Search Documents

By Y. Duraisamy

This paper presents the compressibility of tropical peat reinforced with cylindrical cement column. When a cement column installed vertically in peat, its compressibility was reduced because of the hardened skeleton matrix formed by cement particles bonding with adjacent soil particles in the presence of pore water. The effects of diameter, number of columns and cement proportions in cement columns on the compressibility have been investigated in this study. The results indicated that compressibility index Cc and Ca decreased with the increase in diameter of the cement column. Specimens with 45 mm and 60 mm diameter of cement column were cured for 28 days, after which they were subjected to Rowe Cell Consolidation test. Based on the results obtained, it shows that cement columns can successfully reduce the compressibility of tropical peat.

Jan 1, 2007

By Helmer Hedstrom

The purpose of this paper is to direct attention to the importance and the usefulness of phase measurements in electrical prospecting for ore, a subject about which virtually nothing has been published. The paper describes a new field method for ore prospecting, the "Turam" method, which makes use of phase measurements, and which has been used with great success for five years. Of the principal geophysical prospecting methods, the gravimetric and magnetic methods determine the direction and strength of the static fields of force of the earth. By seismic and electrical methods, fields of force are applied to the block of ground under investigation. By these methods a third parameter can be measured, besides the direction and strength of the field; namely, the time of arrival of the applied field at the different observation points. This time of arrival has been practically the only parameter measured in seismic work, while in electrical prospecting it has generally not been considered, the measurements having been limited to determination of direction and strength of the applied field. Phase Measurements In the most widely used of the electrical prospecting methods, those using alternating current, the time of arrival of the "electrical vibration" at the different observation points can be carried out as phase measurements. The phase angle measured then expresses, in part of one "vibration," or one cycle, how much the electrical vibrations at the observation point are out of step with those close to the source of the field. A phase lag of 45", for instance, means that the alternating field in the observation point is one-eighth of one complete " vibration," or cycle, out of step behind the field at the source. If the frequency is, say, 500 cycles per second, a frequency often used in electrical prospecting, a phase lag of 45' then means that the time required for the field of force to travel from the source to the observation point is 1/8 ' /500 = 1/4000 sec. Since the phase angle can be measured with an accuracy of a fraction, say one-tenth, of a degree, and the frequency can be considerably higher than 500, it is readily seen that the time of arrival can in this way be measured

Jan 1, 1940

By Helmer Hedstrom

The purpose of this paper is to direct attention to the importance and the usefulness of phase measurements in electrical prospecting for ore, a subject about which virtually nothing has been published. The paper describes a new field method for ore prospecting, the "Turam" method, which makes use of phase measurements, and which has been used with great success for five years. Of the principal geophysical prospecting methods, the gravimetric and magnetic methods determine the direction and strength of the static fields of force of the earth. By seismic and electrical methods, fields of force are applied to the block of ground under investigation. By these methods a third parameter can be measured, besides the direction and strength of the field; namely, the time of arrival of the applied field at the different observation points. This time of arrival has been practically the only parameter measured in seismic work, while in electrical prospecting it has generally not been considered, the measurements having been limited to determination of direction and strength of the applied field. Phase Measurements In the most widely used of the electrical prospecting methods, those using alternating current, the time of arrival of the "electrical vibration" at the different observation points can be carried out as phase measurements. The phase angle measured then expresses, in part of one "vibration," or one cycle, how much the electrical vibrations at the observation point are out of step with those close to the source of the field. A phase lag of 45", for instance, means that the alternating field in the observation point is one-eighth of one complete " vibration," or cycle, out of step behind the field at the source. If the frequency is, say, 500 cycles per second, a frequency often used in electrical prospecting, a phase lag of 45' then means that the time required for the field of force to travel from the source to the observation point is 1/8 ' /500 = 1/4000 sec. Since the phase angle can be measured with an accuracy of a fraction, say one-tenth, of a degree, and the frequency can be considerably higher than 500, it is readily seen that the time of arrival can in this way be measured

