Search Documents

By Emad Iskander

The seepage forces generated around pressurized water tunnels in rock are investigated using the analysis tools of geomechanics. The theoretical background of the two-phase material behavior is explained and the equations of motion and continuity are presented. Applications on two case studies typically occurring in practice deal with the required minimum rock cover for a pressurized tunnel and the separation between two tunnels carrying different heads. The rock mass behavior as described by the Mohr-Coulomb and Hoek-Brown material models is investigated by numerical analyses and the results are compared. The effect of key material parameters on the safety factors and the associated modes of failure is discussed.

Jan 1, 2008

By D. C. Yates, G. V. Jolliffe

In the five coalfields of Staffordshire, there have been some 43 incidents of spontaneous fires and heatings which have required special attention in the past ten years. This total excludes incidents in the Thick Coal Seam of South Staffordshire, which was worked until 1967, and which was subject to an almost continuous series of heatings. The incidents have been classified to show the sites of occurrence, the contributory factors which may have caused them and the treatments applied to them. The remedial techniques, as practised in Staffordshire, are dealt with in detail, with particular reference to standard methods of stopping-off. Precautionary measures taken are described, including a "liability to spontaneous combustion" classification of all seams, and the setting up of an emergency organization with emergency stocks of materials and equipment. The paper is concluded by a few words on the organization and control at the time of an incident.

May 23, 1905

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company's Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963

By T. N. Rushton

Rate minima are encountered in the reduction of magnetite with hydrogen. In a certain temperature zone, the reaction rate decreases with rise in temperature. This is inexplicable by classical kinetic theories; neither is a transition in reduction mechanism suitable for interpreting the observed behavior, This anomaly can be fully explained by hypothesizing two species of chemisorbed hydrogen with different adsorption coefficients and activation energies for adsorption. Competition between two energetic states of adsorption occurs with temperature rise, with the low energy state predominating below the anomalous temperature zone and the high energy state above it. The presence of two possible adsorption sites appears to be characteristic for oxidic adsorbents.

Jan 1, 1968

By A P. Brown

Access arrangements required with landowners and occupiers; relaxation on size of permits; lack of confidentiality for information provided; one-stop shop under RMA, removal of standing; plethora of controls; post-closure; funding for long-term security.

Jan 1, 1997

By Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular industry or commodity. 2. Recirculation is dependent on the processing requirements of a particular commodity, the manner in which the water is used, cooling and condensing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast

Jan 1, 1966

By R. J. Pine, J. M. Rance, J. S. Coggan

ABSTRACT: The safe design of excavations created in a fractured rock mass is of paramount importance in rock engineering. Depending on the nature of the stress regime acting on an excavation, and the associated deformational behaviour of the rock mass surrounding the excavation, a number of potential failure mechanisms exist. These involve a combination of shear failure on existing joints, extension of critically oriented joints and propagation of new fractures through previously intact rock. Conventional numerical codes usually adopt either a continuum or discontinuum approach; this often results in significant over simplification and kinematic limitations particularly when modelling complex rock mass behaviour in the close vicinity of excavations. This paper describes the results from several case examples using a combined finite element-discrete element code, ELFEN that incorporates a crack propagation mode. Through the use of selected rock engineering examples, the authors demonstrate the potential of the code in the realistic simulation of complex rock failure both in underground and surface excavation applications. RÉSUMÉ: La conception sûre des excavations créées dans une masse de roche fracturée est d'importance primordiale dans la géotechnique. Selon la nature du régime d'effort autour d’une excavation, et le déformation associé de la masse de roche autour de l'excavation, il exsite un certain nombre de mécanismes potentiels d'échec. Ceux-ci comportent une combinaison d'échec de cisaillement sur les joints existants, la prolongation des joints d’orientation critique et la propagation de nouvelles ruptures dans la roche précédemment intacte. Les codes numériques conventionnels adoptent habituellement l’approche, soit d’un continuum, soit de discontinuum; ceci a souvent comme conséquence une sursimplification significative et les limitations cinématiques en particulier en modelant le comportement complexe de la masse de roche très proche des excavations. Cet article décrit les résultats de plusieurs exemples de cas en utilisant un code qui s’agit d’une combination d’élément discret et d'élément fini, ELFEN qui incorpore un mode de propagation de fissure. Par l'utilisation des exemples choisis géotechniques, les auteurs démontrent le potentiel du code dans la simulation réaliste de l'échec complexe de roche pour les applications aux excavations soit au fond soit à l’extérieure. ZUSAMMENFASSUNG: Das sichere Design der Aushöhlungen, die in einer zerbrochenen Felsenmasse verursacht werden, ist vom paramount Wert in der Felsentechnik. Abhängig von der Natur des Druckregimes, das auf einer Aushöhlung und dem dazugehörigen deformationalen Verhalten der Felsenmasse umgibt die Aushöhlung fungiert, bestehen eine Anzahl von möglichen Ausfalleinheiten. Diese beziehen eine Kombination des Scherausfalls auf vorhandenen Verbindungen, Verlängerung der kritisch orientierten Verbindungen und Ausbreitung der neuen Brüche durch vorher intakten Felsen. Herkömmliche numerische Codes nehmen normalerweise entweder ein kontinuum oder discontinuum Annäherung an; dieses ergibt häufig bedeutende Übervereinfachung und kinematische Beschränkungen, besonders wenn es kompliziertes Felsenmasseverhalten in der Nähe der Aushöhlungen modelliert. Dieses Papier beschreibt die Resultate von einigen Fallbeispielen mit einem kombinierten begrenzten Element - getrennten Elementcode, ELFEN, das einen Sprungausbreitungmodus enthält. Durch den Gebrauch von vorgewählten Felsentechnikbeispielen, demonstrieren die Autoren das Potential des Codes in der realistischen Simulation des komplizierten Felsenausfalls bei Anwendungen für beide Tagebaue und Untergrundsaushöhlungen.

