Search Documents

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By Tomohide Takeyama, Yuki Yoshida, Masaki Kitazume

"Abstract A series of centrifuge model tests was conducted to investigate the failure pattern and stability of cement treated clay ground having an unsupported vertical slope. The model ground was subjected to monotonically increasing centrifugal acceleration until it failed due to the enhanced self-weight. The test results were compared with the numerical analyses in which the treated soil was simulated by the Smoothed Particle Hydrodynamics (SPH) method. In the simulation, the Dracker- Prager model is employed as the constitutive model. In order to simulate the brittle behavior of the cement treated soil, it is assumed that the unconfined strength is gradually reduced to a certain value which corresponds to the residual strength due to accumulated plastic strain. It was found that the simulation by using SPH method can express the brittle failure observed in the centrifuge model tests.IntroductionBecause of economical and environmental concerns it has become more difficult in recent years to obtain enough soil to construct reclaimed land for airports, electric power plants, manufacture plants and so on. On the other hand, it has become difficult to find and construct disposal sites for waste subsoil or dredged soil. These circumstances have encourage geotechnical engineers at present to use these poor quality materials as filling materials more than they were used one or two decades ago. Several soil admixture methods have been developed to improve their properties and to manufacture high quality fill materials.The deformation and strength characteristics of cement treated soils have been investigated in Japan, which have revealed that the treated soil is characterized by a brittle behavior with quite high compressive strength and quite small strain at failure, and the treated soil with relatively high strength shows tensile failure instead of shear failure. Regarding to evaluate the stability of structures adjacent to or buried in the treated ground, Kitazume (1998) and Kitazume et al. (2003) investigated the earth pressure of cement treated ground by the centrifuge model tests. And they emphasized that the failure pattern of the cement treated ground was much different from that of ordinary ground. After the Hyogoken- Nambu earthquake in 1995, many design codes for the seismic stability were revised in Japan, so that seismic stability must be evaluated more precisely. The dynamic earth pressure of ordinary grounds is usually calculated by a pseudo-static limit equilibrium method based on the Mononobe- Okabe’s method (Okabe, 1924; Mononobe and Matsuo, 1929). This calculation method is also applied to the cement treated ground, although its applicability has not been thoroughly clarified."

Jan 1, 2014

By Patrícia Freitas Rodrigues

Um comparativo entre dois métodos para determinação das temperaturas de transformação de fase, tendo como base análises de Calorimetria Diferencial de Varredura (DSC) em amostras de uma liga de NiTi equiatômica submetida a tratamentos térmicos para envelhecimento, foram utilizados neste trabalho. Sendo aplicado o método clássico comumente utilizado para análise desses resultados e o método utilizando da integral do pico de transformação de fase. Com base nas avaliações feitas, o método de integral por apresentar uma relação direta da fração de transformação demonstra-se mais eficaz para determinar o início e o fim da transformação por levar em consideração a forma do pico em função da trajetória de transformação.

Aug 8, 2018

By Hakan Gurgenli

Many coal seams have weak shale immediate roofs that cause ground control problems. Therefore, it is important to know the properties of these shales so that preventive measures can be developed in advance. However, it is sometimes hard to understand this rock type due to its unpredictable behavior. A good example of this situation is found in two shale coal mine roofs located in the Illinois coal basin (Herrin No. 6 seam). Although, these mines are located very close to each other, one of them has many roof falls, whereas the other has no measurable ground control problems. The aim of this paper is to explain why and how one shale roof behaves worse than the other. Laboratory tests, including point load strength index, slake durability index, moisture activity index, weatherability index, water content determination, swelling strain and x-ray diffraction tests were performed to analyze the shale properties. According to these analyses, some useful correlations were found between the engineering properties, moisture-sensitivity indices, and weathering properties. Finally, mine and support design considerations based on the test results were discussed and recommendations to prevent ground control problems were given.

Jan 1, 2006

By Arthur D. FitzGerald

EDC established an Environmental Review Framework in 1999. Throughout the early fall of 2001, the Corporation held public consultations across Canada to strengthen that framework, leading to a public release on November 15, 2001 of a report summarising the results of these consultations. Following this, the Corporation implemented strengthened environmental review requirements in the form of its Environmental Review Directive, in compliance with legislated amendments to Canada?s Export Development Act that went into effect on December 21, 2001. Over the past few years, there has been a global trend towards an increase in the social and environmental requirements of multilateral/bilateral financial institutions and export credit agencies. More recently, this activity has focussed on capturing institutions that have not yet adopted similar requirements and, more specifically, on developing a convergence of the requirements from institution to institution. This paper describes EDC?s new ERD and some of the initiatives that have taken place or are in process that are moving international financial institutions toward converging their environmental and social requirements for projects in the private sector.

