Search Documents

By P Jones

Fosterville Gold Mine is an underground operation located approximately 20 km northeast of Bendigo and 170 km north of Melbourne. Fosterville is the most productive gold mine in Victoria, producing over 100 000 ounces of gold annually. Access to the underground is via two portals cut into previously mined open pits. Fosterville is 100 per cent owned and operated by Northgate Minerals, a gold and copper producer with mining operations, development projects and exploration properties in Canada and Australia. (Northgate Minerals Corporation, 2010).Underground operations commenced in 2006 with ore production focused on three orebodies – Phoenix, Ellesmere and Falcon. Primary ventilation to the existing operation is provided by wall mounted exhaust fans located underground. This system provides approximately 220 m3/s of primary ventilation to the operations with intake achieved through the portals. Exploration drilling during recent times has uncovered another lode, the Harrier orebody, located 2.2 km to the south of the existing workings. Due to the location of the new Harrier orebody, vent analysis revealed the requirement for a separate source of primary ventilation to service Harrier. Figure 1 shows a current underground long section and the location of Harrier in relation to the existing workings. A number of options were considered, including a parallel decline from one of the existing two portals, however, a 4 m diameter, 350 m deep surface ventilation shaft was selected as the most suitable and feasible option for the mine.In December 2009, geotechnical drilling commenced to determine the most suitable location for the shaft. Site locations were constrained by a number of factors including interaction with current and planned surface infrastructure as well as proximity to nearby community members at the southern end of the mining lease. Results from the geotechnical drilling indicated that the majority of the proposed shaft would be suitable for a 4 m raise bored shaft. However, the top 40 m of the proposed shaft were deemed unsuitable for raiseboring due to zones of weakness that would likely influence the stability of a 4 m diameter shaft (Robinson, 2010). Following independent geotechnical advice and input from experienced raiseboring contractors, it was decided to construct a 40 m presink prior to raiseboring activities.A crane mounted auger was chosen as the preferred method to construct the presink. This method differs substantially from traditional blind sinking methods which are highly labour intensive. The auger, or drill, is designed and built to be attached to a crane base using engineered pivoting cradles. The auger is suspended from the crane jib by pennant ropes attached to hydraulic rams. The auger applies rotation and axial loads to the drilling tools via a telescopic steel bar (Kelly Bar). Drill tools are attached to the bottom of the Kelly Bar and comprise an assortment of drilling buckets and reaming barrels. Drilling buckets cut in situ material and collect the spoil for removal and are used for the excavation of the ‘pilot hole’. Reaming barrels are used to expand the diameter of the excavation by directing cuttings into the pilot hole which are then removed by the drilling bucket. In June 2010, the presink was constructed utilising a crane mounted auger with support to the shaft walls applied via a remote fibrecrete unit. The excavation method involved cutting a series of smaller diameter holes (2.4 m wide) before reaming out to the final diameter (4.7 m wide) in 4 - 5 m vertical increments. Fibrecreting activities were carried out on the backshifts, to ensure the stability of the excavation and minimise interaction between the two units. The presink was completed on time and offered many advantages compared to traditional blind sinking methods, including safety, costs and timing. This paper will examine the benefits of this method as well as lessons learnt and future applications in the mining industry.

Mar 21, 2011

By Igor Zh. Bunin

A model for developing electric discharges between sulfide mineral (pyrite) particles under high-voltage nanosecond pulses in a liquid medium (water) is considered. A possibility of electrical breakdowns of liquid gaps between particles under nanosecond pulses is shown. This probability and the energy released in discharge channels depend strongly on the sulfide conductivity.

