Search Documents

By Lee W. Abramson

Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on several recently constructed tunnel projects. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed.

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

By R. S. Nutter

The results of designing, constructing, and laboratory testing of a modular, distributed, microprocessor-based mine monitoring and control system are presented. A standard computer communications protocol (DDCMP) was utilized throughout the system. Tests were performed on the utilization of a high-level language for programming mine monitoring and control systems. Laboratory tests were run on a combined air velocity/methane sensor.

Jan 1, 1980

By Hirst H, McAfee J

In December, 1934, Mr. R. Sussex extruded some silver lead alloy wires in order to determine their electrical resistance. After the determinations had been made each wire was threaded through a sheet of paper on which the composition was noted. The wires were placed in a more or less tangled mass in a cupboard in March, 1935. It was not until September, 1936, that they were re-examined, and it was found that during the eighteen months some of the wires had corroded very badly. It was not until March, 1938, that the wires and the corrosion product could be examined, and the results are given in the following pages. It is of interest to note that none of the numerous silver-lead alloys which have been used for creep testing in the rolled condition have shown a similarphenomenon. The silver content of the rolled alloys was, however, never greater than 0·1%.GENERAL APPEARANCE OF THE CORRODED WIRESThe wires contained 0·1% up to 28% of silver, and a general examination showed that the corrosion had progressed farther the higher the silver content. This can be seen in Fig. 1, which is a photograph taken in March, 1938, of typical wires at a 'magnification of five diameters. In the early stages the corrosive action seems to be localized and an area of grey, yellow or reddish brown powder appears. The grey corrosion product is by far the one, most frequently seen, and in the later stages the only one visible from the outside. The reddish coloured product is sometimes seen on the residual metallic centre when the grey product has been broken away.The irregular extent of the corrosion can be seen in Fig. 2, which shows (natural size) the 5% silver wire after standing two years. The corroded parts are seen to be much thicker than the slightly corroded ones. The corrosion product, being non-metallic, is quite brittle and falls away from the wire on bending. In the extreme case the' whole wire has corroded and presents a cracked appearance as seen in Fig. 1 (281% silver).An approximate idea of the extent of corrosion can be obtained by measuring the diameter of the corroded part. The original diameter in each case was ·050/ ·051 inches and in Table I are given the diameters of the corroded parts after Hand 3 years respectively. When the diameter...

Jan 1, 1941

By W. C. Peters, M. W. Pullen, C. A. Bays

During the past three and a half years considerable improvement in the techniques of solution extraction of salt has been made by the use of wells which are cross-connected by hydraulic fracture at the base of the salt. Fracture is initiated by the application of hydraulic pressure. Underreaming and perforating techniques are used to control initiation. The fracture is then extended by continuous pumping until a pressure communication is obtained. Pressure communication is followed by washing-through to obtain a low-pressure connection. Well construction using non-shrinking cements that will bond with the salt and with associated strata is essential to the process. The connecting procedure described permits solution to attack the salt deposit from its base upward, thereby permitting greater recovery, fewer well repairs, better saturation of brine, and overall economy of development and operation. The fracture method of cross-connection requires special pumping of the fluid and is limited by present experience to initial well spacings up to about 1200 feet. The method has been used in bedded salts and is applicable for wells in salt domes. Since spring of 1956, new developnents in salt extraction wells have followed procedures substantially different from those in prior use. Although multiple well systems, connected either by the natural consequence of the solution process or by undercutting under protective pads, have been used previously, the past three and a half years have brought about new designs and new operation procedures based on cross-connection of the wells using hydraulic fracture. To date these techniques have been applied largely in the bedded salt deposits of Michigan, Ontario, Ohio, West Virginia, and New York. To the writers' knowledge they have not been used in salt dome wells. The methods have not yet been in use for a sufficient period to permit any statistical comparison with the older methods. It is evident from experience to date that the methods result in higher recoveries, lower capital and operating costs, better saturation of produced brine, reduced well maintenance and repair, and in considerably fewer production units to insure

