Search Documents

By William Porter

Hand scaling is a physically demanding job and is responsible for numerous overexertion injuries in mining. This experiment studied rib scaling from an elevated bucket to examine force generation capabilities and electromyographic responses to a prying subtask. Subjects exerted force using two bars (steel and fiberglass) at five target heights. Work height significantly affected peak prying force during scaling activities with highest force capacity at the lowest level (p = 0.0188). Bar type did not affect force generation (p = 0.7843): However, use of the fiberglass bar required significantly more muscle activity to achieve the same force (p < 0.05). It was concluded that miners should scale points on the rock face that are below their knees, and reposition the bucket as often as necessary to do so. Additional research is needed to fully understand the impact of bar type on the physical demands of an entire scaling task.

Jan 1, 2006

By Robert B. Johnson

The refraction seismic method has been used as an indirect means of exploring for fluorspar in southern Illinois by the Illinois State Geological Survey. Use of the method has been restricted to those areas where mineralization is associated with faults, a restriction necessitated by the operating principles of the refraction method. The seismic data enable the interpreter to locate fault zones in the subsurface and, under ideal circumstances, to make estimates of dip direction and magnitude and vertical displacement provided the local stratigraphic units are known and are geophysically recognizable. In this instance, refraction seismic exploration has been successful in the surface mapping of well-developed faults, both simple and complex with which fluorspar may or may not be associated. However, less clear results have been obtained where faulting has been less severe and where there are numerous accompanying mineralized joints.

Jan 1, 1964

By Thomas M. Barczak

Advancements in support technology have occurred to a large extent because of the demands of the mine operators. Shield supports are no exception. The most notable changes in shield technology in the past decade have been increases in shield capacity and life expectancy, which have increased by a factor of 4 and 7 respectively since the inception of the shield support 25 years ago. The purpose of this paper is to set goals for the future generations of longwall shields. These goals include: (1) 100,000 cycle life expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control with adjustable setting pressure algorithms, (4) composite material design to reduce weight and increase shield width, (5) constant set leg cylinder design, (6) improved joint design to reduce wear and stress, (7) advancements in leg cylinder socket design, and (8) an instrumented shield to measure in-service structural component loading. These design issues will continue to push the envelope in longwall shield technology that has provided the safest and most productive mining system employed in the history of mining. In preparation for this, a historical examination of shield failures is made and recent trends in shield design are evaluated. Design practices to improve structural margins of current designs are also addressed.

By B. W. Dunning

This paper describes studies conducted by the Bureau of Mines to achieve its goal of developing methods for increased recovery and utilization of valuable constituents in a wide variety of domestic and industrial wastes, In this particular study, 36 units of obsolete electronic equipment from military aircraft were disassembled into their modular components by hand to determine materials distribution. Further modular disassembly into individual parts was used to identify metal composition. After identifying the metals in some of the more difficult to dismantle modules, similar modules were grouped together, shredded, mechanically separated, and using metal composition data from hand separation, classified along with the hand-separated materials. Although this equipment is normally classified as law-value iron-bearing aluminum, data were obtained that indicated the potential for moderately higher value classification. The electronic units were classified as to precious metals, copper, iron, and aluminum contents, and scrap values were estimated.

