Search Documents

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

By A. Fredriksson, R. Christiansson, I. Staub

A theoretical model based on DFN models and 2D DEM numerical modelling has been developed for evaluating the rock mass mechanical properties. The description of the methodology is non-site related and can be applied in any site for this type of characterisation. The methodology was developed in the frame of the Site Investigation programmes for a Deep Repository for spent fuel in Sweden, and validated on sets of data coming from the Äspö Hard Rock Laboratory. Un modèle théorique base sur des modèles probabilistiques de réseaux de fractures et sur un modèle numérique DEM 2D a été développé dans le but de déterminer les propriétés mécaniques de la masse rocheuse. La méthodologie développée peut être appliquée à tout type de site pour ce genre de caractérisation. Le modèle a été élaboré dans le cadre des programmes de recherche d’un site d’enfouissement des déchets nucléaires en Suède, et validé par une application au laboratoire de recherche souterrain à Äspö. Ausgehend von DFN-Modellen und 2D DEM numerischen Modellierungen wurde ein theoretisches Modell für die Auswertung von mechanischen Eigenschaften von Fels entwickelt. Die Methodikbeschreibung ist nicht standortspecifisch sondern kan überall für diesen Typ von Standordkarakteriserung angewendet werden. Die Methodik wurde in Schweden im Rahmen der Standortuntersuchungsprogramme für die Endlagerung von verbrauchten Brennelementen entwickelt und ist mit Hilfe von Daten des Äspö Hard Rock Laboratory validiert worden

Jan 1, 2003

By Howard P. Hamlin

This Bureau of Mines report is concerned with the testing procedures for evaluating clays, shales, and slates for lightweight aggregates using the rotary-kiln method of production. To meet the increasing demand for light-weight concrete, rapid, accurate methods for appraising raw materials for light-weight aggregate are needed. Preliminary tests were made on samples of clay, shale, and slate, using laboratory equipment, and the data were used to establish operating conditions for pilot-plant-size rotary-kiln tests. Lightweight concrete was made from the processed aggregates and the properties determined. The results show that the laboratory data can be used to guide rotary-kiln testing, and, with the exception of sampling, a complete appraisal of a raw material for lightweight aggregate concrete can be made in 3 days by the methods described in this report.

Jan 1, 1962

By Erin Legault Seguin, Mike Rylatt, Curtis Mohns

"With energy costs increasing and ore grades diminishing, the role of pre-concentration in hard rock mining operations has been gaining greater interest. To maximize energy conservation, the pre-concentration process should be conducted at as coarse a crush size as possible while minimizing losses of pay metals. Dense medium separation (DMS) is a robust process that can be conducted at particle sizes as coarse as 300 mm and as fine as 500 µm with high separation efficiency, depending on liberation characteristics of the value minerals. The DMS process involves three steps: feed preparation, dense medium separation, and ferrous-based media recovery. This paper discusses each of these processing steps, but focus will be given to the dense medium separation stage. Various types of DMS equipment are reviewed. Pilot plant campaign case studies conducted at the SGS Lakefield site are presented, which have included a variety of mineral systems such as spodumene, sulphide-bearing gold ores, and complex sulphide ores. These case studies demonstrate that for amenable ores, mass rejection of 20-60% is possible while maintaining recoveries of greater than 90% in most cases.IntroductionPre-concentration is a process of rejecting mass of gangue while ensuring recovery of valuable minerals prior to more intensive, downstream processing. Pre-concentration has been practiced in industry for many years, and is gaining greater interest as the industry copes with processing lower grade, more difficult ores, typically requiring finer grind sizes and higher energy costs."

Jan 1, 2016

By AJ Rorke, JD Botes

Presplit blasting in strip mines is aimed at creating a safer wall to work under during the coaling operations. Good quality presplits are also necessary for effective throw blasting and drainage of the blast block. A less obvious but important function is full coal recovery. Optimum Colliery has been experiencing rock freezing against the presplit highwalls. The rock formed in patches along the highwall and trapped coal beneath it. The material that was &ozen comprised the rock between the back row of holes and the presplit and was often up to 3 m thick (the stand off distance between the back line and the presplit). The cozen rock formed predominantly along the bottom halfor bottom two thirds of the highwall. Along the top portion of the highwall, the presplit crack was usually well formed with visible barrels. This problem, or similar variations of it, is common on many South African strip-mine operations. Investigative work was carried out at Optimum Colliery to correct the problem. This paper presents the information and measurements that were made and discusses the solutions that have been applied to solve the problem. It was found that there were two independent causes for the tiozen material, with each contributing more or less to the frozen rock along the highwall. It was found that the presplit was not forming properly in places, especially closer to the bottom of the highwalls. The reasons and the solutions are presented. The second cause was found to be associated with reduced detonation velocity in the back line holes coupled with low confinement from long delay periods. Emulsion explosive that is sensitised with air bubbles was found to be prone to this phenomenon near the back of high-energy blasts. A change in the explosive formulation in the back-line holes, together with reduced delays in the back line, has resulted in significant improvements. The details are presented in this paper.

