Search Documents

By Charbel Khoury, Kwabena Ofori-Awuah, Kofi B. Acheampong

"Following heavy rains in spring of 2014, Prince George’s County officials issued a mandatory evacuation for homes in the Piscataway Hills subdivision of Fort Washington, Maryland where a landslide along a 1700-foot hillside destabilized homes, collapsed the single access road, and resulted in water and sewer mains break. Forensic investigations, including geologic assessments, test borings and in-situ Cone Penetrometer and Dilatometer soundings, were performed to evaluate subsurface conditions and provide stabilization options for the roadway and slopes. Post-failure ground movements were monitored using inclinometers. Critical failure planes were identified within the underlying 30-foot thick Marlboro Clay formation, a known geologic hazard with historic occurrences of landslides and slope failures.This paper discusses the remedial design for stabilizing the landslide and 60-foot hillside slope failure, and protecting the roadway. Amongst several feasible options, driven piles were selected in consultation with the County and retained contractor based on cost, environmental impacts and site constraints. Constraints included private ownership of hillside slope, upslope buildings safety; deep-seated failure, relocation of underground water and sewer mains, and accelerated construction schedule.Pile design included global slope stability analyses and lateral pile analyses using several loading configurations to optimize pile geometry and spacing, and determine a value-engineered design satisfying both serviceability and strength limit states to achieve long-term stability with factor of safety of 1.3. Soils within the active landslide plane were assumed to provide no resistance, while soils below the failure plane provided lateral resistance. This stabilization scheme, which extended along the 1700-foot roadway section and toe of hillside slope area, consisted of 410 steel HP16x141 piles in two to three rows driven to depths between 60 and 70 feet below the Marlboro Clay stratum at 5 to 7-foot spacing."

Jan 1, 2017

By N. A. Jabit

The dissolution behaviour of ilmenite in acid solutions has been studied by many researchers to improve the leaching efficiency. Most studies which utilized natural ilmenite from different origins resulted in different reactivity due to the alteration caused by the weathering process. Previous researchers have suggested that the greater reactivity shown by some ilmenite samples towards sulphuric acid may be a result of the mineral being relatively unaltered. In the present study a rotating synthetic ilmenite disc of 2.2 cm diameter was subjected to leaching studies in hydrochloric acid. The dissolution rates of iron and titanium from synthetic ilmenite were determined in hydrochloric acid solutions (4 M to 9 M) over a temperature range of 50 to 80°C. Results show that the rate of dissolution of both iron and titanium increased with the increase in acid concentration. However, the rates decreased with time and obeyed a parabolic rate law indicating the blockage of the surface by an insoluble product. The rates of dissolution of both iron and titanium were higher in the presence of SnCl2 and remained unaffected with time indicating the reductive role of SnCl2 which inhibits the formation of surface blocking solids. Application to natural ilmenite is also discussed.

Jan 1, 2014

The purpose of this paper is to describe briefly the clean-up procedure adopted at the treatment plant of Paringa Mining & Exploration Co. Ltd. at Kalgoorlie, Western Australia.A clean-up is carried out at the end of each four-weekly period, and all figures subsequently quoted are taken from a summary of the results of the eight periods ending 8th April, 1941.STRAKING AND AMALGAMATIONOf the total gold won 22· 77 per cent. is recovered by straking and amalgamation.The discharges of both the primary and secondary ball mills are pumped over a common set of five ten feet long by three feet wide straking tables, set at an angle of 10 degrees, before passing to the 14 ft. diameter by 30 ft. by 8 ft. Dorr bowl classifier.This classifier is in closed circuit with both of the ball mills, hence the whole of the circulating load of the fine grinding circuit, which approximates to 800 per cent., is required to pass over the straking tables. For convenience in handling, corduroy cloths are used in lengths of 5 feet, and are picked up and replaced by clean cloths at four-hourly intervals. The avaHable straking area provided is, therefore, 900 square feet, or approximately 3·30 square feet per original ton per 24 hours. The density of the pulp passing over the tables is about 54 per cent. solids, the area provided per ton of pulp per 24 hours being approximately o· 2() square feet. Washing of the corduroy cloths is carried out on the day shift only, about 800 lb. of strake concentrate being obtained daily.This concentrate is sluiced from the washing trough on the elevated straking floor to the 4 ft. by 2 ft. diameter amalgamating barrel located in the gold room below.The barrel is of standard design and is rotated at 25 r.p.m. It is charged each day at 4 p.m., and grinding of the strake concentrate at approximately 70 per cent. solids is continued until 8 a.m. the following day. The barrel is then stopped, and the contents generously diluted with water, and after a few minutes rotation some of the slime is carefully poured off through the small discharge hole. This dilution and decantation is repeated until a good deal of the valueless slime has been removed.A further quantity of strake concentrate is then charged to the barrel, which is allowed a further 16 hours grinding period. After again diluting and decanting, approximately 25 lb. of mercury and 15 lb. of lime are added to the charge, which is then given an amalgamation period of 2 hours before cleaning up.By the process of grinding, diluting and removal of slime by decanting...

