Search Documents

The U.S. Bureau of Mines has been concerned for many years with the general problems of underground coal mining and the particular problems due to the methane content of the coal. The Bureau and others have worked diligently to improve the health and safety conditions for underground coal miners. It has been recognized for many years that the methane in coal would have some value if it could he recovered and used, Also its removal before coal mining began or during the mining cycle itself would make mining safer and more economic due to a potential saving in ventilation costs. The work covered in this report was carried out to review methods of removing methane from active and inactive regions of operating coal mines and to determine how the methane could be concentrated and utilized economically.

Jan 1, 1975

By Milton C. Graves, Marcos Zentilli

"Gold has been reported from most geological environments in Nova Scotia; however, virtually all production (circa 2,000, 000 troy ounces; circa 60 tonnes) has come from that part of the province to the south of the Glooscap Fault which is underlain by Lower Paleozoic rocks of the Meguma Group. Over fifty concordant sets of quartz-carbonate-arsenopyrite veins have seen production. The host rocks are greenschist-grade equivalents of Cambro-Ordovician flyschoid quartz wackes and shales folded and metamorphosed during the Devonian Acadian Orogeny. The veins were emplaced under conditions of greenschist-grade regional metamorphism and under the same conditions of tectonic stress that later resulted in the regional folds and penetrative, axial-plane slaty cleavage. Rapid filling of hydraulic fractures caused by excess metamorphic pore fluid pressure under Acadian tectonic stress conditions can account for the geometry and paragenesis of these veins.The ultimate source for gold deposits in most greenschist-grade domains remains in doubt, but these domains seem to have had ample gold within them available for mobilization. The work done, to date, on the gold geology of Nova Scotia suggests that regional greenschist metamorphism was an effective mobilizer and a potential concentrator of Au, As, W, Fe and S from these vast reservoirs.In rocks of pre-Acadian age north of the Glooscap Fault, gold occurs as an important accessory in volcanogenic massive sulphide ore, as a minor constituent in other types of basemetal concentrations and in one small concordant group of quartz veins.The post-Acadian metallogenetic domain, which overlies and overprints the two older domains, contains small amounts of gold in many mineralizing environments. Veins, with stibnite and gold, cross-cut crystalline rocks. Disseminated gold is present in basal conglomerates of post-tectonic molasse. Gold has been a by-product of Mississippi Valley-type Pb-Zn-Ba-Sr deposits in Lower Carboniferous sedimentary rocks and has been reported with Pb-Zn-Ba-F in veins which cross-cut Lower Carboniferous and older rocks. Small post-glacial placers have also seen minor production."

Jan 1, 1982

By Emma Arakelova

?2?2 (98 %) vapour passed through a reactor at 25Pa where a Zn? target was placed at 273K- 373?. Experiments were carried out on a flow- type vacuum device. ?2?2 decomposition on Zn? surface accompanied by formation of a Zn-containing volatile complex which transferred to the gas phase, and Zn? deposited on a substrate at condensation. As the substrate, five sequentially located quartz cylinders were used at 293K- 423 K (?n). Decomposition of the Zn-containing complex on quartz substrates carried out as a first- order reaction. ?The complex decomposition constant (??) increased with the substrate temperature (?n=293 K, ??=7.05 sec-1;?n = 373 K, ?? = 87 sec-1;?n = 423 K, ?? =158 sec-1). ?The complex decomposition constant did not practically vary when the target temperature increased; the complex formation rate increased slightly.

Jan 1, 2006

By Jorge Oviedo

La planta de lixiviación, extracción por solventes y electrodeposición (L-SX-EW) de Southern Perú es una operación hidrometalúrgica dedicada a la lixiviación ácido – bacteriana de los botaderos de mineral de baja ley de la Mina Toquepala, para la producción de cobre catódico de la más alta pureza. En ese sentido, el presente trabajo describe la evolución del sistema de control y supervisión de esta planta minera en Cuajone. Para ello, dicha planta debe tener una actualización constante de sus sistemas de control y ser capaz de cambiar con la velocidad a la que avanza la tecnología de Control de Procesos. Asimismo, debe contar con personal calificado que permita el desarrollo y modernización de los sistemas sea continuo y no dependa solo de expansiones y ampliaciones ejecutadas por especialistas externos. De forma que este software de supervisión, no solamente considera la capacidad de operar la planta, si no debe ser una ayuda tanto para el operador como para brindar información en la correcta toma de decisiones.

Aug 25, 2002

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

Base metal sulphide mineralisation on the northern end of Great Barrier Island is spatially associated with hypabyssal intermediate to acidic intrusives, in transgressive structures in indurated, complexly deformed greywackes and argillites. Copper predominates in the mineralisation, with minor accompanying lead and zinc and also some gold and silver. However, in some cases lead or zinc may be the dominant constituent. The mineralisation is generally characterised by only narrow envelopes of weak alteration (propyliticassemblages dominated by chlorite and epidote) and with only minor amounts of quartz accompanying the sulphides, which form a cement in zones of hydraulic fracturing. There are two distinct structural settings to the mineralisation: at MinerÆs Head, in a structurally complex situation in a shell-like zone of crackling in hornfelsed greywacke, in association with both north- and east-striking fractures and rubble breccias associated with the apical part of a large intrusive; and in very narrow, but very strike-persistent, 1inear steeply-dipping fracture zones, exposed on the north coast and inland areas near Tataweka.

