Search Documents

By R. J. Campbell

[The steady increase of aluminum production means a corresponding increase of carbon consumption in the alumina-reduction cells. Improved petroleum techniques constantly reduce the amount of byproduct petroleum-coke production. These, trends threaten the alumina-reduction works with possible shortages of carbon, which must be supplied from some other source. In anticipation of this shortages, an investigation into the possibility of using coal as an alternative source of carbon was begun at the Northwest Experiment Station of the Federal Bureau of Mines. The investigation lit has developed bench-scale methods that produce carbon of higher purity than is required by specifications for anode carbon. Additional work will b required to bring these processes to pilot-plant seals and to prove the suitability of the carbons, produced or aluminum-anode consumption.]

Jan 1, 1956

By Frederick Laist

AFTER a series of experiments covering a period of about three years, ending from the spring of 19iJ.2 to the spring of 1915, a 2,000-ton leaching plant for the treatment of the accumulated copper concentrator tailing was built and put into operation. During the experimental period, the first step was that of laboratory experiments or beaker leaches. The results on this small scale were so satisfactory that a small operating plant, capable of handling 5 tons of roasted tailing per day, was installed. Again, the results proved satisfactory and an 80­ton plant was built and operated continuously from August until February, 1913. In this plant, full-sized roasting and leaching units were

Jan 8, 1916

By C. R. Summers

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneumatic drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115-dbA stope drill to approximately 100 dbA.

Jan 1, 1974

By F. K. McKean

Introduction The present paper may be considered as a sequel to a paper, A Process for Cleaning Molybdenite .Concentrate, which was presented by the author at the annual meeting of the Institute last year. In that paper, a description was given of the laboratory work leading up to the adoption of a new process for treating complex molybdenite ores of the Molybdenite Corporation of Canada. A bare outline of mill performance with the new flow-sheet was included. With this writing, the purpose is to describe the highly interesting work of translating laboratory experience into mill practice, to show what changes were required in design to put the scheme on an operational basis, and to point out the gratifying improvements in mill products which resulted from the new procedure. The process has been placed in operation at the La Corne mine of the Molybdenite Corporation of Canada. This mine was operated during the war by Wartime Metals Corporation, and, earlier, by the Molybdenite Reduction Company, which installed a small plant. The property is situated on the highway from Amos to Val d'Or, Quebec. The claims held by the Company are at the boundary between La Corne and Vassan townships.

Jan 1, 1947

By Dale S. Preece, Stephen H. Chung

Explosives energy can be used effectively in breaking and displacing large volumes of rock in mining and quarrying industries in both open pit and underground. The blast result, however, may not be economical if the applied explosives energy distribution is not properly applied to match a given set of geometries. However, this engineering problem can be resolved by using a modeling approach in the blast design process. Starting with a given set of blast design parameters that include explosive, elastic properties of rock, geometry of the blast pattern as well as the delay firing time, this paper shows how a discrete element blast model can be set up to allow the examination of the effect of critical design input parameters on blast results. Examples are given in this paper to help visualize the value and application of blast simulations. They are (1) regular and terrace bench blasting models for throw control, (2) underground blasting including a drop raise opening and (3) collapsing of a multiple room-pillar structure with proper firing sequence to control the mixing of blasted materials.

Jan 1, 2005

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By Jasinder S. Jaspal

In underground room-and-pillar mining methods, the sectional conveyor belts are extended or retracted periodically to maintain shuttle car tramming distance to a minimum. A conventional conveyor belt extension or retraction is a heavy, arduous job that if mecahnized, has the potential to improve productivity and safety. To reduce the burden of heavy work of this activity and mechanize it, the Bureau of Mines developed a conveyor belt service machine (CBSM) through a research contract with Tractor MBA. The CBSM is a self-contained, battery-powered, rubber-tired vehicle capable of handling, storing and transporting conveyor belting, wire rope, and associated belt structures in seams as low as 48 in. Belt extensions and retractions are accomplished by moving the tailpiece of a belt conveyor with the CBSM to the next position while dispensing or retrieving the belt, wire rope, and associated belt structures. The CBSM improves the belt extensions and retractions by making them easier and faster, and it utilizes fewer workers. The CBSM was surface tested at the Bureau's Mining Equipment Test Facility (METF) to evaluate its performance and reliability. Modifications were made to the CBSM to correct deficiencies found during surface testing.