Jan 1, 1941

By R. Romano, E. Montalar, J. B. Serón

The SMR geomechanics classification system (adaptation of RMR for slopes) is reviewed with data from 87 actual slopes in Valencia. In a research project, SMR has been applied by a GIS system, as a method to forecast stability problems in future road construction. As a result of this work a methodology for GIS application has been developed. On revient sur la classification geomechanique SMR ( une adaptation du RMR pour talus et pentes) avec les dates de 87 talus existant autour de Valencia. Dans le cadre d’un projet de recherche SMR a été appliquée, avec un système GIS, comme méthode de prévision de stabilité problèmes dans la construction de futures routes. Une méthodologie pour l’application du GIS a été développe. Das Geomechanische Einteilungssystem SMR (eine Anpassung des RMR an Böschungen) wird an Hand der Daten von 87 Böschungen im Gebiet von Valencia überdacht. In einem Forschungsprojekt wurde das SMR in einem Geographischen Informationssystem (GIS) als Methode zur Vorhersage von Stabilitätsproblemen bei zukünftigen Straßenbauprojekten eingesetzt. Das Ergebnis dieser Arbeit ist die Entwicklung einer Methodologie für die GIS-Anwendung

Jan 1, 2003

By Baker G

The exposures resulting from development work, following on the discovery of a new shoot of hIgh grade ore at the north end of the Sardine tin mine, during 1952, have provided an unusual opportunity to study the oxidation of a stannite-rich ore. Through the kindness of C. C. Morton, Chief Government Geologist of Queensland, an exactly located suite of specimens representative of the exposures was supplied by J. and W. Reddie. This was later supplemented by a number of specimens culled from a parcel ofrepresentative ore submitted to the Melbourne Ore Dressing Laboratory for testing.The Sardine tin mine, near Ewan, Queensland, has been the outstanding producer of the Kangaroo Hills Mineral Field. Since its discovery in 1918, up to 1952 it has yielded about 1,500 tons of cassiterite concentrates, and about 85 tons of stannite concentrates. The outcrop ore averaged 35% tin oxide, but the grade declined with increasing depth, and by 1930 had fallen to 7% tin oxide. In the northern section of the mine the ore shoots show a downward passage to complex primary s.ulphide ore, containing cassiterite and abundant stannite.The orebodies occur in a series of fissures in a crushed zone about 50 ft. wide in slates and quartzites that have been intruded by granite (Connah, 1952). A quartz porphyry dyke forms the footwall of the original main lode in its southern part, being traced' from the surface to' the No. 4 level (173 ft. vertical depth), and two narrow dolerite dykes were encountered in the workings north of the main...

Jan 1, 1954

By S. Al-Hassan

The deposit has been exploited for Mn oxide and carbonate since 1916. Known reserves of MnO, however, are almost depleted and the survival of the mine will depend on the exploitation of the carbonate. Kriging, inverse distance weighting (IDW) and cross-sectional methods have been applied to the evaluation of the carbonate resources and reconciliation of the estimates obtained shows that kriging and IDW give almost identical block values. A comparison using conditional probability indicates that there is virtually no difference between the global reserve estimates derived from the cross-sectional and kriging methods. The physical causes of these similarities are highlighted and the problems of dealing with multimodal distributions are discussed together with the difficulties of semi-variogram modelling

Jun 19, 1905

By Paul D. Tomlingson

During the next several months, SME’s E-Newsletter will feature 15 articles on maintenance management. The articles may be read online or downloaded and distributed within your organization. They will address maintenance management topics, offer guidelines to mining managers and provide techniques that the maintenance manager can use. The articles will stress equipment management, a strategy that the mining industry has accepted as a modern replacement for outdated maintenance practices. Equipment management is the mutually supportive interaction of all mine departments as they establish equipment needs, procure equipment, test, commission, operate, maintain, modify and eventually replace equipment. The successful application of equipment management principles can quickly and reliably produce cost reduction and performance improvement results while providing a dependable way of sustaining them. Equipment management embraces modern management techniques. These include reliability-centered maintenance, life-cycle costing, capital performance, the effective use of information and productive organizational models.

Jan 1, 2003

By Paul Hewitt, Tim Smirnoff

Design and construction of the Epping to Chatswood Rail Line tunnels in Sydney, Australia required an innovative approach to define hydrogeological properties of the Sydney Hawkesbury Sandstone and provided an insight into the hydraulic behaviour of fractured sedimentary rocks. To meet restrictive water inflow and infiltration criteria both the pre-treatment of zones of fractured or highly jointed rock, and waterproofing using an interior spray on membrane for the finished drained tunnels and stations was required. Methods typically used to address the interaction of groundwater and tunnels in the Sydney Basin are demonstrated by case histories from major design-build tunnel projects.