Jan 1, 1984

These proceedings consist of papers presented at Bureau of Mines Technology Transfer Seminars in August 1983 for the purpose of disseminating recent advances in mining technology in the area of large mobile surface mining equipment safety and health. The Bureau of Mines conducts several of these seminars each year in order to bring the latest results of Bureau research to the attention of the mining industry as quickly as possible.

Jan 1, 1983

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By B. van Beek, T. Goff, P. Gebski, P. Szyplinski, W. L. Ying

"Monitoring the refractory lining integrity is essential to assure the safety of the operators and to determine the remaining campaign life of a furnace. Early detection of refractory lining degradation is essential to avoid sudden furnace failures and prevent unscheduled shutdowns. In the mid-1990s a stress wave propagation technique was developed and since then it has been utilized by Hatch Non-Destructive Testing (NDT) Group to evaluate furnace linings. For the last 17 years the AU-E technique evolved in terms of hardware, software and signal acquisition and interpretation. Most importantly, based on more than a decade of commercial applications, an extensive database of various failure modes, refractory deterioration trends and material properties has been created. This knowledge base is an integral part of AU-E which progressed from a NDT technique towards a comprehensive approach for furnace condition monitoring. All of the improvements introduced over the last several years have greatly improved the accuracy of the measurements. The data analysis process has also become more time efficient making the critical results available to the furnace operators in a more timely manner. Today the AU-E technology is used on a variety of process vessels in non-ferrous, glass, chemical and iron and steel industries.In this paper we are reviewing the available techniques for furnace refractory lining measurement and discussing the pros and cons of each method. The need for continuous improvement and development of new techniques for refractory monitoring is also emphasized. Finally, we are presenting a number of case studies and comparisons between the physical verifications and the AU-E measurements."

Jan 1, 2015

By William O. Vanderburg

This paper 3/gives the results of a reconnaissance of mining districts in Clark County, Nev., made from November 18 to December 22, 1936, and from February 9 to March 8, 1937-in all, 63 days. While the field work Was being done, virtually all of the mining districts in the county were visited and many data on active and inactive properties were obtained. The report covers the locations of the various mining districts, the nature of the deposits, information on past operations, current activity, and general data likely to be useful to operators, investors, and others interested in mining. The geology of the deposits is discussed only briefly. The principal metal-mining districts in the county are Goodsprings, Eldorado, and Searchlight. The zinc-lead ores of Goodsprings have been the most important economically, followed by the gold-silver ores of Eldorado and Searchlight. In the industrial-mineral field, gypsum, limestone, silica sand, and borates are the principal products. Metal mining in the county is characterized by numerous small operations and the ores are either milled locally or shipped to distant smelters.

Jan 1, 1937

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

A novel, low-pressure adaptation of Praxair?s coherent jet technology utilizing CoJet lances was developed for application at Inco&apos;s Copper Cliff Smelter where oxygen is available in large tonnage quantities but only at relatively low supply pressures (< 193 kPa header pressure). The project objectives were to evaluate the effect of coherent jet technology on controlling oxygen lance accretion (?horn?) formation and to increase oxygen efficiency in the Inco Oxygen Top-Blowing Nitrogen Bottom Stirring (TBBS) MK Reactor used for converting nickel- contaminated chalcocite to semi-blister copper. This paper describes the development and subsequent implementation and testing of two CoJet lances in this application.

Jan 1, 2005

By H. Copur

Experimental studies for quantification of force and brittleness indices relevant to rock cutting performance are presented. A simple interpretation method is developed, which quantifies the force-penetration response obtained from indentation tests. Basic parameters of the quantification are force increment and decrementrates, force increment and decrement periods, and number of increment and decrement data points. Blocks of eleven different rock samples were collected from different operating mines in Turkey and subjected to indentation tests to calculate the indices. The samples included harzburgite, serpentinite, trona, limestone, claystone, two different sandstone samples, siltstone and three different chromite ore samples. The concept was validated by a set of full-scale linear cutting tests using a conical cutter for measuring the cutting performance in relieved and unrelieved conditions, i.e. cutter forces, specific energy, size distribution of rock cuttings. The rock cuttings were sieved to determine coarseness index, indicates coarse chip generation characteristics, and size distribution. The force index is moderately correlated with the cutting performance and mechanical properties of the rocks, and poorly correlated with the coarseness index and size distribution of cuttings. A general and moderate trend is observed between the brittleness index and the coarseness index, cutting performance for unrelieved cutting conditions and mechanical properties of the rocks. However, additional data is required to fill the data gaps and to potentially establish relationship between the brittleness index and all other parameters.