Jan 1, 1980

By C. P. Haller, S. J. Aresco, R. F. Abernethy

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash- softening temperature of ash, the free-swelling index, and the hardgrove grind- ability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instruc- tions issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the con- tractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal. The Government purchased approximately 5-1/4 million tons of coal in fiscal year 1953. In connection with these purchases, the Bureau analyzed 11,435 samples. These are published for the use of Government officials and the public. A series of publications has been completed on coal analyses by States, or, where production is small in any one State, by groups of adjacent States. In addition to analytical data showing composition and quality of coals of the States, the publications con- tain brief descriptions of the geological structure of the coal basins, typical mining conditions in the various districts, the principal economic data of the industry, and the relationship of mine or channel samples to delivered and tipple samples. The present publication covers many States but deals only with the analytical data of the coals. Previous publications in this series are: Bulletin 516, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Years 1948 to 1950 Inclusive); Report of Investigations 4934, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Year 1951); Report of In- vestigations 4972, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Year 1952). Following are the Bureau of Mines technical papers published by States, with their numbers: Alabama, 347; Alaska, 682; Arizona, California, Idaho, Nevada, and Oregon, 696; Arkansas, 416; Colorado, 574; Illinois, 641; Indiana, 417; Iowa, 269 and 706; Kansas, 455; Kentucky, 308 and 652; Maryland, 465; Michigan, North Dakota, South Dakota, and Texas, 700; Missouri, 366; Montana, 529; New Mexico, 569; Ohio 344 (and Bulletin 499); Oklahoma, 411; Pennsylvania Bituminous, 590 (Supplement 645); Pennsylvania Anthracite, 659; Tennessee, 356 and 671; Utah, 345; Virginia, 365 and 656; Washington, 491 (Supplement 618); West Virginia, 405 and 626; and Wyoming, 484.

Jan 1, 1955

By Gary B. Glass

Seventeen percent of US coal production now comes from the 19 surface coal mines in the Powder River Basin of northeastern Wyoming. The Powder River Coalfield, which coincides with this topographic and structural basin, is unique to the conterminous US, in that it contains an estimated 934.4 Gt (1.03 trillion st) of in-place coal resources. At least 13.2 Gt (14.6 billion st) is a compliant, strippable reserve base. In 1993, an estimated 162 Mt (179 million st), or 98% of the coal mined in this Wyoming coalfield, came from the thick - average 30.5 m (100 ft) - subbituminous, Wyodak coalbed, or from the Anderson and Canyon coals in the one mine where the Wyodak is split into two separate coalbeds. The other 2.7 Mt (3 million st) of coal mined in the Powder River Basin in 1993 came from the School, Badger, Monarch and Deitz No. 3 coalbeds. In this "world class" coalfield, there are at least 13 other persistent, 3 to 15 m (10 to 50 ft) thick, coalbeds as well as the Big George and Lake De Smet coalbeds, which are each 61 m (200 ft) or more thick in places. None of these latter 13 coals are mined at this time.

Jan 1, 1994

By George H. Johnson

This report describes the procedures and summarizes the results of an investigation of surface subsidence above caving blocks at the San Manuel mine, San Manuel, Ariz., in order to obtain quantitative information on subsidence and ground movement caused by mining large volumes of ore. This investigation is one part of an overall study of rock mechanics being undertaken by the Bureau of Mines. Attention was given to the improvement of a rapid and precise method of surveying a large number of subsidence pins and cracks in the surface terrain. Photogrammetric methods were used as an adjunct to the triangulation subsidence surveying as well as in ordinary topographic work Maps of various kinds were prepared to show the results obtained. The computation of the survey notes was programed for an electronic digital computer at a saving of time and expense over the use of a desk calculator and trigonometric tables.

Jan 1, 1963

By T. Takayama Filho

Votorantim Metais Zinco is a smelting facility which produces SHG zinc, zinc alloys, sulfuric acid, liquid SO2, copper sulfate, cadmium metal and silver concentrate. It is located at Juiz de Fora, Minas Gerais State, Brazil. This facility has been operating since 1980 and its current capacity is 95,000 tonnes of zinc per year, using mostly imported sulfide concentrates.The plant uses the conventional roast-leach electrowinning (RLE) process, in which iron is removed from the circuit as jarosite. The residues generated by the RLE process, which amount to about 200 t/day (dry weight), were until 10 years ago, deposited in tailing ponds having no impervious lining. More recently, jarosite and other wastes have been deposited in a properly built reservoir, but this is reaching its maximum capacity. In order to decommission these disposal operations and to reclaim the sites in an environmentally acceptable manner, Votorantim Metais concluded in 2004 a rehabilitation project for the old tailings pond and prepared detailed plans for managing the current and future disposal of jarosite-bearing residues. This paper describes the procedure for removing iron from the hydrometallurgical circuit and discusses the past and current status of the residue disposal sites, as well as the future challenges related to the environmentally acceptable handling of iron residues.