Jan 1, 2005

By Y. Zhoa

The surface morphology of materials is of fundamental importance to many surface related applications, such as wetting, friction, reflection, drag, and adhesion. Various approaches for micro/nano patterning atop polymer surfaces have been proposed in recent years. However, a cost effective technique is still highly in demand. In this paper, we demonstrate a novel but rather simple and generic approach for surface micro/nano patterning using shape memory polymers (SMPs). Different types of novel patterns are realized and their 3-D surface features are quantitatively analyzed by a PLµ Confocal imaging profiler.

Jan 1, 2010

By R. W. Watson

A belt-wearable self-contained self-rescuer (SCSR) manufactured by the CSE Corp. and designated the "SR-1OO" was evaluated for safety in the underground mine environment by the U.S. Bureau of Mines. The evaluation consisted of laboratory tests on the chemicals contained in the unit and field trials to simulate the mine environment. This report summarizes the test results and compares the results with those from earlier tests with chemical and compressed oxygen self-rescuers. It was concluded that the new SCSR did not pose any different or more severe hazards than the earlier units. In view of the mine-proven safety record of the SCSR's now in service, no reason could be found to disallow use of the belt-wearable unit.

Jan 1, 1991

By F. T. Cawood

This article is a continuation of a series of publications by the authors on the international debate on resource nationalism, with specific reference to South Africa. Previous outcomes have shown that mine nationalization is not a solution for South Africa, and that maintaining stability of the current mineral and tax regimes is fundamental. It will not be wise to replace existing law and policy instruments until there is a better understanding of the distinction between fact and public perception about the impact of the current system. The new scheme of state custodianship linked to a mining royalty that effectively targets economic rents provides for effective resource use. The methodology in this article is to consider how South Africa's mineral tax regime can be tweaked to achieve optimal management and benefit from mineral extraction and associated rents by avoiding changes feared by investors. The major finding is that the current suite of instruments can be considered a suitable platform for optimal management of resource rents. However, it will be necessary to first investigate ways of improving the mineral beneficiation intent of the royalty structure, and secondly investigate whether the mineral rent portion of the royalty formula can be ring-fenced for the purpose of establishing a sovereign wealth fund.

Jan 1, 2013

By H. O. McLeod, J. M. Campbell

Data analysis of pentane and hexane adsorption from natural gas in a fixed bed of silica gel shows that constant length mass transfer zones form, the curvature of the adsorption isotherm controls the growth of the mass transfer zone and surface diffusion of molecules inside the silica gel particle controls the mass transfer rate. Curvature of the hexane isothem is more than the curvature of the pentane isotherm. Because of this curvature the hexane adsorption zones reached a constant length. In contrast, the pentane adsorption zones were always increasing in length during each run. A procedure was developed to obtain correct mass transfer coefficients using effluent curve slopes. These transfer roefficients increase with the amount of hydrocarbon adsorbed on the silica gel particle. The characteristic shape of the hexane effluent curves also show that molecular diffusion inside the silica gel particle controls the adsorption rate of pentane and hexane. INTRODUCTION The purpose of this study was to determine the mechanisms that control the dynamic adsorption of hydrocarbons from a natural gas onto silica gel. Before one can deal effectively with multicomponent adsorption, the transfer mechanisms by which a single hydrocarbon component is adsorbed from the gas stream must be defined. Two principal investigations of this system have been published ' and indicate that diffusion through the gas around the particle controls the adsorption rate. Some of the experimental observations in each study either do not support this transfer mechanism or are inconsistent with the mathematical model used in analysis. In this study surface diffusion of molecules inside the particle controls the mass transfer rate of pentane and hexane. This mechanism is indicated by the effluent curve shape for a constant length transfer zone and by the variation of the mass transfer coefficient with concentration of the adsorbed hydrocarbon. THEORY AND DEFINITIONS — MATHEMATICAL MODELS Mathematical solutions for the isothermal adsorption of a trace component from a carrier gas are derived from three relationships: the mass balance or continuity equation, the equilibrium relationship between the gas and solid phases, and a mass transfer rate equation. The transfer rate is proportional to the adsorbate concentration gradient within either the gas or solid phase. Mathematical solutions of these equations usually give the adsorbate concentration as a function of time and distance from the bed inlet. That part of the bed in which the adsorbate concentration changes from a maximum to a minimum value is called the transfer zone. This transfer zone is directly related to a plot of the effluent concentration vs time which has a characteristic S-shape. This general shape is determined by the continuity equation and occurs in many processes of diffusional transfer.