Jan 1, 2003

By R Long

The founder of social psychology is sometimes identified as Kurt Lewin. In a 1947 article, Kurt Lewin coined the term ‘group dynamics’. He described this notion as the way that groups and individuals act and react to changing circumstances. Lewin theorised that when a group is established it becomes a unified system with unique dynamics that cannot be understood by evaluating members individually. The discipline of social psychology really emerged out of World War II and tackled questions associated with human judgement and decision-making by the Nazis. For a comprehensive look at the development of social psychology look at Abelson, Frey and Gregg (2004).Social psychology is concerned with the way social arrangements affect human judgement and decision-making. What the author has done is apply the knowledge of this new discipline to an understanding of risk, safety and leadership. This paper will explain some of the developments in social psychology, such as the discovery of the bystander effect, Groupthink, bounded rationality, heuristics, risk homeostasis and the Milgram effect.The social psychology of risk tackles the way decisions are made about risk in their social context. Unless organisations understand that decision-making is socially conditioned, they are unlikely to be able to tackle the complexities of culture change or the development of risk maturity.The paper will offer a new understanding of why people do what they do, how risk makes sense and why a ‘dumb down’ approach to safety is dangerous. A model will also be presented that shows the pathway to risk maturity.CITATION:Long, R, 2016. The social psychology of risk, safety and leadership maturity, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 31–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By B. J. Arnold, N. Terblanche

The features of the ‘Turbo’ froth flotation column will be discussed, including the double aeration system that improves flotation yield while not sacrificing grade, the internal launder system, and the unique feed/tailings sump that evens out flow to the flotation column preventing upset conditions. Results from various test programs and installations will be presented.

Jan 1, 2001

By M. Jessop, V. O. Kofoed, R. Blanchard, A. Hughes

Willowstick has successfully employed a new Seismic Acoustic Resonance (SAR) method to improve seepage characterization through, beneath, and around dams. SAR is a passive seismic method that detects zones of higher permeability in the foundation and fill materials of a dam. Just as the ocean has tides, the earth’s crust experiences daily “Earth Tides” and is constantly in motion. Continual motion produces resonance signals that can be measured, interpreted, and modeled to identify zones of higher permeability within a dam and its foundation. The SAR results are analyzed in conjunction with the traditional Willowstick Method to better characterize seepage flow paths and patterns trough, beneath, or around a dam in three dimensions. When both methodologies, which use entirely different scientific principles, identify the same anomalous feature, a higher degree of confidence is gained in the results of the investigation. Willowstick has effectively utilized the SAR method on many successful dam seepage investigations. The two geophysical techniques when used in parallel have yielded complimentary results, with both methods providing beneficial information about seepage locations. This paper will detail seepage flow paths identified using both Willowstick and SAR methods for two case study tailings dams in Canada and the United States.

Feb 1, 2023

By AIME AIME

EDWIN W. KEMMERER, professor of international finance at Princeton, in a speech before a banking conference at Urbana, Ill., on Nov. 26, stated that the increase in the store of gold held by the United States is not so alarming as it appears on the surface. Excerpts from his address, as reported by The New York Times, follow: "It is significant . . . that the value of gold as expressed in its purchasing power in the United States during the last half-dozen years has been higher than at any other equivalent period since our records began 140 years ago. Our so-called 59-cent dollar today buys about 25 per cent more goods at wholesale than did our old dollar in the prosperous year 1926, and an ounce of gold will now buy considerably more than twice what it did then. This present high value of gold is one reason for its recent large production.

Jan 1, 1941

By R. M. Santmyers

The chief compounds of boron are borax and boric acid, both of which have important applications in industry. At present the United States furnishes more than half of the world&apos;s requirements of borate materials, practically all from California. Nearly the entire production of borax in this country is under the control of four companies: The American Potash and Chemical Corporation, the Pacific Coast Borax Co., the West End Chemical Co., and the Western Borax Co.

Jan 1, 1931

By J. Kruttschnitt

This paper, describing the mining operations at Mount Isa Mines, is one of a series covering mining methods and costs being published by the United States Bureau of Mines. The Mount Isa property has been in operation since June 1931; during this period operations have changed from the production and treatment of carbonate ores to the mining, milling, and smelting of sulphide ores. This change involved revision of ore-extraction methods. Stoping methods have been designed to apply to parallel lodes ranging from 10 to over 100 feet in width and dipping at 50° to 60°. The hardness and strength of the ore and enclosing wall rocks, together with the strength and thickness of the country rock between lodes, have permitted the selection of a sublevel stoping method for mining the sulphide ores.

Jan 1, 1937

The Canadian concept for nuclear fuel waste disposal is being assessed by AECL Research in a series of experiments at its Underground Research Laboratory (URL) near Lac du Bonnet. Manitoba, Canada. As pan of this research, the Mine-by Experiment has been designed to obtain information on rock mass behavior, the development of an excavation-induced damage zone and failure mechanisms around a circular bored tunnel. An iterative design approach was used to effectively reconcile the experiment objectives and construction logistics. This paper discusses the design considerations and construction methodology adopted on the project.

Jan 1, 1991