May 1, 2002

By W. S. Sanner

Pyrolysis (destructive distillation) techniques developed at the Bureau of Mines to determine the yield and quality of the products from coal were used to convert municipal (household) and industrial refuse into potentially useful solids, liquids, and gases without adding to environmental pollution. The tests demonstrated that a ton of municipal refuse can be converted into 154 to 424 pounds of solid residue, 0.5 to 6 gallons of tar, 1 to 4 gallons of light oil, 97 to 133 gallons of liquor, 16 to 32 pounds of ammonium sulfate, and 7,380 to 18,058 cubic feet of gas. A ton of industrial refuse, consisting of paper, rags, and cardboard, can be converted to 618 to 838 pounds of residue, 1.5 to 3 gallons of light oil, 68 to 75 gallons of liquor, 12 to 23 pounds of ammonium sulfate, and 9,270 to 14,065 cubic feet of gas. The energy from the gas is more than sufficient to provide the heat for the pyrolysis.

Jan 1, 1970

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

Certain Molybdenum Resources in Indonesia Mineralogical and Processing Study

Sep 13, 2010

By K H. Esbensen

The Theory of Sampling (TOS) has contributed significantly to chemometrics by allowing data analysts to become more aware of total measurement uncertainty as total sampling error + total analytical error. This has allowed a new view on, for example, validation of multivariate data models and their performance. This keynote focuses mostly on the reverse perspective: how can chemometric multivariate data modelling be of help in an augmented sampling context? The basic principles of multivariate data analysis are presented and application examples are outlined from several areas in the geosciences to facilitate answers to the question posed, including a geochemical multivariate anomaly concept defined by a multivariate background model. Applications from geochemical prospecting, geochemical mapping, environmental chemistry and anthropogenic outlier recognition are outlined, as are the interdependent relationships between geostatistical modelling (variographics) of singular variables versus linear combinations of a multitude of variables, in chemometrics called scores. The potential synergy between chemometrics and TOS is far from exhausted at this time; much work remains.CITATION:Esbensen, K H, 2014. Theory of sampling in a multivariate perspective – what can chemometrics contribute?, in Proceedings Sampling 2014 , pp 7–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

Factual data about the sedimentation in the Newcastle Coal Measures are presented. Data concerning the total coal measure sequence (isopachs, sand/shale ratio, and total coal thickness variation), data about three coal seams (Borehole, Dudley, and Victoria Tunnel) and data about interseam conglomerate units are discussed.From this data conclusions are drawn about the coal measure environment. The western edge of the coal basin, the Lochinvar Dome, although a high feature, was apparently stable during coal measure time. Despite its height it apparently supplied little sediment to the basin.The northern and north-eastern edge, which was unstable, supplied most of the coarse detritus (including the conglomerates) to the basin. The conglomerates show patterns of fluvial origin but after a period of "normal" variations in pattern they become restricted to two parallel zones evidently tectonically controlled. Deposition of conglomerates is episodic and separated by periods of coal formation when deformation was apparently slight. Formation of each of the three seams considered followed a rather similar pattern- each show development of thick coal around the basin edge and poor thin coal in the "axial" region of the present synclinal structure.Evidence of ill situ formation of some areas of the seams is discussed and periodic deformation of the basin during coal measure time is postulated.The unusual character of this coal basin, in particular the very coarse units, is stressed, despite the presence of many "normal "coal basin features.