Jan 1, 1940

By J. Moema, L. Mampuru, M. Phasha, D. Mkhonto

The global liquified natural gas (LNG) storage market size is projected to reach USD17.5 billion by 2025. Currently, owed to its high toughness, tensile strength, and excellent weldability, the 9% nickel steel is the most used in building infrastructure for cryogenic applications such as the construction of tanks and pipes for storage and transportation of LNG. However, this alloy is not readily available because of its complex production process and high cost. This provides an opportunity for suitable alternative materials to build infrastructure for cryogenic applications. Among strong contenders is the Fe-Mn based alloys, which have sparked global interest due to their desirable properties such as relatively lower density, low cost, high toughness and strength, due to a high manganese (Mn) content. These attractive properties render Fe-Mn based alloys preferred candidates to replace traditional steels in engineering applications in which strengthweight ratio is critical. In response, as a build-up to designing and developing austenitic Fe- Mn alloys, the present study employed density functional theory (DFT) based first-principles computational materials modelling technique to investigate the structural, thermodynamic, and magnetic properties of binary Fe-Mn alloy composition in competing FCC, HCP, and BCC crystal structures. Using this approach, it was possible to unravel the key underlying elastic properties that are directly correlated to experimental tensile strength and high toughness in binary Fe-Mn alloys. Besides successfully validating the existing experimental data, the current predicted properties and the deployed approach will serve as a benchmark from which further alloying required to improve other properties will be conducted.

Mar 4, 2025

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

By V. Kamavaram

Keywords: Recycling, Aluminum Metal Matrix Composite, Ionic Liquids, BMIC Recycling of aluminum metal matrix composites (MMC) via electrolysis in ionic liquids at near room temperature was investigated. The electrolytic melt comprised of 1-butyl-3-methylimidazolium chloride (BMIC) and anhydrous AlCl3. Impure aluminum composite (Duralcan MMC Al-380, 20 vol % SiC) was electrochemically dissolved at the anode and pure aluminum (>98%) was deposited on a copper cathode. The deposits were characterized by scanning electron microscope, X-ray diffractrometer, and mass spectrometer. The influence of various process parameters such as concentration of electrolyte, and applied cell voltage on the recycling process was studied. The recycling process yielded current densities in the range of 200-500 A/m2, and cathode current efficiency of about 85%. The results indicated that impurities such as Cu, Si, Ni, Fe, Mg, Mn, and SiC particles were removed as anode residue. Energy consumption of about 3.7-6.3 kWh/kg-Al was obtained at a cell voltage of 1.0-2.0 V and cell temperature of 100 ± 5°C. Low energy consumption and no emission of pollutants are the two main advantages of this process compared to present recycling processes.

Jan 1, 2005

By L. D. Roper

"This paper introduces novel comminution flowsheet concepts involving a novel apparatus, eccentric-high-pressure-centrifugal-comminution (eHPCC), and forthcoming advantages to the international mineral processing community. eHPCC is one-machine synergising high-pressure-rolling surfaces, high-intensity-attrition and centrifugal classification. eHPCC has demonstrated: an absorbed power- intensity of 4 MW/m3; receipt of lump feed whilst producing 80% of product particles less than (p80) 120 µm (choke-fed, dry, open circuit without grinding media; an inert comminution environment); tramp metal tolerance, and a minimum embodied-free-energy saving of 15% as compared against conventional comminution (this comparison withstanding 133-times difference in throughput). Furthermore, this paper introduces: process design and operating characteristics of eHPCC (wet, dry, with and without grinding media); reline considerations (vertical-lift without confined-space). The international mineral processing community is invited to consider eHPCC as an alternative to conventional comminution circuits and/ or complimentary so as to enhance existing process flow sheets.INTRODUCTIONEccentric-high-pressure-centrifugal-comminution (eHPCC) was conceived in 2013 (Patents pending) and has the potential to eliminate the in-efficiencies and complexity of conventional tumbling mill circuits. During the development and testing phase eHPCC demonstrated improved energy efficiency and sustainability offsets.eHPCC will compliment any upstream feed source, be it run-of-mine (ROM), primary crushed rock, or any other conventional comminution stream such as tumbling mill oversize. Another novelemerging technology, Conjugate Anvil-Hammer Mill (CAHM) (Nordell and Potapov, 2011), receiving ROM, will be a complimentary open-circuit feed to eHPCC for very high throughput flow-sheets.eHPCC may compliment downstream process requirements through selective mineral liberation. Selective mineral liberation is entirely feasible as the ore is comminuted upon itself (autogenously) in the high pressure zone caused by the synchronous rotating components."