Jan 1, 1961

This report is the 24th in a series summarizing research on coal and related investigations3 by the Bureau of Mines. The coal programs of the Bureau of Mines include a wide range of theoretical and applied studies--such as fundamental studies of coal structure and properties, the development and evaluation of new mining techniques, and work toward more effective processing and utilization of coal. The scope of these programs is indicated, in topical outline, by the table of contents. These investigations are integrated into a broad but coordinated effort to develop information on coal that will benefit the coal mining industry and the coal consumer while promoting the wise conservation and utilization of our national coal resources. Any attempt to summarize in one volume the progress in all of the program areas indicated must necessarily be limited to a brief review of developments, without detailed reporting of the data. However, while the brief discussion in each section will present only the highlights of the Bureau's work during the year, details of many of the operations or investigations described here can be found in the publications cited throughout the text. Other work, reported here for the first time, will be covered in greater detail in later publications.

Jan 1, 1962

The Use of Automated Mineralogy to Interpret the Batch Flotation Performance of Merensky Reef Ore

Sep 13, 2010

By K. L. Paciorek

Organic materials utilized as cable Jacketing, cable insulation, standoffs, insulating boards and potting compositions were identified and d literature survey performed to obtain the required thermal oxidative and moist tracking data. Thirty representative compositions were procured and subjected to thermal and moist tracking evaluations. Tracking was found to invariably result in ignition or glow of the test specimen. Influence of parameters such as electrolyte strength and composition, temperature, conductor spacing, and electrode material were investigated. Volatile s produced by selected insulators on thermal oxidative and electrical stress were identified, quantitated, and their potential impairment action upon a current interrupter assessed.

Jan 1, 1980

By H. Tomlinson

"INTR0DUCTIONThis publication is a third of a series devoted to falls of roof and coal in coal mines of the Western States. It gives the results of examinations of the mines of the Rock Springs coal District of Sweetwater County, Wyo., which represent the principal coal beds therein and approximately 75 percent of total production of the State.A study was made of safety conditions at all the producing mines of the district and suggestions were offered the operators regarding methods and practices which would, in the opinion of the writer, provide additional safeguards to prevent accidents from falls of roof and coal.In presenting the subject, consideration must be given to such features as character of the coal beds, depth of cover. methods of mining, timbering practice, roof testing and supervision, and for comparative purposes to certain statistical matter bearing upon relation of accidents to their causes, tonnage produced, men employed, days worked, and lost days due to accidents during the 3—year period covered by this study.ACKNOWLEDGMENTSThe writer acknowledges the cooperation of the officials of the various coal companies, without whose assistance this work could not have been completed.F0UR REPRESENTATIVE COAL OPERATIONSThis report relates to four representative coal operations in the Rook Springs district of Sweetwater County, Wyo., which are referred to as mines A, B, C, and D. This group employs yearly an average of 993 men, representing 37 percent of the men in coal mines of the county, and has an average annual production of 1,484,373 tons, representing approximately 44 percent of the coal produced in the county. Figure 1 is a map of the Rook Springs coal district."

May 1, 1933

By Marvin S. Seppanen

Computer programers are often required to make modifications to unfamiliar Fortran routines. This Bureau of Mines report describes a computer program designed to aid the programer in such a situation by reorganizing: Fortran routines. This reorganization includes a sequential renumbering of the routine's statement numbers, a sequential renumbering, and relocation of format statements, an alphanumeric reordering of dimensioned and typed variables, a uniform pattern of text spacing, and a sequential numbering of the records in the final Fortran routine. The computer program has been extensively tested by the author and has proved to be a valuable tool for reorganizing Fortran routines developed under contract and later utilized by the Bureau, and for preparing routines for publication.

Jan 1, 1975

By Ronald W. Stingelin

This study undertook the development and implementation of a methodology for estimating the impact of coal seam interaction on the eastern bituminous underground reserve base as published in USBM Information Circular 8655. The effects of previous mining in multiple coal seam areas on currently mined and reserve seams are predicted as a percentage coal loss by an engineering assessment model called the Coal Loss Calculation Model. The model utilizes twelve input variables easily derivable from mine maps or other existing data sources and calculates the effects of subsidence and high-stress due to remnant pillars in the previously mined seam. Extensive literature review resulted in the identification, definition, and quantification of the critical variables of seam interaction. Export opinion surveys were made of mining experts, MESA mine inspectors, and coal mine operators. Statistical analysis was used to establish the redundancy of the critical variables and to develop a total coal loss prediction algorithm. A regional analysis resulted in the production of a series of thematic maps on coal characteristics and distribution. A derivative map showing the areas of commonality within the eastern bituminous coal region served as the basis for implementation of the coal loss calculation model. The model was developed and tested using data from four coal mines in western Pennsylvania and southern West Virginia.

