Search Documents

By R. A. Gee, G. B. Ashton, S. T. Warren, P. N. Groves

Northside Storage Tunnel provides 500 megalitres (Ml) (130 million gallons) of storage capacity to capture stormwater/sewage overflows into Sydney Harbour. The6.6 m diameter TBM driven tunnel traverses Middle Harbour 85 m (280 ft) below sea level and through a sandstone/shale rock mass, highly disturbed by stress relief, 20 m(65 ft) beneath the base of the sediment filled palaeochannel. Target limits for inflow, groundwater drawdown and settlement of the valley beaches were achieved by systematic forward grouting from the TBM. Support included rockbolts, sets and shotcrete to carry rock loads, control block instability and spalling and to provide durability and serviceability. This paper describes the tunnelling and grouting works and their effectiveness.

Jan 1, 2001

By Forrest T. Moyer

Need for lightweight building materials was created in the latter part of the nineteenth century by a radical change in building design in which dead load or structural weight was transferred from thick, heavy, load- bearing walls of former construction practice to a load-carrying framework of beams and columns with thin walls. This new design was brought about by the introduction of structural steel followed by reinforced concrete and structural concrete as materials for the erection of the load-supporting frame. The new materials and method of construction made possible the erection of skyscrapers and the building of bridges with long spans, and made feasible additions of one or more floors to existing buildings. As size and design of the load-bearing framework are controlled chiefly by dead load, the natural result was a. search for and use of light- weight materials in partitions, floors, and exterior walls. However, these thin walls created problems of heat and sound. insulation, so that building materials which possessed good heat- and sound-insulating properties in addition to light weight were objects of extensive research. One group of materials developed to fill this need comprised lightweight concretes, of which some were obtained by the use of lightweight aggregates. Although the advantages of lightweight.materials were evident from the first skyscrapers, there was a transition.stage.between the old bearing- wall and modern skeleton-frame types of building, with the heavy and massive construction of the former superimposed upon the latter. Hence, it was not until the period between 1910 and 1930 that the new lightweight concretes were recognized and used more extensively in the erection of large, nonresidential buildings. From this type of construction, light- weight-aggregate concretes entered-fields of residential and small non- residential building; in which they were found desirable for production of prefabricated, large-size; masonry units. Although the weight of each unit was reduced sufficiently to enable one man to handle it easily, properties of the new concretes other than light weight were the principal factors in the ready acceptance of these new materials in residential building. Manufacture of precast units includes complete lines of masonry and back-up blocks, bricks; floor beams, columns and partition, roof, and floor tiles and slabs. Recent improvements in casting machinery, development of the vibration-pressure machine, and a more thorough study and knowledge of the requirements and properties of the concrete mix have all contributed materially to the rapid expansion in use of lightweight aggregates in this industry.

Jan 1, 1942

The main orebody of the Bodangora mine is a metalliferous quartz reef within a major fault plane in the strongly folded and faulted volcanic rocks of the Ordovician-Silurian Oakdale Formation. The similarity of the type of mineralization to that of other pyrometasomatic deposits in this area suggests that the mineralizing fluids originated in the nearby Wuuluman Granite.The associated Mitchell's Creek West or Dick's reef is discussed briefly.

Jan 1, 1970

By F. W. Gray

A GEOLOGICAL study seeking to determine, for economic purposes, the value of the Sydney coalfield as a source of coal supply. Limitations of the coalfield come under two main heads: (a) Areal extent of the undersea coalfield. (b) The distance from shore at which coal can be mined at a cost of production permitting its profitable sale. Conclusions reached are that the areal extent of seams below the Phalen seam is of. small economic importance, and that non-persistence of these seams in full thickness and quality in the undersea extension of the coalfield will put an end to profitable mining before any limitations connected with distance from the shore-line become operative. With respect to the Phalen seam, non-persistence or deterioration of the seam will become effective in the western part of the coalfield, and less certainly in the eastern part of the coalfield, before operation of limitations by distance from shore. In the central portion of the coalfield, the seam probably persists in commercially workable thickness and quality to beyond the limit of mining set by distance from the shore-line. With respect to the seams above the Phalen seam between the Mountain fault on the extreme western boundary of the coalfield and the assumed termination of the deposition area on the eastern extremity of the field near South Head of Morien, there appear to be only such limitations as arise from engineering approach, distance from shore, sufficiency of strata cover between the sea-floor and the upper coal seams, and quality of the coal (with certain reservations as to the continuity of the upper seams under Sydney harbour and in the Sydney Mines-Little Bras d'Or district). Some of these seams have fragmentary land outcroppings from which their persistence seaward is assumed, and there may be other and still higher seams in the strata column which are entirely submarine.