Jan 1, 1988

"NI 43-101 is a rule that governs how issuers disclose scientific and technical information about mineral projects to the public in Canada. The disclosure standards apply to oral statements as well as written documents and websites. NI 43-101 does not apply to disclosure concerning petroleum, natural gas, bituminous sands or shales, groundwater, or coal be methane. NI 43-101 first came into force on Feb. 1, 2001 and was revised in December 30, 2005. As a “National Instrument”, the law has been passed in each provincial and territorial legislature across Canada.“PART 1 DEFINITIONS AND INTERPRETATION 1.1 Definitions - In this Instrument “adjacent property” means a property(a) in which the issuer does not have an interest;(b) that has a boundary reasonablyproximate to the propertybeing reported on; and (c) that has geological characteristics similar to those of the property being reported on; “data verification” means the process of confirming that data has been generated withproper procedures, has been accurately transcribed from the original source and is suitable to be used; “development property” means a property that is being prepared for mineral production and for which economic viability has been demonstrated by a feasibility study; “disclosure” means any oralstatement orwritten disclosure made by oron behalf of an issuer and intended to be, orreasonablylikely to be, made available to the public in a jurisdiction of Canada, whether or not filed under securitieslegislation, but does not include written disclosure that is made available to the public only by reason of having been filed with a government or agencyof government pursuant to a requirement of lawother than securities legislation; “early stage exploration property” means a property that has(a) no current mineral resources or mineral reserves defined; and (b) no drilling or trenching proposed; in a technical report being filed in a local jurisdiction; “exploration information” means geological, geophysical, geochemical, sampling, drilling, trenching, analytical testing,assaying, mineralogical, metallurgical and other similar information concerning a particular property that is derived fromactivities undertaken to locate, investigate, define or delineate a mineral prospect or mineral deposit; “feasibility study” means a comprehensive studyof a mineral deposit in which all geological, engineering, legal,operating, economic, social, environmental and other relevant factors are considered in sufficient detail that it could reasonably serve as the basis for a final decision by a financial institution to finance the development of the deposit for mineral production; “historical estimate” means an estimate of mineral resources or mineral reserves prepared prior to February 1, 2001;“IMMM Reporting Code” means the classification system and definitions of mineral resources and mineral reservesapproved by The Institution of Materials, Minerals, and Mining in the United Kingdom, as amended; “JORC Code”means the Australasian Code for Reporting of Mineral Resources and Ore Reserves prepared by the Joint Ore Reserves Committee of the Australasian Institute of Mining and Metallurgy, Australian Institute ofGeoscientists and Mineral Council of Australia, as amended; “mineral project” means any exploration, development or production activity, including a royalty interest or similarinterest in these activities, in respect of diamonds, natural solid inorganic material, or natural solid fossilized organic material including base and precious metals, coal, and industrial minerals;"

Jan 1, 2003

By G. L. Oldright

In the first paper of this series (R. 1. 4333) on the cooperative work with the Eagle-Pitcher Mining & Smelting Co., changes in the nature of the sinter feed were measured by corresponding changes in the retorting temperatures necessary to distill zinc at the best rates; the firing schedules summarized such changes. In this paper, third of the series, are noted same of the changes in practice that were brought about by the need to treat more fused, glassy, and "hard" sinter, as the operators qualify it. Losses of uncondensed zinc were increased by adding zinc-bearing materials from which? the zinc was readily distillable to hard sinter requiring higher-temperatures for zinc distillation. The rates of zinc distillation were increased by grinding the fuel finer; there were few benefits and loss of dust on grinding the sinter finer, unless the fine ?coal and fine sinter were brought into contact by pelletizing, and the pellets made but little dust.

Jan 1, 1948

By Mark K. Larson

Researchers at the U.S. Bureau of Mines have developed a FORTRAN computer program that can calculate stress states from overcoring measurements obtained from hollow inclusion cells, triaxial cells, strain gauges installed on the wall of a bored raise, doorstopper gauges, borehole deformation gauges, or a combination of any of these gauges. Such stress states are calculated with reference to global and principal coordinate systems. The background of the development of the program, its capabilities, and its special features, as well as the input required, are described in this report. Sample output is also shown in appendix C. Difficulties associated with numerical calculations of principal stresses and directions are pointed out. Threshold values for detecting these problems are reported; these values may be changed by the user as desired. Several test problems were set up to verify the computer program and were successfully solved.

