Search Documents

By Sushant Upadhyaya, Deniz Karadeniz

As part of the widening of I-64 in Williamsburg, Virginia, an extensive subsurface exploration program consisting of Standard Penetration Tests (SPT), Cone Penetration Tests (CPT), Dilatometer Tests (DMT), and Vane Shear Test was performed. In addition to these in-situ tests, an extensive laboratory testing program was completed including Consolidated-Undrained Triaxial, Unconsolidated-Undrained Triaxial, Direct Shear, and consolidation tests. The strength and the compressibility properties are deemed conservative for Yorktown and St. Mary’s Formations when evaluated based on the current topography, the existing overburden pressure and SPT values. SPT exhibited low blow counts especially within Yorktown Formation due to the increased excess pore water pressures resulting in a localized liquefaction at the tip of the split spoon sampler corresponding to remolded or fully softened strength of the soil. Therefore, the applicability of the SPT correlated soil parameters somewhat leads to conservative designs with deeper piles to achieve a desired structural load demand. Generally, the in-situ estimated soil design parameters are found to be comparable with the laboratory test results corresponding to long-term resistance gain with time. It is of practical importance to employ realistic soil design parameters for design applications such as pile foundations to provide cost and schedule savings. This paper presents a discussion on the soil strength estimates and variability from in-situ and laboratory tests for realistic strength characterization of Coastal Plain deposits.

By Thierry Bernard, Guy Gagnon

Blasting at very close proximity to urban areas is typically a situation where both local communities and mining stakeholders get nervous. The context becomes logically even more tensed when the blasting operations have to be performed above an old underground mine. When mitigating subsidence risks requires firing the largest possible shots, the nuisance control (flyrock, vibration, and noise) required by local and national regulations, contrarily urge for being more conservative.

Jan 1, 2014

By C. E. Jordan

The fundamental properties of dielectric separation were studied to provide insight into the design and operating characteristics of a dielectric separator. Force equations on mineral particles were derived and evaluated experimentally. Responses to variations in the electrical voltage and frequency, feed rate, particle size, dielectric fluid, and dielectric constant were tested theoretically and experimentally, using a 5-cm-diam dielectric separator. High-dielectric mineral recovery was proportional to the calculated effective dielectric force volume (EDFV) that surrounded each drum-electrode wire. Electrode spacing was the most sensitive design parameter; spacing of less than 0.4 cm was required for a good separation. Dielectric separation was effective for separating minerals with dielectric constants that differed by approximately 2 or more.

Jan 1, 1985

By Gernot Schenker

With the shut-down in the mid-1970s of the last shaft furnaces in the Harz Smelter Plant the long tradition of the Primary Lead Smelter in Oker came to an end. A continuation of the concern was nevertheless possible as a result of the timely commencement with the development and construction of lead production from secondary raw materials. Then as today, the most essential secondary raw material is lead accumulator scrap with over 80 % of the raw material pallet. Already in the 1960?s a method of reclamation lead battery scrap was developed and successfully carr.ied out by Preussag. In 1983 this process was fundamentally modified, also for environmental protection reasons within the framework of a rehabilitation programme of the existing plant. Today Metaleurop's HarzMetall GmbH in Oker is equipped with a modern secondary lead smelter which includes all environmental protection installations required by law. Besides processing battery scrap, the. smelter is in a position to process a ?multitude of other lead bearing residues in an economically useful way, whose waste disposal would otherwise be impossible due to the ever-increasing environmental protection laws or only be achieved at great expense.

Jan 1, 1990

By D. A. Paice

Under the first phase of this contract as reported in the Phase I report it was determined that certain types of commercially available molded case breakers are capable of interrupting mine dc power supplies of nominally 300 volts or 600 volts rating. These circuit breakers incorporate conventional overcurrent trip units but also can be operated by means of low power signals fed to a shunt trip coil. Further development in the Phase I program produced a means whereby a discriminating circuit breaker detector unit could sense the presence of illegitimate loads on the dc electrical system and cause the circuit breaker to trip. The detector unit operated by detecting the presence of 3000 Hz currents which were generated in the illegitimate loads by means of a 12 volt, 3000 Hz signal applied to the dc system. Further development of the program has continued in Phase II with the aim of verifying the practicability of the complete discriminating circuit breaker concept and developing other types of equipments required to implement a system. These other equipments include electronic means for raising the apparent impedance of high power legitimate loads and static filters for smaller loads. The results of laboratory work and limited underground tests have been successful. This report describes the system and the tests that have been conducted on the various equipments that comprise the complete Discriminating Circuit Breaker Concept.

Jan 1, 2012

By Gary R. Gavan

This report presents the results of a research project that gathered detailed information on the composition of the population of mobile equipment used in U.S. coal mines. A computerized data bank containing over 19,000 pieces of coal mine equipment in use in 1976 was prepared with a data retrieval program. Operator protective structure technology is reviewed; field problems experienced with ROPS are discussed.