Jan 1, 2016

Combined Flow Sheet for Treatment and Recycling of Municipal Solid Waste (MSW) with Complex Morphological Composition

Sep 13, 2010

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermophysical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous cases is modeled with walls, each having a different set of thermophysical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By Pefer F. Stacey

This paper considers some of the trends in slope design technology that are emerging as we approach the 21st Century. While the ability to design stable slopes has unproved greatly over the past 20 years, trends towards steep short-term slopes for small highgrade orebodies, and very high slopes for mega-pits centered on low grade deposits are starting to indicate limitations in available technology.

Jan 1, 1994

By K. C. Dean

A flotation method was developed by the Bureau of Mines for concentrating pollucite, a cesium-aluminum-silicate mineral that may contain from 20 to 40 percent cesium oxide. Separation of the pollucite from three typical ores was achieved by froth flotation of the associated micas, feldspars, and other gangue minerals, using sulfuric and hydrofluoric acids and a cationic-type collector. A low-tenor, 8 percent cesium ore from Maine was upgraded to 20 percent cesium with recovery of 87 percent of the cesium. Relatively high- grade ores from Canada and Southern Rhodesia were beneficiated at lower ratios of concentration to 28 and 29 percent cesium content respectively with recovery of over 92 percent of the cesium. In addition to concentrating the cesium content of ores, the method also effectively separates cesium from sodium, potassium, and lithium, and in certain ores from rubidium. This is accomplished by selective froth flotation of the alkali metal-bearing gangue minerals such as lepidolite, other micas, and feldspars. Since the alkali metals, especially potassium and rubidium, are difficult to separate chemically or thermally from cesium to prepare high- purity cesium products, separation by physical mans is important.

Jan 1, 1962

By M. Ng

As part of a long-term study of titanium minerals processing being undertaken by the Julius Kruttschnitt Mineral Research Centre, techniques have been developed to measure the resistivity of ilmenite, rutile, zircon and other associated minerals. The techniques have proven reproducible and have allowed the measurement of resistivity under conditions of varying temperature, surface condition and surface moisture adsorption. The measured values can be linked to the separability of the minerals in the dry plant, and hence are useful as a diagnostic test for existing plants when performance deteriorates, or for greenfield sites to investigate potential problems. One of the major problems in electrical separation of titanium minerals is surface coating on the mineral grains. Coatings can make normally conductive minerals such as ilmenite and leucoxene behave much more like non-conductors. Electrical separation of surface contaminated ilmenite from non-conductors then becomes extremely difficult unless the surface contaminant is first removed. The resistivity measurement technique was used to evaluate the effect of surface cleaning on the resistivity of ilmenite and zircon from a Western Australian deposit which will shortly be in production. Ten different attritioning methods were evaluated, ranging from simple rinsing inwater to chemical attritioning in sulphuric acid combined with ultrasonic leaching. A roasting and quenching step was also investigated. As would be expected, the gentler treatments, such as rinsing in water or Calgon, had only amoderate effect on the ilmenite surface coatings. Ilmenite resistivity decreased by about 1 order of magnitude from 5.6 x108?m to between 2.5 and 4.4 x107?m. More intense treatments had a much more pronounced effect. The most effective, reduced ilmenite resistivity to 6.5 x105?m or three orders of magnitude. Zircon was relatively unaffected by any of the attritioning methods, with only a small increase in resistivity observed from 8.0 x1012?m to 2 x1013 ?m. The results show that measurement of mineral resistivity allows the effect of surface treatments to be easily quantified in a way that has benefits for greenfield site development where only small samples are available for testing. The effect of surface moisture has also been investigated using resistivity measurements. Measurements were made on zircon in an environmental chamber in which both humidity and temperature could be closely controlled. Zircon resistivity at 60 deg C decreased from 6 x1011?m at 5% relative humidity to 8 x108?m at 95% humidity. Moisture content and moisture re-adsorption from dry of zircon and number of other minerals were measured using a Mettler moisture analyser. Zircon adsorbed the least amount of surface moisture (0.05–0.09%) but re-adsorbed moisture from dry the fastest, reaching 98% of the original level in 10 minutes. Leucoxene adsorbed the most moisture (0.67%), but was much slower re-adsorbing this moisture from the dry state, reaching only 63% of the original level in 10 minutes. The difference was attributed to the surface characteristics of the grains, the leucoxene being much more porous than the zircon examined. The resistivities and differing rates of moisture adsorption can be used to quantify the effects of changes in atmospheric conditions of the performance of electrical separation in dry plants.