Jan 1, 2003

By K. Meyer

"The largest cost centres of the David Bell Mine concentrator are grinding, leaching and effluent treatment. Optimizing results during the 6th year of operation are listed below: o SAG mill slurry density control and operating strategies improved liner life and media consumption by 10 and 25%, respectively.o Poly-met liners clad the SAG mill except for the feed end. Lower noise levels and reduced mill downtime have resulted in an improved and more efficient workplace (time required for liner changes is 2 to 3%).o A comparative grinding media study using seven different marked media at the same time showed media wear rates range 120 to 198 mg/kWh and ball mill charge replacement frequencies of 8.3 to 13.1 per year, and that a meaningful wear test must include all media to be tested at the same time in the same mill. High quality carbon steel cylinders had the best economics.o Pre-aeration, using pure gaseous oxygen is accomplished in pipe reactors. Small bubble generators provide oxygen in the first three leach tanks. 1500 to 3000 kg of oxygen is consumed per day. Leach kinetics have improved and trends indicate increases in gold recovery of three to seven ounces per day at reduced costs. Effects of reduced cyanidation of accessory metals on the effluent treatment plant will be discussed in a separate paper."

Jan 1, 1991

By J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly In the form of byproduct salt cake from the acid manufacturers, has been tending to decrease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This dean is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorable situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4 ? 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting, even the dehydrated product to market is the deciding economic factor. Therefore, the recovery oil production of anhydrous sodium sulphate from plant-.waste liquors or from natural brines of suitable composition might be economically feasible. The U.S. Bureau of Mines, at its nonmetallic Minerals Experiment Station, New Brunswick, N. J., has, for a number of rears, been investigating the commercial possibilities of treating the complex saline mineral polyhalite (K2SO4?NgSO4?2CaSO4?2H20) for the recovery of potash and magnesia. Certain proposed processes (1, 2, 3, 4)4/ yield waste liquors that contain the bulk of the magnesium and sulphate originally combined as magnesium sulphate in the polyhalite molecule. Sodium chloride In limited concentrations is also present, as extensive beds of salt occur in strata overlying the polyhalite deposits. A typical waste liquor would contain:

Jan 1, 1936

By Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-proof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges.

Jan 1, 1974

By Hookings H. J

UNDER a contract relating to the sale of a Broken Hill concentrate, the differentiation between granular and slime concentrate is determined by the proportion of the material which will pass a 200-mesh (I.M.M. standard) screen, and this has led to considerable attention being devoted to the question of laboratory sizing tests with screens of this order.It was found that many of the screens turned out by the makers during the war, and also since its termination, did not conform with the I.M.M. specifications as closely as some supplied in pre-war days. A perfect screen is hardly to be expected, but when the above contract was framed the parties anticipated that, by special care being taken during manufacture, a screen at least as good as the best pre-war screens would be available. This, however, has not proved to be the case, and the large irregularities in screens recently supplied render them useless for sizing determinations under the contract. The makers were approached through the Institution of Mining and Metallurgy, London, with the view of obtaining a few screens conforming as closely as possible to the 200-mesh I.M.M. standard, and in response to a request twelve pieces of screen were...