Jan 1, 1976

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2002

By Antti J. Perala, Teemu J. Yli-Kovero

"Efficient use of land is constantly requiring more underground construction. Minimized execution time and disturbance to surroundings and nearby structures are essential benefits for all construction techniques. To meet the demands of a modern construction project, suppliers have to be able to provide high-quality and tailor-made products just on time. RD pile wall is a retaining wall based on drilled steel pipe piles which are connected to each other with special interlocking profiles. RD pile wall is a solution which enables penetration of overburden soil, dense fill layers including stones and boulders, and embedding into the bedrock in one single operation. Several test installations and laboratory tests have been made to develop the system and to test and improve the water tightness of the wall. Beside these tests, RD pile wall has also proven its reliability in almost 70 projects. Largest project so far has been Pasila Tripla project in Helsinki, Finland. A permanent retaining wall with surface area of 18,000 m2 (193,750 ft2), excavation depth of 21 m (68 ft) and over 17 m (56 ft) of water pressure was made with 711 mm (28”) and 406.4 mm (16”) pile sizes. Piles were delivered to site in one piece with lengths up to 33.5 m (110 ft).INTRODUCTIONExcavations in cramped city centers and in between of existing buildings and other structures are facing more and more challenges. Installation of sheet pile walls is often problematic or even impossible due to obstacles in ground from old structures and due to demand to extend the excavations to even deeper and harder soil layers. Also installations of secant pile walls are facing difficulties due to cramped construction sites and constantly tightening execution times.On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid- 1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall, was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers).PRINCIPLE AND MAIN BENEFITS OF THE METHODRD pile walls can be used in all soil conditions. Most beneficial the system is in extremely demanding soil conditions where the installation of traditional retaining walls is challenging or even impossible. The RD pile wall is a combination of drilled steel pipe piles and interlocking sections as shown in Fig. 1.Individual RD piles are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole (DTH) hammer using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings shown in Fig. 2."

Jan 1, 2017

By A. R. Jambekar

City of Bombay has been developed out of former 7 islands. Landmass of 434 sq.km. of Bombay, started looking inadequate for further growth and expansion of Bombay City. In order to develope twin city of New Bombay, State Government formed fully owned Company "City and Industrial Development Corporation of Maharashtra Limited", (CIDCO) in 1971 and entrusted it with planning and development including social and physical infrastructure of New Bombay.Hence, Trans - Thane Creek area is being planned and developed, to serve as counter-magnet to Bombay. Area of 343 sq.km located on the main land, is fast developing into a satellite community, for India's overcrowded financial capital. Thane Creek, running in almost North-South direction, separates Bombay City from main land and posed a significant barrier, to further expansion of city's sprawling suburbs, until, it was bridged for the first time in 1972. On the basis of traffic study, CIDCO decided to construct an additional road link across Thane creek to cope up with future projected traffic. This bridge will connect Airoli in New Bombay and Eastern Express highway near Mulund. Bridging the vast, exposed tidal Thane Creek, have always posed challenging conditions, during constructions of these bridges. In this paper, case history of deep open foundations provided for Airoli Bridge is presented.

