Search Documents

By Jim Owens

The methodology of quarrying changed significantly in the Indiana limestone industry in the 60 years between Sept. 11, 1941 and Sept. 11, 2001. The former was the date of the Pentagon groundbreaking ceremony, while the latter was when the building was damaged by American Airlines Flight 77. So too, though to a lesser degree, did the machinery and methods used to fabricate the stone. The rededication ceremony on Sept. 11, 2002 marked the end of the Phoenix Project, as the rebuilding effort was named. The story of this remarkable project illustrates what the American construction(and Indiana limestone) industry can accomplish when working toward a common goal.

Jan 1, 2005

By Sergio N. Monteiro

Natural lignocellulosic fibers are successfully replacing synthetic fibers in many engineering applications. In addition to well-known conventional lignocellulosic fibers, others with promising properties are now being considered. The present work investigated the mechanical and structural characteristics of a relatively high strength fiber, curaua (Ananas erectifolius) from the Amazon region of Brazil. The results obtained from tensile tests confirmed the superior strength while scanning electron microscopy (SEM) analysis displayed features that justify the possibility of using the curaua fiber as an effective reinforcement for polymeric composites.

Jan 1, 2006

By Roberto J. Guardia, Ted Lewtas, Peter Rasmussen, Klaus Winkler

As part of the Lake Fort Smith Water Supply Dam Enlargement project, located in northwest Arkansas, microtunneling methods were used to install two side-by-side,1.53m (60-in) inside-diameter steel pipes between the intake structure shaft and the lake. The 46.6 m- (153 ft-) and 41.7 m- (137 ft-) long tunnels were excavated in Pennsylvanian sedimentary bedrock ranging from coarse sandstone to siltstone and shale-like claystone. The intake tunnels were constructed 18.3 m (60 ft) below lake level from the dry shaft. Special installation methods and procedures described herein were used to complete the lake taps. Installation difficulties that caused minor delays are also reviewed. After the excavation of the Intake shaft was completed, the two lake taps were installed in approximately ten weeks with the same microtunneling machine.

Jan 1, 2005

U.S. Gold Commission Established. - The President, with the authorization of Congress, has named a gold commission made up of 17 individuals, most of them Government officials, to study U.S. policies related to the role of gold in domestic and international monetary systems and report its findings and recommendations to Congress. U.S. Lead Exposure Ruling. - On June 29, the Supreme Court upheld the Government's right to set lead exposure levels for employees at the workplace. The Court ruled in favor of the Occupational Safety and Health Administration (OSHA) in a challenge by a group that alleged that OSHA had failed to conduct a cost-benefit analysis prior to issuance of the lead standards. It was the Court's contention that Congress did not require such an analysis when it empowered OSHA to establish workplace standards. The petition to the Court was made by the Lead Industries Association Inc., Battery Council International Inc" American Iron and Steel Institute, St. Joe Minerals Corp., and other lead mining and consuming firms.

Jan 1, 1981

By G. S. Scott

In the course of the Bureau of Mines investigation relative to the causes, behavior, and control of anthracite-mine fires, attention was directed toward the correlation between the temperature of oxidation and the gaseous oxidation products in the range of temperatures between 100° and 350°C4/. These tests, made on a high-grade anthracite to determine the amount of oxygen consumed and the mounts of carbon dioxide, carbon monoxide, hydrogen and methane evolved when air was passed through samples of the anthracite at various elevated temperatures, showed that the gases evolved and their relative proportions vary with temperature, constitute a means for determining the probable temperature of the anthracite, and thus permit detection of incipient heating beers dangerous fire hazard exists. As the relationships mentioned are affected somewhat by the amount of previous oxidation of the coal, it was deemed desirable to know to what extent they might vary owing to this cause. It was also considered desirable to have a means for estimating the extent of oxidation from the gas analysis, as this would permit a more accurate estimate of probable temperature. Finally, it seemed desirable to know how much the composition of coal might vary over an extended period of oxidation, since this was previously suggested5/ as a possible means for estimating the probable maximum oxidation temperature to which a sample of coal had been subjected.

Jan 1, 1940

By R. D. Sharpe

Gypsum wallboard manufacturers in the United States shipped 3.18 billion m2 (34.2 billion sq ft) of wall-board products during 2004 versus 2.93 billion m2 (31.5billion sq ft) in 2003. Following a historic high production of gypsum wallboard products in 1999, production decreased in 2000. But it has steadily increased during2001 through 2004. Wallboard production in the United States increased about 8.6 percent in 2004 from 2003. Following several years of a “building boom” of new wallboard plants and the expansion of the manufacturing capacity of several existing plants, 2004 was a relatively quiet year. However, several new plants and capacity expansions were announced or are in progress during 2004.