Jan 1, 2010

By Lyn Jones, Mike Bratty, Rick Lawrence, David Kratochvil

"The treatment of water is required at many mining operations to remove metals and prevent the discharge of contaminated water to the environment. In other cases, water treatment is used to provide better quality water for recycle to the processing plant, or to process bleed streams in hydrometallurgical operations in order to prevent deterioration in metallurgical performance or process equipment. BioteQ Environmental Technologies Inc. has developed and commercialized the BioSulphide® Process which can provide an alternative for these treatment needs and which can also be used for profitable metal recovery, particularly in cases where conventional metal winning techniques are not economical. The BioSulphide® Process is a high rate anaerobic biotechnology for on-site production of H2S from sulphur species, although for smaller flows and metal loadings, the use of chemical sulphide reagent might be more cost effective. Both new projects and existing commercial operations, used for removal and/or recovery of copper, nickel, and zinc, and which range in sulphide generating capacity from 50 kg/day to 3.7 tonnes/day, are discussed. Particular focus is placed on the results of operations at the Raglan Mine in Northern Quebec where dissolved nickel is removed from contaminated water at a high efficiency through the precipitation of nickel sulphide. Plant effluent is discharged directly to the receiving environment and the high-grade nickel sulphide product is combined with the nickel flotation concentrate produced at the mine. The plant at Raglan will replace the existing conventional water treatment plant and will eliminate the need for on-site storage of treatment plant sludge.INTRODUCTIONThe BioSulphide® Process, which produces low cost H2S for use in selective metal precipitation, offers a low capital cost alternative which can operate efficiently and cost-effectively within a wide range of flows and solution grades. Since the technology can be used to recover metals from solutions with low flows and metal grades, the technology is also applicable to environmental applications for water treatment, with the sale of recovered metals providing an offset to treatment costs. For environmental control, the technology has a distinct advantage in being able to meet strict effluent discharge criteria due to the very low solubility of metal sulphides. To date, BioteQ Environmental Technologies has designed and constructed three plants for metal sulphide precipitation, with another three projects in the advanced development stage."

Jan 1, 2006

By Adam Chrzanowski, Eugene E. Derenyi, Peter Wilson

"The rapid growth of the mining industry in Canada necessitates a reevaluation of existing mining surveying techniques and the development of new methods. In this connection, the Department of Surveying Engineering at the University of New Brunswick initiated a research program, and the major points of investigation conducted to date are as follows: 1. Based on practical experience and theoretical studies, all factors influencing classical shaft-plumbing procedures were analyzed. Refined methods were developed to increase accuracy. 2. The performance of electronic and optical distance-measuring instruments in underground conditions were investigated. In this connection, test measurements were made in various mines, employing four types of Tellurometers, two models of Geodimeters and a proto-type optical range-finder. 3. Tests were conducted and methods developed for the mapping of large underground chambers by photo-grammetric means. The aforementioned points are discussed at some length in the paper. The authors have also indicated areas where further research is needed and suggested ways and means to improve and modernize mining surveying as a whole throughout Canada."

Jan 1, 1967

By Chuck Edwards

"Cameco operates the high-grade McArthur River uranium mine in northern Saskatchewan, and is constructing the high-grade Cigar Lake uranium mine. Cameco has studied the concept of underground milling of high-grade uranium ore. Compared to conventional milling on surface, the underground milling scheme appears to offer significant cost savings and a lower environmental impact. This paper describes the underground milling scheme, presents process flowsheets and plant layouts, and provides an assessment of potential benefits from underground milling.INTRODUCTIONCameco CorporationCameco is the world’s largest uranium producer, with three operations in Saskatchewan (Rabbit Lake mine/mill, McArthur River mine, and Key Lake mill), two in the United States (Crow Butte and Smith/Highland ISL operations) and two new mines being developed in Canada (Cigar Lake project) and Kazakhstan (Inkai project). Cameco provides uranium fuel refining and conversion services at its Blind River and Port Hope facilities in Ontario. Cameco is part owner (31.6%) of Bruce Power that leases eight nuclear power plants located in southern Ontario. Cameco is the majority shareholder in Centerra Gold Inc., which operates gold mines in the Kyrgyz Republic and in Mongolia.Global Uranium Production RequirementsCentral to Cameco’s view of future uranium supply requirements is the belief that the world is experiencing a nuclear renaissance. This belief is supported by a number of developments, including:•,?Countries representing half the world’s population are now constructing new nuclear power plants. Many countries without nuclear power have begun to plan for it, seeking reliability, clean air and energy independence.•,?Accelerated growth for this industry is also becoming much more likely. In Asia, primarily in China and India, 92 reactors are under construction, on order or planned to help meet rapidly expanding economic needs. Other Asian countries, such as Vietnam and Indonesia, with large populations and rapidly growing economies, are also expected to follow.•,?In the United States the “Energy Policy Act of 2005”, the first energy legislation introduced in over a decade, was signed. This legislation includes provisions recognizing, for the first time at a national level, the clean air contribution of nuclear energy and its critical role in meeting energy security. Upon signing this landmark legislation President Bush stated, “We will start building nuclear power plants by the end of this decade.”"