Jan 1, 1996

By S. Mostaghel, V. Hernandez, S. Ge

"The automotive industry is under a constant pressure to reduce the weight of vehicles in order to reduce emissions and improve fuel efficiency. As such, there is an ever-growing demand for high strength and high ductility steel grades to meet the need for lightweight automotive components. Over the past decade, the production and application of 2nd and 3rd generation Advanced High Strength Steels (AHSS) as a lightweight material in automobiles has gained significant popularity due to their exceptional mechanical properties. However, the production cost of these high manganese steel remains high, partially due to the need of large amounts of ferromanganese as alloying material in standard steelmaking processes.The current study introduces a new and cost-effective technology for the production of medium- and high-manganese steels, where self-fluxed micro-pellets of manganese ore will be used as the source of manganese that can be injected into the steel bath. Prior to injection, these pellets are subjected to a pre-reduction process using a mixture of H2 and CO gases, where partial metallization of iron and manganese will occur. Direct injection of the pre-reduced micro-pellets provides less volatilization/emission and higher recovery of manganese, and is capable of producing AHSS with 6–18 wt% Mn.INTRODUCTIONAutomakers are constantly searching for lighter, stronger and cheaper materials in an effort to create safer and more fuel efficient vehicles. The introduction of aluminum alloys and polymer composite materials for automotive applications has been carving into what is traditionally one of the most profitable markets of the iron and steel business. The steel industry responded with Advanced High Strength Steel (AHSS)—a family of manganese containing steels which exhibit exceptional strength and ductility."

Jan 1, 2016

By Michael H. Wysockey

The load test program for the pile foundation at Soldier Field included static and dynamic load tests at four locations around the site. The dynamic tests were run with no knowledge of the static results, and comparison between the two is very good. It was necessary to use a special testing hammer (not the production hammer) to demonstrate capacity with dynamic testing. Over 90% of the piles were HP14x89 with a design load of 230 tons (18 ksi). The load tests showed a capacity in excess of 590 tons for all tests where sufficient set up time was allowed. The remainder of the piles were mostly HP 12x53 with a design load of 100 tons (13 ksi). The measured capacity of these piles was typically about 250 tons. One experimental HP12×74 pile with a nominal yield of 65 ksi held 730 tons (67 ksi) before failing.

Jan 1, 2002

Electricity will play a major part in providing energy services in the 21st century. Ecologically Sustainable Development (ESD), that is accommodating the needs of the present without compromising the needs of future generations, will provide a focus for optimising the use of electrical energy. Environmental externalities may redefine the cost structure of electricity. Strong corporate environmental management will ensure that current environmental objectives are met and that future ones, identified by the ESD process and environmental externalities accounting, can be developed and implemented by receptive business managers. This paper addresses the current environmental issues of electricity production. It outlines a management strategy for the SECV becoming a community leader in protecting the environment. ESD is discussed in terms of using non-renewable resources wisely, extending their availability and putting in place mechanisms which ensure their ultimate substitution by renewable resources and conservation. The paper explores options for dealing with costing environmental externalities, particularly in relation to greenhouse emissions.

Jan 1, 1992

By R. H. Grau

NIOSH’s Pittsburgh Research Laboratory is currently involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration (MSHA) compliance dust sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels, and controls being used. A summary of the mining operations, sampling procedures, resulting data, and suggested methods to improve the dust control will be provided.

Jan 1, 2002

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

By T N. Little

The author contends that geoscience is presently under-utilised in the rock fragmentation by blasting process. Before we can set standards in this area, the following is required: mine geologists need to gain a better understanding of the blasting process and the blasting team needs to obtain a better appreciation of geology. Both groups need to be informed of what can be done to improve blasting outcomes, why it is necessary and how it can be achieved. By working closely together, both the geoscience toolkits and blasting expertise can be applied and focused on priority blast sensitive issues, with potential to improve mine economics and safety. Finally, and ideally, mine geologists need to take a leadership role in raw rock mass data collection and data management, and invited to take an active role in rock mass related behaviour data collection, integration and presentation.This paper attempts to provide insight into all these prerequisites for setting a new standard for collaboration and mutual learning in this strategic opportunity area. The potential for blasting to leverage downstream processes is highlighted. Blasting objectives and blast design principles are introduced along with the required rock mass related inputs. Some hazardous geological materials and environmental conditions are described, along with how they can affect operational complexity.Four case examples are used to illustrate the need for closer liaison between geology and blasting professionals. The first related to grade control blasting, aims to demonstrate how a blasting geology approach can add significant value. Case example two demonstrates how geological models and bench face analysis can assist with fragment control. The third and fourth case examples involve an overview of two case studies where timely geological and geotechnical knowledge input and intervention into blasting activities may have reduced losses due to blast initiated open pit slope collapses.CITATION:Little, T N, 2017. Geoscience input into blasting operations – let’s set a new standard, in Proceedings Tenth International Mining Geology Conference 2017, pp 375–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017