Jan 1, 2005

Interest in mining narrow, vein-type ones has increased world-wide during the last few years despite the fact that prices of metals have not risen in proportion as production costs of mining, such as labour and energy. In many mines, where narrow ones are mined, the mining technique and equipment used have been poorly mechanised. The mining methods have been cut-and-fill or shrinkage stoping. Pneumatic jack-legs have been used for drilling and slushers have been used for loading. The methods that have been used can be called the 'first-generation' methods. Work has been very hard for miners. It has been dangerous and exhausting. Production volumes of mines, and a s a result of that, also profits have been low.

Jan 1, 1990

By M. S. P. Rampedi

The paper reports on a vacation work project conducted at Khuseleka No. 1 Shaft, Anglo Platinum, where there was a need to optimize the transport of personnel to level 15 and below. Approximately 900 men per hour need to travel between the shaft and the start of the current chairlift system. Time studies were used as the major indicator of the extent of the current problem, and it is recommended that a new chairlift system be installed to cover the distance from the vertical shaft station at level 15 to the chairlift decline station on level 15. A capital cost of approximately R10 million is necessary to carry out the proposed recommendation. Khuseleka No. 1 Shaft has the capacity to wind 1070 people per hour, and the current labour complement going to the level 15 shaft station stands at 1570 employees; thus at optimum efficiency the proposed chairlift system could transport the entire shift to the start of the current chairlift system in only 1 hour and 45 minutes. Reducing the distance walked at the start of the shift may also have an impact on productivity.

Jan 1, 2012

By G. Naud, J. Robitaille, M. Buonvino, A. Veltmeyer, A. R. Laplante

"A B6 Falcon concentrator was tested on several systems: a synthetic magnetite-silica ore, a massive sulphide gold-copper ore, a fine gold-pyrite-silica flotation tail, and a high grade gold ore in a low sulphide gangue (cyclone overflow).The Falcon demonstrated its ability to achieve separation in all cases, but with varying degrees of success. For the magnetite-silica system, separation proceeds until the concentrate bed overloads, at a mass of 300 to 400 g of magnetite. Recovery increased with decreasing particle size, down to the 25-37 µm and in some cases even the -25 µm class. Bowl geometry (angle) and gangue size distribution were the most significant operating variables. Results with the massive sulphide ore were the poorest, with gold recoveries typically around 10 to 20% at very low upgrading ratios, 1: 1 to 5: I. Gold recovery from the fine flotation tail ranged from 30 to 70% at upgrading ratios of 5 to 15; actual plant application would require a continuous unit (Falcon C20). The high grade gold cyclone overflow yielded a wide range of gold recoveries, but a very consistent relationship between recovery and mass processed. A concentrate of 0.5% Au could be processed at a recovery of 50%.The paper also presents results of a C20 application to recover fine iron from a magnetic tail. The unit is capable of recovering approximately 70% of the fine liberated iron in a high density product, with modest upgrading below 105 µm, and virtually complete rejection of the + 300 µ m product."

Jan 1, 1993

By Steve Davidow, Ashely E. Evans, Peter M. Kandaris

"Annually thousands of deep foundations are constructed across North America supporting high voltage transmission line structures. However, a recent state of the practice survey by the Deep Foundation Institutes’ Electric Power Systems Foundation Working Group discovered that the electric power utility industry lacks consistent foundation design guidelines. The survey identified a wide variability in design assumptions, a minimal understanding of risk based analysis, and a need to standardize design methodologies. This paper summarizes the state of practice in electric system foundation design and proposes a framework for risk-based foundation design by accounting for uncertainty from both loads and resistances. Loads derived from electric system codes do not necessarily provide a compatible level of reliability for the design of foundations, as they are a mixture of probabilistic and deterministic values. Load uncertainty is derived from variability in weather conditions, structural models and material properties, typically accounted for by code derived overload factors. Resistance uncertainty arises from variability in natural soil properties, resistance models, subsurface construction techniques, material sampling methods, and limited observations. A consistent methodology is offered relating nominal resistance capacity (strength) to structure loads and service state criteria. Discussion also includes the need for risk-based assessments to account for non-structure load influences (fluvial loads, scour ground loss, liquefaction, etc.).INTRODUCTIONNearly 40 years ago the Electric Power Research Institute (EPRI) embarked on a major research effort to optimize reliability and economics of transmission line foundation design. Strategies focused on improvements in design models, site characterization, exploration strategies and testing to reduce uncertainty and variance in analysis. Transmission line engineers realized that safety and reliability advancements in design based on probabilistic approaches, with a focus on the unique nature of transmission line, could better control risk and cost.Some transmission line professionals took full advantage of these advancements, particularly where research led to improved software and models. Yet, even after two decades of extensive research, by 1995 the industry still had made little progress in changing design habits. The majority of designers were still characterizing sites via deterministic methods, using loads that may or may not relate to a consistent probability of occurrence, and applying a traditional global factor of safety approach (Phoon, et al. 1995). The following two decades have seen even greater developments in software and reliability-based analysis methods, but old habits seem to die hard as recent surveys show less than half of design professional quantitatively assess risk in their design process."