Jan 1, 1941

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert system shells designed for real-time processing plants that also included the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. Significant performance increases have been achieved using these systems, but in general, they suffer from the static nature of their rules and to a degree the process models also. Typical improvements quoted in the literature suggest throughput rate increases of 4 to 8 percent and recovery increases of 1 to 4 percentage points. In over 30 years of designing and installing expert systems we have never seen performance numbers less that these but have often seen numbers in excess of the high values. However, once the system has been installed and tuned up the performance usually does not improve much thereafter. Granted, the initial increases in throughput rate and recovery are significant but a question always lingers, that is, can the expert strategies be modified further to squeeze a little more improvement out of the system. The answer to this question is a resounding yes, however a complete understanding of what we do well as designers and operators of expert control systems is required as well as how we can improve upon our best practices is required to move us from the performance plateau we have been on for a number of years to a new higher level of performance.

Jan 1, 2009

By A. C. Fieldner

THE Bureau of Mines has received many requests for Information concerning the methods its laboratories use for analyzing coal and coke and determining their heating value. The fuel investigations now conducted by the Bureau of Mines are an outgrowth of the work undertaken at the Government coal-testing plant erected in 1904 at the Louisiana Purchase Exposition in St. Louis, and the methods for proximate and ultimate analysis of coal used by the Bureau of Mines are based on those originally adopted by the chemists of the coal-testing plant and followed in the subsequent chemical work of the Government fuel-testing plants at St. Louis, Mo., Norfolk, Va., and Pittsburgh, Pa. The many valuable suggestions and criticisms received from N. W. Lord, director of the School of Mines, and from E. E. Somermeier, professor of metallurgy, of Ohio State University, at that time, are greatly appreciated; development of many of the methods for the proximate and ultimate analysis of coal now used by the Bureau of Mines is chiefly clue to these men.

Jan 1, 1951

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

By M. Kalin

"SUMMARYWaste management in general, and the water treatment of mine and mill effluents, has become an ever increasing burden for mining operations. A reduction in these expenditures would undoubtedly be desirable if this could in fact be achieved within effluent guidelines and monitoring requirements.A brief summary is presented of the research which has as its aim the development of methods which would reduce such costs and lead to solutions for environmentally acceptable close-out conditions for acid generating mine waters. The basic concepts of Ecological Engineering and Biological Polishing are presented, together with an indication of the present state of these research efforts. Details are provided of the progress of various experiments which aim to promote reducing conditions, organic matter production and the establishment of biological filters which remove metals from the water which are then retained within the waste management areas. These conditions should lead to a curtailment of acid drainage and an improvement in effluent quality.A description is provided of the first pilot demonstration using this approach to achieve a walk-away condition for the close-out of a massive sulphide tailings resulting from 10 years of operating a copper/zinc concentrator in Northern Ontario.1.0 INTRODUCTION1.1 Waste management and close-outIt is recognized that the achievement of a cost-effective and competitive mining operation, from the commencement of exploration for ore bodies through to the day-to-day efficient operation of the mine, requires a certain expertise and sophistication. However, the environmental effects of these activities are considered peripheral issues and their importance as an integral part of the planning and development of the mine/mill, is not always appreciated."