Jan 1, 2006

By Cecil Q. Cupps

Results are presented of a comprehensive study of the characteristics of the original oil in the Weber sandstone reservoir, Rangely oil field, Colorado. Through the medium of subsurface sampling, adequately representative samples of the original reservoir oil were obtained from many parts of the reservoir over a period of 5 years concurrent with active development of the reservoir. Data of differential gas liberation, pressure-viscosity, and. pressure-volume-temperature relationships are shown for 12 subsurface oil samples. Data also are given of reservoir pressure and. temperature, composition of liberated or solution Gas, composition of 22 produced-gas samples, and Hempel analyses of crude-oil samples from 18 wells. The characteristics or physical properties of the 12 subsurface oil samples, as determined by laboratory analyses, were correlated with elevation of the top of the Weber sandstone. These relationships of oil characteristics to elevation in the reservoir show that only the oil in contact with the initial gas cap was gas-saturated at the existing pressure and temperature. The characteristics of the original reservoir oil were marked by an appreciable decrease of saturation pressure and solution gas-oil ratio and increase of viscosity and density with depth below the gas-oil contact. The composition of solution gas and of&apos; produced was also was found to vary with elevation of the oil in the reservoir.

Jan 1, 1951

By Mahmut Yavuz

to in Old Uighur Turkish as Tolay kopugu, in Ottoman Turkish as Derya kopugu, and in modern Turkish as Luletasi. Scientifically known as sepiolite, it is represented by the formula Si12Mg8O30(OH)4(H2O)4(8H2O). Sepiolite is a natural clay mineral composed of hydrous magnesium silicate, characterized by a structure of alternating blocks and tunnels that develop in the direction of the fiber. Each structural block contains two silica tetrahedral sheets surrounding a central layer of magnesium oxide- hydroxide. Sepiolite exists in two distinct forms in nature: alpha-sepiolite and beta-sepiolite. Alpha- sepiolite is amorphous, compact, and resembles pellets that look like sea froth, hence its Turkish name Luletasi. In contrast, beta-sepiolite appears as amorphous aggregates or small, flat, round particles. These two forms exhibit different physical properties. Meerschaum was also studied by Brauner and Preisinger in 1958, who agreed that it primarily consists of sepiolite (2MgO·3SiO2·nH2O). According to these researchers, water is present in its mineral, zeolitic, crystal, and structural forms. Meerschaum is commonly used for adsorbing various liquids, as an ion exchanger, and for dispersing and insulating paraffin in the chemical industry (Gokdemir and Dogan, 2011). Sepiolite deposits of the meerschaum type are primarily found in Turkey, Somalia, Tanzania, Kenya, and Mexico. Alongside high-quality, low-density, and highly porous meerschaum, Somalia also has sedimentary sepiolite formations. The total reserves of these deposits are estimated at around 50–100 million tons (Sariiz and Isik, 1995). Meerschaum, also known as “white gold” or “sepiolite,” is a unique mineral highly prized for its lightness, heat- resistant properties, and ability to be carved into intricate designs. Found predominantly in Eskisehir, Turkiye, meerschaum mining and processing have become significant contributors to the local economy and cultural heritage. This paper explores the history, economic importance, mining practices, and environmental impacts of meerschaum mining in Eskisehir and discusses the challenges and opportunities faced by the industry.