Jan 1, 1978

Approximately half of all the fuel energy used in the United states is now pro-vided by oil and natural gas. A persistent and rapid growth in energy demand during the last 3 decades has been absorbed largely by the liquid and gaseous rather than solid fuels. In 1948 the energy provided by coal was substantially the same as in 1920. Meanwhile, the use of oil and natural gas each had increased fivefold. On a per capita basis, the change is more significant. Coal consumption has dropped from about 6 tons per person to 4-1/2 tons, while oil has increased from 4-1/3 barrels to 14-1/3, and natural gas from 7,500 cubic feet to about 35,000. These facts would have only academic interest if the United States had unlimited supplies of all fuels. However, while the Nation's reserves of coal are adequate to meet our needs for centuries, those of oil and natural gas appear limited. It is obvious, therefore, that the security of our liquid-fuel position would be greatly enhanced if the supply could be based in an increasing degree on solid fuels, such as coal and oil shale, which make up more than 95 percent of our fuel reserves, instead of natural oil and gas. In addition, this would create new employment and help to stabilize the market for coal, which may be facing comparatively bleak prospects in the near future unless its position with respect to other fuels is improved.

Jan 1, 1950

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes? are considered one of the most promising alternatives to well-established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic-containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment-technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (000). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

Jan 1, 1897

By Kim Wiwchar, Elizabeth Mbaja, Lynne Dang, Jim Furey, Anita Marks

"Suncor Energy Inc., located north of Fort McMurray, Alberta, commenced pilot scale operation using a CPT 4’ diameter flotation column in March 2003. This larger scale trial follows two previously successful flotation column bench scale tests. They included an April 2002 trial with a 2.4” inner diameter column from the University of Alberta and a 20” diameter CPT column in August 2002. The column receives middlings stream feed from one of Suncor’s deep cone separation cells and is operated in parallel with a set of WEMCO flotation cells. The recovery, tails losses, and concentrate quality are being compared between the two systems. The column, to date, has been tested with all types of run of mine ore grades. Variables such as wash water flow and temperature, sparger nozzle size and location, sparger air/water flow rates, and column residence time has been adjusted to achieve better recovery and final product quality.Used in many mineral processing applications, column flotation is primarily used for the final stage of sulphide cleaning and flotation of phosphate or iron ore. As well, mechanical cells are often used in combination with a column to retrofit an operation and to produce a cleaner product.Initial results prove that this is the first successful application of a flotation column in an oilsand application. If viable, it will be an inexpensive process for recovery of bitumen from a middlings stream and able to produce a final product suitable for froth treatment.INTRODUCTIONSuncor’s oilsand is surface mined from the Athabasca Oilsand deposit north of Fort McMurray, Alberta. The oilsand is then mixed with hot process water (HPW) and the bitumen is slurried in a pipeline. Large separation cells as shown in Figure 1 float off the bitumen product, which is then steam or static deaerated and sent to Secondary Extraction for further cleaning. The tails stream from the cell is sent to the Final Tails Pumphouse (FTPH) for processing. The tailings flotation froth product gets recycled to the separation cell oilsand feed. The tailings are pumped from the FTPH to tailings ponds. The middlings stream is drawn off the separation cell approximately 9’ from the froth overflow level. It runs down, by gravity, to the scavenger banks for bitumen recovery. It was from this stream off of the Line 6 Separation Cell that the feed to the Canadian Process Technologies Inc (CPT) flotation column was taken."

Jan 1, 2004

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The course has been broadened in scope, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and non-metallic mines. These circulars are as follows: Injury Statistics (Miners' Circular 51), dealing with general statistics on injuries from accidents at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all injuries.

Jan 1, 1960

By C. M. F. Vieira

This work has as its objective to characterize ceramic bodies for vitrified tiles elaborated with the mixture of nepheline-syenite flux and kaolinitic clay. Formulations were prepared with 0, 30 and 50 wt.% of nepheline-syenite incorporated in a kaolinitic clay. To determine the physical and mechanical properties such as dry bulk density, linear shrinkage, water absorption and flexural rupture strength, specimens were prepared by 30 MPa uniaxial pressure-molding and then fired in a laboratory furnace at 1150oC. The microstructure of the fired ceramics was evaluated by scanning electron microscopy. The results indicated that the nepheline-syenite improved the evaluated properties of the clay and attended the specifications of vitrified ceramic tiles.

Jan 1, 2010

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By R. B. Toombs

In describing the Canadian mineral industry in a world setting, this paper examines the industry from four points of view. First, mineral industry growth is related to trends in economic activity thereby providing a measure of the industry's importance in the Canadian economy. To give perspective to the Canadian scene, reference is made to economic trends in several of the world's leading mineral producing and mineral consuming countries. The Canadian mineral industry is next examined in terms of its major developments of the past 20 years and the resultant size, structure, and production diversity of 1964. The position of the Canadian mineral industry in the world industry is then analyzed by tracing changes in mineral supply and demand patterns. Growth of the Canadian industry depends greatly on expansion of export markets because three fifths of the value of production is accounted for by exports. Finally, attention is directed to the outlook for the Canadian mineral industry. Problems facing the industry are surveyed, and an appraisal is made of economic policies that have encouraged industry growth. A forecast of mineral production value in 1970 is included.