Jan 1, 2003

"The Merensky Reef is a platinum group minerals (PGM) bearing reef in the Bushveld Igneous Complex in South Africa. The reef has been treated by bulk PGM and sulphide flotation with the aim of maximisingthe valuable minerals recovery and gangue minerals rejection.Synthetic water with a calcium concentration of 80 ppm and 500 ppm was prepared and the flotation results obtained were compared to a simple electrolyte in order to determine the effect water quality has on pentlandite and pyroxene surface alteration and, ultimately, floatability. During the study, the possible effect of interactions between the minerals investigated and Ca2+ ions in the presence of sodium isobutyl xanthate was studied at pH 6 and pH 9 by means of zeta potential determinations, microflotation tests and ToF-SIMS analysis.The results obtained on 1:1 pentlandite-pyroxene mixtures showed that the quality of process water plays an important role in flotation. The flotation recoveries of pentlandite and pyroxene were lower in synthetic process water compared to those obtained in a simple electrolyte solution."

Jan 1, 2003

By E. W. Davis

THIS nation has been depending upon the Lake Superior iron ranges for most of its iron ore requirements for over half a century. Furthermore, it can continue to draw the major portion of its ore requirements from the same source for another century or more, but to accomplish this, great changes must take place in the present ore mining industry. Preliminary preparations for these changes are now underway and in the next few years decisions of far-reaching importance must be made. But to understand the situation, it is first necessary to know something of the nature and occurrence of the Lake Superior iron formation. So far as is known, the merchantable grades of iron ore remaining in the various Lake Superior ranges are as shown in Table 1, which shows that

Jan 1, 1947

This paper presents the results of an experimental study undertaken to demonstrate the feasibility of using silica sand as a grinding media in stirred ball mills for ultra-fine coal grinding. Laboratory batch as well as bench scale continuous tests indicate that the use of silica sand can reduce the energy consumption by 50% and more over its steel media counter-part. Moreover, this approach has been found to eliminate the disadvantages observed with grinding using steel media such as high replacement cost, contamination of coal through media wear, greater degree of coal oxidation due to higher slurry temperature and greater level of noise dissipation. Additionally, coal-sand attrition system reduces the manpower time required which is often spent towards cleaning and storing of steel media in inert atmosphere to avoid rust and corrosion problems.

Jan 1, 1991

By Dale S. Preece, Ruilin Yang

"Air-decks are often employed for presplitting along the final highwall of a blast and are sometimes also included at the bottom or in the middle of explosive columns in the production portion of a blast. Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidlyattenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that theresulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of theexplosive."