Jan 1, 2017

By R. R. Falier, W. E. Rice

"PURPOSE OF REPORTThis paper presents the results of a series of tests made by the U. S. Bureau of Mines in cooperation with The Ohio State University Engineering Experiment Station as part of an investigation on the use of fuel in kilns.This report is preliminary and gives only enough of the test data to illustrate results and show the reasons for the successes and failures of the method of firing investigated; fuller details will be included in the final report.PERSONNEL FOR TESTSThe investigation is conducted under supervision of P. Nicholls, supervising fuel engineer, of the United States Bureau of Mines, and G. A. Bole, research professor, of The Ohio State University. These tests were made under direction of W. E. Rice, associate fuel engineer, assisted by R. R. Faller, assistant fuel engineer, of the United States Bureau of Mines; H. C. Harrison, senior research engineer (until October 1, 1930), C. R. Austin, senior research engineer (since October 1, 1930), and H. K. Van Sohoick, junior research engineer, of The Ohio State University. M. J. Rice, field engineer, represented the manufacturer of the stoker.PURPOSE OF INVESTIGATIONThe general aim of the investigation is to develop more economical methods of using fuel in kilns and to improve the over—all efficiency of the process of firing by methods that will produce ware of better quality. One phase of this investigation is the burning of coal on an automatic stoker to gain the advantages of control, constant rate of application of heat, and ability to burn cheaper coal than can be used in the hand—fired furnaces of kilns. It a stoker in to be used it is desirable that the coot of the installation should be low, the control of operation simple, and the distribution of heat in the kiln as good or better than with hand firing. These desiderata were sought in the stoker and furnaces that were used for the tests described herein. The tests were made to determine whether it is feasible to fire a large kiln with a single stoker, whether the use of a single furnace simplifies control, and whether the admission of all the hot gam at the center of the kiln will give symmetrical distribution of heat."

Aug 1, 1931

By Jamal Rostami, Richard Kastner, Ahmad Ramezanzadeh

Improving the accuracy of the performance prediction models for hard rock Tunnel Boring Machines (TBMs) is important in estimation of the schedule and cost of tunnelling in related projects. The effects of rock mass on performance of TBMs has been studied extensively, yet due to the complex nature of the process, impact of many parameters influencing machine advance rate are not very clear and there is still room for improvements. More accurate estimates can be obtained by better understanding of operating parameters in various geological conditions and can lead to matching machine specifications with job conditions, optimizing machine performance, and avoiding long delays and downtime for increased productivity. This paper will offer review of two case histories including Queens Water tunnel in New York and KCRC project in Hong Kong. The analysis of the available field data, including the geological back mapping and results of laboratory testing of rock mechanical properties, machine operational parameters and achieved rate of penetration will be presented. This includes statistical analysis of available field data to provide a better understanding of the influence of rock mass properties on performance of hard rock TBMs as well as related formulas to improve performance estimates.

Jan 1, 2005

By C. C. Anderson

"While conducting investigations in connection with the helium program of the Bureau of Mines, the Cryogenic Laboratory has improved an apparatus for the rapid and accurate determination of the helium content of natural gas and gaseous mixtures derived from that source. The separation of helium is effected by the use of activated coconut charcoal which, when cooled to liquid-air temperatures, absorbs the nitrogen and other constituents of the gas, leaving the helium in a. spectroscopically pure state. This absorptive property of activated charcoal was discovered- by Dewar3/ in 1875. Several years later, while conducting their original researches on helium in natural gas, Cady and McFarland employed the charcoal method for the absorption and removal of the common constituents of natural gas and constructed an efficient apparatus in which this operation could be effected.4/ Shortly after initiating the government's helium activities during the World War period, the Bureau of Mines adopted, with Minor modifications, the Cady and McFarland apparatus and method of analysis. Seibel.5./ described this modified apparatus and method of procedure as part of a publication on helium-bearing natural gas. Subsequently, the Bureau's apparatus for helium analysis has been simplified and improved to facilitate more rapid and positive operation. The apparatus and method of procedure now being used by the Bureau of Mines Cryogenic Laboratory arc described in this paper.The personnel of the Bureau of Mines Cryogenic Laboratory has improved and brought the helium apparatus described herein to its present state of perfection. The writer's contributions have been-of minor importance, and he wishes to give the various members and former members of the laboratory staff full credit for the improvements they have made. He also desires to express his appreciation for suggestions and criticisms offered during the preparation of this paper to the following members of the Petroleum and Natural Gas Division, Bureau of Mines, which now includes the Amarillo Helium Plant and Cryogenic Laboratory: H. A. Cattell, chief engineer; C. W. Seibel, supervising engineer of the Amarillo Helium Plant; W. M. Deaton, chemist-in-charge of the Cryogenic Laboratory; and H. S. Kennedy.The quantitative determination of helium in a gaseous mixture is accomplished by the removal of the other constituents from the sample, either by chemical or physical Means, leaving only the helium which can be measured directly. Chemical methods, when applied to natural gas, require the burning of the hydrocarbons in oxygen, the, absorption of the resulting carbon dioxide in a caustic solution, the removal of the excess oxygen in a suitable solution such as an alkaline pyrogallate, and the elimination of nitrogen by sparking or by combination with hot calcium or magnesium.. Such procedures are very slow and tedious compared with the physical method which employs the absorptive property of activated charcoal to effect the separation of the other constituents from the helium."