Feb 1, 2025

By R. L. Wilcox, M. L. Fuller

MOST commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper2 of this series, and in this paper, aging phase changes of zinc alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evaluated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0.03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change,

Jan 1, 1935

By J. A. Finch, Zhenghe Xu

The competitive adsorption of xanthates on sulphide minerals in a binary mineral system (pentlandite and pyrrhotite) was studied using the pseudo-in-situ technique of attenuated total-reflectance FTIR spectroscopy. The minerals were placed in the same collector solutions, either separated by a glass wall or in direct contact with each other before magnetic separation and separate analysis. The effect of mineral interaction on xanthate adsorption was clearly demonstrated spectroscopically for the first time. At low concentrations of xanthate, its adsorption on pentlandite was activated by physical contact with pyrrhotite; the effect may be attributed to the enhancement of electron transfer through electrical contact between the two minerals. The results emphasise the need for caution in extrapolating results obtained from single-mineral studies to flotation practice

Jun 18, 1905

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017

By Stavros A. Argyropoulos

Exothermic mass transfer takes place in various areas involving metallic systems, ranging from liquid metal processing operations to the growth of thin films in microelectronics. The formation of intermetallic compounds plays an important role in the exothermic mass transfer of metallic systems. Two types of exothermicity are identified , namely , Microexothermicity and Macroexothermicity. The former is encountered when small amounts of metals are mixed, while the latter is exhibited when a solid metal in a lump form is added into liquid metal. In this paper two types of exothermic mass transfer in metallic systems will be presented and reviewed. Mathematical modelling work for these types of exothermic mass transfer will be analyzed.

Jan 1, 1993

By David R. Beadman

The Fleming method is widely used for the analysis and prediction of single pile behaviour under maintained loading. The method does not distinguish between bored and driven piles. Driven piling avoids the need to dispose of spoil from the pile installation and is therefore becoming increasingly attractive. This paper considers the theoretical effects of the possible preload at the base of a driven pile after installation, using the hyperbolic functions as defined by Fleming. The Fleming method is reviewed and the equations and analyses are adapted, using spreadsheets, to allow for a possible preload. The simplifying assumption of the effect of the elastic compression of the pile is also reviewed and a more analytical method adopted to assess the elastic compression. Some driven pile test data is analysed to consider the possible effects of the preload on the performance of a driven pile and to test the theoretical relationships that are developed in the paper.

Jan 1, 2006

By Paul Hatmaker

Diatomite is the name now generally given to a mineral substance composed of the tiny , skeletal remains of diatoms , which are microscopic , flowerless , water plants related to the algae ... This residuum is essentially hydrous amorphous silica. Common names for diatomite are : Diatomaceous earth , tripolite , kieselguhr , and infusorial earth . Strictly speaking , however , the latter material is not diatomite , as it is composed of the fossil remains of infusoria , which usually do not occur with the diatomaceae . Other synonyms for diatomite are : Diatomaceous silica , kieselmehl , bergmehl , diatomeenpeelite , polirschiefer , moler , molera , molererde , de smid earth , fossil flour , mountain flour , farine fossil , white peat , radiolarian earth , chalk rock, ceyssatite , randanite , and tellurine ; also various diatomite products of individual companies are known by their own trade names . Diatomite should not be confused with fuller's earth , for the two are separate and distinct substances . Bentonite , pumice , and tripoli , have also been used erroneously to designate diatomite . Tripolite , however , is a true diatomite formerly mined near Tripoli ..