Jan 1, 1922

By Greg S. Williams, Richard W. Givens

This paper examines the effect of prill size consistency, internal panicle density, and oil absorbency on Ammonium Nitrate Fuel Oil (ANFO)-emulsion blends. By analyzing these physical properties of prill and the nature of the blending process, a mathematical model has been developed to theoretically predict blend densities. Calculated densities can now be compared to actual field densities to give an operator a basis for comparing various manufacturers’ emssions and Ammonium Nitrate (AN) during bid solicitation. The lowest priced emulsion and/or AN may not be the most economical, due to the impact of specific physical characteristics. These factors dictate the blending mechanics and resulting density yields for various mixes. The research was driven from observed ‘field’ mixing relationships and data. Ultimately, such a model can be an effective tool in evaluating blends from a cost and performance basis.

Jan 1, 1992

By Walter W. Kaufman

This Bureau of Mines manual for design of surface mine haulage roads covers such aspects of haulage road design as road alinement (both vertical and horizontal), construction materials, cross slope, and drainage provisions. Traffic control and design of proper lane widths to promote safe vehicle movement are included, as are suggested criteria for road and vehicle maintenance and for runaway-vehicle safety provisions. The aim of this publication is to provide those involved with surface mine haulage road design with a complete manual of recommended practices that, if implemented, will promote safer, more efficient haulage routes.

Jan 1, 1977

By P Duplancic and C R Lilley, R Hudson, D Beck

For deep block and panel caving mines, undercut or extraction level instability can have as much impact on overall recovery as underbreak or the premature ingress of waste. If the area of the mine affected by excessive convergence is small, recovery is usually possible. However, there are several examples of entire blocks that were abandoned prematurely due to footprint collapse. Clearly, such global instability has a major impact on recovery and must be avoided – this is one of the essential tasks for the design team.The design problem is complex. The planning engineer must ensure that the footprint has sufficient capacity to withstand the maturing loads in the cave, accounting for the effects of stress path, geological structures and the rock mass conditions. These are often uncertain and only sometimes quantified.The demand on the footprint will also be influenced by decisions and actions taken during production, especially related to draw, which can worsen a developing problem. Perhaps most importantly, the design decisions that favour stability and lead to lower deformation also negatively impact on idealised cave flow. Many engineers aim to minimise the size of extraction level pillars, to improve theoretical future resource recovery but in fact this can reduce recovery if widespread deformation ensues due to the undersized pillars.In 2014, PT Freeport Indonesia undertook detailed numerical analysis to quantify the effects of variability in rock mass conditions and geological structure on overall footprint performance. The analysis accounted for a range of stress paths and maturing cave loading scenarios sourced from a calibrated whole-of-cave deformation-flow model. The intent was to replicate some of the diversity and distribution of pillar deformation outcomes that may be seen in practice at Freeport.The discontinuum finite element analysis was able to replicate damage localisation around persistent structures, a realistic distribution of drive deformation and show how small areas of instability can evolve into major problems if poorly managed. The limits of pillar size and ground support as solutions to a number of different instability problems was also investigated, showing that pillar size alone was not a sufficient remedy for all adverse circumstances.In this paper, we describe the workflow for numerical analysis of footprint deformation. We discuss the compromises and considerations for balancing the sometimes competing needs for efficient extraction levels pillars, ground support and prudent draw strategy.CITATION:Beck, D, Hudson, R, Wilson, A D, Duplancic, P and Lilley, C R, 2016. An investigation of factors affecting the long-term reliability of extraction level pillars in deep block and panel caves, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pres-sure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By P. M. Ambrose, A. C. Fieldner

This , the 11th annual report of research and technologic work conducted by the Bureau of Mines on coal and coal products , is issued following the closing of the Bureau's war work on fuels and contains references to most of the published articles containing results of war investigations . The few remaining papers will be discussed in next year's report . The trend in coal research in the Bureau of Mines was discussed in Mechaniza- tion . This publication , covering the period from the close of armed con- flict to resumption of normal coal -research activities , includes a section never previously presented . There is included for the first time a discussion of the Bureau's activities in the Liquid Fuels and Lubricants and the Solid Fuels Subcommittees of the Technical Industrial Intelligence Committee . This report does not replace the more comprehensive ones prepared by individual authors and listed as footnote references in this publication . purpose is to bring to the reader a résume of the work for the fiscal year ended June 30 , 1946. The material presented herein is based largely upon publications , but the results of some research and testing, which would not otherwise be published in the near future, are presented in detail .