Jan 1, 1988

By Jack G. Gill, Richard A. Dick

Blasting safety is a subject that cannot be overemphasized. Two years ago, a study was published describing g a series of fatal blasting accidents which took the lives of ten metal and nonmetal miners during the period of May 1973 to August 1974.1 Each accident was described, and the direct causes were delineated. In each instance, specific MESA safety regulations were violated. Four of the victims were killed by drilling into explosives; two were killed by lingering too long in the vicinity of fuse rounds; two fatalities resulted from improper guarding of shots; one blaster did not retreat far enough to avoid the blast concussion; and another used an improper tester for checking an electric blasting cap. All of these fatalities could have been avoided by adhering to the MESA blasting regulations contained in 30 CFR Part 55 (Health and Safety Standards-Metal and Nonmetallic Open-Pit Mines), Part 56 (Health and Safety Standards-Sand, Gravel and Crushed Stone Operations), and Part 57 (Health and Safety Standards-Metal and Nonmetallic Underground Mines).

Jan 11, 1977

By Mike Cammack, Logan Huppert, Gustavo Azpilcueta

During the summer of 2015, Unisea Inc. sought proposals for the G1 Dock Replacement Project in Dutch Harbor, Alaska. It would be a one year project and construction was scheduled to begin in the spring of 2016. One aspect of the project was the requirement for a layer of armor stone to protect part of the dock. An estimated 30,500 tonnes (37,670 t) of armor stone were needed for the project. The source of rock was the Unisea Quarry due to its proximity to the project and the quality of the stone meeting all the required technical standards.

Jan 1, 2018

By A. B. Cecala

Video technology coupled with data logging exposure monitors have been used to evaluate worker exposure to different types of contaminants. However, previous application of this technology used a stationary video camera to record the worker?s activity while the worker wore some type of contaminant monitor. These techniques are not applicable to mobile workers in the mining industry because of their need to move around the operation while performing their duties and tasks. The Helmet-CAM is a recently developed exposure assessment tool that integrates a person-wearable video recorder with a data logging dust monitor that are worn by a miner in a backpack, safety belt, or safety vest to identify areas or job tasks of elevated exposure. After a miner performs his or her job while wearing the unit, the video and dust exposure data files are downloaded to a computer and then merged together through a NIOSH-developed computer software program called EVADE (Enhanced Video Analysis of Dust Exposure). By providing synchronized playback of the merged video footage and dust exposure data, the EVADE software allows for the assessment and identification of key work areas and processes, as well as work tasks that significantly impact a worker?s personal respirable dust exposure. The Helmet-CAM technology has been tested at a number of metal/nonmetal mining operations and has proven to be a very valuable assessment tool. Mining companies wishing to use this technique can purchase a commercially available video camera and an instantaneous dust monitor to obtain the necessary data, and the NIOSH-developed EVADE software will be available for download at no cost on the NIOSH website.

Feb 27, 2013

By Reginald N. Boryor, Steven D. Woods

1.0 Introduction ?Low grade, high tonnage, open pit gold mine. ?Gold bearing Tarkwaian conglomerates. ?Reverse Circulation percussion drilling (25m X 25m grid). ?Composite 1m intervals, logged and split in the field to provide±2Kg samples. ?Samples used to build grade control block models using SURPAC. ?Approximately 100,000-130,000 meters drilled per year. ?RC samples are assayed using Rapid Cyanide Leach (RCL). ?Check assays are done using Fire Assay

Jan 1, 2005

By Francis J. Fratttali, Verda McLendon, Stanley J. Green

"INTRODUCTION During the first phases of the war emergency the shortage of aluminum prompoted the Bureau of Mines to investigate methods for using low-grade bauxites of high silica content and also clays as raw-material sources of this strategic metal. The Bayer process treats low-silica bauxites to provide the industry with a major portion of the purified alumina, which contains very low percentages of silica and other impurities. One of the methods investigated in the laboratories of the Bureau of Mines for low-grade materials is the lime-soda sinter process, which was studied on a pilot-plant scale. In this process, the alumina content of the alumina-bearing minerals Bs made water-soluble by sintering the raw material with limestone and soda. Simultaneously, the siliceous material is rendered insoluble. The sinter is extracted with an alkaline liquor, and the resulting extract liquor is treated as follows to recover the alumina: (1) Autoclaving with lime to remove silica as a zeolitic complex and (2) treatment with CO2 to precipitate alumina as the trihydrate (A1203.3H20). Figure 1 is schematic flow sheet of this process.As the process is cyclic, it is necessary that nearly all of the soda and alumina remaining in the plant liquors after carbonation be recovered. Upon passing through one cycle, these liquors contain 14 to 15 percent NaCO3 2 to 5 percent NaOH, 1 to 3 percent A1203, minor amounts of silica, and, with certain materials such as Pennsylvania diasporic clays, 0.5 to 1.0 percent Na2S04. Approximately 50 percent of the Na20 in these liquors must be returned, as soda ash, to the dry-grinding and raw-materials blending operations. Previous work (6)5/ on sulfate-free solutions demonstrated that two methods for recovering Na20 were feasible, namely: (1) Salting out Na2C03.H20 by evaporation of the carbonated solutions and (2) crystallizing Na2C03.10H20 by cooling the concentrated carbonated solutions."