Jan 1, 1967

By P. H. Mutschler

The Bureau of Mines studied the costs of transporting fossil fuels, coal, and residual fuel oil from areas of production to consumer regions. Transportation data were stratified by type of carrier, size of shipment, and distance to determine what general effects these variables have upon transportation costs. Economics of haul for coal exist for longer versus shorter distances, and for larger versus smaller trainload sizes. Tanker and barge transportation of residual fuel oil does not show economies of haul for longer distances. It is shown that tanker size and seasonal variation are primary factors influencing the cost of shipping. Railroad transportation data show that coal from western coalfields could be competitive with foreign residual fuel oil in selected midwestern fossil fuel markets. However, the western coal would not be competitive in the New England and the eastern seaboard energy markets.

Jan 1, 1973

By T. T. Chen

Copper anodes generated from copper scrap are relatively rich in Sn, Zn and Fe. Because of the presence of oxygen, only trace amounts of Sn occur in solid solution in the copper crystals. Thus, Sn occurs mainly as SnO2, Cu-Sn-Ni oxide and Sn-Ni-Zn oxide in the copper anodes, and Zn and Fe occur mainly as minor constituents in the Sn-Ni-Zn oxide and Cu-Sn-Ni oxide. During electrorefining, these oxide species are liberated from the copper anodes and report directly to the anode slimes. The trace amounts of Sn present in solid solution in the copper crystals dissolve but reprecipitate as Sn arsenate or a Sb-As-Sn-O phase. Accordingly, high Sn contents in copper anodes do not lead to elevated Sn concentrations in the electrolyte.

Jan 1, 2010

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By J. P. May

This U.S. Bureau of Mines report identifies and evaluates factors responsible for dump-point accidents involving mobile mining equipment. Information regarding the occurrence and severity of the accidents, the industries affected, the types of equipment involved, the primary and contributing causes, and pertinent Federal regulations is included. The aim of this report is to provide information that will aid mine operators in the recognition of hazards associated with mobile equipment operation near the dump points of stockpiles and waste dumps.

Jan 1, 1990

By William C. Cooley

This report includes a review of all relevant data on underground hydraulic coal mining technology collected during Phases I and II of the contract. Data collection and analysis procedures are discussed. Information is included on past and existing underground hydraulic coal nines in the USSR (27 mines), Poland (1 mina), Germany (1 mine), Japan (1 mine), Canada (1 mine), China (1 nine), as well as underground tests conducted in the United Kingdom (2 mines), and in the United States (5 mines). Data is also included on Czechoslovakia and New Zealand. In all operational hydraulic mines, coal is transported underground in flumes. In most cases, bituminous coal is broken by monitors with nozzle diameters larger than 16 mm (0.63 in.) and jet pressures of 50 to 125 atm (710 to 1780 psi). Technical design and performance data are included on all key types of equipment and components which have been developed for, used in, or which could be potentially be used in hydraulic coal mining systems. Data sheets are presented on 180 types of equipment, divided into 24 major categories. Where available, sketches, drawings, photographs, and price estimates are included. Data are included on pitching coal seams in the United States which potentially can be mined by hydraulic methods. Preliminary conclusions are presented, subject to revision as a result of economic feasibility studies to be completed during Phase III. An outline is presented of the final report, which will include economic studies and recommendations for research and development.

Jan 1, 1975

By Kenneth G. Skinner

The rapid growth of the metallurgical, chemical, and allied industries on the Pacific coast just prior to and during the war caused a sudden increase in the demand for refractories, which was the immediate cause of a revival in interest in refractory clays available on the Pacific coast, particularly in the Pacific Northwest. Population increases and shortage of shipping facilities caused an increase in the amount of various ceramic materials and products used and produced on the Pacific coast, with accompanying demand for information regarding sources of clay. In an effort to supply part of this information, the Bureau of Mines, in cooperation with the College of Mines, University of Washington, started a program in 1944 to test the refractory and other properties of clays from seven Pacific Northwest deposits that had been drilled and sampled as part of the Bureau of Mines alumina from clay investigation. Figure 1 shows the location of these deposits.

Jan 1, 1949

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

By R. H. Grau

Researchers from the National Institute for Occupational Safety and Health have demonstrated that mine-wide ventilation in large-opening stone mines can be improved by using low-pressure, high-volume propeller fans and constructing stoppings in key locations to direct and control airflow. In light of these findings, a comparative study was conducted to determine if a portable diesel-powered propeller fan could per-form more efficiently for dust dilution and transport than an axial vane fan for localized ventilation. The objective of this study is to evaluate both fan types for ventilation efficiency at an underground dump/crusher facility in a limestone mine. Results showed an improvement with the propeller fan to dilute both the respirable dust and the respirable silica dust around the dump/crusher facility. Overall, an average reduction of 20% in respirable dust and silica was observed at the dump/crusher location with the propeller fan.