Feb 1, 1931

By L. I. Gonzalez de Vallejo

SRC rockmass classification have been applied to 25 tunnels in Spain and Italy, for which it was found that much heavier supports than those estimated by the RMR index were required. SRC and RMR indices and other relevant geomechanical data were obtained during the site investigation and construction stages. Data corresponding to in situ stress measurements, analysis of tectonic structures, and instability problems arising during construction were used to asses the state of stress. The relationship between tunnel section convergence and the SRC and RMR indices was also analysed. Support measurements based on SRC and RMR classification were compared with those actually used during construction. These analyses indicate that for most of the tunnels examined, supports estimated using the SRC were much closer to those actually installed than those predicted by the RMR index. Bei der Verwendung des SRC-Systems zur Klassifizierung des Gesteins als Baugrund für 25 Tunnel in Spanien und Italien wurde festgestellt, dass viel schwerere Abstützungen benötigt wurden, als wenn die Beurteilung anhand des RMR-Systems angefertigt würde. Die Klassifizierung anhand des SRC- und des RMR-Systems, sowohl als auch andere wichtige geomechanische Daten wurden während des Ablaufs der Erkundungen und der Bauausführung gewonnen. Die Resultate der Messungen der Spannungen vor Ort, die Analyse der tektonischen Struktur und die Stabilitätsprobleme während der Bauausführung wurden dazu verwendet, um den im Felsgrund vorherrschenden Spannungszustand zu definieren. Das Verhältnis der Messungen der Tunnelkonvergenz zu dem SRC- und RMR-Index wurde auch analysiert. Die durch das SRC- und RMR-System vorhergesagte Grösse der Abstützung wurde mit der Grösse der Abstützungen verglichen, die am Bau letztlich verwandt wurden. Diese Vergleiche zeigen, dass für die meisten der studierten Tunnel die Vorhersage der Abstützungen, die anhand des SRC-Systems angefertigt wurden, viel näher der wirklich verwendeten waren als die Vorhersage anhand des RMR-Systems. SRC rockmass la classification ont été appliqué à 25 tunnels en Espagne et l&apos;Italie, pour laquelle il a été trouvé que des appuis beaucoup plus lourds que ceux évalués par l&apos;index RMR ont été exigés. SRC et des index RMR et d&apos;autres données geomechanical appropriées ont été obtenu pendant l&apos;enquête de site et les étapes(scènes) de construction. Les données correspondant aux mesures de stress(d&apos;accent) in situ, l&apos;analyse de structures tectoniques et des problèmes d&apos;instabilité surgissant pendant la construction ont été utilisées aux ânes(culs) l&apos;état de stress(d&apos;accent). Le rapport entre la convergence de section de tunnel et le SRC et les index RMR a été aussi analysé. Les mesures d&apos;appui basées sur SRC et la classification RMR ont été comparées avec ceux en réalité utilisés pendant la construction. Ces analyses indiquent que pour la plupart des tunnels examinés, les appuis évalués utilisant le SRC étaient beaucoup plus proches de ceux en réalité installés que ceux prévus par l&apos;index RMR.