Sep 1, 1947

By V. F. Parry, W. S. Landers, John B. Goodman

"INTRODUCTION The object of this investigation was to demonstrate a satisfactory method of storing slack subbituminous coal in open pits in a manner,that would minimize the cause of the physical deterioration and would have a practical application.The storage of coal by industrial plants is to their advantage, since an adequate operating supplying of fuel is available at all times as insurance against transportation delays, shortages, and strikes. Furthermore, it is possible to participate in low seasonal freight rates and mine costs by permitting the railroads to utilize idle equipment and by taking advantage of the off-peak production at the mines. For a number of years, one of the larger beet-sugar companies operating in the Rocky Mountain region has taken advantage of the lower prices and seasonal production of subbituminous slack coal during the summer months and purchased a large proportion of its requirements for the annual winter campaign. This company, operating sugar-refining plants in the 1943 campaign, used 256,613 tons of subbituminous coal. Of this quantity, 166,636 tons was purchased during the off-peak season and stored for use during the winter. It is the practice of this concern to place coal purchased through the months of January to October in underwater storage for use in the beet-sugar campaign, which lasts from October to as late as, January. The beet-sugar refining ""campaign"" period starts immediately after the beginning of the beet harvest and lasts 60 to 70 days."

Aug 1, 1946

Many mining operations are uncertain of what costs they should be achieving. The majority of cost estimates are based on historical costs that have added contingency factors. Historical costs are a valuable source of information but a more precise costing method is necessary. There are several alternative methods for predicting costs. A methodology which provides the best indication of the achievable costs is one using a standard inventory list and a bill of quantities. The model is termed a Basic Principles model and addresses basic design principles and engineering constraints.

Jan 1, 1990

By X Dahe

SLon vertical ring and pulsating high gradient magnetic separators (VPHGMS) possess the advantages of high efficiency and high reliability in beneficiating weakly magnetic minerals. In recent years, models SLon-2250, SLon-2500, SLon-3000 and SLon-4000 have been developed. This paper gives several examples of their applications in oxidised iron ore and ilmenite processing flow sheets to improve iron and ilmenite recoveries.CITATION:Dahe, X, 2017. Recent development and application of SLon vertical ring and pulsating high gradient magnetic separators in the iron ore and ilmenite processing industries, in Proceedings Iron Ore 2017, pp 461–466 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

"D bed, Ky., coaL, washing characteristics RII 5140coking coal, reserves, estimate RI 5037Pa., coal, washing characteristics RI 4834, 4941D bed mine, Ky., coal, washig characteristics"

Jan 1, 1960

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace-time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200-foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace- time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200- foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

A simple process for making filter aids from coal by controlled carbonization at 800-1200·C is described.Several possible variations in reactor design have been used experimentally, involving fluidized beds of carbon or inert material, reaction of the particles while entrained in air, and a combination of entrainment and fluidization.Product yields depend upon the composition of the parent coal but are always less than the sum of the ash and fixed carbon values determined by the proximate analysis. The product yield also depends on the air-to-coal ratio, which affects the amount of coal substance burned and the temperature attained. Particle residence time and reactor temperature affect the degree of devolatilization of the product and hence its wettability. The filtration behaviour of carbonaceous filter aids is greatly influenced by the size distribution, shape and physical properties of the particles-parameters which are largely determined by fue type and particle sizing of the coal used.Carbonaceous filter aids are distinctly different from other types commonly used and extensive industrial applications are anticipated in a wide range of industries ranging from food to mineral processing.

Jan 1, 1970