Jan 1, 1970

By J. Chai

In order to find the behavior of dewatered unconsolidated strata during the process of injecting water through a borehole, a new type of fiber Bragg grating (FBG) sensing system was successfully used for the real-time strain monitoring of unconsolidated strata during a water injection process for a dewatered unconsolidated strata of a coal mine. The unconsolidated strata water injection test was implemented through a borehole at a depth of +115.83 to +135.15m. The employed FBG strain monitoring system and ground water level observation system were installed at the depth in the unconsolidated strata where the water injection was conducted through two different boreholes. The water injection pressures in the test were 0.1, 0.2, 0.3MPa respectively, and the total water injection volume was 4226.84m3. The relationships between the water injection pressures, water injection volume and the strain change of the unconsolidated strata, the stress and strain conditions of the unconsolidated strata before and after water injection, were analyzed. This paper presents the results of these tests, and shows that the dewatering compression of the unconsolidated strata is reduced with increasing water injection pressures and water injection volumes. Comparing the stress-strain conditions before and after water injection, it is found that the stress of the water injection strata is in tension, which confirms the theory that the settlement of the thick unconsolidated strata is directly caused by the reduction of ground water levels. The high sensitivity and stability of the FBG monitoring system used was able to realize the real-time strain monitoring of the water injection process within a deep unconsolidated strata. This FBG monitoring system and the test results presented are very important for understanding further treatment of settlement in unconsolidated strata.

Jan 1, 2012

By H. Brindel

The paper point out the importance of a maintenance program at Toquepala, as to the effect that any changes in the above may have on the program and organization. The Southern Peru Copper Corporation carry out a training program in operation with a appropiate peruvian staff, as it has been established the basics for a sound, preventative maintenance and repair organization. In consecuence, this company decided to expand a two -fold program of training and maintenance so that the Peruvian personnel will not only be an aid to the Company but a national as set to Perú as well.

Aug 20, 1963

By J. L. Holman

The Bureau of Mines is conducting research to improve technology for the recovery of strategic and critical metals, such as cobalt, nickel, and chromium, that are lost in bulk and particulate superalloy-type scrap because it has not been possible to process mixed contaminated scrap efficiently. The research approach involves melting and casting mixed superalloy scrap into soluble anodes for electrodeposition of Ni-Co alloys by controlled-potential electrolysis. The initial experimental results described in this report are from electrolytic tests us-ing alloy anodes cast from elemental nickel, cobalt, and chromium, the main constituent metals of superalloys. Baseline data and operating parameters are necessary for Ni-Co and Ni-Co-Cr alloys before detailed experiments can be conducted on the more complex superalloy scrap. This basic research assessed the effects of cathode potential, S04:CI electrolyte ratio, electrolyte pH, stirring rate, deposition time, cathode current density, and chromium concentration on cathode current efficiency, alloy deposit composition, and deposition potential at a cell temperature of 55° C.

Jan 1, 1985

By M. C. Azar, W. B. Mason, G. L. Anderson

Eminent domain overview Eminent domain is the power of the Government or a municipality to take property for public use without the consent or acceptance of the owner. Typically, the agency taking the prop¬erty will make an offer, hoping the owner will immediately accept and allow work to begin. If a mutual resolution regard¬ing its value cannot be reached, how¬ever, the municipality will institute a condemnation action in court seeking possion of the property. This is when the problems begin. The power of the Government to take the subject property is limited by Federal and state constitu¬tional requirements to pay "just com¬pensation" for the property. The exact nature of an owner's prop¬erty has been the subject of much debate and discussion. It is generally under¬stood, though, that property is consid¬ered to be "every kind of right or inter¬est, capable of being enjoyed and recog¬nized as such, upon which it is practi¬cable to place a money value" (US vs. 53 114 Acres of Land). A taking, for condemnation purposes, is considered to occur whenever there is a substantial interference with the free use and enjoyment of the property. Rarely is the necessity for the taking ever challenged and more rarely is the taking ever successfully challenged. When a taking occurs, it is not only the fee owner who is entitled to compen¬sation. Every person holding an interest in the subject property will be recog¬nized. Thus, all persons who at the time of taking have a compensable interest in the property will be made parties to the case (Swanson vs. US). Minerals, like all other interests in land, are recognized as property rights, giving the owner the power to dispose of them as he or she sees fit. Thus, the only remaining considera¬tion is only "just compensation." Ex¬actly what "just compensation" is has been difficult to define. Generally, it is that amount of money that will "put the person in as good a position as the per¬son would have been in had the taking not occurred." The owner must not be forced to sacrifice or suffer by receiving less than full and fair value for the prop¬erty. Every element that effects the value of the land and that would influence a purchaser must be evaluated. Courts have employed a variety of techniques to determine just compensa¬tion but have generally relied on market value as the standard for measuring compensation to the owner. The deter¬mination of market value is based on sales, income, costs, and use. These factors have been employed in various ways but can be summed up as: -The highest estimated monetary price the property will bring if exposed for sale in the open market with a reason¬able amount of time allowed to find a purchaser who is buying with knowl¬edge of all the uses and purposes to which it is adapted and for which it is capable of being used. • The amount the property would bring if it were offered for sale by one who desired, but was not obliged, to sell, and was bought by one who was willing, but not obliged to buy. • What the property would bring in the hands of a prudent seller, at liberty to fix the time and conditions of sale. • What the property would sell for in negotiations resulting in sale between an owner willing, but not obliged to sell, and a buyer willing, but not obliged to buy. • What the property would be rea¬sonably worth on the market for a cash price, allowing a reasonable time to affect a sale. (Michigan Standard Jury Instructions). Special consideration regarding mar¬ket value is given when the taking is only partial, rather than complete. An example of this partial taking is when a state highway cuts across the northern half of a parcel of property, leaving the rest behind for the owner. A variety of problems can be immediately seen. In a partial taking, the owner is permitted to recover not only for the property taken, but also for any loss in the value of the remaining property. The measure of compensation for partial taking purposes is generally the difference between the market value of the entire parcel before the taking, and the market value of what is left of the parcel after the taking (Michigan Stan¬dard Jury Instructions). Determining the partial taking value for mineral bear¬ing lands is the difficult issue.