Jan 1, 2000

By L Matthews, D O’Dea, P C Hayes, J Manuel, B Monaghan, T Honeyands, D Pinson, J Leedham

Many different approaches have been used in the past to characterise iron ore sinter mineralogy to predict sinter quality and elucidate the impacts of iron ore characteristics and process variables on the mechanisms of sintering. Characterisation techniques include optical image analysis and point counting, X-ray diffraction and scanning electron microscopy. Each technique has its advantages and disadvantages depending on the objectives of the measurement. It is generally acknowledged that silicoferrite of calcium and aluminium (SFCA) is very important to the quality of the sinter produced; however, strict definitions of the phases and textures of SFCA are not generally agreed. This paper summarises the state-of-the-art in sinter characterisation applied in Australia by both academics and industrial researchers. The results from various techniques are compared and the relationships between the measurement results are discussed.CITATION:Honeyands, T, Manuel, J, Matthews, L, O’Dea, D, Pinson, D, Leedham, J, Monaghan, B, Li, H, Chen, J, Hayes, P C, Donskoi, E and Pownceby, M I, 2017. Characterising the mineralogy of iron ore sinters – state-of-the-art in Australia, in Proceedings Iron Ore 2017, pp 49–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By W. J. D. Stone

In 1960, Magnetics International Ltd. undertook the development of the Jones High Intensity Wet Magnetic Separator in the Americas. Magnetics International had a number of possible applications in its own projects plus the intention of developing the equipment for sale to others. It was soon recognized that no matter how innovative a piece of mineral separation equipment may be, it takes many years and much finance before it is finally accepted for large scale use. For this reason, many good ideas die in their infancy. One of the chief reasons for such a time lag between conception and large scale implementation is the usual lack of finance to construct and put into operation a large demonstration unit. Even with a large unit for demonstration, the first major user usually requires a guarantee that is not normal in accepted separation equipment. Such problems are also normally accompanied by major design changes from the first conception.

Jan 1, 1971

By M. Jele

? Sulphuric acid plant in umbogintwini. ? Double absorption plant, capacity of 550MTPD. ? Build by simon curve during the year 1973. ? Side stream plants such as: ? Liquid SO2 Plant, ? Liquid SO3 and ? Oleum plant

Jan 1, 2009

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971

By Thomas C. Wilder

Jan 1, 1965

By Stephen C. Tadolini, Dennis R. Dolinar

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that are easy to handle/install under temporary or previously supported roof.

By C. Pieper, J. B. Pateiro Fernandez, S. Möllerherm

"Since the United Nations conference on "environment and development" in Rio de Janeiro in 1992, the term "sustainable development" or short "sustainability" is used more and more in social-political discussions. Agenda 21 calls on the countries on national level as well as governmental and non-governmental organisations on international level to develop a concept of sustainability indicators to measure the progress towards sustainability. This paper deals with the development of an evaluation system for sustainability in the minerals extraction. By their application, aspects of sustainable development in the raw minerals industry are to be systematically conceived and assessed. This project has been carried out on behalf of the German Federal Ministry of Economics and Labour."

Jan 1, 2005

Project cost control procedures and computer systems have enjoyed a successful and simple relationship over the past decade, thanks primarily to the proliferation of portable computers or PC's. Prior to the introduction of this technology, project control was largely a manual and somewhat onerous task of historical data compilations, with little time available for dynamic forecasting, staged planning, or pre-emptive cost control. Automated systems developed during this era were resident on "Heavy Iron" or mainframe computers and were expensive to maintain and operate. Use of these early systems was limited to large engineering, construction, and industrial concerns with the economies of scale and funding required for their successful application. Systems were either designed for critical path analysis or task scheduling, but rarely integrated with the other, much less cost control.

Jan 1, 1990

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application for geological structures, has been criticized for reliance on subjective interpretations. The Mine Safety & Health Administration’s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and fault zones that were parallel with projected lineaments. The Roof Control Division’s successful identification of lineaments associated with roof falls and highwall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions will allow mine operators to obviate safety concerns that might otherwise adversely affect miner health and safety.