Jun 1, 1934

By J. F. Barkley

"The fly-ash problem of the smoke-abatement engineer - who now might well be titled, ""Smoke and Fly-Ash Abatement Engineer"" - starts with the necessity for him to know what fly ash really is, what plants really create it, and how much is being created. Fly ash in this connection may be defined as all solid particles emitted to the atmosphere as a result of the combustion of fuel.COMPOSITION OF FLY ASHMuch can be learned about fly ash by studying samples with a strong magnifying glass or, preferably, a high-power microscope. As an example, figure 1 is a photomicrograph of an underfeed-stoker fly ash weighing 23.7 pounds per cubic foot, which passed a baffle-type cinder catcher and was caught by a Cottrell precipitator. Figure 2 shows a similar fly ash made at a higher stoker rating and weighing 36.2 pounds per cubic foot. The lighter ash contains more light, unconsolidated ash than the heavier. In both instances some of the ash has been fused to a glass, as is indicated by the spherical particles resembling marbles; however, the heavier dust contains more and larger spheres. With the faster burning and higher air pressures occurring at the higher burning rates, more of the larger fused spheres reached the precipitator.Such studies of fly ash frequently make possible correct determination of its source. For example, the Supreme Court Building, one of the finest of the Federal buildings in Washington, was having considerable difficulty with fly ash from some outside plant. It was thought to come from a nearby apartment house. A fly-ash trap was installed there, and care was taken in the operation of their underfeed stokers. The fly-ash nuisance continued. Microscopic examination of the fly ash found about the building compared with samples taken from the stack of the apartment house showed to the surprise of the accusing building superintendent that the present source was elsewhere. By the same means, the source was found to be a plant about ore-half mile away."

Sep 1, 1939

By Cocquio D. S, Bauchau C

In the course of an integrated airborne survey in 1975, a uranium-molybdenum deposit was discovered by Minatome Australia Pty Limited in North Queensland, Australia, approximately 70 km by road west of Townsville.The mineralization occurs in a welded tuff unit within the Carboniferous St James Vokanics. It is structurally controlled by a complex of subvertical east-west fractures and is exposed over a strike length of 350 m. Drilling has traced a further 150 m extension underneath a barren capping consisting of a thick pile of vokano-sediments. The maximum width of the orebody is 150 m, and its vertical thickness is approximately 100 m.The primary ore minerals are coffinite, pitchblende and molybdenite, accompanied by various alteration products (particularly uranium molybdates).The vein-type mineralization is considered epigenetic.A comprehensive program of surface drilling and underground exploration is in progress to establish the uranium and molybdenum reserves.

Jan 1, 1980

By Cameron J. Clayton

Cumberland Resources Ltd. is currently planning to develop the Meadowbank Gold Project located some 70 km north of Baker Lake, Nunavut in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of up to 6 main gold bearing deposits within relatively close proximity to one another which are planned to be mined primarily as a truck-and-shovel open pit operation and using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of 8 to 10 years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11 °C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site, and the physical environment, pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project.

May 1, 2004

By M. Karmis, C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self- advancing hydraulic supports. U. S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology have greatly increased productivity. Past trends are used to predict future technological directions.

Feb 24, 1997

By George L. Gates

[When clays e.re mixe~ "Jith "~later to nake mud fluids f'ol' use in :irilling ','Iells "for oil and gar: h;:r vue :;'0 tary me thee. t 18 liquid mij~ tUl"es have certair.. phypicr..l characteri.",t.ics that vary ",dth t e Qlldlltit.y find]

Jan 1, 1941

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987