Jan 1, 1992

By A. H. Cronk

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods and costs in the different mining districts. The mining methods described in this paper are employed by one of the large mines in the Illinois fluorspar district. The mine is located at Rosiclare, Ill., and shipments are made over the Illinois Central Railroad: and by barge on the Ohio River.

Jan 1, 1930

A description is given of the construction and operation of an automatic version of the coarse batch particle sizer which requires a minimum of operator supervision and which is capable of processing a sample every 4 min.

Jan 1, 1968

By AIME

Burton J. Westman-Besides decreasing the diamond size, there appear to be two other approaches open to overcome excessive diamond loss and, more particularly, the rapid diamond polish that took place in this quartz-feldspar rock. First, however, a short discussion of the diamond characteristics should be made in order to discuss the situation more clearly. The West African diamonds which we can assume were used. for this drilling have two disadvantages when drilling hard, exceptionally fine-grained rocks. These are rapid polishing and, if .the bit isn't "drilled in" carefully, a tendency to damage, resulting in excessive diamond loss. The normal wear resistance of any diamond is inversely proportional to the compressive strength of the diamond, therefore only the highest grade, of diamonds free from insipient fractures should be employed. Using upwards of 90 diamonds per carat instead of the20 to 30 per carat not only decreases the total projected area of the cutting points but increases the stress per point which, in turn, causes greater depth of penetration into the rock. Considering this depth of penetration, therefore, suggests an approach other than increasing the, number of diamonds per carat and that is to decrease the actual number of diamond points (also the carat weight per bit) so that the penetrating force on an individual diamond is increased. This penetration increases the chipping or rock shearing action.

Jan 1, 1950

By C. Rutledge

The new mining method of multiple strata blasting, called StratablastTM, is described in a separate paper presented at this conference. The current paper presents three case studies where the technique was implemented in three different configurations in large-scale blasts in Australia. The first two blasts were in the Hunter Valley of NSW while the third was at Ensham Mine in Central Queensland. All blasts comprised multiple layers that were blasted in a single drill and blast cycle, with unique designs applied to each layer to achieve different blast outcomes from the various layers.

Jan 1, 2006

By Juan Mendoza Marsano

"El presente texto revela las primeras transacciones de la venta del oro en el Perú -en tanto se determina su precio a través de un acuerdo denominado""on the spot"", donde el vendedor ofrece sus mercaderías a uncomprador y se acuerda un precio pagado con dinero al contado y de inmediato. Hasta 1914 el precio del oro estuvo determinado o fijado por la denominación de las propias monedas circulantes de oro y sus monedas equi- valentes. Sin embargo, la primera determinación del oro en el Perú surge en Cajamarca, 1553. Posteriormente se describe la circulación de este durante la Colonia, los diferentes métodos de transacción y las especificaciones del contratos de oro, así como los factores que influyen en el precio del oro."

Nov 1, 1978

By Charles E. Whieldon

Data on the oilfields in Mahoning, Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and compiled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965

By Victor R. Eyzaguirre

Cerro Verde is one of several large porphyry-type copper deposits in Southern Peru. The copper occurs as primary sulphides, with a significant oxide capping. The exploitation of the deposit has been correspondingly divided into two stages, the first consisting of copper production from oxides, and the second from sulphides. Minero Peru successfully started the Stage I plant in June of 1977 with the first production of electrowon copper cathodes. This paper is essentially devoted to a description of the Stage I process, which can be summarized as follows: Ore is trucked to the primary crusher, where it is crushed to 225 mm and conveyed to a coarse ore stockpile. Ore withdrawn from the stockpile is secondary crushed to 65 mm, conveyed to a truck loadout bin, loaded into trucks and driven to the leaching pads. Ore is placed on the pads in lifts and sprayed with sulphuric acid solution to dissolve the copper. Copper-bearing solution forms a pond behind a dam at the lower end of each pad and is pumped from there to the solvent extraction plant. Copper is extracted from the leach solution into an organic phase and is then stripped from the organic phase to form a purified concentrated copper solution suitable for feed to electrowinning. In electrowinning, the copper is finally recovered as cathodes suitable for sale as refined copper.