Jan 1, 2002

Situated in the Greymouth Coalfield, the Mt Davy Block contains a significant resource of high quality bituminous coal suitable for use in metallurgical coking coal blends. The coal, which is all low sulphur, is seen as a complementary deposit to export coking coal at Stockton Mine.   Previous drilling by State Coal Mines (1948 - 1953) and Japanese interests (1970's) have been supplemented by Coal New Zealand drilling (1992 - 1993) and surface mapping. A mining feasibility study was completed in late 1993 and approval gained for the driveage of an exploratory tunnel to the target seam.   Following construction of surface facilities, tunnel driveage on a 1:5 decline commenced from Rewanui in May 1995 and to date about half the required length has been driven. When the seam is intersected a comprehensive geotechnical testing programme will be undertaken to assess the in-situ mining conditions. It is expected that the results will confirm the assumptions made in the feasibility study.   The Mt Davy Mine, at depths of 500 - 700 metres, will be the deepest underground coal mine ever inNew Zealand and in-situ stresses (orientation and magnitude) will be important considerations for mining engineering. The coal has a high gas content and suitable techniques for gas control and prevention/mitigation of coal outbursts will be necessary.   Mine development is scheduled to commence in mid 1998 and an annual production level of 500 000 tonnes is forecast. The coal seams will be developed by continuous miner and coal extraction will be by hydraulic monitor. Coal will be pumped to the surface and from Rewanui transported five kilometres to Dunollie either by truck or slurry pipeline. At Dunollie a coal dewatering plant, coal stockpile and rail loadout will be constructed.

Jan 1, 1996

By S. Jayson Ripke, Shane Hoff

Cleveland-Cliffs’ Northshore Mining Company operates a magnetic iron ore (taconite) concentrator and pelletizer in Silver Bay, MN. These are two recent cost reduction projects: 1. Rougher Magnetic Separators were upgraded throughout the concentrator; throughput and recovery were simultaneously improved. 2. Green Ball Roll Screens on one agglomeration circuit were upgraded from 3.5-inch to 2.5-inch rolls. Throughput improved by 24% from 62 to 77 LTPH. Green ball size distribution improved as an added benefit.

Jan 1, 2005

By D. Christofferson

This final report documents the cooperative efforts of the Engineered Systems Division and the Mining Equipment Division of FMC Corporation during performance of Bureau of Mines Contract H0252091. Improved operator compartments incorporating overhead canopies, logical arrangements of controls, and design features offering greater operator comfort were developed and retrofitted to the FMC 320A roof bolter and 6L shuttle care The vehicles were evaluated in underground operations at separate mine sites. The successful evaluation has resulted in incorporation of the designs as standard features of the 320A roof bolter, and the 5L, 6L, and 10L shuttle cars.