Jan 1, 2007

By N. I. Aziz

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack orientation.

Jan 1, 1992

By Joshua Hoffman, Braden Lusk, John Rathbun

A Flyrock Prevention Taskforce was established in Kentucky with the support of Kentucky's Department of Natural Resources, Kentucky's Explosives Industry, and the University of Kentucky. This paper presents the initial work of the Flyrock Prevention Taskforce towards its missions of identifying the root causes of flyrock incidents based on the analysis of previous events, and tracking the progress of flyrock elimination in the future. Work identifying root causes of flyrock events is presented through the development of a database which manages information about the blasts which caused flyrock. This data includes: blasting and seismograph records, drill logs, videos of the event when available, company notes/incident reports, and any additional information regarding probable cause. Work tracking the progression of flyrock elimination efforts is presented in this paper through the introduction of a flyrock index. Several metrics are proposed for this index, and are discussed for their appropriateness and shortcomings. In order for these indexes to be valid forms of tracking flyrock incident rates additional records must be kept and reported, such as the annual consumption of explosives by surface coal blasting. Suggestions for record keeping, flyrock investigation practices, and means of tracking flyrock incident rates are proposed in this paper.

Jan 1, 2013

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By John E. Lens

How much trouble can narrow vertical fissures in bedrock cause on a shallow bedrock site? Enough trouble so end-bearing H-piles range between 8 and 100 feet long in a single pile cap and tiebacks range from 40 to over 100 feet long within a 10 foot wall span. Sloped bedrock surfaces also complicated the tieback installation as the drill casing followed the sloped rock surface while drilling and caused unanticipated bending (and sometimes breaking) of the drill string. Warned via pre-construction rock probes and cores reaching over 80 feet deep at the Winooski, Vermont project site, the design and construction team expected anomalies in pile driving and tieback drilling due to fissures in the bedrock filled with soil and weathered-rock. The degree of abruptness in the variability in the rock surface, and its impact on pile driving and tieback drilling were less predictable. Close monitoring of pile and tieback installation, redesign of pile caps, and lengthened tiebacks overcame these anomalous fissures. This paper shares the lessons learned for overcoming these geologic challenges to benefit designers, contractors bidding the work, and ultimately, the owner, with lower contingencies.