Jan 1, 2003

By T. Saito, S. Murata

An original concept of JRC-diagram that can evaluate JRC and its size-effect by using a fractal model was proposed. In order to confirm the applicability of the JRC-diagram, first, JRC of the tensile fracture surfaces of a granite and a sandstone were evaluated by both the JRC-diagram and Barton&apos;s JRC-profiles, and then, it was compared with the JRC inversely calculated from the peak shear strength that is obtained from the shear test for each fracture using Barton&apos;s empirical equation. As a result, JRC evaluated by the JRC-profiles was much smaller than the inversely calculated JRC. On the other hand, it became clear that JRC evaluated by the JRC-diagram is almost the same with the inversely calculated JRC, if the size of interlocking is evaluated correctly. Therefore, for the JRC evaluation, it is thought that the JRC-diagram is more applicable than the JRC-profiles. Als ein neues Verfahren zur Bewertung des Rauheitsindexes JRC für die Bruchfläche von Felsenschichten anhand eines fraktalen Modells, wobei auch der Maßeffekt berücksichtigt wird, wird ein JRC-Diagramm vorgeschlagen. Um die Angemessenheit der Bewertung vom JRC mit diesem JRC-Diagramm festzustellen, wurden die JRC-Werte an einer Bruchfläche zwischen Granit und Sandstein sowohl mit dem JRC-Diagramm als auch mit dem herkömmlichen JRC-Profilverfahren bewertet. Anschließend wurden die durch die beiden Verfahren ermittelten Werten mit den JRC-Werten verglichen, die von den Schertestergebnissen mit Hilfe von Bartonschen Erfahrungsformel zurückgerechnet werden können. Daraus ergab sich, daß das JRC-Profilverfahren ziemlich kleinere JRC-Werte gibt als bei der Zurückrechnung, während die JRC-Werte durch das JRC-Diagramm unter entsprechender Bewertung des Ineinandergreifungsmaßes an der Bruchfläche beinahe gleich sind wie die zurückgerechneten Werte. Diese Tatsache weist darauf hin, daß das JRC-Diagramm eine bessere JRC-Bewertungsmethode als das JRC-Profilverfahren darstellt. Nous avons proposé le diagramme JRC, nouvelle méthode d&apos;évaluer JRC qui est un indice de rugosité superficielle d&apos;une fracture de roche à l&apos;aide du modèle de fracturation, compte tenu de son effet d&apos;échelle. Pour vérifier la validité de JRC évalué au moyen de ce diagramme, nous avons évalué JRC d&apos;une fracture de roche, granite et grès, par le diagramme JRC et le profil JRC, méthode conventionnelle, et les résultats ainsi obtenus ont été comparés avec la valeur de JRC calculée en sens inverse à l&apos;aide de la formule empirique Barton sur la base des résultats de l&apos;essai de cisaillement des fractures. Il en résulte que la valeur de JRC obtenue par le profil JRC était assez faible en comparaison avec la valeur calculée en sens inverse alors que celle de JRC obtenue par le diagramme JRC correspondait approximativement à la valeur calculée en sens inverse à condition d&apos;évaluer l&apos;échelle d&apos;endentement d&apos;une fracture. Par conséquent, nous considérons que le diagramme JRC est une meilleure méthode d&apos;évaluation de JRC par rapport au profil JRC.

Jan 1, 2003

By J. E. Tiffany, J. J. McKitterick

"IntroductionThe Bureau of Mines is investigating the fundamental factors in breaking down coal at the face, which govern the production of lump coal in typical mines working, different coal beds. Tiffany and Nelson in 1923-21 conducted tests on methods of blasting and use of different explosives, in a mine working the Pittsburgh bed in Pennsylvania. They determined come of these factors quantitatively, and compared their results with those obtained when the regular mine practice was followed.Results of Previous InvestigationThe tests by Tiffany and Nelson showed that the use of the cartridge of smaller diameter than that used in mine practice, resulted in an increase of 5 per cent in the amount of lump coal passing over a 1-1/4-inch bar screen, with a reduction of 32 per cent by weight in amount of explosive required. On the other hand, they found that on reducing the weight of charge 20 per cent, and using the cartridge of larger diameter, the round would not throw down the coal satisfactorily.Experiments with ""snubbing"" showed a similar improvement in quantity of lump coal, end the coal that was blasted rolled forward into the working place. however, in recent tests at another mine where the coal Lad different physical characteristics, snubbing did not always result in the coal rolling forward, on account of clinging to the ribs, and was not found to be an advantage. Therein the writers of this paper recommend that tests be made before deciding upon the adoption of snubbing in a particular mine."

Aug 1, 1925

By R. S. Olsen

Although aluminum is easily leached from calcined clay with boiling mineral acids, the presence of fines and slimes in the leached residue has hindered the application of acid leaching processes. A feed preparation method was, therefore, devised that provided a dense, smooth-surfaced, fine-grained clay. The important factors affecting feed quality were determined to be (1) crushing the raw clay to the size desired for the leaching process, (2) moistening the crushed clay with a fine mist of water while tumbling on a rotating disk, (3) drying the misted clay, and (4) calcining the dried clay at 750° C in a fluidized bed. Clay treated by this method was leached with HCI, and its residue was washed by water displacement in 4-ft-deep beds. Bed permeabilities on the order of 47 darcys or 4.6 x 10-7 cm2 were obtained with the leached residues.

Jan 1, 1983