Jul 1, 1947

By J. Visman

"The Compound Water Cyclone is a concentrator for the wet processing, in bulk, of finely divided materials such as slack coal, fine ores and mineral sands. It was originally developed by the Fuels and Mining Practice Division of the Mines Branch, Department of Mmes and Technical Surveys, Ottawa, for the cleaning of friable slack coals and slurries.Since its introduction in the coal industry in 1962, its application to other materials has also been studied, with special emphasis on simplicity of operation and low over-all cost per ton of finished product .In this paper, a description is given of commercial two-stage units presently available for the processing of granular materials, including wastes a1:1d other low-grade products. A pneumatic control system is used for operating the cyclone under back pressure .and for automatic cut-point adjustment. An account is given of results obtained on coal mineral sands and ores in the Wes tern Regional Laboratory of the Department of Mines and Technical Surveys. Results of several industrial applications are discussed."

Jan 1, 1966

By R. H. Fernald

In 1900, as far as available records show, there were only two producer-gas power installations in the United States. In June, 1915, the number probably exceeded 1,000. Of this number, some 84.5 per cent comprised small plants using anthracite, and only about 15 per cent of the total number utilized bituminous coal and lignite. In addition to these, two plants used wood, and three or four used oil. In the main, however, the larger sized units are operating on bituminous coal and lignite. During the early years of these plants little success was anticipated from the use of bituminous coals and lignites, but in 1904 and 1905 it was fully demonstrated at the Government testing station at St. Louis that these fuels could be utilized to excellent advantage. However, although many producer-gas plants in daily operation are using bituminous coal and lignite, many power-plant men are still skeptical regarding the successful commercial use of these fuels.

Jan 1, 1916

By Pat McLaughlin

Environmental constraints are pushing many operators to change from large rotary blastholes to the smaller diameter holes drilled with down-hole or top-hammer rigs. Productivity improvements over the years with these two drilling techniques has taken some of the bite out of the transition, while improved fragmentation and more uniform muck due to the tighter patterns can help offset increased explosives costs.

Jan 1, 1995

By Bryan Buchholz, N. Kumar Kittusamy

Previous studies indicate that operators of heavy construction equipment are afflicted by musculoskeletal injuries of the arms, shoulders, neck, and lower back. These injuries appear to be due to excessive periods of sitting (static posture), work intensity, whole-body vibration, high resistance levers, repetitive motions, and awkward postures. (2-5) Although numerous studies have shown an association between operation of heavy construction equipment and symptoms of musculoskeletal disorders, very little research has been performed that systematically characterizes operating engineers' exposure to ergonomic hazards. The objective of this study was to systematically characterize the ergonomic hazards associated with excavating operations. As such, the following were performed: (1) vibrations were measured at the operator/seat interface (X, Y, and Z axes), and at the floor of the cab (Z axis); (2) psychophysical ratings of whole-body vibration (WBV) level and overall seat design were obtained; and (3) postural assessments of the job were made. Methodology This study evaluated an inexperienced female operator performing excavation, utilizing two different pieces of equipment. The operator was 37 years old, 162 cm tall, and weighed 80 kg. She had approximately 15 hours of operation time (experience) on the equipment evaluated. The two pieces of equipment used were: a Case Super 580E (1986) backhoe/loader, and an Insley H-2000 excavator (1975) (see Figures 1 and 2). More evaluations were performed on the backhoe/loader than on the excavator. The following evaluations were performed on the Case equipment: 1) vibration levels at the seat and floor; 2) psychophysical ratings of the overall seat design and vibration levels (for the task duration, and for an 8 hour duration); and 3) postural assessments. For the Insley equipment, all of the evaluations were performed except vibration measurements. When the evaluations were conducted, the following environmental conditions were noted: the temperature was 31°F, and soil and terrain conditions were rough and frozen.