Jan 1, 2006

By Y Xiao, C Lei, C Shu, W Wang, K Wang, J Deng

To investigate the effect on coal spontaneous combustion with high geo-temperature, an experimental apparatus was developed to measure characteristic parameters of two kinds of coal samples at different temperatures: one was 40°C (G coal sample) and the other was a rising temperature from room temperature (C coal sample). Based on the relationship between CO concentration and the temperature variation, a calculation model of the apparent activation energy of coal was established. The results indicated that the oxygen consumption rate, the generation rate of CO and CO2, and heat release intensity of G coal sample were higher than C coal sample. This trend was more and more obvious as the temperature increased. Furthermore, the apparent activation energy of G coal sample was lower than C coal sample, especially at low temperature stage, which demonstrated that the more the oxidation and exothermic reaction of G coal sample was enhanced, the less energy was required to break the barrier of oxidation reaction. Under the same condition, the speed of oxidation reaction was faster for the coal in the high geo-temperature environment, which was more liable to spontaneous combustion.CITATION:Lei, C, Deng, J, Xiao, Y, Shu, C, Wang, K and Wang, W, 2017. The effect of high geo-temperature environment on spontaneous combustion – an experimental study, in Proceedings Australian Mine Vent Conference 2017, pp 137–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Jon Sinnreich

Ensuring the accuracy of collected data during deep foundation static load tests is of paramount importance. Typically, pile head displacements are measured relative to a purpose-built reference system, which is assumed to be fixed. This study presents a simplified error analysis of this assumption, illustrates the potential magnitude of these errors, and proposes an improved method of pile head displacement monitoring.

Jan 1, 2009

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10µm. The current study examined the effects of operating conditions on centrifuge performance. The test conditions included centrifuge bowl and scroll speeds, volumetric feed rates, solids concentration, and pond depth. Centrifuge performance was evaluated using partition curves, along with product yields and solids concentrations.

Jan 1, 2000

By Sakai Kunito, Nigel B. Sugden

If an Earth Pressure Balance (EPB) TBM is operated effectively tunneling can be carried out producing negligible ground movements. Using the methods given in this paper face losses of the order of 0.5% and less are generally obtainable using an EPB. Operating the EPB TBM in this manner reduces the requirement for the building protection measures used to protect surface structures. This can result in a considerable cost saving for the construction of a tunnel under built up areas. This paper to give guidance on the causes of ground movements around a TBM and the methods of running an EPB TBM that will minimize those movements. Details of how this was successfully done during the construction of the Bangkok Metro are given. The paper is split into three parts as below. 1.Causes of ground movements due to TBM tunneling 2.Methods of controlling those movements using an EPB TBM 3.Case history Bangkok Metro (water main)

Jan 1, 2001

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By Alfred Bellows

The objective was to develop and design a remotely operated temporary roof support system that provides a safe working environment between a freshly cut coal face and the last line of permanently supported roof in which to perform roof bolting activities. This system was to take the form of a retrofit package which could be adapted to a majority of the bolters currently in service. The result is an integrated piece of hardware which will retrofit onto virtually all single boom bolters by removing the drill boom and relocating and modifying the hydraulic controls. The system is composed of three basic components: a pair of cantilevered roof supports which reach forward to the desired line of support, a mast type drill unit for drilling holes and torquing bolts, and a transverse slide assembly to carry the drill from hole to hole across the entry without relocating either the bolter or the roof support. A converted bolter not only provides a much safer operation but is projected to increase the production speed as well as reduce the manpower required to operate a section.. This improvement in productivity is shown to make the job of retrofitting a bolter cost effective in less than two months and provide a potential profit thereafter. Based on the findings presented in this report it is recommended that a proto-type be built and tested in an underground coal mine to demonstrate its effectiveness.

Jan 1, 1976

By Ted J. Williams

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

May 1, 2007

By Erle C. Donaldson

Subsurface injection of liquid and slurry-type industrial waste is being used as a means of waste disposal. This survey conducted by the Bureau of Mines shows that the method can be economically and environmentally attractive if the proper precautions are taken, especially when the alternative is cursory treatment and discharge at the surface. Attention is called to petroleum technology and experience that can be applied to subsurface waste injection. Part 1 of this report is a discussion of the general aspects of subsurface waste-injection systems. Part 2 is a general discussion and review of the literature concerning the geologic formations available for injection in the United States. Part 3 is a discussion if 15 case histories including information on the source and nature of the waste and the geology, surface equipment, well completion, and operation of the systems.

