revenue, quality and profit margin can often be overlooked resulting in missed opportunity to maximise value. How these relationships are effectively employed by mining companies to reap the rewards from an overarching corporate perspective down to site level remains a fluid concept depending on the nature, operating market and strategy of the business. A common directive from businesses to their operations is to strive for greater profitability and productivity. The quantification of these requirements, and the nature of the cascading message delivered, impacts the methods employed by the operational team to meet the expectations of the business. Cascaded strategies, if not delivered with appropriate participation and buy-in can often be perceived to be knee-jerk and create frustration for operations who are squeezed to deliver on expectations by slashing site costs. This squeezing is not only felt by the mining operation but at the individual level and can result in increased team stresses. In some cases, this may also steer behaviours towards activities that result in corner cutting and an elevation of operational risk, potentially increasing associated incidents and injury. Driving down costs by any means can create an unhealthy tunnel vision where value is no-longer assessed for best-forbusiness results. By flipping the viewpoint to a value-based approach revenue opportunity may be realised and potentially exceeded, however this opportunity may be missed if value is over shadowed by a cost heavy focus. By analysing a selection of real operational cases (ranging from mining contractors through to in-house mining giants), it becomes apparent that practical revenue maximisation strategies are not only key to an increase in value and cash flow but to a stronger understanding of business drivers for sites and operators alike. In the cases evaluated additional revenue opportunities are foregone in favour of cost reduction strategies resulting in negative impacts on the associated operations and wider businesses. Alignment towards value generation is king. If strategies are not implemented focusing towards value and revenue maximisation, the opportunity loss experienced by mining operations could continue be great and the question should be posed; when the next up-turn hits will operations be ready to reap the rewards or still have a glass ceiling above their heads?

Mar 15, 2021

By Wen-Ming Chien

Keywords: AN-KN Phase Transition, Lattice Parameters of AN-KN, X-ray Diffraction The lattice parameters of the low and high temperature phase of KNO3-rich (in NH4NO3) solid solutions have been determined by the X-ray diffraction method. The low temperature single KNO3 phase (KN II) are from 92%-100% KNO3 in NH4NO3 composition range and from room temperature to 393 K showing in X-ray diffraction patterns. The high temperature KNO3 phase (KN I) showed very broad composition range between 20% to 100% KNO3. The lattice parameters of KNO3-rich (KN II and KN I) solid solutions have been calculated at different temperature range. The volumes of orthorhombic KN II phase decrease from 0.3208(3) to 0.3195(3) nm³ at the room temperature as the compositions increase from 95% to 100% KNO3. The lattice constants of the hexagonal KN I phase show that there is no significant change in a-direction when the temperature increases. Details X-ray results and lattice expansion equations during heating will be presented.

Jan 1, 2005

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By S. F. Böde, K. Böde

This paper focuses on developing a comprehensive and pragmatic information technology (IT) strategy for low-margin construction activities. This forms part of the realignment of the general business strategy, and refocusing the operational model. The main elements of the IT strategy formation are analysis of the current IT environment in terms of software and hardware, carrying out a gap analysis, and developing individual functional digitalisation strategies in construction execution based on Building Information Modelling (BIM), business administration processes, communication, business intelligence (BI) and reporting, and data security. Further, substantial emphasis is given to the sustainable strategy implementation in terms of hardware and software readjustments, their integration, user training, and defining the way forward.

Sep 1, 2021