Jan 1, 2017

By D. Küster, G. Franken, P. Schütte, J. Vasters

The CTC (Certified Trading Chains) mineral certification system has been piloted in Rwanda since late 2008. CTC project implementation is jointly driven by the Federal Institute for Geosciences and Natural Resources (BGR) and the Rwanda Geology and Mines Authority (OGMR), in cooperation with other national stakeholders. Five Rwandan mineral producers participate in the CTC project with their flagship mining concessions. Based on independent third-party audits, CTC certifies supply chain due diligence measures of these companies engaged in the artisanal mining sector through on-the-ground assessments of mining conditions, transparency, as well as mineral origin and traceability. The CTC system thus allows responsible mineral producers and their clients to verifiably demonstrate supply chain due diligence and good governance in conflict-affected and high-risk areas.

Jan 1, 2011

By Frank H. Madison

The percentage depletion deduction on Federal Income Tax Returns under the provisions of the 1939 Internal Revenue Code and of Sections 611 to Section 615, inclusive, of the revenue act of 1954, have created innumerable administrative difficulties, and a new interpretation of "gross income from the property" in that the Courts have expanded the ideas of what constitutes "gross income from the property" to a degree unheard of and unthought of prior to the enactment of these two codes. Originally, under the Revenue Acts of 1917, 1918, and 1920 depletion was allowable, based upon mine valuations as of March 1, 1913; if the mine was owned prior to March 1, 1913; upon cost, as of the date of acquisition if purchased subsequent to March 1, 1913; and upon a "discovery" basis if the mine was discovered after March 1, 1913, The "jab" for mine valuations as of March 1, 1913 and for discovery valuations and depletion was not as bad as it has been made out to be. Thousands of valuations and estimates of reserves were made and agreed upon between taxpayers and Internal Revenue Service engineers and as the years went on the answers have been found to be "reasonable." However, human nature being what it is each case was a battle of wits - of a sort - and many resulted in severe differences of opinion and litigation. As tax rates increased the situation was not bettered. I could talk for several hours on this phase of depletion but it is all past now andwould not give any real service or better understanding of the matter.

Jan 1, 1958

By Y. M. Jubeli

"Abstract - Gamma-ray spectrometry, an effective tool in geological mapping, was used to define boundaries between various lithological formations in three adjacent areas of Central Syria, namely, the Syrian Desert, Ar Rassafeh Badiayat and the Northern Palmyrides mountains. This paper describes the role of an airborne gamma spectrometric survey which was orginally undertaken to assist uranium exploration. Interpretation of the total count data obtained through the survey has led to significant modifications and corrections to the previously published distribution map of the palaeogene phosphate rocks.Another important result of the survey is the discovery of four previously unknown phosphorite horizons in the Rasm Al-Aawabed area of the Northern Palmyrides. In addition, previously unknown phosphatic horizons are outlined in the other study areas. The importance of this technique as an effective prospecting method, not only for U but also for exploring for the economically important phosphorite formations in Syria, is emphasized. Furthermore, its role in geological mapping is stressed, especially in areas that lack sufficient geological data."

Jan 1, 1997

By Y. M. Jubeli

"Gamma-ray spectrometry, an effective tool in geological mapping, was used to de?ne boundaries between various lithological formations in three adjacent areas of Central Syria, namely, the Syrian Desert, Ar Rassafeh Badiayat and the Northern Palmyrides mountains.This paper describes the role of an airborne gamma spectrometric survey which was originally undertaken to assist uranium exploration. Interpretation of the total count data obtained through the survey has led to signi?cant modi?cations and corrections to the previously published distribution map of the palaeogene phosphate rocks.Another important result of the survey is the discovery of four previously unknown phosphorite horizons in the Rasm Al-Aawabed area of the Northern Palmyrides. In addition, previously unknown phosphatic horizons are outlined in the other study areas. The importance of this technique as an effective prospecting method, not only for U but also for exploring for the economically important phosphorite formations in Syria, is emphasized. Furthermore, its role in geological mapping is stressed, especially in areas that lack suf?cient geological data."

Jan 1, 1997