Jan 1, 1978

By Isobel Yeo, Luca Cocchi, Sven Petersen, Nico Augustin, Sean Plunkett, Ingo Klaucke

Exploration for seafloor massive sulfides is currently mainly focused on investigation for active hydrothermal vent fields. However, most of the resource potential is thought to be related to inactive, large deposits that had enough time to accumulate sufficient tonnage. At the same time, ageing of these deposits will ultimately result also in burial acted by either sediments and/or volcanic deposits. We currently lack the technologies to explore for these deposits in a time- and cost-efficient manner. In the fall of 2012 we used a number of AUV-based technologies to explore and image a sulfide occurrence at the Palinuro Volcanic Complex in the Tyrrhenian Sea (Mediterranean Sea; Fig. 1) where sampling and drilling have documented a buried polymetallic barite-pyrite dominated site (Petersen et al., 2014). Sulfide mineralization is here covered by volcaniclastic and pelagic sediments and only red sediment staining and the presence of few tubeworm bushes indicated recent hydrothermal activity - black smoker venting is absent. We used AUVbased high-resolution bathymetry, sidescan sonar imaging, subbottom profiling, as well as magnetics to describe, in a quantitative way, the previously known sulfide-bearing areas as well as to successfully explore for new hydrothermal sites including large chimney structures (Figs. 2). Additionally chemical sensors (CTD, Eh, turbidity) investigated the water column for signs of hydrothermal activity in areas not previously investigated, but at the end, only weak anomalies were found in the southern part of the summit.

Sep 1, 2014

By Robert F. Chaiken

The Bureau of Mines is using model ducts lined with coal to study the nature of coal mine fires, their rate of propagation, their influence on ventilation airflows, and their response to sealing and other fire suppression measures. For scale-modeling purposes these studies are being carried out in various size ducts; eventually they will include a full-size mine entry in the Bruceton multiple-entry Experimental Mine. To date, work has been carried out in an insulated 9.l-m-long duct with a 5-cm thickness of coal leaving a 23-by 23-cm square opening for air ventilation. Fire propagation processes in this duct were mainly transient in nature owing to the relatively small length-to-diameter ratio. This report describes the experimental equipment employed and the results obtained to date.

Jan 1, 1979

By James A. Finch, Jason S. Doucet, Cesar O. Gomez

"Exercising control over the physical environment of flotation as a step towards process optimization is the driving force for characterizing gas dispersion in flotation cells, a subject of considerable research and still not fully understood. From an operational standpoint, however, there are just a few variables that can be manipulated to manage gas dispersion on a cell-to-cell basis, the most important being gas rate (superficial gas velocity Jg). Measurements in eight plants demonstrate there is often no strategy for distribution of gas to cells in a bank, i.e., there is no particular Jg profile. Two exercises where Jg profiles were set allowed metallurgical performance to be manipulated and an optimum Jg profile to be selected. To facilitate setting Jg profiles, a multi-unit device based on McGill Jg sensor technology is introduced. Possible directions for gas dispersion management are discussed.INTRODUCTIONThe earliest patents regarding the flotation process ignored the importance of air and in certain cases, steps were taken to eliminate bubbles from the system (Nelson and Smit, 2005). Rickard (1916) described a keen metallurgist who observed better than expected performance and hypothesized that entrained air was enhancing the process. Within a few years of this observation, the basic concept of modern froth flotation was developed whereby air is dispersed into slurry to induce bubble particle contact.As research into flotation advanced, the link between performance and the flow-rate of air entering the cell was established. In the first volume of the International Journal of Mineral Processing, Harris (1974) described the importance of airflow-rate and derived parameters such as the superficial gas velocity (then called the superficial airflow velocity) as being important parameters for cell design and scale-up. Mehrotra and Kapur (1974) presented research suggesting that the rate of flotation was strongly correlated to the aeration rate. McKee et al. (1976) continued to demonstrate the importance of airflow-rate linking it to the entrainment rate of hydrophilic gangue material."

Jan 1, 2006