Jan 1, 1989

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crashed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summarizes of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling a t the same group of quarries. OBJECT OF STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By P. H. Williams, D. J. Morris

The co-disposal of coarse and fine coal wastes by combined pumping through a pipeline to subaerial deposition was pioneered in Australia in 1990 by Jeebropilly colliery in Queensland. Significant segregation of fines is found to occur in its co-disposal delta, leading to the formation of distinct mainly coarse upper and fine-dominated lower segments; the upper delta drains rapidly and is able to support traffic on its surface immediately after deposition. An existing theory of subaerial deposition, originally developed for mine tailings alone and later extended to trial co-disposal, is shown to apply also to the upper segment of the full-scale Jeebropilly delta

Jun 19, 1905

By V. B. Dale

This report is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits in Gila, Yavapai, and Mohave Counties, Ariz. Many of the descriptions are taken from the reports of previous examinations by Bureau of Mines engineers, and from Defense Minerals Exploration Administration files. Where a previous examination had been made, and an inquiry disclosed that little or no work had been done since that time, pertinent information from the report was used in this paper with acknowledgment of the source. However, the majority of the descriptions is from field examinations by the author. In the past 3 years (July 1956-May 1959) only necessary annual assessment work was conducted on nearly all the properties described in this paper. There was no active mining on any of the properties examined.

Jan 1, 1961

By P. C. Schutte

Ergonomics is the scientific discipline concerned with the understanding of interactions among humans and other elements of a system, and the profession that applies theory, principles, data and methods to design in order to optimize human well-being and overall system performance. Despite the fact that the application of ergonomics principles can make a major contribution to the management of significant occupational safety and health risks, ergonomics is currently applied on a limited scale in the South African mining industry. The objective of this paper is to provide a perspective of ergonomics, the main aim being to create a point of departure for the development of strategic objectives to enhance existing health and safety initiatives through the application of sound ergonomics principles. Two of the major consequences of poor ergonomics, namely work-related musculoskeletal disorders and worker fatigue, and possible means of introducing ergonomics into the South African mining industry, are discussed.

Jan 1, 2005

By M. R. Saharan

A brief overview of rockburst control measures is presented. The paper then elaborates on one key rockburst control measure, which is known as destress blasting. A historical background of the technique is presented in order to understand different aspects of its field application. The publication enumerates key aspects of the technique as being used in practice in South Africa and North America. The paper also presents an analysis of three case studies in order to demonstrate difficulties associated with the field application of distress blasting in hard rock mines.

Jan 1, 2006

By Faruk Oksuz, Clay Haynes, Miguel Sanchez, Patrick Finn, Roger J. Maurer

The Milwaukee Metropolitan Sewerage District’s (MMSD)’s challenges of basement flooding and wet weather sewer overflows are being creatively addressed with the Northwest Side Relief Sewer tunnel. The $132 million, 20-foot diameter, and37,740 feet long conveyance and storage tunnel excavation in dolomite at depths reaching 165 feet below ground surface has been successfully completed within13 months in April 2004. This paper includes Owner’s perspective on the overall project, and the design and construction details by the Designer and the Contractor. The project contract documents included a comprehensive Geotechnical Data Report and the Geotechnical Baseline Report.

Jan 1, 2005