Jan 1, 1964

By Marianne Snedeker

In September 1985 we published a questionnaire asking about the content of MINING ENGINEERING and about your interests. By Dec. 10, our cutoff date, we had 430 responses, representing about 1.5% of the 28,238 people who received the September issue of ME. In the data that follow the tabulation and percentages are based on the number of individuals who responded to the particular question. About ME Through responses to the questionnaire, we were hoping to learn more about you, your interests, and how the magazine could better serve you. Those of you who responded told us something positive - you look at or read the magazine. Of the 430 respondents, 428 or 99.5% indicated that they had read or looked through the July and/or August issues. Those of you who refer to the magazine once are 207 or 48.5%. Those of you who refer to the magazine two or three times are 193 or 45.2%. Those of you who refer to the magazine four or more times are 27 or 6.3%. How much time do you spend reading the magazine? Of those responding to this question: 64 spent up to 1/2 hr 15.0% 224 spent up to 1 hr 52.6% 115 spent up to 1-2 hr 27.0% 23 spent more than 2 hr 5.4% In an informal survey among our staff, we determined that most people spend 1/2 to 1 hr reading magazines to which they subscribe at home. Does that match your experience? Many of you, 335 or 79%, clip your magazine for further reference. Also, many of you, 313 or 73.6%, do not pass your copy on to another reader, indicating that you are clipping it or receiving the magazine at home. Those magazines that are passed on reach: 1 person 3 0.7% 2 people 64 15.1% 3-5 people 34 8.0% 5 or more 11 2.6% Answers to what portions of the magazine you find useful indicated that the top three were Industry Newswatch, feature articles and Technical Papers; see Table 1. The "other" category included advertising - display, classified, Employment, and Professional Services - Washington Survey, New Products, Free Literature, book reviews, technology news, and Coming Events and Short Courses. We asked your appraisal of the technical level of the magazine. Of those responding, 39 or 9.1% indicated that it is too technical, 55 or 12.8% indicated it is not technical enough, and 335 or 78.1% judged it to have the correct technical level. In response to the question about whether you like to read an occasional feature that is not technically oriented, 21 or 5.1% said no, but an overwhelming 94.9% (393) said yes. Of the specific

Jan 1, 1986

By Klaus-Peter Kinzel

Staves Coolers de cobre proporcionaram uma excelente proteção da carcaça do alto-forno em áreas de alta temperatura. Isso resultou para que os operadores de alto-forno alcançassem alto desempenho em termos de produtividade e taxa de combustível, além de campanhas de mais de 15 anos. No entanto, nos últimos anos, alguns altos-fornos experimentaram um desgaste prematuro nos staves de cobre. Algumas dessas empresas se alinharam com Paul Wurth para investigar a causa fundamental desse fenômeno com base em todos os fatores de influência e, em seguida, propor ações corretivas. Estes resultados são discutidos e apresentados a seguir no trabalho técnico.

Oct 30, 2017

By CLAYTON C. BALL

In the year 1948, more than ever before, the coal industry established itself on the threshold of a new and exciting future expansion. While production did not equal the wartime and peacetime peaks of 1944 and 1947, it was, in review, a good coal year. During the latter part of the year a combination of mild weather, record stock piling, and general business slackening reduced coal demand to the extent that marginal mines suspended operations, while mines remaining active found it necessary to renew their attention to producing better products at lower operating costs.

Jan 1, 1949

By E. Watkins, J. C. LeRoy, A. Vivyurka

"TAILINGS REVEGETATIONWelcome to the Revegetation Session. My instructions are to introduce the Speakers and to provide a general introduction.I do the latter with humility not only because of a lack of personal experience or because tailings revegation is not well established technology, but because any general statement on a country or industry as diverse as the Canadian Mining Industry is bound to be wrong somewhere.Laying aside normal standards of accuracy I proceed as follows:In considering the question of tailings revegetation, one asks two basic questions:1. What ought to be done?2. What can be done?The first question can be broken down into three kinds of criteria or objectives:a) Legislativeb) Technicalc) AestheticThe first I leave to the politicians and the last I will avoid. Aesthetics is the philosphy of taste. It is concerned with the appreciation of things rather than what they really are. It is much easier to get into an argument on aesthetics than to get out of it feeling you have said something of consequence.Technical criteria can be divided into the following sub-objectives: 1. To isolate the tailings basin so surrounding land is not degraded. The first step here is stabilization of the surface to prevent wind and water erosion."

Jan 1, 1975