Jan 1, 1974

BATMINÖ, BATMINEÖ, BATMINDÖ are an abbreviation for Business Analysis Tools for Mining, Mine Evaluation and Mine Design respectively. BATMINP are proprietary tools customised to suit individual client requirements. The first suite of tools provides for analysis and evaluation of open pit mining equipment alternatives and includes fleet selection, fleet sizing and production, productivity and economic outcomes. The models address all mine process activities including drilling, blasting, loading, hauling and auxiliary services. All models are built to provide for simultaneous evaluation of multiple alternatives that are time and condition related. Provision is made for modelling from first principles and/or default or shortcut inputs. Sensitivities to key input parameters are easily performed and consistent logic is applied throughout the process. The models are built to provide key outputs in a format suitable for presentation and documentation. Provision is also made in the models for validation of both inputs and outputs through benchmarking, back analysis and budget comparison. The same models can be used for short interval (12 month) planning and control, medium-term (three to five years) and long-term life-of-mine (LOM) planning. Millions of dollars are spent each year on mining plant and equipment. Decisions that impact on the medium and long-term are made. BATMINP tools have been used to perform studies with good results and in most cases the studies have been validated through back analysis and comparing model outcomes to real data.

Dec 6, 2010

By Arthur L. Hall

The purpose of this symposium is to challenge industry to better air classification, and as a first step toward fulfillment, to spotlight three fairly recent, aerodynamically designed, highly efficient air classifiers. This discussion does not intend to imply that present practice is bad. Actually, when present air separators are used for the jobs for which they were originally designed, they give high production and uniform operation, with a minimum of maintenance. The customers of nonmetallic mineral pigment producers, however, are making increasing demands for finer products, such as 99.9 pct -20µ, which appears to be beyond the economic capabilities of standard air separators industrially used over the last 10 to 30 years. Here is an actual example. A 10-ft diam pebble mill is in closed circuit with a conventional 12-ft diam centrifugal air separator, grinding 20-mesh wollastonite to a series of fine grades up to 99.97 pct - U.S. No. 325 mesh (44µ). Fig. 1 shows variations in fineness of mill discharge (or air separator feed), recycle for regrinding (or air separator tails), and product as measured by a wet rotating sieve test. For example, when the mill is turning out a product 80 pct -325, the mill discharge or separator feed is 30 pct -325, and the coarse tailings or recycle is only 5 pct -325. Hence 25 pct of the 30 pct available is accepted as product. This is efficient separation, and the ratio of recycle to feed is only about 2: 1. How- ever, to make a product testing 99.97 pct -325 the separator feed is 62 pct -325 and the coarse tailing 60 pct -325. In this case the recycle ratio is about 13: 1 and the economic limit to produce fineness has been substantially reached with this given equipment and process arrangement.

Jan 10, 1957

By Perry G. Cotter

As a portion of a general program for the synthesis of hard materials, a method was sought by which the hardness and density of tungsten carbide (WC)-cobalt compacts could be increased. It was demonstrated by Cotter that these improvements in quality could be made by employing an electric-resistance sintering process in which heat and pressure are applied simultaneously to presintered compacts composed of powdered tungsten carbide and cobalt. This conclusion was based on tests of material prepared by Cotter on welding equipment in use at the U. S. Naval Engineering Experiment Station, Annapolis, Md., and at Rensselaer Polytechnic Institute, Troy, N. Y. Rockwell-hardness tests made at Norris and core-drilling tests made at the Mount Weather Station of the Bureau of Mines indicated that, for some purposes, carbide material made by this process might be superior to the chemically analogous commercial products prepared by ordinary sintering methods. A program to develop optimum conditions for the electric-resistance sintering of tungsten carbide-cobalt compacts was initiated. The program was followed by a systematic evaluation of the hardness and density of compacts prepared by this method along with a series of carbide compacts furnished by various manufacturers. This paper presents a description of the electric-resistance sintering of tungsten carbide-cobalt compacts and the results of comparative physical tests.

Jan 1, 1955