Jan 1, 1978

By J. E. Scott, L. M. Heaman, R. A. Creaser, G. S. Salazar

"Schaft Creek is a calc-alkaline porphyry Cu-Mo-(Au) deposit located in northwestern British Columbia. The deposit formed in a volcanic arc setting, likely on a back-arc rifted continental fragment. It is hosted by Late Triassic basaltic to andesitic volcanic rocks of the Stuhini Group (Stikine Terrane), and is associated with porphyritic granodiorite dikes emanating from the nearby Hickman batholith. The age of the Hickman batholith is approximately constrained here by a composite U-Pb zircon date of 222.1 ± 9.6 Ma, which is in broad agreement with a well-constrained age for mineralization at Schaft Creek of 222.0 ± 0.8 Ma (Re-Os molybdenite). The deposit is in most respects typical of calc-alkaline porphyry systems, but displays silica-poor sericite-chlorite alteration in mafic country rocks in place of classic phyllic altera¬tion. The deposit comprises three distinct, but related, zones: the northern Paramount zone, the Main zone, and the West Breccia zone. Two phases of mineralization are observed. The first phase occurs as hydro-thermal veins and breccias, and minor disseminations. It consists of bornite, chalcopyrite, molybdenite, and pyrite with potassic and sericite-chlorite alteration. The second phase is minor and consists of veins of molybdenite ± specularite, as well as Cu-Pb-Zn sulfide veins without any significant corresponding alteration. Extensive structural modification has affected the deposit both during and after its formation.Schaft Creek est un gîte porphyrique de Cu-Mo-(Au) calco-alkalin situé dans le nord-ouest de la Colombie Britannique. Ce gîte s’est formé dans environnement d’arc volcanique, probablement situé sur un fragment continental bordé par un bassin d’arrière-arc. Le gîte est encaissé par les roches volcaniques basaltiques à andésitiques du Groupe de Stuhini (Terrane de Stikine) d’âge Triasique tardif, et est associé à des dykes de granodiorite porphyrique provenant du batholithe de Hickman avoisinant. L’âge du batholithe de Hickman est estimé par un âge U-Pb composite sur zircon de 222.1 ± 9.6 Ma, lequel est grossièrement en accord avec l’âge de la minéralisation de Schaft Creek, estimé a 222.0 ± 0.8 Ma (Re-Os sur molybdénite).Ce gisement, bien qu’à plusieurs égards typique des systèmes porphyriques calco-alcalins, présente une altération en séricite-chlorite pauvre en silice dans l’encaissant mafique a la place de l’altération phyllique classique. Ce gîte comprend trois zones distinctes bien que connexes : la zone Paramount au Nord, la zone Principale et la zone West Breccia. Deux phases de minéralisation sont observées. La première phase se présente sous forme de veines et de brèches hydrothermales ainsi qu’en disséminations mineures et consiste en bornite, en chalcopyrite, en molybdénite et en pyrite avec une altération potassique et en séricite-chlorite. La seconde phase est mineure et consiste en veines de molybdénite ± spécularite ainsi qu’en veines de sulfures de Cu-Pb-Zn sans association à une altération particulière. Le gisement a été profondément modifié par la déformation a la fois durant et après sa formation."

Jan 1, 2008

By Harry Schnabel

A 6200 m² cement deep soil mixed (CDSM) wall was constructed for an addition to the Museum of Fine Arts in Boston, Massachusetts. The addition was located along the east side of the existing museum within an existing courtyard and in the area of a recently demolished structure. The basement for the new addition extended up to 9.1 m below the floor slabs of the adjacent buildings. The adjacent buildings are supported on a variety of foundations including; shallow spread footings on alluvial sand deposits, low capacity piles bearing in the alluvial sands and Boston blue clay, and caissons bearing on the alluvial sands and clay. Groundwater was less than one meter below the top of the CDSM wall. The new addition was founded on shallow foundations in the desiccated crust of the Boston Blue Clay. The CDSM wall was selected as the most economical means to control deep seated ground movements, limit movements of adjacent structures, and inhibit groundwater flow into the excavation. Braces and a continuous wale were used to support the CDSM wall where it was located adjacent to structures. Tiebacks were used where there were no structures. Other geotechnical construction at the site included: ? Jet grouting (JG) to improve the ground and provide an impervious subgrade layer at the west end of the addition, ? Concrete pier underpinning was used to support an existing structure on the west end of the site, and ? A secant pile wall using alternating drilled shafts and jet grout columns was used for earth support and a barrier to groundwater flow to allow for the installation of a storage tank at the south end of the site. Inclinometers, total station surveying, vibrating wire strain gauges on the braces and wales and load cells on the tiebacks were used to monitor performance of the excavation support system. The excavation support system performed better than required limiting lateral movements of the adjacent structures to less than 13 mm and vertical settlement to less than 8 mm. No settlements or movement were detected during the construction of the wall. Lateral movement of the CDSM wall was typically below 15 mm with the maximum movement occurring near subgrade.

Jan 1, 2011

By Raymond B. Ladoo

The uses for which ground talcs are suited closely depend upon their physical and chemical properties , but , in spite of this fact , little scientific investigation has been made in order to devise quick and accurate tests for the determination of these properties . The chemical properties of talc are inherent and may not be altered or modified except by selective mining or by chemical processes not practical in the present status of the industry . However , the determination of chemical properties is not so important , for most uses , as of physical properties , although sometimes certain chemical characteristics are perhaps unduly insisted upon by chemists in some industries . Physical properties are dependent both upon mineralogical characteristics and upon methods of grinding and sizing and may thus be partly changed or modified by changes in practice . There is so little known of the chemistry and physics of the various processes in which talc is used that the purchase and sale of talc is governed more by rule- of- thumb methods dependent upon individual opinion and often , prejudice , than by accurate , standard tests . This not only causes unwarranted price fluctuations , but injures both the producing and consuming industries by creating false ideas of the suitability of talc for various uses . It thus seems important that present tests be standardized and made uniform for the whole industry , and that new tests devised to fill the existing gaps .

Jul 1, 1920